RV042G treats of several IP WAN/secondary

Similar Questions

• RV042G - access modem connected to a WAN port

  Hello

  I've set up my RV042G with that one line WAN currently using a modem Alice IAD to connect to my ISP. This unit has an own web server for configuration currently configured IP 192.168.0.1. The dual WAN router got the address of WAN IP 192.168.0.4 (the fixed address) and a LAN IP 192.168.0.5. Now, I need to access the modem from time to time for maintenance but can not reach address 192.168.0.1. The RV042G can be configured to allow communication between the modem and the LAN devices? I tried to put a static route, but that did not help. I'm certainly not a network expert.

  Thank you

  Mike

  Hi Mike, if your modem is able to log on locally, then the LAN RV042G subnet should be different from that of the modem LAN subnet. Given that your modem is 192.168.0.x your RV042G can be 192.168.1.x for LAN. So the RV042G WAN is 192.168.0.x.

  This should be your goal.

  -Tom
  Please mark replied messages useful

• Connections RV042G Dual WAN

  We are a Cisco DPC3825 provided by our ISP cable modem connection.  It has been configured to act as a switch only.  They provided us with 2 static IP addresses.

  When each WAN port is connected individually, all right.  I see the IP addresses on the respective WAN port, and it works fine.

  When I connect the two WAN ports to the modem at the same time, I see a large amount of traffic between the WAN ports, as indicated by the port LEDs, and the RV042G becomes totally inadmissible through its web interface.

  How can I get the RV042G working with two connected WAN ports?

  Hi Rory, I'm not sure that the CPD is designed to aggregate in this way traffic. I wouldn't be surprised if he made a loop network, especially if you see a lot of broadcast or multicast packets.

  The most typical deployment has usually 2 connections that are unique modems.  I would suspect your 2 static IP addresses are on the same subnet / block ip that the router do not know how to react to load balance this scenario since he's going to the same destination in turn causing a loop until resources are consumed.

  -Tom
  Please mark replied messages useful

• FVS336Gv3 multi-NAT inbound firewall rules does not

  I have about 30 Netgear FVS338 and a few FVS336Gv2 routers in use. I use for firewall and provide multi-NAT between industrial machines and WAN. The configuration was changed on Gv3 models and I can't get an answer behind the firewall or router in the diagnostics page when you use the WAN address.

  In the examples below the WAN is 10.62.

  

  Figure 1. Two different devices with two different configuration options.

  

  Figures 2 and 3. The first is bad - it would only connect from this address. Have I set up another correctly to the NAT WAN to LAN 10.3.110.215 address 10.62.31.55 address?

  Q1: Is Figure 3 configured correctly?

  Q2: Why is it forcing me to create a range of addresses? On the older routers, I had the opportunity to address.

  Q3: Is anyone aware of any problem with this router?

  For anyone having the same problem, the FVS336Gv3 requires the manual addition of each new address WAN-side. He is buried in the menu structure:

  

  Figure 1. Network configuration | WAN settings | WAN configuration. WAN1 - Edit.

  

  Figure 2. Select the secondary addresses.

  

  Figure 3. Add the required WAN addresses.

  Now configure the inbound firewall rules:

  

  Figure 4. Security | Firewall rules. Add or change. Note that the WAN secondary addresses are available in the drop-down list address WAN IP.

  Password

  There seems to be a problem with this router about the session timeout. I got them several times on the navigation menu and log on again and renavigate. Idle time-out is set to 90 minutes. I never saw this problem on routers earlier.

  Also, note that the password field now has a limited character set. for example, it does not accept ' $'.

• X 61 Tablet wireless towers off accidents / on the screen Rotation

  New and strange problem with my X 61 (vista race, perfectly up-to-date, 4 GB ram, etc.)

  When I turn in slate mode, the wireless disconnects and refuses to properly reconnect until I reboot. I checked this behavior several times. More confusing: the icon for wireless connection on the right side of the taskbar remains in connected mode, but if you click on it, it will not give you used windows control panel allowing you to access the Networking screens. Still unknown, if you close physically radios with the switch located on the front, the radio LED remains on and using Fn + F5 to bring up the screen of the radio, does not allow me on the radio or turn off or cycle.

  Possible cause: I uninstalled "Access Connections" because it is nothing but trouble for me:

  It may be a variant of the old 'display cannot operate wireless WAN secondary when landscape mode' is active message that I used to get. Basically, this computer does not WAN wireless, never, but for some time, when I tried to use the secondary display landscape in slate mode, it gives me this message and to reactivate the screen in a different direction. It was clearly unacceptable, and I uninstalled the logins that seems to fix the problem.

  With a recent automatic update of lenovo, he reinstalled logins and started this problem again, this is why I uninstalled it again. But now, it.

  Anyone see this? I think remember that screen orientation has been accused of being tied to ActiveProtection (which should automatically detect the orientation of the computer and rotate the screen accordingly, thing which never worked on my machine, this is why I also uninstalled that.)

  It seems impossible that Lenovo could fudge wifi wireless connectivity by writing software that binds the radios to useless (non-functional) modules as protection against shock, but the only thing that has changed over the last few days is my uninstall these programs, so I can't think of any other reason, suddenly, this radio would operate this way.

  Funny you should post this because I literally just signed up to this forum so I could add a post for this problem (such as a temporary solution) in the hope that Lenovo would quickly remedy the situation.  I'm kind of a newbie tech and only recently started problems my computer on my own please excuse any lack of jargon appropriate during this post.

  Anyway, the problem I thought that (like you) has been the connections access version 5.02 update version which was recently published by Lenovo automatically updates for my tablet.  So I uninstalled 5.02 and reinstalled the old version 4.52.  After restarting my computer, I tried turning my tablet mode screen has frozen--> the wireless disabled, connections to wireless LED remain lit and would evict me of secondary landscape mode with the wireless enabled, even if I tried to disable the wireless with the button on the front of the keyboard.  Same problem exactly where you have posted.

  Then I went to my ThinkVantage System Update and looked at my history of update to see what other recent updates may have been originally.  I came across a version called "Intel Wireless WiFi for Vista 32 bit" 12.00.4000.  After doing some research on the Lenovo Web site, I found the driver:

  http://www-307.IBM.com/PC/support/site.WSS/document.do?sitestyle=Lenovo&lndocid=MIGR-70505

  In any case, I thought that it would be worth to back off this update to try to see if it is solved the problem since the update and was installed on my computer was the same exact day I started to notice problems with my wireless in slate mode.  Anyway, long story short I used the tutorial at the bottom of the page of the pilot (pasted below) to access my Vista Device Manager to find the wireless driver and then back to an earlier version:

  Determine which version is installed

  1. Click Start, then click Control Panel.
  2. Click system and Maintenance.
  3. Click on System. In the left pane, click Device Manager.
  4. Click network adapters.
  5. Double click on in the software of Intel (r) PRO Wireless WIFI.
  6. Click the driver tab. The driver version will be displayed.
  7. (Now restore it previous version!)

  Ok.  So once this process is finished, I rebooted and everything worked perfectly again.  However, I have never reinstalled the new version 5.02 access connections and am always running the pilot 4.52.  I didn't mess with it more and push my luck by reinstalling the 5.02 connections more recent access again because it seems to work with 4.52.

  I'm sure that, after losing three days on it to try to fix the problem that it is the responsibility of the new version of the driver "Intel Wireless WiFi for Vista 32-bit" 12.00.4000.  Please if someone Lenovo bed this thread we should try and patch this driver ASAP?  I'm a student and this problem set my Tablet out of operation for several days, which was very frustrating as I rely on my tablet every day to take notes and internet access in the classroom and clinic.  Fortunately, I found a solution but not really a permanent one.  In any case, let me know if this help - it worked for me and I hope it will help someone else out there with the same questions without phone/tablet.  Good luck - and thanks to Lenovo for additional help with this.

• VI Packager to pick up a big mess

  Hello

  I inherited a mess.

  I have used Labview 6.1 in the past, but I'm far from an expert, but I'm used to and understand almost everything.

  LabVIEW 6.1 had no project manager in former days.

  I have a VI that operates a piece of test equipment that is critical to our business. (I'll call him 'App')

  She was treated by several people on a journey of several years.

  -It was created in Labview but do not know what version.  It should always run using LV 2010 present environment (not a runtime engine).

  -He will NOT run in LV 2012.  I've tried it.

  -It was NOT created by using the project manager.  It's a bunch of VI and VI Sub and things that Labivew has decided that he needs.

  -He was always performed by using the LabView developers environment (it was never integrated into a standalone application.)

  -It is big enough and in all directions.

  -It has a scale, (NOR-DAQmx) and fuctions and calibration DAQ, files that I also keep intact.

  My question is: How can I "collect" all the bits and submarines in a project so I can compile in a stand-alone package?

  When I look at the main shaft of the VI, it called stuff in every sense, and these files that are in every sense are not in the folder where the main VI.

  Should change to LV2012, I'm afraid that if I Pack properly this application, I will never lose it.  Can I rev the application until 2012 of Labview?

  Is there a way to gather all this in a nice neat package by using the project manager or is there a 3rd party Packer that I can use?

  Specific useful responses are always very much appreciated.  Comments out of place, not so much.

  Lebowski

  If she should always run in LV2010 then continnue your development in LV2010.

  If you want to "Project-ize" the application then take an empty LabVIEW project and add the main VI. Under dependencies will be placed all the subVIs called. You can then use this list to drag - move add up all the necessary subVIs in space project, using virtual folders to make the easy to navigate look.

  To ensure that you have a good copy, use the feature save project as to make a copy of the project elsewhere (for example, a network location, or a memory stick) which will give you the option to include all dependencies.

  Cleaning the location of files, switch the elements of files project tree by selecting CTRL + E on each dependency and place the disk each dependency in a more preferable location. You can book this process for the cloned project to make sure that you don't move screw in the original application (which can be expected for other applications).

  Once here, you can then consider examines why it does not work in 2012, but if you need to work in 2010 I develop in 2012 because the conversion of backs can be heavy

• Huge catalog of 100 pages in size - using InDesign CC - files is 492 GB!

  I have a catalog InDesign CC 100 pages, which is 492 GB! Each page has placed the Illustrator CADs in one. Format HAVE. Is there a way to prepare the CADs Illustrator before placing them in InDesign that will reduce the overall size of the InDesign file and finally the exported PDF file?

  Any help would be greatly appreciated!

  The InDesign file contains 647 files, a combination of Illustrator CADs (.) IA)

  I guess I'm looking for a miracle, hoping that there is something I can do in InDesign or Illustrator to treat CAD several files at the same time?

  What is the output destination? If treated right you could solve the problem of file size InDesign and PDF by pixelation CAD drawings to a high resolution. You would have to watch out for the black conversion lines in 4 colors and you may need more than 300 typical PPI, but you would probably get a lot of compression, export to PDF format to repeat the background pixels. The rasterization could easily be scripted or batch.

  You can also try the export at .idml and reopening of idea. If everything is placed and connected, 492 mb still seems high.

• Need help to replace a physically C drive on several computer disks. I can't LOOSE the data on the secondary drive.

  I got 2 hard drives, a small disc with XP Pro and a big drive for storage and memory intensive programs. The disc is dead - physically (he's grinding wheels), not because of software problems. I managed to boot from the XP disk and copied as much as possible on an external drive to install on a new hard drive. Externally will not take the backup file. After that I restarted depui the XP disc, my secondary drive is no longer recognized. I copy the contents of the C drive on an external drive. Here are my questions:
  1. can I ghost the info on a new hard drive and skip the installation? Reason I have CS3 on drive F, but it components installed on the C drive (where CS2 was before I upgraded). I do not have my Adobe CS3 here records because it allowed multi, and my records are currently out of State with the other licensee.
  2. If I install the new disk, starting from the old drive with XP disc, can I ghost? (I have a tour customized for several readers) When I started the drive C before - he tried to install on my F drive. I have not installed (I can't lose the files on drive F), and now the computer does not recognize the drive. I bought a Seagate drive and they have great software for installation - so I'd like to ghost it. The XP disk reduced to nothing the new drive hard as he did the F drive?
  and finally, question 3. When the new drive, I get up and running, can I sign out the F drive, plug it back and Windows will see it? CS3 & Quark will still work if I have to do a fresh install?

  1. can I ghost the info on a new hard drive and skip the installation? Reason I have CS3 on drive F, but it components installed on the C drive (where CS2 was before I upgraded). I do not have my Adobe CS3 here records because it allowed multi, and my records are currently out of State with the other licensee.

  2. If I install the new disk, starting from the old drive with XP disc, can I ghost? (I have a tour customized for several readers) When I started the drive C before - he tried to install on my F drive. I have not installed (I can't lose the files on drive F), and now the computer does not recognize the drive. I bought a Seagate drive and they have great software for installation - so I'd like to ghost it. The XP disk reduced to nothing the new drive hard as he did the F drive?
  and finally, question

  3. when the new drive, I get up and running, can I sign out the F drive, plug it back and Windows will see it? CS3 & Quark will still work if I have to do a fresh install?

  Hi jdohugh,

  Thanks for posting. If I read your post correctly your hard drive with your operating system on it died, so you lost your operating system and do not have to reinstall but you try to get down the important data before the reinstall.

  1 Q: can I ghost the info on a new hard drive and skip the installation? Reason I have CS3 on drive F, but it components installed on the C drive (where CS2 was before I upgraded). I do not have my Adobe CS3 here records because it allowed multi, and my records are currently out of State with the other licensee.

  A. Si your drive with your operating system does not work, I do not think you can ghost it and reinstall as the image would not work. With Adobe CS3 disks, you will need to contact Adobe and get them to perform the installation of additional supports. Simply copy the files likely will not work to reisntall the application.

  2. Q. If I install the new disk, starting from the old drive with XP disc, can I ghost? (I have a tour customized for several readers) When I started the drive C before - he tried to install on my F drive. I have not installed (I can't lose the files on drive F), and now the computer does not recognize the drive. I bought a Seagate drive and they have great software for installation - so I'd like to ghost it. The XP disk reduced to nothing the new drive hard as he did the F drive?

  A: as I said in question 1 if your operating system drive does not an image would most likely fail or be corrupt. If read correctly the other part of the question you the system tried to start installation on your f:\ that matches your drive program and now you cannot access the files on it? With the last part of this question, you will need to contact Seagate to see what makes their software, I'm not sure what you're trying to accomplish by using.

  3. Q. When the new drive, I get up and running, can I sign out the F drive, plug it back and Windows will see it? CS3 & Quark will still work if I have to do a fresh install?
       
  A. Si you reconnect an extra drive to XP, the operating system should see it regardless of what it was connected to previously. With regard to your programs, if it is a new operating system you load then Yes, you will need to reinstall these applications on the operating system, and they should work with no problems provided that the drive is working correctly.

  I hope this helps. Let me know if you have any additional questions.
  Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• rv042G multiple s on the same Wan ip

  I'm trying to help a client to remove an extra router on their network.  It lies between them and the outside world.  The customer has a routed IP address block.  I want to do is move the old router on the new router wan and always keep the old ips outside for the nat/passage in.  Is this possible to do?

  Sage

  Hello

  I understand your topology for the following:

  ISP (i-net)---10.1.1.2/30 WAN (router) LAN LAN (RV042G) 10.10.10.1/29---10.10.10.2/29WAN... users... when both routers are in gateway mode)

  If this is the correct configuration you write that you do not need the first router. And if the network is already running in this way, it means that the rules of port forwarding for users are already created on both routers. What you need to do is just remove the first router and configure the WAN on RV042G port with IP 10.1.1.2

  You mention a VLAN 155 on the WAN side. RV042G has no option to specify the VLAN on the WAN port.

  Also, make sure that the ISP doesn't have any port as security to connect only to the MAC address of the router first.

  Kind regards

  Bismuth

• Several DMVPN Instances on the same WAN Interface

  Hi people,

  Is it possible to run several Instances of DMVPN on one WAN Interface? We can for example configure 3 Tunnels on a router using a same Interface WAN but running Instances separated from EIGRP for each Tunnel? Kindly let me know, Alioune

  Hi Martin,

  Yes, you can create DMVPN as you say with a WAN interface it's possible... you can have several interfaces tunnel pointed a WAN interface as the source interface, which is located in a public area... with different public ip as destination tunnel...

  Tunnel1 interface

  Description * A - VPN Tunnel *.

  bandwidth 100000

  IP vrf forwarding Red

  IP 10.0.252.2 255.255.255.252

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP mtu 1500

  load-interval 60

  source of tunnel GigabitEthernet0/0 (WAN Interface)

  tunnel destination 1.1.1.1

  protection of ipsec profile dmvpn tunnel

  !

  Tunnel1 interface

  Description * B - VPN Tunnel *.

  bandwidth 100000

  IP vrf forwarding Red

  IP 10.0.252.5 255.255.255.252

  no ip redirection

  no ip unreachable

  no ip proxy-arp

  IP mtu 1500

  load-interval 60

  source of tunnel GigabitEthernet0/0 (WAN Interface)

  tunnel destination 2.1.1.1

  protection of ipsec profile dmvpn tunnel

  !

  like the above... example...

  Please rate if the information provided is useful!

• Several VLANS, 2 WAN - balancing load, Failover, and NAT - Oh my

  I am bashing my head here to try to understand something that is really not as hard as I do must in my opinion.

  I have 3 VLAN (router on a stick configuration) and WAN 2 interfaces on an single router.

  VLAN1-> ISPS1

  VLAN2, VLAN3-> ISP2

  How can I set this up so that VLAN1 uses isps1 as the primary internet connection?

  How can I set this up so that VLAN2 and VLAN3 use ISP2 as their primary internet connection?

  How can I configure it so that VLAN1 will use ISP2 if isps1 fails?

  How can I set this up so that VLAN2, VLAN3 uses isps1 if ISP2 fails?

  I came across problems before with problems due to NAT - when you try to use applets IP SLA and event to simply update the commands route map.  Has not horribly.  So I think I'll send this to the community because I am at a loss and I need to have another set of eyes look at that - if its even something possible using only a single router.

  Hello

  Here's a way you can do:

  VL1_TRAFFIC extended IP access list

  ip permit 192.168.1.0 0.0.0.255 any

  VL23_TRAFFIC extended IP access list

  permit ip 192.168.2.0 0.0.0.255 any

  ip licensing 192.168.3.0 0.0.0.255 any

  ALS IP 1

  8.8.8.8 ICMP echo source s1/0 interface

  frequency 4

  Timeout 2000

  ALS IP 23

  ICMP-echo 8.8.8.8 source s1/1 interface

  frequency 4

  Timeout 2000

  Annex to sla IP 1 start now lives forever

  calendar of sla IP 23 now start life forever

  track 1 ip sla 1

  follow the 23 23 ip sla

  (1) vLan 1---> isps1 (primary), ISP2 (secondary)

  VL1_TRAFFIC allowed 10 route map

  corresponds to the IP VL1_ACL

  set ip x.x.x.x jump following check accessibility track 1 # next hop isps1

  set ip next-hop x.x.x.x # ISP2 next hop

  interface f0/0.1

  NAT IP in

  route VL1_TRAFFIC card intellectual property policy

  (2) vLan 2.3---> ISP2 (primary), isps1 (secondary)

  VL1_TRAFFIC allowed 10 route map

  corresponds to the IP VL23_ACL

  track check accessibility ip x.x.x.x next 23 value next hop #ISP2 hop

  set ip next-hop x.x.x.x # next hop isps1

  interface f0/0.2

  NAT IP in

  route VL23_TRAFFIC card intellectual property policy

  interface f/0.3

  NAT IP in

  route VL23_TRAFFIC card intellectual property policy

  (3) the overload of NAT:

  NAT_VL1 allowed 10 route map

  corresponds to the IP VL1_TRAFFIC

  football game interface s1/0

  NAT_VL23 allowed 10 route map

  corresponds to the IP VL23_TRAFFIC

  match s1/1 interface

  IP nat inside source map route NAT_VL1 interface s1/0 #ISP1

  IP nat inside source map route NAT_VL23 interface s1/1 #ISP2

  Kind regards.

  Alain

  Remember messages useful rate.

• How to treat several Photos with removal of Haze Auto

  Win7 64 bit

  Photoshop Elements 14

  Hello:

  How to treat several photos with removal of haze self at the same time? And how can I process several photos with auto shake reduction at the same time?

  If this can be done with actions, is there an action that can be downloaded to achieve?

  Thank you

  r398tow wrote:

  Win7 64 bit

  Photoshop Elements 14

  Hello:

  How to treat several photos with removal of haze self at the same time? And how can I process several photos with auto shake reduction at the same time?

  If this can be done with actions, is there an action that can be downloaded to achieve?

  Thank you

  Unfortunately, you can only batch with commands in the option "treat multiple files" of the editor or the 'Export' one in the Organizer. Action would be able to combine several orders for a single file, but do not use the command given on a lot. You would need a script for this.

  The two new orders to 14 elements (haze removal and shake reduction) can be very effective, but they can also produce strange artifacts... Their use in the batch may be undesirable.

  I recommend the following solution to improve lots of files needing to increase the local contrast:

  If you work with raw files, open a small batch of files from the Organizer in the ACR module. Use the cursor to 'clarity' to all files in the batch and add some sharpness.

  If you work with JPEG files, use the editor and choose "open in camera raw" option for your batch chosen files from the file.

  Who should provide a good improvement to most of your files. You can use two new orders than in the pictures with the specific defects:

  -shake (common with telephoto lenses) removal

  -mist removal (not only haze, but images softened with "flare")

• Questions about vCSHB 6.5.1 (LAN or WAN and physical vs. virtual secondary server)

  Hello

  I have a few questions about vCSHB 6.5.1:

  1) there are two sets of installation guides: one for secondary physical server and a secondary server.

  What are the main differences between these two scenarios?

  (2) for vCSHB, there are two deployment options: LAN and WAN

  2 (a) which option is most common?

  2 (b) If an option (for example, LAN) works in an environment, can I assume that the other would work as well?
  And what a difference these two options?

  (3) is vCSHB backward compatible? VCSHB 6.5.1 works in an environment where an earlier version (for example vCSHB 6.4) works?

  (4) what version of vCSHB (e.g. vCSHB 6.5 or 6.4 and 6.3) is widely deployed today?

  Thank you.

  (1) there should be nominal differences - what is different is discussed the virtual network set up against the physical network implemented

  2 (a), in my experience LAN configuration is more common because it over a high availability solution oppesed to DR.

  2 (b) not necessarily, you should make sure that the appropriate ports are open

  (3) I think it is but you have to bring everything up to a compatible version as a best practice

  (4) I'd go with the latest version as it has been out for a few weeks-

• Several subnets on a WAN interface

  We have a WAN connection that Comcast provides us with two different subnets. Currently, the interface is programmed with just the static IP address.

  How can I enter the subnet on which has our static range of IP addresses? I saw this article, but I don't know if that's what I have to do.

  Help!

  Yes, you have found the right article.

• Multiple WAN + several VLAN = hair loss

  Hello world

  We have a block of IP addresses of our ISP and I am using one for a network of comments, but I can not understand how to configure.

  X 2 (ending with 150 WAN IP address) should feed WAN X 0 (VLAN 1), and

  X 2 (ending with 151 WAN IP address) should feed WAN X 0: V2 (VLAN 2).

  I have already created the sous-interface side LAN and VLAN works very well internally.  I just need to know what NAT rules (or rules of firewall or sorcerers, etc.), I need to enter to the above plan work.

  Thank you!

  Hello

  Policy NAT below should help you accomplish what plan to do:

  Original source: X 0 subnet
  Translated source: X 2 (IP WAN ending by 150)
  Original destination: all
  Translated destination: Original
  Original service: no
  Translation service: Original
  The source Interface: X 0
  Destination interface: X 1

  Original source: X 0: subnet V2
  Translated source: X 2 (IP WAN ending with 151)
  Original destination: all
  Translated destination: Original
  Original service: no
  Translation service: Original
  The source Interface: X 0: V2
  Destination interface: X 1

  #IWork4Dell