Satellite S2400: "Block 1 BIOS is corrupted" Error Message at startup
Hello
my laptop S2400-103 does not start, instead it gives my the error message mentioned above and request a disk "interview."
How can I fix? I downloaded 2 updates of BIOS for this model, but they both require a Windows system running.
Thank you
Hans
Post edited by: hanzf
For this old Satellite notebook, you can download Win and TRAD BIOS update.
Here you can download the updated BIOS TRAD (traditional) version and it works using the floppy and has nothing to do with the Windows operating system.
I don't know if you can fix damaged BIOS, but you can try it.
Tags: Toshiba
Similar Questions
-
Satellite Pro M70: Update Bios - ROM size Error Message is incorrect
I downloaded the BIOS updated but a message "ROM size is incorrect" when I try to run the installer.
This, according to the web site, should be a simple process! I know I'm a beginner but.
I have a real struggle
Hello
I think you chose the wrong BIOS.
You should be careful with these updates because the bad BIOS and bad upgrade procedure can bring a lot of trouble with the laptop and the motherboard.Check all the details before you start any update
-
Pavilion DV7-6000 series. Error message at startup invalid product information
I didn't know that my motherboard was bad from the factory. On the first day, I was unable to do a full factory restore. I always send to HP. They sent me a motherboard and after installing it, I was able to do a full factory restore. It was amazing... However, I now have this error message at startup. Does that mean exactly?
When I go into the BIOS, information on the system is xxxxxxx. When I go to HP technical support. The product name, serial number and product number is yyyyyyyy. I know it's fake, why?
Please don't tell me I have to send it after all.
OK I won't tell you who, but you already know this is bad and you need to call HP. There is a special piece of software used for 'tattoo' Board of Directors. I have seen a few cases where they just give you a link to download and instructions on how make the 'tattoo '.
-
I had hard time to upgrade to 8.1 Windows, so I made an update of the bios, as recommended by the HP Web Site, but it failed, and now the laptop will not boot. It displays the error message "your computer must be repaired: \bcd, 0xc0000034... error code. "Additional info are available by pressing ESC, and I can't get into a black screen with options:
F1 system information
the F2 System Diagnostics
F9 boot device options
configuration of the BIOS F10
F11 system recovery
I've been to the bottom of all of these tracks, with no luck on continue. F10 shows me all the bios configuration screens and the version of the bios is F29, the version I tried to level to.
I tried to remove the big battery and pressing the start for a minute button - no joy.
I tried now Windows + B + start - no joy
I guess I'm trying to create a USB key with the BIOS on this subject, and this is where I am confused. The softpaq BIOS for this machine is sp66880.exe. I've got that on an USB fat32 with the label of volume HP_Tools, and I've got HP tools on the stick too. When I try to boot with the stick of pressing windows + b + start, the light on the USB flashes a lot, but in the end I get the message "the system bios recovery has failed. Could not open the bios image file. I have a feeling that I don't have the correct configuration on this USB key. I tried to run sp66880.exe on another computer, but he said that he will immediately Flash the bios, I really want to do (on my Toshiba laptop!).
I would be very happy any help you all can give me on how to create USB recovery key in the proper format. Thanks in advance.
Fixed!
It turns out that the update of the bios is really successful, but something in the hard disk boot files has been corrupted. I got a USB key recovery Windows 8 on another machine and finagle around having HP laptop reformat the hard disk to the original factory State. Fortunately, I made a very recent Macrium image until this most recent problem, so the next step is to restore this image. With the new c F29 bios, I hope that this beast will finally go to Windows 8.1.
-
Files missing or corrupt error message
Pavilion g4 with Windows 7
Try to open Microsoft Office library files, I get the following error message: "this program is unable to run because of missing or corrupted files. Contact the manufacturer of your computer. "Also, seen in the library, Microsoft Office files do not display their characteristic icons (Word, Excel, PowerPoint, etc.). All cultures view the Red page, icon. However, when I open the files of their respective programs, i.e. all first open MS Word and then open one of the files affected by the program, they open without difficulty. I would be grateful for views on the resolution of this problem.
By 'Library' you mean say Windows Explorer instead, or you want to say in the Documents folder in the library section?
What version of Microsoft Office is installed?
Icons expected loss means that files have lost the link with the program which aims to open. It is quite easy to repair.
Follow the tutorial found on this external Web site to associate Microsoft Office files with MS Office programs.
-
Satellite Pro L series starts with the error message
Someone played with the BIOS or whatever on my laptop.
Now, I can't get beyond the log in screen safe mode (black and white) and the error message that oxoooooo7b OXF7A8E63C OXC0000034 rises.
I can not find discs to reboot or something else and don't know what to do to solve the problem.
Any help will be most appreciated, because I'm really at a loss for what to do for the best, that I don't know much about computers as of how put the right problems like this.
Hello
You can try to repair the system.
Switch on and press F8,
Now, you will see the advanced boot options:
Here you can choose the option: last known good configurationIf this option does not help, restart the device and press F8 again.
Choose the first option: fix my computer
Here, you can choose between different options.
You can enable Win 7 to find the problems and fix automatically or you will use the Toshiba HDD recovery option to restore the entire system. -
Original title: opening of the pop ups
I have Vista Home version. When I connect, I get the pop - ups following:
1.) _Windows sidebar Settings.ini. is used by another system.
Recorder 2.) WARNING: Logger! Initialize is not yet call... The log file can corruption exp.
3.) down the application did not start.
Also: while I'm on the internet a pop - up occurs from time to time indicating: "Internet Explorer has stopped working". Sometimes I get started, and sometimes I can just 'X' out and I'm always on.
Hello
1 how long have you been faced with this problem?
2 did you recent hardware or software changes to your computer before this problem?I suggest you try the procedure below.
Step 1: Try to perform the clean boot in order to solve startup error messages.
From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".
Follow the steps provide in the article below to perform the clean boot. http://support.Microsoft.com/kb/929135
Step 2: I suggest you try the steps outlined in the article below to solve the problem of internet Explorer.
http://support.Microsoft.com/kb/936213Thanks and greetings
Umesh P - Microsoft technical support.Visit our Microsoft answers feedback Forum and let us know what you think.
[If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.] -
PS CS4 Extended DB corrupt error message
When you run the Setup program for PS CS4 Extended, an error message that says that the DB is corrupted, and communicate with Adobe. I can't find a way to get a specific support on this issue with Adobe. Ideas?
Hi drt3684,
Please follow the mentioned kb: http://helpx.adobe.com/creative-suite/kb/error-installer-database-corrupt-install.html .
Kind regards
Romit SInha
-
Satellite A135-S4666 - recovery disk displays an error message
The hard drive crashed while I replaced it. I am trying to use the recovery disk to take the computer to the "out of the box configuration.
I chose to 'recover' rather than erase the hard drive based on this choice. Then it copies the files from the first disc and pushes me to the second. After putting the other continues to copy files. Finally, she moves more to 'recover now' she does and seems to be using the hard disk newly installed something between 35 and 50% of the task. At this point, I get an error message stating "error recovery" and invites me to press ok to shut down the computer and spits out the CD. The error message is coded 10-FC12-0002. I tried 4 or 5 times with the same result.
Am I supposed to use disc erase first, and then use the recovery mode since it is a new hard drive? Or I have a defective recovery disc?
Any comments or ideas would be greatly appreciated, I do not get the case at this stage.
Hello
It's not easy to tell if it s a recovery disk problem or if the new HARD drive is the problem. Have you tested a Microsoft disc for example? If the disc of Microsoft is, it seems that your recovery disc is noisy and needs to be replaced. Otherwise the new drive HARD cause this problem.
Check this box to determine the cause of this problem!
Good bye
-
Satellite L300D - recovery disk stops with an error message
Hello
I don't read a lot of the other post, but foung no response...
My problem:
I bought a L300D Vista 1Y there are no included recovery disks, so I made the recovery disc. Now, we wanted to reinstall Vista, so I tried the recovery disk, but after 15 minutes, it failed with an error message:After successfully in 3 partitions of partitioning and formatting them the ImageX tool starts to extract VISTA
After about 57% C:eindows\winsxs\x86_microsoft-windows-ehome-ehcird_31...35.6.0.6000.16663_...\ehcir.ird [removeExtract ToFileByStruct WIMcopyFileEx failed]
Retry...
[error 1117]What happenes about 5 times with similar messages (but other numbers), til message
The request could not be performed because of an i/o errorERROR: ImageX could not to VISTA Lawrence drive HARD C: 2 V: HDD
Press a key...
Aftre reading the threads, I ordered an official recovery (35 Euro!) since the Office of service Toshiba disc, but I got the same errors and messages...
Any ideas what I should do now?
Thank you!!
PS I never had these problems with my other laptops...
Hello
My friend who s a long story.
It's not easy to say what the reason is for this, but to me it sounds like that there is something wrong with the HARD drive. In your case I would format the HARD drive before launching the recovery disc. You can do this with a Microsoft disk to format the whole HARD drive. After that try the recovery disk again.
If it doesn't work, you should check the HARD drive with a special HARD drive diagnostic tool like Drive Fitness Test. use Google to find it, it s freeware and takes only a few minutes.
Welcome them
-
Hello activity (yet) on Vista 32 bit, I receive a message (at the start). Error loading: \App Data\Roaming\pxma2.dll C\Users\ (my name). Access denied. Please notify.
Hello
Cannot find this file on Google so you probably dodged some software malware and you should do a
very thorough control. Message on how to remove the error message if still it y
After the audits of malware.If you need search malware here's my recommendations - they will allow you to
scrutiny and the withdrawal without ending up with a load of spyware programs running
resident who can cause as many questions as the malware and may be more difficult to detect as the
cause.No one program cannot be used to detect and remove any malware. Added that often
easy to detect malicious software often comes with a much harder to detect and remove the
payload. So its best to be now too thorough than paying the high price later. Check
with an extreme overdose point and then run the cleaning only when you are very
that the system is clean.It can be made repeatedly in Mode safe - F8 tap you start, however, you should
also run in regular Windows when you can.Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
(If Rootkits run UnHackMe)Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
Malwarebytes - free
http://www.Malwarebytes.org/Run the malware removal tool from Microsoft
Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.
You should get this tool and its updates via Windows updates - if necessary, you can
Download it here.Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
(Then run MRT as shown above.)Microsoft Malicious - 32-bit removal tool
http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=enMicrosoft Malicious removal tool - 64 bit
http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=enalso install Prevx to be sure that it is all gone.
Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
Prevx - Home - free - small, fast, exceptional CLOUD protection, working with the other security
programs. It is a single scanner, VERY EFFICIENT, if it finds something come back here or
Use Google to see how to remove.
http://www.prevx.com/ <-->-->
http://info.prevx.com/downloadcsi.asp <-->-->Choice of PCmag editor - Prevx-
http://www.PCMag.com/Article2/0, 2817,2346862,00.aspTry the demo version of Hitman Pro:
Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
(viruses, Trojans, rootkits, etc.). who infected your computer despite safe
what you have done (such as antivirus, firewall, etc.).
http://www.SurfRight.nl/en/hitmanpro--------------------------------------------------------
If necessary here are some free online scanners to help the
http://www.eset.com/onlinescan/
-----------------------------------
Original version is now replaced by the Microsoft Safety Scanner
http://OneCare.live.com/site/en-us/default.htmMicrosoft safety scanner
http://www.Microsoft.com/security/scanner/en-us/default.aspx----------------------------------
http://www.Kaspersky.com/virusscanner
Other tests free online
http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1--------------------------------------------------------
Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing system
files.Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup
Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
RUN AS ADMINEnter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker
(SFC.exe) program generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228Run checkdisk - schedule it to run at the next startup, then apply OK your way out then
turn it back on.How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-----------------------------------------------------------------------
If we find Rootkits use this thread and other suggestions. (Run UnHackMe)
I hope this helps.
-
original title: [.] ShellClassInfo] LocalizedResourceName=@%SystemRoot%\system32\shell32.dll,-21787
Remember - this is a public forum so never post private information such as numbers of mail or telephone!
"Ideas: why make this message at startup ' [.] "ShellClassInfo] LocalizedResourceName=@%SystemRoot%\system32\shell32.dll,-21787" how I can remove it?
- You have problems with programs
- Error messages
- Recent changes to your computer
- What you have already tried to solve the problem
The greatest gift that anyone can give to someone else's time. So thank you for your.
Nothing I've tried on this Web site or any other does not prevent the error of dll text block whatever the hell it is.
MS know no more apparently.
but they don't
http://support.Microsoft.com/kb/330132
-
We get the same error messages three times at the start of Windows 2000 on some of our companys computers: "Tcmsvr.dll, file is missing. Computers are Tecra s1 models.
What driver Toshiba is this related to?
Hello
I studied a bit and it seems that this file should be placed in the system32 folder.
In my opinion, this file is part of Toshiba common modules.
I m not 100% sure, but you can try to refresh (restore) the common modules.
Maybe this will help. -
' HP Mini 210-1180NR NetBook, error message at startup PC
I get an error message that indicates;
'RunDLL '.
There was a problem starting
c:\users\Budwind\AppData\Local\Conduit\BackgroundContainer\BackgroundContainer.dllThe specified module could not be found.
The \BackgroundContainer directory does not exist or the other. I looked on my backup file and it isn't here either. What can I do?
Thank you.
1. Select start > Control Panel > administrative tools.
2. open Task Scheduler and click Task Scheduler Library.
3. look in the list for a topic connects to the BackgroundContainer.
4. If found, right-click on it and select Delete.
5. exit all programs and restart the computer when it is done. -
Error message at startup.
I get an error message in my startup saying: C\WINDOWS\$NtUninstallMTF1011$\mmduch.dll. What does that mean?
Hello
It is a component of malware or spyware; You must remove immediately using an antivirus and antispyware program. Follow the links given below to remove the virus.
http://www.Microsoft.com/security/malwareremove/default.aspx
http://OneCare.live.com/site/en-us/default.htm
Hope this information is useful.
Amrita M
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.
Maybe you are looking for
-
Trouble with the long DisplayPort cables?
I'm running a mid MBP 2014 10.11.4 running to an external Dell U2415. I just set up an office of market and wants to run the connector mini-displayport to displayport cable under the desk for a cleaner environment. I took a mini DP to DP 15 ft cable
-
I can't connect a Flir camera to the network
I have problems connecting to a security camera FLIR FX at the network.
-
can't change administrator Standard user
Am wanting to change the kind of user on my computer. Right now its Admimistrator user defined on and I am wanting to change user Stanard, but it wont let me click on it
-
Computer, saying: I have not installed print spooler
Recently, I uninstalled my Dell all-in - One Printer to my computer tries to clear up space on it, and I have a Brother MFC-295CN printer, fax, scanner, copier installed on my computer. But now, since I uninstalled the Dell printer, it tells me that
-
System repair fron start CD requires the administrator password.
Have many problems (right click, explore crashes, slow response) various virus scans find nothing. System Restore does not work (tried 5 more than 6 weeks old Restore Points) I tried the repair from the CD, but the CD is WP SP2 so that it refuses to