Satellite P205D-S7802 - DVD player shows that D: and the CD shows that C

Similar Questions

• Satellite L30 VISTA - DVD player does not empty and clean recorded DVD

  DVD - RW 4 x discs ignored. When I try to 'burn' of ULead DVD Movie Factory or play a previously "burned" DVD made on my old model Qosmio, the DVD tray opens (with the disk in it) and with the message "Please insert disc". If the tray closes with the same disc always in it, it does exactly the same thing again.

  Product Commercilly DVD is most recognized and played. This problem exists since the laptop was purchased. Would appreciate any help.

  If this problem existed on the first day, why did you wait so long and not tried to resolve as soon as possible?

  I recommend you to install the Nero trial version and check the functionality of engraving. Try please to create CDs or DVDs burning data or maybe some movies on DVD. Test these media. If you report about the same so I can believe that there is a serious problem.

  One last thing. Try to start with recovery media. Please let me know if the recovery procedure starts correctly.

• Satellite P205D-S7802 - need help with Wi - Fi

  I have a Toshiba Satellite P205D-S7802. I had windows Vista on it, but the time has come to reformat.

  I tried to do just the recovery disk to reset it back as long as the factory, but after using the disk a discovered I do not know where disc 2 is therefore due entirely reinstal bootleg windows xp pro.
  But now I can't figure out how to get my wireless connection to connect to it. I don't even see the wireless icon or the available tab.

  Is there a driver I need to install or what?
  Thank you for your help

  Hey,.

  Normally after the installation of the Windows operating system with a Microsoft disc, you need to install all the drivers for the hardware. So do you have yellow exclamation mark in Device Manager?

  I think that you need to install the WLAN driver too. You can download all the drivers page Toshiba or Toshiba WLAN to WLAN card Portal: http://aps2.toshiba-tro.de/wlan/

• Satellite L455 - Burned DVD plays in slow motion in the dvd player

  Hello

  I have a Satellite L455.

  I got burned a DVD with Nero 7 premium, but when I play in the dvd player, it works idle all the time. Other movies are played normally (so the problem is not the dvd player phillips), this only happens with the ones I burned in my new Toshiba laptop.

  I have tried to burn all kinds of speed (x 8, 6 and 3), but the problem has not been resolved.

  Can someone tell what should I do?

  Thank you.

  Hello

  You tested this external DVD drive?
  I recommend to check the options of Nero again and maybe, you should also use an other DVDs from different manufacturers.

  My DVD player didn t play DVD's serious too, I changed the manufacturer of DVDs and then the DVD that can be read by a DVD player

• How to operate the DVD player so that I can run DRIVER RECOVERY DVD from HP?

  Separated from this thread.

  Hello

  Thanks for the reply, I clicked on the link and it shows windows...

  Here I can not open the widows of anywhere.

  How to operate the DVD player so that I can run DRIVER RECOVERY DVD from HP

  MINE IS A VERSION OF COMPAQ PRESARIO HOME ON WINDOWS VISTA

  He always goes to startup repair

  then he said not being able to correct automatically

  Under system recovery option what can I do?

  I don't want to go back to the point of origin of the memory (factory settings)

  Thank you

  Patrick

  Hello

  Have you tried using SafeMode w/command invites to perform a system restore?

  1. Press the power button to turn on the computer.
  2. In the first screen, press the f8 key repeatedly every half second until what the Windows Advanced Startup Options screen displays.
     
  3. Press the arrow key down until Safe Mode with command prompt is selected, and then press ENTER. Wait while the Windows Load system files. The Windows log on screen is displayed.
  4. At the command prompt, type rstrui.exe, and then press ENTER. Wait a few moments for the system to open restore window.
  5. Follow the on-screen instructions to perform a system restore.

  You have now returned the computer to a previous restore point using Mode safe mode with command prompt.

  Using Microsoft System Restore (Windows Vista)

  http://h10025.www1.HP.com/ewfrf/wc/document?cc=us&LC=en&DLC=en&docName=c00807369

  You also have the option to create a backup of your files when you perform a recovery

  http://h10025.www1.HP.com/ewfrf/wc/document?cc=us&DLC=en&docName=c00809678&LC=en&product=18703#n405

• I bought 10 items on the disk and now need to install it on a new computer that lacks a dvd player. Download it from the Adobe site?

  I bought 10 items on the disk and now need to install it on a new computer that lacks a dvd player. Download it from the Adobe site?

  Download Photoshop Elements | 10, 12, 14, 11, 13

• I have a laptop SVF1521P2EB model. Since I put victory 8.1 the dvd player has falt error 19-the register

  I have a laptop SVF1521P2EB model. Since I put victory 8.1 (I Think) the dvd player does not work. The pilot is there and looks ok, but reports the error 19 which says that there is an error in the registry. Any help to fix it please

  Cheers, will have a goat that

• How can I fix my dvd player so it will play the DVD

  I ordered a new DVD player on amazon, he came straight from China. Now it will not read the dvd. and there is no region tab change the region in the dvd drive properties.

  Windows Media Player cannot play the DVD because the disc prohibits playback in your region of the world. You must obtain a disc that is intended for your geographic region.

  Hello

  Check with the support of creating DVDs, their online documentation and drivers.
  Troubleshooting and ask questions in the forums about known problems. Don check
  for Windows 10 compatibility.

  Click with the right button on the Start button CD/DVD Player - Device Manager - double click
  the player - driver tab - click on Uninstall - then OK - reboot the computer for
  reload the driver. If no help go back and try to update driver, and then click OK.

  More troubleshooting.

  1. control - troubleshooting - hardware and audio Panel - configuration of a device.

  See if this resolution of the problems of aid.

  2 Panel - Device Manager - DVD-CD drivers - right click on the disk -
  Driver tab - uninstall the drive - and then restart the computer

  3 see if this helps:

  FIX: DVD drive not detected in Windows 8/10
  http://www.intowindows.com/fix-DVD-drive-not-detected-in-Windows-8/

  =====================

  If necessary we will test the CD/DVD player to see if it works at all:

  Try this to see if the drive is viable at all (you will need to make of these on)
  another computer since your willingness not to not start - XP, Vista, 7, 8/8.1 or 10
  (or even under Linux is not serious). You can also try to start with
  another drive in Windows - any OS but do not use it to try to repairs
  unless it's absolutely the same version of Windows on your system - just
  start to see if the drive works. You can even make a boot Windows 10 DVD
  disk by running the creation of Windows Media tool (on any computer)-

  Tool for creating Windows Media (make 32 or 64 the two same disk as the operating system
  the version you are using.
  http://www.Microsoft.com/en-us/software-download/Windows10

  / Settings (BIOS/CMOS) often F2 then watch the display as launch you - set
  the order of boot on CD/DVD first. Don't forget to when.

  Or ry boot from a Linux boot disk.

  If the player does not start to these then there no or there is other equipment
  problems that affect it. However, even it doesn't start that does not mean there is
  other functions not possible some hardware problems affect the reader.

  Trinity Rescue Kit - download on top right of the page
  http://trinityhome.org/home/index.php?wpid=1&front_id=12

  CD of Hirem boot is another good choice
  http://www.hirensbootcd.NET/Download.html
  http://www.hirensbootcd.NET/CD-contents/138-HBCD-111.html

  System Rescue CD
  http://SysRescCd.org/Main_Page

  Scan a Windows PC for viruses from a Ubuntu Live CD
  http://www.howtogeek.com/HOWTO/14434/scan-a-Windows-PC-for-viruses-from-a-Ubuntu-Live-CD/

  Use Ubuntu Live CD to backup files from your Windows computer dead
  http://www.howtogeek.com/HOWTO/Windows-Vista/use-Ubuntu-Live-CD-to-backup-files-from-your-dead-Windows-computer

  Check the wiring of course that nothing is not loose.

  I hope this helps.
  --------------------------------------------------------------------------------------------
  Rob Brown - Microsoft MVP<- profile="" -="" windows="" experience :="" bicycle="" -="" mark="" twain="" said="" it="">

• DVD player does not appear error - the driver may be corrupted or missing. Code 39, fix the driver installation fails, virtual drives don't work - same results if the material under tension

  Original title: drive does not appear, difficulty he pilot installation fails, virtual drives don't work - same results if the material under tension

  A few weeks ago, as my two DVD players (the two Samsung Lightscribe SH-S223Q of) disappeared after a repair installed, I did for the other problems (not sure if it was directly after installation because I don't notice it right away, but it was no doubt). In Device Manager, it gives the message:

  "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) »

  I tried the Microsoft Fix It tool (Mats_Run.dvd.exe) that detects the problem and says "Install device driver" in a popup, but then he says "software device driver failed to installed. At the end it says under the issue, the "CD/DVD drive is not detected" and the status of Fix 'not set '. Note that, when I boot from another hard drive (with Vista 64 on it installed from the same DVD, just a new installation) disks appear very well. Also I can boot from the drive as well.

  I can't do a repair installation, since it must initiate Windows, and I can't load the disc. I tried to update my BIOS but that has no effect.

  Recently I actually moved this hard drive to another one, with another brand of hard drive and all the rest. Just like before, if I boot from another hard drive (this one with Windows 7), the drive unit-a Optiarc AD-7230 s - looks and works, and I can also boot from the drive at startup. But since the drive hard as I want to use, the drive does not appear. Fix it, etc. Device Manager gives the same messages as before.

  I tried virtual drives - Daemon Tools Lite and Virtual Clonedrive. When I try to add virtual devices to help, nothing happens. The new drive will be displayed in the Manager of devices, but with the same error Code 39 as the real drive.

  What are my options at this point? How can I get the drive to appear or to fix my copy of Windows?

  I could solve this problem. I started in Ubuntu and deleted the existing cdrom.sys, cdrom.inf etc. files (as in Windows, they were protected and I couldn't delete them), then I copied the files from another installation of Vista I had on another hard drive. After having done that, I updated the drivers in device, disabled/enabled readers and readers management that presented themselves.

• I try to install my photoshop material... but I have not a dvd player... is any way for me to do this without a dvd player?  I already bought the software in a form of DVD

  I try to install my photoshop material... but I have not a dvd player... is any way for me to do this without a dvd player?  I already bought the software in a form of DVD

  Download Photoshop Elements products | 10, 11, 12, 13

  Download the CS6 products

  Mylenium

• I updated my windows media player 10 or 11, and the information album site is messed up. It won't change my album information. Please fix the site.

  I updated my windows media player 10 or 11, and the information album site is messed up. It won't change my album information. Please fix the site.

  Hello

  What operating system do you use?

  Windows vista comes with Windows Media Player 11.

  Method 1: I you suggested to clear the cache of the album and then try to update the album information.

  Follow the path to clear the cache of the album

  C:\Users\\AppData\Local\Microsoft\Media Player\Art Cache\Delete the localLMS

  For more information, you can consult the following link:
  http://Windows.Microsoft.com/en-us/Windows7/add-or-change-album-art-in-Windows-Media-Player

  Method 2: Method 2: you cannot view, add, or delete items in the library of Windows Media Player 11
  http://support.Microsoft.com/kb/925718

• Satellite P205D-S7802: disk problem CD/DVD; driver damaged or missing

  Hello

  DVD unit has not recognized by the operating system.
  When I open my computer the only display unit is C, there is no unit D.

  Then I go to the Device Manager to check it out, and I noticed that the DVD unit has problems, then I open the properties, and the error message is:
  'HL-DT-ST DVD RAM GSAT20N ATA DEVICE.
  Windows cannot load the driver for this hardware device. The driver may be corrupted or missing.

  First I thought it was a hardware problem, but I introduced the disc of windows vista at startup and the unit read it very well. Then I choose driver update of Device Manager and update told me that the best driver is already installed for the device.

  I tried to replace the files .sys and .info for CD-ROMs, but nothing is happening.
  What is happening, please help, is urgent I need to use my dvd device.

  Kind regards.

  Try this:

  Remove the drive from the Device Manager list CD/DVD
  access the registry and delete the Upperfilters and Lowerfilters completely from the following registry key values:
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class {4D36E965-E325-11CE-BFC1-08002BE10318}

  This is described here in the article MS knowledge base:
  http://support.Microsoft.com/kb/270008/en-us

  Check it out!

• Satellite Pro U300 - DVD Player error

  Hello
  I had not used my DVD player for a long time, and when I tried to use it again the other day that he has stopped working. Where to insert the DVD and the DVD player provided Toshiba starts a message pops up saying
  "Impossible for the release of the video on an external device. "Please change your display keys of the device by pressing the Fn + F5 after the end of the application.

  I did what he said and further and have made sure the computer does not recognize somehow, another device connected to my laptop. All that shows is the LCD screen of the laptop and nothing more. No clue as to how can I fix? I don't have an external display at the moment as im at Uni. so I can't plug a hook to the top and see if it works like that and then properly close. Any other suggestions? Would be great,

  Thank you

  George J.

  Hello

  This problem is known to me. I got it with my Satellite P200. I was not able to solve this problem.

  I just deleted a Toshiba DVD drive and now I use VLC media player. Download the latest version. The player is just great.

• Satellite P300 - Toshiba DVD player does not play DVD

  "I have a Toshiba Satellite P300 1Ci and when I play a DVD with a Toshiba DVD player, I get an error saying:" kan niet naar een extern uitvoeren expensive video. Page External uitgang nagaoui u would beeindigd toepassing van El' or in my best English: cannot run the video to an external device. Check your configuration of the external port after you have completed this process.

  can someone help me?

  Hello

  Want to watch a DVD on the external monitor? Or can you explain what you mean with external device?
  Maybe the application should be reinstalled. You can download it on the Toshiba site.

  I don t use a Toshiba DVD player so I think that I can help you, but I use VLC media player to watch DVD s. It of a small video player that can play most audio and video files. It s really nice tool and freeware. You should try it too! ;)

• Satellite A500 - video/dvd player is not compatible with Windows 10

  After having recently updated of my laptop for windows 10 I discovered that the dvd player does not work. A message is displayed informing that the player is not compatible with this version of windows. A scan using Norton suggests dvd will not work because it needs to be configured.

  Does anyone else have this problem?

  Obviously, Toshiba DVD playback application that is preinstalled on this Satellite A500 model is not compatible with the system Windows 10.

  In this case this software will not properly work after the upgrade to win 10 and I guess you have to remove the system Win 10.

  Unfortunately, the Satellite A500 is not listed as Win 10 portable computers and so I don't think you will get an update to this software for DVD playback.

  Here is a list of models supported for upgrading to Windows 10
  http://win10upgrade.Toshiba.com/swup...SPX?region=TEG