SE Error (38): "Exec" should not not while implementiong Java Embedding in BPEL process

Similar Questions

• EqualLogic group member network configuration error: "management interface should not be on the san subnet.

  Hello

  We currently have new EqualLogic 6100 device with this network configuration:

  Director of the IP - 192.168.0.2 (VLAN1).

  Member network config:
  eth0 - 192.168.0.3 (VLAN1)
  eth1 - 10.10.10.3 (VLAN2)
  eth2 - 10.10.10.4 (VLAN2)
  eth3 - 10.10.10.5 (VLAN2)
  ETH4 - empty

  I would attribute 192.168.0.4 to eth4, but received the error: "management interface should not be on the san subnet.

  I am sure that all interfaces eth has access to the VLAN1 and VLAN2, mean error indicates that eth4 should not access VLAN2 and only access the VLAN1 on the switch?

  Or eth0 should also have access to the VLAN2 only to reconfigure eth0 and eth4?

  Thank you

  > The group eating IP should be in iscsi VLANS?

  Yes!

  Note: If configure you an EQL it will ask an iSCSI port because nothing is more necessary to bring it up. The doest previous EQLs have a dedicated Mgmt Port and later, you can convert the last ethX as a MGMT port. This is the reason why configure you ISCSI at the beginning. (Think of a mixed group of newer and older models, and you get a picture)

  OK... once again it is the one and only member of the Group and there is making the production host connected to the right?

  The change of IP address, to a 3rd. subnet for temporary use.

  -Do not touch eth0-3 and the IP address of the group now

  -Configure the MGMT port and IP address management in the tempr group. Subnet. Use the Config-> Adv. Group-> network MGMT. You can change the MGMT Port of the Member, and the address IP of MGMT

  -For the registration of the configuration, you will lose access. You must place your admin PC in the templ. subnet so

  -Connect to the GroupMgr with temp again. INTELLECTUAL PROPERTY

  -Now you can change the IP address of group 10.10.10..x

  -Now you can change eth0 10.10.10.2

  -At the end, you can change the address IP of the Group MANAGEMENT, as well as the MGMT Port to 192.168.0.x

  -Change the IP address of your admin PC rear

  A failover, you should consider to hang a serial cable the active controller of the EQL. Use 9600,8,1, N with your favorite terminal program (putty.exe on windows). All the steps, you can perform from the command line.

  If this group and the only member not in production, but you can reset the config and restart from the beginning.

  Kind regards

  Joerg

• Error: the file is not a valid Java code file

  Hello

  IM new in the development of BB, so bad to describe my problem step by step:

  -First of all, had installed jdk-1_5_0_14-win, BlackBerry_JDE_4.6.0, j2sdk-1_4_2_18-win, Desktop manager 4.6

  -Open BB JDE, create a new workspace

  -Add a project HelloWorldDemo.jdp file (located in the sample folder)

  -Debug the application in the Simulator (9000-JDE) without any error

  -Construction of the project and generate the .axl and .cod files

  -Try to install this app (HelloWorldDemo.cod) in my device with error

  C:\Archivos programa\Research in Motion\BlackBerry JDE 4.6.0\samples\com\rim\samples\device\helloworlddemo>javaloader u load HelloWorldDemo.cod
  Charger Pocket RIM Wireless Java
  Copyright 2001 - 2007 Research In Motion Limited
  Connected
  HelloWorldDemo load error: the file is not a valid Java code file
  7832 bytes sent to ~ 15664 bps
  Disconnected

  -Also try to install the application with Desktop Manager and the .axl file, but show this message "a fatal error has occurred while updating your software to devices." Please try again ".

  My device is a Blackberry 8700

  Software: v4.1.0.351

  Help, please!

  Thank you!

  Thank you!! Problem solved.

• An error has occurred has not got a response from the software update server (update.local). What should I do to update my laptop?

  An error has occurred has not got a response from the software update server (update.local). What should I do to update my laptop?

  It is one of the many problems that occur on my mac.

  Update of OS X El Capitan 10.11.4?

  1. backup Mac.

  2. install 10.11.4 combo update.

  https://support.Apple.com/kb/DL1869?viewlocale=en_US & local = en_US

• Opengl32.dll is not designed to run on windows or it contains an error. I reinstalled the graphics drivers. During the execution of the games, it shows this error. What should I do to fix this?

  Opengl32.dll is not designed to run on windows or it contains an error. I reinstalled the graphics drivers. During the execution of the games, it shows this error. What should I do to fix this? Is it a graphic file or a file from microsoft?

  Hi Jason,

  1. What is the number of brand and model of your system and graphics card?

  2 did you a recent software or hardware changes to the system?

  This error can be caused by an application, including any old games you have installed on your system.

  Because you tried to reinstall the drivers for video card, you can try to perform a clean boot and check if it helps.

  A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

• I just bought Windows 7 upgrade Windows Vista. I get the error message: operation is not supported on this platform. What should I do to get this latest version in my computer?

  The upgrade from Vista to Windows 7

  I just bought Windows 7 upgrade Windows Vista. I get the error message: operation is not supported on this platform. What should I do to get this latest version in my computer?

  Have you tried to do an upgrade installation or a custom installation?  A custom installation requires you to back up your files and settings with Windows Easy Transfer and then reinstall everything after installing the new.  If an update install does not install work, you need to do a custom.

  In addition, a Windows 7 Anytime Upgrade will not work and you get a message from a platform if you have bought a UA and tried to use it with Vista.  Vista upgrade requires a detail, a copy in the Windows 7 box.

• While the plug-and-play was still there at all, and I tried to go I still receive error message 2. could not locate the file.

  Here's the situation.

  First of all only started to the top of my Asus to find was no sound. Following up to plug-and-play service has not started. It is now removed apparently.

  Here are the solutions I tried, in and out of safe mode:

  While the plug-and-play was still there at all, and I tried to go I still receive error message 2. could not locate the file.

  In CMD sfc/scannow reached 32%, then breaks down, saying: it finds corrupted files, but could not fix.

  It Startin via msconfig did not work.

  Tried to go through Device Manager, which is completely empty for some reason any.

  System Restore is restoring before this problem. When you attempt a restore, plug-and-play service is not returned to the existence, defective or otherwise.

  I knew, but there may be malware, mutiple scans with several services did not find anything.

  I tried to contact microsoft help and they might suggest only I have upgraded to windows 10. Tried several times, and he has failed to be upgraded, every time. For the most part just download windows 10 and then by restarting the computer as if nothing happened. Any ideas on how I can fix this?

  Hello

  Welcome to the Microsoft community. I will certainly help you with the problem you are experiencing.

  I would like to ask you:

  • You are running Windows 7 or Windows 10 on your PC?
  • When was the last time it was working fine? Remember to make changes to the computer before this problem?

  Given that you are unable to complete the scan of SFC and Task Manager is empty, usually reinstall or do a repair install is the best choice of action. However, we can try to fix these files and check if that helps. To do this, refer to the steps below:

  1. Open the start menu and type "cmd".
  2. Right-click on the command prompt and click "run as administrator".
  3. Type the following commands and press ENTER after each.

  DISM.exe / Online/Cleanup-image /Scanhealth

  DISM.exe / Online/Cleanup-image /Restorehealth

  After you run these commands, restart the system and check.

  You can also view,

  Difficulty errors of corruption of Windows by using the DISM tool / System Update Readiness

  https://support.Microsoft.com/en-us/KB/947821

  If you are using Windows 7 and have the product key for this. You try to run an upgrade in Place to fix all the corruptions.

  Refer,

  How to perform an upgrade on the spot on Windows Vista, Windows 7, Windows Server 2008 & Windows Server 2008 R2

  Hope this information was useful.

• error orachk 0403-057 syntax error: ' (' should not)

  Hello

  I downloaded the orachk.zip and unpacked and I ran. / orachk on AIX but it gives below error. Please let me know how to solve this problem.

  / dump_area/orachk->. . / orachk

  ksh: 0403-057 syntax error: "(" should not.

  / dump_area/orachk-> vi orachk

  / dump_area/orachk-> sh - x. / orachk

  . / orachk [2]: syntax error at line 887 0403-057: ' (' shouldn't.)

  fixed the problem by installing the Shell BASH on AIX 4.2 - 3.

  orachk run the bash only on AIX

• I get this error message, "could not not use the tool pen because of a program error."  What should I do to fix this?

  Like the above statement, I get this error message, "could not not use the tool pen because of a program error."  What should I do to fix this?   I use PhotoshopCC a lot for work, so if someone could help me quickly, I would be grateful.

  Please read this and acts accordingly (restoration of preferences after making sure all custom presets, actions, patterns, brushes etc. have been registered may be of special interest):

  t http://blogs.Adobe.com/Crawlspace/2012/07/Photoshop-basic-troubleshooting-steps-to-fix-MOS - issues.html

  http://forums.Adobe.com/docs/doc-2325

• I have norton antivirus online via my ISP and I had to disable, because it comes with an error that says "cable not connected or missing network adapter" I use dial-up.

  cable not connected network adapter

  I have norton antivirus online via my ISP and I had to disable, because it comes with an error that says "cable not connected or missing network adapter" I use dial-up and do not use any type of router and I'm not on a network. I also tried to disable my network card & it still says the same error. I have an internal network card that came w / the computer (NOT a PCI one) and I wonder if there is a cord or a plug inside my computer that must be plugged. I made some changes on the internal hardware and might have missed an and I didn't have to open my Tower if it wasn't. It's a big hassle! Help, please!

  Hello

  1. Once you get the error message?

  2. do you get the error when you try to disable Norton anti-virus?

  3. are you able to access the Internet explore?

  Temporarily disable the antivirus on the computer running software and check if you are able to install the software.

  Disable the anti-virus software

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  WARNING: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

• UNION keyword should not

  I'm trying to get the following union query on my coldfusion site:

  < name cfquery = "committee_record."

  DataSource = "AS400a CMTLIB".

  MaxRows = 100

  DbType = "ODBC" >

  SELECT MBRESMPF. MBMID,

  MBRESMPF. MBCYR,

  MBRESMPF. MBCCD,

  MBRESMPF. MBDCD,

  UCase (COMITEPF. CMNAM) AS COM,.

  MBRESMPF. MBMRC,

  UCase (RANKSPF. RKDSC) AS rank.

  MBRESMPF. MBRPT,

  MBRESMPF. SPORT,

  MBRESMPF. MBERP,

  UCase (DIVISNPF. DVNAM) LIKE DIV

  FROM MBRESMPF INNER JOIN RANKSPF ON MBRESMPF. MBMRC = RANKSPF. RKCDE LEFT JOIN COMITEPF ON MBRESMPF. MBCYR = COMITEPF. CMCYR AND MBRESMPF. MBCCD = COMITEPF. CMCCD AND MBRESMPF. MBDCD = COMITEPF. CMDCD LEFT JOIN DIVISNPF ON MBRESMPF. MBDYR = DIVISNPF. DVDYR AND MBRESMPF. MBDCD = DIVISNPF. DVDCD

  WHERE MBRESMPF. MBMRC <>"ORCDVPRN4" AND MBRESMPF. MBMRC <>'ORCIPDRNS' AND MBMID = #id_number #.

  ORDER OF MBRESMPF. MBMID, MBRESMPF. MBCYR / / DESC

  UNION SELECT MBRESMPF. MBMID,

  MBRESMPF. MBCYR,

  MBRESMPF. MBDCD,

  MBRESMPF. MBDCD,

  UCase (DIVISNPF. DVNAM) AS COM,.

  MBRESMPF. MBMRC,

  UCase (RANKSPF. RKDSC) AS rank.

  MBRESMPF. MBRPT,

  MBRESMPF. SPORT,

  MBRESMPF. MBERP,

  UCase (DIVISNPF. DVNAM) LIKE DIV

  FROM MBRESMPF INNER JOIN RANKSPF ON MBRESMPF. MBMRC = RANKSPF. RKCDE LEFT JOIN DIVISNPF ON MBRESMPF. MBDYR = DIVISNPF. DVDYR AND MBRESMPF. MBDCD = DIVISNPF. DVDCD

  WHERE MBRESMPF. MBMRC = "ORCDVPRN4" OR MBRESMPF. MBMRC = 'ORCIPDRNS' AND MBMID = #id_number #.

  ORDER OF MBRESMPF. MBMID, MBRESMPF. MBCYR / / DESC

  < / cfquery >

  But I get the following error message:

  Error Diagnostic information

  Of ODBC error code = 37000 (syntax error or access violation)

  [IBM] [iSeries Access ODBC Driver] [DB2 UDB] SQL0199 - keyword UNION should not. Let's take valid: TO USE SKIP WAIT WITH FETCH OPTIMIZE.

  The error occurred while processing an element with a general identifier of (CFQUERY), occupying the position of document (19:1) (22:23).

  This query works for me no problem in Microsoft Access.  Someone at - it suggestions?

  Thank you!

  I'm surprised that it works in Access, but from my experience a UNION query generally expected a single ORDER BY the end (a recordset that is the result of the union is so orderly and not to each recordset that contributes to the union)?  I'm not able to test this right now, sorry.

  --

  Adam

• Subjects shown in the search results which should not show

  When I saw the compiled help file and do a search for a word it's subjects displaying that I don't want to show. These topics are not in the table of contents and are not indexed.
  
  I inherited our co writer Tech so I learn about HR by trial and error. I use RH7. The help files are created in the HR 5 (or earlier) but had to install on Vista RH7.
  
  While working on an existing HR help file I have a few topics that were mistakes, from me to experiment, or are the old one that I am updating and change. In both cases, I thought I could leave them hidden inside, just for safety or return to. I guess if they have not been put in the TOC or indexed, that they should not show to the outside world. When I search on a word that is in the title of the topic or text these topics are listed.
  
  Can I prevent it from is displayed in search? They do not show in the TOC, and they do not show in the Index. Is my only option to remove? I have looked through the properties of the subject and can't find a solution.
  
  Thank you
  
  Jim

  I should add for example I created a label called Admin building, and I attribute it to themes and content in the project for my own reference, but customers shouldn't see. I also have tags assigned to a content build that is inserted in my project of changes to the software that are further down the road the next version so I can exclude until the release is ready.

• iPhoto should not run every time that a device is connected

  iPhoto should not start when I plug any device on a computer.   This should be controlled by the owner of the device on the device. And this should be a configurable feature on the computer.  There should be a check box that says "Click here to have the automatic iPhoto launch when you plug in a device."

  I don't want to plug my phone in a my computer from a friend to have all photos hot, I took with his girlfriend while he was out of popup city on his screen while my phone charges.

  I want this automatic launch when my girlfriend plug her phone on my computer to load so I can watch through his albums.

  I won't launch when my father its branch on my computer because the things a child should not see their parents.

  Already, this option exists in iPhoto and iTunes, but you can check it or uncheck the box only when other devices are connected. You can also do this via the image transfer application in your Applications folder.

• Error messages - rundll does not - occurs on my new Equium

  I have a new computer satellite phone on Vista - about 4 weeks - and I get the error messages: rundll is not working, Windows graphical desktop does not work.

  Should I return to the retailer or ask for help on this site?

  Help appreciated - thank you.

  Before contacting the retailer I recommend you to use recovery media supplied and reinstall the OS. I hope once this laptop will work fine as before.

• Desktop PC's processor HP 251 - a11, Windows 10, AMD quad core A6-6310 accelerated with 4 GB memory DDR3 system and 500 GB hard drive. I installed I tunes last version and cannot operate.  Error message says Hello not activated.  Tells me to

  Desktop PC's processor HP 251 - a11, Windows 10, AMD quad core A6-6310 accelerated with 4 GB memory DDR3 system and 500 GB hard drive. I installed I tunes last version and cannot operate.  Error message says Hello not activated.  Tells me to go to the Control Panel then administrative tools and allow to Hello.  I followed these instructions, but I can't activate Hello.  What did wrong and how I can activate the Hello?  My email is * any help is greatly appreciated

  < email published by host >

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2