Satellite PRO P200 (PSPB7E): LAN PCI network resources - conflict problem

Similar Questions

• Satellite Pro P200 PSPB7E - I need some drivers XP

  Hello world

  First of all, I would like to say that this forum is so great, because after fighting for a week trying to install XP, I had finally finished it, however now comes part 2 of the problem :(

  Before I installed XP on my system I did so that I have all the drivers, I went on the Toshiba site and downloaded all the XP drivers. When responsible got XP I could see there was a lot of drivers uninstalled in Device Manager, so I installed them. However, a few of them remain and I don't know what to do as I downloaded all from the Web from Toshiba site.

  I myself remember before I installed the drivers there are 2 required audio and one of them installed, I also tried to install the "Display driver" but I can't because its not letting me run the actual setup file it says the file www.LATICRETE.com being created is more than 88 characters: s never seen this error before.

  So in all I have 3 missing drivers, they are:

  Audio device on High Definition Bus Audio - but my sound works
  PCI controller memory, and
  Video controller (VGA Compatible)

  Any ideas of what I could do? Thank you

  Yes, the forum is really helpful!
  I m regular guest here. I have 3 laptops and I would like to share my knowledge with other users

  * Only for note; *
  All THE XP drivers are available for this laptop Satellite Pro P200 PSPB7E on the European driver Toshiba page!

  In addition, if you check the European disc of Toshiba page you would see that there is a special BIOS update for Win XP!
  This means that you must update the BIOS if you want to use XP on this laptop!

  Regarding your question of pilot;
  > Audio device on High Definition Bus - Audio but my sound works

  I also have this yellow exclamation point. This is normal with Win XP, but if you want to check out these tips:
  You must first install the MS patches: KB835221and KB888111.
  Remove the device on High Definition Audio Bus Audio from the Device Manager, then restart the computer again.
  You may need to reinstall the audio driver.

  > The video controller (VGA Compatible)
  This unit requires a graphics card driver
  Check if you can use the XP driver out for one of these models:
  Equium A200 PSAE8E
  PSAENE satellite A210
  Equium P200 PSPB8E
  Satellite A200 PSAE6E
  Satellite A210 PSAELE
  PSPB6E Satellie P200
  Satellite P200 PSPBQE
  Satellite Pro P200 PSPB7E
  Satellite Pro A200 PSAE7E

  > PCI memory controller
  You must install the Texas Instruments Flash Media Driver

  Good bye

• Satellite Pro P200 (PSPB7E) - where to find the new display drivers?

  Laptop bought in July 2007, the Windows Vista Business operating system.
  Vista windows update immediately so don't know not if the following problem was there before I updated.

  When put in a slideshow for all images almost immediately a blue screen appears and the problem message I receive is "problem caused by the ATI graphics card.
  Have never been able to sort out as when I contacted ATI they told me to contact Toshiba.

  Can anyone help? Where can I get the proper drivers and how to find them on the laptop which is my current driver?
  Chris

  Hello

  You can download all the drivers and tools for your laptop on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  Before installing the new version, you must delete the old class first, and then restart the laptop.

  If you go to the graph properties, you can check what display driver you have right now.

  Moreover, you have what Service Pack installed for Vista?

  Welcome them

• Can I downgrade my Satellite Pro P200 for Windows XP?

  Hello

  I bought my Satellite Pro P200 (PSPB7E) a week ago and I love it. I have an unused XP license, so I would like to downgrade.

  Is this problem? I don't see xp for a Chicony webcam drivers or the HD-DVD player.
  I'd really appreciate some feedback. There must be someone out there who has tried to do.

  Thank you in advance!

  Hello

  Of course you can downgrade the satellite Pro P200 for Windows XP.

  When installing XP, you need to install the Intel Storage Manager. It is a SATA driver that is needed to activate the HARD disk.

  Regarding the webcam driver.
  I checked the page European driver of Toshiba and the Chicony webcam driver is certainly available.

  The HD DVD driver is not necessary because the Windows XP must use an own ODD driver.

  See you soon

• Satellite Pro P200: network connectivity is not stable

  I have a Satellite Pro P200, which was downgraded from Vista to XP Pro SP3 corporate.

  I use a sensitive enough network application that will crash when network connectivity is lost.
  This application has been blocking a lot since I downgraded to XP, so I tried to run a continuous ping that gave rise to many messages Request Timed Out (the maximum number of attempts where I actually had ongoing responses was about 30 but is usually much less).

  I use the driver downloaded from the Support from Toshiba site (Realtek RTL8139/810 x Family Fast Ethernet Nic - v5.664.205.2007), wireless network works fine, tried to connect to the network using a cable and a port different without change, and using a different laptop with the same cable and port works fine.

  The yellow exclamation mark in Device Manager is a memory PCI controller which I believe is for the Intel Turbo Memory, because it is not compatible with Windows XP.

  Any ideas what could be the cause.
  I tried reinstalling the driver several times without success, it is likely to be software partners or could it be a hardware failure?

  I think it's related software and troublemaker is SP3. Test it with SP2 only and it will work perfectly. Friend of mine noticed permanent data LAN transfer interruptions after installing SP3. Remove everything works well again.

• Satellite Pro P200 with WXP - two components without driver

  I installed XP Pro on my Satellite Pro P200 15W and I installed all the drivers on the driver download page, but I have still two components without driver: these devices, I don't know what types of devices are, because it seems that this medication works very well. The features are:

  Memory (Controladora de Memoria PCI) PCI controller
  Unknown device (unknown device)

  I aso installed upgrading Bios WIN5.00, but both devices still does not.

  Any idea?

  Thank you everyone

  The * PCI controller memory * Intel Turbo Memory is called a chip Flash cache logic Intel (Robson device).
  It s a new technology designed to support the new features of Vista.

  There is not driver for it for Windows XP because XP doesn t supports the function of cache, it is supported by Vista.

  The other unknown device could be everything; You may need to verify that the devices do not work. LAN, WLan, etc...

• No software DVD player with my new Satellite Pro P200

  Just bought a new Satellite Pro P200 and, to my surprise and dismay, it has software player DVD No. inside? I downloaded the DVD drive on the official download here, but Vista abandoned the facility saying that I can not install the application. Have you tried to configure it as a Admin, but the same message is given running.

  Suggestions as to how I can get the software to run movies DVD on the new laptop computer would be most appreciated.

  The laptop is model is PSPB7E, it has Vista Business installed and has a HD-DVD drive installed.

  Would apprecate a response early to what I already plan to return this item, demanding a full refund since it seems that it does NOT use a software which SHOULD run (IE. Compatible versions of some software XP will simply not installed because Vista blocks!).

  Kamshot - discouraged by the new culture of 'Vista '!

  Hi Kam

  As far as I know every Toshiba laptop comes with pre-installed software allows you to watch DVD movies. It is a part of the standard installation and the application is called WinDVD.

  According to the specifications of the laptop, your laptop has no HD DVD player, just DVD-Super Multi (+ r DL). Because of this there is no HD DVD player.

  > Would apprecate a early response to what I already plan to return this item and requesting a full refund because it > seems that it does NOT use a software which SHOULD run

  No comments for this

• No sound in Satellite Pro P200 with XP

  Hi all.

  I have a Toshiba Satellite Pro P200 with Windows Vista preinstalled. I removed Vista and installed Windows XP with Service Pack 2, due to the incompabilités with some software I need. Almost all of the necessary drivers for XP (even a downgrade to BIOS) was downloaded and installed from Support from Toshiba web page. But there are still two devices that I can not install. At the start of my laptop it always detect "* Microsoft UAA bus driver for high definition audio *" and "* controller memory PCI - Chip for logical Cache Flash in Intel (r) *" as new hardware and they appear marked in yellow in the Device Manager list.

  I installed the last bus Microsoft UAA for high definition audio driver for XP from Toshiba and Realtek too... a lot of time and in different ways... Previously I installed the High Definition Audio Driver Package - KB888111 from Microsoft. But I still have no sound.

  PCI memory controller - Intel(r) Flash Cache Logic Chip: the same... tried the drivers the most recent Toshiba one Intel too. Toshiba technical support told me that this unit is ready to run on Vista and have suggested me to try with Robson drivers for Vista Support from Toshiba's web page, but that didn't work either.

  I googled a lot, searched this forum and called technical support, as I said, but I've not found a way to solve these problems. Really, I can't believe I bought a laptop that only works with Windows Vista, I resist assume this idea, so I continue to try and try to make it work properly with the operating system that I need and I have chosen freely.

  Any idea?

  Thanks in advance.

  Hello

  > I installed the last bus Microsoft UAA for high definition audio driver for XP from Toshiba and Realtek too... a lot of time and in different ways... Previously I installed the High Definition Audio Driver Package - KB888111 from Microsoft. But I still have no sound.

  You're on right way boyfriend, you must also install another patch MS; KB835221
  So finally the KB888111 and KB835221 must be installed before you will follow with the audio driver installation.

  Check this thread:
  http://forums.computers.Toshiba-Europe.com/forums//thread.jspa?MessageID=113124

  > PCI memory controller - Intel(r) Flash Cache Logic Chip: the same... tried the drivers the most recent Toshiba one Intel too. Toshiba technical support told me that this unit is ready to run on Vista and have suggested me to try with Robson drivers for Vista Support from Toshiba's web page, but that didn't work either.

  The problem is that this unit only works in Vista.
  The controller memory PCI is that intel Turbo Memory, also called Intel Flash cache logic chip also called device Robson.
  It's quite new technology designed to support the new features of Vista.
  There is not driver for it for Windows XP because XP doesn t supports the function of cache, it is supported by Vista.

  Hope I could help you

• White screen after the Satellite Pro P200 display driver update

  I installed the latest display driver ATI Mobility Radeon HD2600 (8.432, on the site of Toshiba through Tempo) on my Satellite Pro P200 yesterday. Reboot, everything seems good as much as the screen "Please wait...". "Windows Vista professional, but instead of showing the page of connection I get an empty screen (with a mouse cursor that moves around as usual). All I can do at this point is to be able to, and I'm running out of ideas on how to move forward.

  Things I've tried:
  # start in safe mode, the video resolution or last known good configuration, result the same screen empty.
  # connect to the system using remote desktop (to disable the driver) is not possible because the system has not yet loaded the network drivers.
  # I can't go back to a restore point because Vista can't find (I did a manual after you install updates windows over a couple of days).
  I can run a system command line options of recovery and prefer to use it to disable the driver + if + I knew how before the use of the more radical options.

  A search on the web (http://www.google.co.uk/search?q=ati+catalyst+vista+blank+screen&hl=en&sa= N) reveals that this has happened on a wide range of laptops with
  previous versions of the driver, but none of the links I've looked at to give a solution which does not exist for me.

  I agree with Hairyfool, you who should solve problems using an external display. If no image appears, then something with the material might be.

  Please give some information about your situation...

  See you soon

• Satellite Pro P200: Cannot install Server 2003 - parity memory error

  I have a Satellite Pro P200 and to the work required to install Windows 2003 server on it, but all I get is an error message:

  -Hardware malfunction

  Call your provider of support material

  NMI: Parity check / memory parity error

  -The system is shut down

  I checked the memory and everything seems OK. Vista runs very well on it, and all memory is recognized. I tried different flavors of Server 2003, although all I need is standard edition. Anyone who has met this problem, or someone has any suspicion as to how I can get it operational.

  So, how tested the RAM? With Memtest? Or Prime95?

  I read in many forums that people work servers (no laptop...) SERVERS) that correctly work 1 year with ECC memory, then windows 2003 server gives the same error message you have.

  I mean if Vista works flawlessly and you checked as you say the RAM while there could be a mismatch which must not be for lack of toshibas.
  Maybe you should try a linux ubuntu server edition, which works great on almost * ALL * systems, even on systems with faulty CPU/memory (Ok, ok, not 100%, but it works, I got this case :))

  So, maybe you can try to exchange the RAM, but if you're still the same error then ask microsoft or try another P200, if they are available.

  Sorry dude, but I Don t have a lot of ideas in your situation :/

  Welcome them

• Satellite Pro P200-150 - where to find drivers for Win 7

  I have a PC Satellite Pro P200-150 with Vista Business bought in 10/2007.
  I want to change the hard drive 250 GB, I want to take this opportunity to pass on Windows 7 Home Premium Version.
  I'll buy a load of DVD.

  My question is: How can I get the drivers, but especially utilities Toshiba?
  On sites that I've explored I find driver downloads but no public services.

  Thank you for your response.

  Hello

  Check the Satellite Pro P200 driver download area.
  You will find all the drivers Win 7.

  Note: the P200 is a little older series you must choose in the Archive of the Type of product to get the drivers

• 2nd hard drive in Satellite Pro P200

  Hello world

  I have a Satellite Pro P200.
  Anyone know where I can get an advance and a shopping cart to install a 2nd hard drive?

  As far as I know your laptop can be improved with the second HARD disk if the SATA connector is available.
  When you remove the HARD drive to the second HDD can you see it or not?

  I have the Satellite P200D with place for second HARD drive, but there is no connector HDD SATA upgrade is not possible.

• Satellite Pro P200 - 17 c: Win XP won't load - installation of the SATA driver

  Hello

  I have a satellite pro p200 - 17 c I've had good years, allways worked without any problem.

  Last week when I booted the laptop, windows won't load and I find myself safe mode selection screen. No options whatsoever me to windows loading, I tried F8 and still nothing.

  I tried the restore cd that reimagee the drive but I get the same thing, I tried a new hard drive, once again the same.

  But if I try to load windows from an OEM to install that software does not because it is a sata drive and there is no floppy drive. I have an external floppy drive I use, but it is not known now.

  Any ideas or suggestions?

  Hello

  Go to BIOS and set it to default settings.

  In this case the SATA mode must be on AHCI. In this case the SATA drivers are required to install the Windows operating system. But as much as I know that Windows 7 already contains the SATA drivers if usually you don t had to add SATA drivers while OS installation the installation program.

  However, here is a nice HowTo document that helps you add SATA drivers for Win XP installation disc.

  + How to integrate a SATA AHCI driver into a Windows XP Setup CD.
  http://APS2.toshiba-tro.de/KB0/TSB85017Z0000R01.htm

  + How to integrate the AHCI driver during the installation of Windows XP.
  http://APS2.toshiba-tro.de/KB0/HTD9401AN0000R01.htm

• SSD upgrade for Satellite Pro P200 (PSPB7A-01000J) - possible?

  Hello world

  I had a Satellite Pro P200 for 3 years and more. It came with Vista Business pre-installed, but I have successfully installed Windows 7 a few months ago.

  A few months ago, I replaced the C drive in my office with a Solid State Drive and now he sings - program start and loading of the system is much faster than before.

  Now I'm wondering if the SSD upgrade even could be done to my trusty P200 and if yes, what brand/model of SSD could be better. It should be 128 GB or 256 GB maybe.

  Anyone else been in this way? The results? Pitfalls?

  All responses appreciated.

  Thank you.

  Greg.

  Hello

  I think that it should be possible.
  You must use a SATA SSD drive since the laptop supports the SATA controller.
  To be honest, I never tried to upgrade the laptop with a SSD but SSD is not very different from the HARD drive and normally should not be a problem.
  In some cases, an update of the firmware of SSD may be necessary but usually these firmware updates should be available on the SSD drive manufacturer support page.

• Failure of the BIOS - Satellite Pro P200 - 16 c

  I installed Windows 7 64 bit on a laptop Satellite Pro P200 today. I then tried flashing the BIOS through windows with program Flash BIOS on Toshiba driver download page. I used the program flash for Vista because none is available for Windows 7. The program started and took a backup of my old version of BIOS and then Flash the BIOS. Then after a while an error occurred saying that this operating system was not supported.

  Alright. I restarted the computer and he was going to access the BIOS to see if the new version was done to install or not. But I can't access the BIOS now since the TI of suddenly password protected. I tried Google known standard Phoenix BIOS passwords, but they do not work. Now I've mistyped the password if often the computer won't let me even start without entering a correct password.

  How can I reset the BIOS? Should I open the laptop and remove the CMOS battery? Which will work?

  Help, please...

  Hello

  You used not compatible BIOS and it seems that module ROM BIOS was not flashed properly.
  Unfortunately, there is nothing to do but to contact the ASP of Toshiba in your country,
  Guys could remove the password and can reflash the BIOS using a traditional disk BIOS version and the crisis.

  > How can I reset the BIOS? Should I open the laptop and remove the CMOS battery? Which will work?
  No, remove the CMOS battery would not help because as far as I know that the CMOS battery is not removable on laptops just ASP can clear the BIOS password.