Server cannot connect to the https
I found the installation of software that our main server cannot access any site that requires https. I checked using Internet explore and firefox and no work. We have a Sonicwall firewall but can't find anything obvious here.
Please contact a forum that manages your server product. If it is Windows server, then check on http://social.technet.microsoft.com/Forums/
You can also add more details when reposting here, as the description above is not much information about the problem.
Tags: Windows
Similar Questions
-
Security Server cannot connect to the replica to connect to the server
HelloI want to set up two security servers. Each connected to a login server.
The installation of the Security Server works only when I connect to the backend connection.
Telnet using port 4001 to replicas login server does not work. (from the Security Server)
On the login replica server firewall rules seems to be OK.
Who can help me here?
Jan Willem
It certainly works. Have two security servers, each associated with a connection to the server (for example a standard and the other a replica) is a very common scenario.
Double check the rules in your firewall if you have an external firewall between your security servers and connection. Check for the setting procedure Administrator's guide matching password etc and for matching Security Server Troubleshooting section. Make sure that the two security servers are configured the same (no group political advertising strategies of firewall different, firewalls running on all servers etc..). Make sure that the two connection servers are configured the same.
Let us know what it was.
Mark
-
ESXi server cannot connect to the netowrk
Hello
I have installed ESXI 6 on a new host, and that you have set up the network in the usual way, but it can not ping to the gateway. I can see all the Nic are connected and have checked the settings. I looked in the newspaper and may see the following errors
In the newspaper vobd I see the State of the physical link is up, followed by an event (esx.clear.net.vmnic.linkstate.up) could not be sent immediately to spend; tail to try again
the newspaper cannot open the file DictionaryLoad:"//.vmware/preferences': no such file or directory
Thank you
Paul
What are the ports on the switch uplink? Trunk or access?
If trunk do you have native located on the port Vlan (switch side)?
R
-
Server cannot connect to the cluster
Hello
I was scratching my head on this problem for a while. I have three servers using the same file config-cache-coherence: run within weblogic, one is the control application coherence.sh and the third is an invocation of the java class DefaultCacheServer. All servers are running on the same computer.
Oddly enough, the first two connect properly while the latter does not.
You can see the members of the cluster first two in this release of coherence.sh:
Bq. Lt & 17:13:27.132 2008-12-16 Oracle coherence GE 3.3.1/389; D5 & gt; (thread = Cluster Member = n/a): Service DistributedCache is 1 associate member senior member 1-SafeCluster: Name = essOM------group {address = 224.3.3.1, Port = 4490, TTL = 0}
However, when I got the hang of the DefaultCacheServer I get the following
Bq. Oracle Version consistency 3.3.1/389-Grid edition: development------Copyright (c) 2000-2007 Oracle. All rights reserved. ------Lt & 17:00:17.697 2008-12-16 Oracle coherence GE 3.3.1/389; Info & gt; (thread = main Member, = n/a): cache configuration loaded resources ' file:/ex-port/home/sef/projects/ESS/weblogicDomains/essSHdomain/db-ess/config/coherence/coherence-cache-config.xml '-3.3.1/389 Oracle coherence GE 2008-12-16 17:00:17.741 & lt; Info & gt; (thread = main Member, = n/a): loaded cache of the file configuration "/ export/home-/sef/projects/ESS/weblogicDomains/essSHdomain/db-ess/config/coherence/coherence-cache-config.xml"-3.3.1/389 Oracle coherence GE 2008-12-16 17:00:17.745 & lt; Info & gt; (thread = main Member, = n/a): started DefaultCacheServer...-SafeCluster: null
I understand that this is not enough information to fully solve the problem but I would like to apprecia\te all tips and direcxtions to solve this. If more info is needed I will find and post here
Regardsd
Steve hedges
Deutsche Bank
Hi Steve,.
Looks like you don't have
true (see http://wiki.tangosol.com/display/COH33UG/distributed-scheme) in the cache configuration descriptor.Kind regards
Dimitri -
Get this error when you try to send mails. Outlook express
AVG is the cause of this error message. Try to disable mail scan in AVG and see if that helps. (Tip: AVG is causing more headaches with each update.) You may want to consider another AV program is more compatible with Outlook Express). Bruce Hagen
MS - MVP October 1, 2004 ~ September 30, 2010
Imperial Beach, CA -
Outlook: "cannot get mail" "cannot connect to the server.
April 6 at 7:00 PM CST, my iPhone 5 running iOS stopped syncing with my Microsoft Outlook account 9.3.1.
I did have problems with my iPhone sync with my Outlook email over the past 5 years so far.
My Outlook account is to these servers-
web mail:
https://blu183.mail.live.com/for Windows Live Mail 2012:
https://mail.Services.live.com/DeltaSync_v2.0.0/sync.aspxI tried to delete my Outlook account from my iPhone and re-establishment and the account Outlook 'checks' correctly - but this does not solve the problem.
The iPhone keeps displaying a pop-up message:
"Cannot get mail" "cannot connect to the server.My iPhone is syncing correctly with my Gmail accounts and iCloud.
Also, I created my Outlook account on iPad to my daughter who is running iOS 8.1.2 and I have the same problem.
This seems to be a situation of the Apple servers, do not sync with Microsoft servers.
Thank you
It seems that Outlook is to have questions, not only with iPhones but W10, see this thread:
-
FSX won't turn on, says that it cannot connect to the server
Hey, I tried to register my copy of Microsoft flight simulator X deluxe edition and it does not work I tried to register it hourly it says it cannot connect to the server);
Hello
What version of Windows operating system do you use?
I suggest you to consult the following Microsoft article and check if it helps.
Solve problems with activation for Microsoft games problems and mapping programs
http://support.Microsoft.com/kb/960480
Note : the steps mentioned below includes the modification of the system registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
Back up the registry: http://windows.microsoft.com/en-US/windows7/Back-up-the-registryAlso see: frequently asked questions on how to enable Microsoft Games for Windows, streets and trips and Mappoint: http://support.microsoft.com/kb/927007If you still experience the problem, then I suggest to contact with support of Flight Simulator for further assistance.
http://support.Microsoft.com/GP/games-for-Windows
http://www.Microsoft.com/products/games/FSInsider/tips/pages/default.aspx
-
I have a laptop Toshiba Satellite M105-S3041 with Windows XP Home Edition. I received the error message listed above indicating that Windows cannot connect Internet using HTTP, HTTPS, or FTP. When I open the wireless network connection status, I see packets sent and I also see that I get both packets.
The opening to the top of Internet Explorer, I received the error message listed above. When I go to the properties of my wireless adapter and examine the properties of the TCP/IP parameters, I see that I have "obtain an IP address automatically" and "Obtain DNS server address automatically" checked. On the general tab of TCP/IP properties, I clicked on the tab advanced and click on the tab options to display the TCP/IP filtering settings and clicked the properties button. Here, I see that the ports TCP, UDP and IP PROTOCOL. I have a check the box 'enable TCP/IP filtering '.
Please help me because I am still unable to connect to the internet.
[snip]... On the general tab of TCP/IP properties, I clicked on the tab advanced and click on the tab options to display the TCP/IP filtering settings and clicked the properties button. Here, I see that the ports TCP, UDP and IP PROTOCOL. I have a check the box 'enable TCP/IP filtering '.
In general, you don't want to have a check in the box "enable TCP/IP filtering. Try to uncheck this box and see if it helps.
If this does not help, two programs freeware difficulty sometimes of the problems of this kind... Try to run LSPFix and/or WinSockXPFix. Alternatively, you can try to reset your IP stack...
"How to reset the Protocol Internet (TCP/IP)"
<>http://support.Microsoft.com/kb/299357 >HTH,
JW -
Media Player cannot connect to the server - Original COOD2EE7 error code
Tried media player - tools - options-network. Cannot configure the Protocol / the proxy settings. Streaming proxy settings area is empty.
Hello Adelek,
Thank you for posting. It seems that you may have a firewall problem. I that you would suggest to check your firewall settings to see if it's to allow access of media player. I've also included some basic information about this error.
Please let me know if this helps you.
You got the C00D1198 error message when you use Windows Media Player. The following information can help you resolve the problem.
Unable to connect to the server
Windows Media Player cannot connect to the server that hosts the content you want to listen to. You may encounter this error message for the following reasons:
The name of the server that hosts the content is not valid. If you typed an address Uniform Resource Locator (URL) in the open URL dialog box, verify that the file name is spelled correctly and that the path to the file is correct, and then try again. If you clicked a link on a Web page, the link isn't valid.
The server is not available (for example, the server is busy or not online). Try again later.
For Windows Media Player proxy server settings are not configured correctly. Verify that your proxy server settings are correct.
To check your proxy server settings
Click the arrow below the now playing tab, and then click More Options.
Click the network tab.
Check your settings in the Streaming proxy settings area.
Note
If you don't know what your proxy server settings should be, on the network tab, select a Protocol, click on configure, then select Autodetect proxy settings or use the the proxy settings of the browser (available for HTTP protocol only).
Zack
Engineer Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think. -
established - VPN connection, but cannot connect to the server?
vpn connection AnyConnect is implemented - but cannot connect to the server? The server IP is 192.168.0.4
Thank you
ASA Version 8.2 (1)
!
hostname ciscoasa5505
names of
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.0.3 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 208.0.0.162 255.255.255.248
!
interface Vlan5
Shutdown
prior to interface Vlan1
nameif dmz
security-level 50
IP address dhcp setroute
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
clock timezone PST - 8
clock summer-time recurring PDT
DNS lookup field inside
DNS server-group DefaultDNS
192.168.0.4 server name
Server name 208.0.0.11
permit same-security-traffic intra-interface
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service TS-780-tcp - udp
port-object eq 780
object-group service Graphon tcp - udp
port-object eq 491
Allworx-2088 udp service object-group
port-object eq 2088
object-group service allworx-15000 udp
15000 15511 object-port Beach
object-group service udp allworx-2088
port-object eq 2088
object-group service allworx-5060 udp
port-object eq sip
object-group service allworx-8081 tcp
EQ port 8081 object
object-group service web-allworx tcp
EQ object of port 8080
allworx udp service object-group
16001 16010 object-port Beach
object-group service allworx-udp
object-port range 16384-16393
object-group service remote tcp - udp
port-object eq 779
object-group service billing1 tcp - udp
EQ object of port 8080
object-group service billing-1521 tcp - udp
port-object eq 1521
object-group service billing-6233 tcp - udp
6233 6234 object-port Beach
object-group service billing2-3389 tcp - udp
EQ port 3389 object
object-group service olivia-3389 tcp - udp
EQ port 3389 object
object-group service olivia-777-tcp - udp
port-object eq 777
netgroup group of objects
network-object host 192.168.0.15
network-object host 192.168.0.4
object-group service allworx1 tcp - udp
8080 description
EQ object of port 8080
allworx_15000 udp service object-group
15000 15511 object-port Beach
allworx_16384 udp service object-group
object-port range 16384-16393
DM_INLINE_UDP_1 udp service object-group
purpose of group allworx_16384
object-port range 16384 16403
object-group service allworx-5061 udp
range of object-port 5061 5062
object-group service ananit tcp - udp
port-object eq 880
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing-6233
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing-1521
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing2-3389
outside_access_in list extended access permit tcp any host 208.0.0.164 eq https
outside_access_in list extended access permit tcp any host 208.0.0.164 eq www
outside_access_in list extended access permit tcp any host 208.0.0.164 eq ftp
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.164 object-group billing1
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 EQ field
outside_access_in list extended access permit tcp any host 208.0.0.162 eq www
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 remote object-group
outside_access_in list extended access permit tcp any host 208.0.0.162 eq smtp
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 object-group olivia-777
outside_access_in list extended access permit udp any host 208.0.0.162 - group Allworx-2088 idle object
outside_access_in list extended access permit udp any host 208.0.0.162 object-group inactive allworx-5060
outside_access_in list extended access permit tcp any host 208.0.0.162 object-group web-allworx inactive
outside_access_in list extended access permit tcp any host 208.0.0.162 object-group inactive allworx-8081
outside_access_in list extended access permit udp any host 208.0.0.162 object-group inactive allworx-15000
outside_access_in list extended access permit udp any host 208.0.0.162 DM_INLINE_UDP_1 idle object-group
outside_access_in list extended access permit udp any host 208.0.0.162 object-group inactive allworx-5061
outside_access_in list extended access allowed object-group TCPUDP any host 208.0.0.162 inactive ananit object-group
outside_access_in list extended access deny ip host 151.1.68.194 208.0.0.164
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 172.16.0.0 255.255.0.0
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.1.0 255.255.255.0
permit access ip 192.168.0.0 scope list outside_20_cryptomap 255.255.255.0 172.16.0.0 255.255.0.0
Ping list extended access permit icmp any any echo response
inside_access_in of access allowed any ip an extended list
permit access ip 192.168.0.0 scope list outside_cryptomap 255.255.255.0 192.168.1.0 255.255.255.0
access-list 1 standard allow 192.168.0.0 255.255.255.0
pager lines 24
Enable logging
logging buffered stored notifications
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 dmz
IP local pool 192.168.100.30 - 192.168.100.60 mask 255.255.255.0 remote_pool
192.168.0.20 mask - distance local pool 255.255.255.0 IP 192.168.0.50
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 1 192.168.0.0 255.255.255.0
alias (inside) 192.168.0.4 99.63.129.65 255.255.255.255
public static tcp (indoor, outdoor) interface 192.168.0.4 smtp smtp netmask 255.255.255.255
public static tcp (indoor, outdoor) interface field 192.168.0.4 netmask 255.255.255.255 area
public static tcp (indoor, outdoor) interface 192.168.0.4 www www netmask 255.255.255.255
public static tcp (indoor, outdoor) interface 777 192.168.0.15 777 netmask 255.255.255.255
public static tcp (indoor, outdoor) interface 779 192.168.0.4 779 netmask 255.255.255.255
public static (inside, outside) udp interface field 192.168.0.4 netmask 255.255.255.255 area
public static tcp (indoor, outdoor) interface 880 192.168.0.16 880 netmask 255.255.255.255
static (inside, outside) 208.0.0.164 tcp 3389 192.168.0.185 3389 netmask 255.255.255.255
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 208.0.0.161 1
Route inside 192.168.50.0 255.255.255.0 192.168.0.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.0.0 255.255.255.0 inside
http 192.168.0.3 255.255.255.255 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Sysopt noproxyarp inside
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 108.0.0.97
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
card crypto outside_map 20 match address outside_20_cryptomap
card crypto outside_map 20 set pfs
peer set card crypto outside_map 20 69.0.0.54
outside_map crypto 20 card value transform-set ESP-3DES-SHA
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 5
preshared authentication
3des encryption
sha hash
Group 2
life no
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 1
life no
Telnet timeout 5
SSH timeout 5
Console timeout 0
identifying client DHCP-client interface dmz
dhcpd outside auto_config
!
dhcpd address 192.168.0.20 - 192.168.0.50 inside
dhcpd dns 192.168.0.4 208.0.0.11 interface inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
SVC disk0:/anyconnect-win-2.5.2014-k9.pkg 1 image
enable SVC
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
internal group anyconnect strategy
attributes of the strategy group anyconnect
VPN-tunnel-Protocol svc webvpn
WebVPN
list of URLS no
SVC request enable
encrypted olivia Zta1M8bCsJst9NAs password username
username of graciela CdnZ0hm9o72q6Ddj encrypted password
tunnel-group 69.0.0.54 type ipsec-l2l
IPSec-attributes tunnel-group 69.0.0.54
pre-shared-key *.
tunnel-group 108.0.0.97 type ipsec-l2l
IPSec-attributes tunnel-group 108.0.0.97
pre-shared-key *.
tunnel-group anyconnect type remote access
tunnel-group anyconnect General attributes
remote address pool
strategy-group-by default anyconnect
tunnel-group anyconnect webvpn-attributes
Group-alias anyconnect enable
!
Global class-card class
match default-inspection-traffic
!
!
World-Policy policy-map
Global category
inspect the icmp
!
service-policy-international policy global
: end
ASDM location 208.0.0.164 255.255.255.255 inside
ASDM location 192.168.0.15 255.255.255.255 inside
ASDM location 192.168.50.0 255.255.255.0 inside
ASDM location 192.168.1.0 255.255.255.0 inside
don't allow no asdm history
Right now your nat 0 (NAT exemption) follows the access list:
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 172.16.0.0 255.255.0.0
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.1.0 255.255.255.0
Traffic back from your server to 192.168.0.4 in the pool of VPN (192.168.0.20 - 50) not correspond to this access list and thus be NATted. The TCP connection will not develop due to the failure of the Reverse Path Forwarding (RPF) - traffic is asymmetric NATted.
Then try to add an entry to the list of access as:
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.0.0 255.255.255.0
It's a bit paradoxical but necessary that your VPN pool is cut out in your interior space network. You could also do like André offers below and use a separate network, but you would still have to add an access list entry to exempt outgoing NAT traffic.
-
Cannot connect to the activation server
I tried to allow my computer with my adobe ID, but an error message appears. The permission toolbar appears for a few seconds, but then an error message comes up saying "cannot connect to the activation server. Check that you are connected to the internet. »
I am currently connected to the internet and that you have added Digital Editions 3.0 to the my firewall programs authorized. I use windows 7. I also tried deauthrorizing my computer by pressing SHIFT + CTRL + D.
I found the problem.
http://tohellmylovewithyou.WordPress.com/2010/08/05/ADE/
Check out the link for more info
-
Cannot connect to the XMLDB via http, ftp, webdav
I can connect to XDB through a DEV instance on the same server, but cannot connect to the instance SCIDEV. The differences are THAT DEV is nls_characterset WE8MSWIN1252. SCIDEV is AL32UTF8. DEV has ports 8080 and 2100. SCIDEV has ports 8089 and 2102. HTTP request continuously a user / password without error. Watch FTP authentication failed. WebDAV continually requires a user name and password. I've tried a few things with no luck yet. What should I do to be able to connect? It is also published in Oracle support as SR 3-3043961271 technique. Please do not share the files downloaded in this forum SR.
Follow the different SQL commands. Running Windows2003 Server and Windows XP SP2 client.
Status of the listener followsSYSTEM@scidev> select * from v$version; Oracle Database 11g Release 11.2.0.2.0 - Production PL/SQL Release 11.2.0.2.0 - Production CORE 11.2.0.2.0 Production TNS for 32-bit Windows: Version 11.2.0.2.0 - Production NLSRTL Version 11.2.0.2.0 - Production 5 rows selected. SYSTEM@scidev> select * from nls_session_parameters; PARAMETER VALUE ---------------------------------------- --------------------------------------- NLS_LANGUAGE AMERICAN NLS_TERRITORY AMERICA NLS_CURRENCY $ NLS_ISO_CURRENCY AMERICA NLS_NUMERIC_CHARACTERS ., NLS_CALENDAR GREGORIAN NLS_DATE_FORMAT DD-MON-RR NLS_DATE_LANGUAGE AMERICAN NLS_SORT BINARY NLS_TIME_FORMAT HH.MI.SSXFF AM NLS_TIMESTAMP_FORMAT DD-MON-RR HH.MI.SSXFF AM NLS_TIME_TZ_FORMAT HH.MI.SSXFF AM TZR NLS_TIMESTAMP_TZ_FORMAT DD-MON-RR HH.MI.SSXFF AM TZR NLS_DUAL_CURRENCY $ NLS_COMP BINARY NLS_LENGTH_SEMANTICS BYTE NLS_NCHAR_CONV_EXCP FALSE 17 rows selected. SYSTEM@scidev> select * from nls_database_parameters; PARAMETER VALUE ---------------------------------------- --------------------------------------- NLS_NCHAR_CHARACTERSET AL16UTF16 NLS_LANGUAGE AMERICAN NLS_TERRITORY AMERICA NLS_CURRENCY $ NLS_ISO_CURRENCY AMERICA NLS_NUMERIC_CHARACTERS ., NLS_CHARACTERSET AL32UTF8 NLS_CALENDAR GREGORIAN NLS_DATE_FORMAT DD-MON-RR NLS_DATE_LANGUAGE AMERICAN NLS_SORT BINARY NLS_TIME_FORMAT HH.MI.SSXFF AM NLS_TIMESTAMP_FORMAT DD-MON-RR HH.MI.SSXFF AM NLS_TIME_TZ_FORMAT HH.MI.SSXFF AM TZR NLS_TIMESTAMP_TZ_FORMAT DD-MON-RR HH.MI.SSXFF AM TZR NLS_DUAL_CURRENCY $ NLS_COMP BINARY NLS_LENGTH_SEMANTICS BYTE NLS_NCHAR_CONV_EXCP FALSE NLS_RDBMS_VERSION 11.2.0.2.0 20 rows selected. SYSTEM@scidev> select * from dba_errors; no rows selected SYSTEM@scidev> select count(*) from dba_objects 2 where owner='XDB' and status='INVALID'; COUNT(*) --------------- 0 1 row selected. SYSTEM@scidev> select comp_name, status, version from dba_registry 2 where comp_name='Oracle XML Database'; COMP_NAME --------------------------------------------------------------------------------- STATUS VERSION -------------------------------------------- ------------------------------ Oracle XML Database VALID 11.2.0.2.0 1 row selected. SYSTEM@scidev> show parameter dispatchers NAME TYPE VALUE ------------------------------------ ----------- ------------------------------ dispatchers string (PROTOCOL=TCP) (SERVICE=scidev XDB) max_dispatchers integer NULL SYSTEM@scidev> SYSTEM@scidev> select dbms_xdb.gethttpport from dual; GETHTTPPORT --------------- 8089 1 row selected. 1* SELECT DBMS_XDB.getaclDocument('/home/').getClobVal() FROM DUAL SYSTEM@scidev> / <acl description="Public:All privileges to PUBLIC" xmlns="http://xmlns.oracle.com/xdb/acl.xsd" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://xmlns.oracle.com/xdb/acl .xsd http://xmlns.oracle.com/xdb/acl.xsd" shared="true"> <ace> <grant>true</grant> <principal>PUBLIC</principal> <privilege> <all/> </privilege> </ace> </acl> 1 row selected. SYSTEM@scidev> 1* SELECT DBMS_XDB.getaclDocument('/home/pharma').getClobVal() FROM DUAL SYSTEM@scidev> / <acl description="Private:All privileges to OWNER only and not accessible to others" xmlns="http://xmlns.oracle.com/xdb/acl.xsd" xmlns:dav="DAV:" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://xmlns.oracle.com/xdb/acl.xsd http://xmlns.oracle.com/xdb/acl.xsd" shared="true"> <ace> <grant>true</grant> <principal>dav:owner</principal> <privilege> <all/> </privilege> </ace> </acl> 1 row selected.
Http and ftp to SCIDEV ports are resolved in Enterprise Manager at 8089 and 2102.D:\oracle>lsnrctl status LSNRCTL for 32-bit Windows: Version 11.2.0.2.0 - Production on 02-MAR-2011 12:40:57 Copyright (c) 1991, 2010, Oracle. All rights reserved. Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=localhost)(PORT=1521))) STATUS of the LISTENER ------------------------ Alias LISTENER Version TNSLSNR for 32-bit Windows: Version 11.2.0.2.0 - Production Start Date 21-FEB-2011 22:58:56 Uptime 8 days 13 hr. 42 min. 2 sec Trace Level off Security ON: Local OS Authentication SNMP OFF Listener Parameter File D:\oracle\path\network\admin\listener.ora Listener Log File D:\oracle\path\listener\alert\log.xml Listening Endpoints Summary... (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=localhost)(PORT=1521))) (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC0ipc))) (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=localhost)(PORT=8089))(Presentation=HTTP)(Session=RAW)) (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=localhost)(PORT=2102))(Presentation=FTP)(Session=RAW)) (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=localhost)(PORT=8080))(Presentation=HTTP)(Session=RAW)) (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=localhost)(PORT=2100))(Presentation=FTP)(Session=RAW)) Services Summary... Service "DEVXDB.aa.ad.epa.gov" has 1 instance(s). Instance "dev", status READY, has 1 handler(s) for this service... Service "PLSExtProc" has 1 instance(s). Instance "PLSExtProc", status UNKNOWN, has 1 handler(s) for this service... Service "dev" has 1 instance(s). Instance "dev", status UNKNOWN, has 1 handler(s) for this service... Service "dev.aa.ad.epa.gov" has 1 instance(s). Instance "dev", status READY, has 1 handler(s) for this service... Service "scidev.aa.ad.epa.gov" has 1 instance(s). Instance "scidev", status READY, has 1 handler(s) for this service... Service "scidevXDB.aa.ad.epa.gov" has 1 instance(s). Instance "scidev", status READY, has 1 handler(s) for this service... The command completed successfully D:\oracle>
FTP log follows. First connect you to DEV successfully. Then connect you to SCIDEV fails.
But I can log in with the same user in sql plusWINSOCK.DLL: WinSock 2.0 WS_FTP95 LE 4.60 98.03.17, Copyright © 1992-1998 Ipswitch, Inc. local chdir to c: - - connecting to localhost:2100 Connected to localhost port 2100 220- servername Unauthorised use of this FTP server is prohibited and may be subject to civil and criminal prosecution. 220 servername FTP Server (Oracle XML DB/Oracle Database) ready. USER xdb 331 pass required for XDB PASS (hidden) 230 XDB logged in PWD 257 "/" is current directory. Host type (I): UNIX (standard) PORT theIPaddress,15,15 200 PORT Command successful LIST 150 ASCII Data Connection Received 250 bytes in 0.1 secs, (20.00 Kbps), transfer succeeded 226 ASCII Transfer Complete QUIT 221 QUIT Goodbye. local chdir to c: - - connecting to localhost:2102 Connected to localhost port 2102 220- servername Unauthorised use of this FTP server is prohibited and may be subject to civil and criminal prosecution. 220 servername FTP Server (Oracle XML DB/Oracle Database) ready. USER xdb 331 pass required for XDB PASS (hidden) 530 login error ! Logon failure, so quittingSYSTEM@scidev> connect xdb@scidev Enter password: *********************** Connected. XDB@scidev> select user, sysdate from dual; USER SYSDATE ------------------------------ --------- XDB 02-MAR-11 1 row selected. XDB@scidev>This is starting to look like bug 6049194. Please open an S/R with Support of Oracle
-
My 5s iphone suddenly showed no service, then I made an attempt to update to ios and itunes connected, now iphone is not enable and display cannot connect to the server and in itunes it shows unable to check your device.please help me
Assuming that you have a valid SIM card in the phone, it is more often symptomatic of a phone that has been hacked or jailbroken to unlock.
Where do you have the phone first?
-
iPhone cannot connect to the server to iCloud
Hello!
My son IPhone cannot connect to the server iCloud. App Store is not available. In the iTunes and App Store from the settings app, I can't log in. IPhone resetting is not possible. Restore from iTunes on Mac is not possible, because find my iPhone is active on the iPhone, and it cannot be turned off, because in the pane of the application of the iCloud settings can't do anything until I have to accept the new terms and conditions, which cannot be made.
WiFi on the phone works great with Safari, Mail, but cannot get new e-mail messages. The weather application does not connect.
His iPad that is connected to the same iCloud account has no problem and there is no problem to connect to his account on iCloud.com.
I tried to restart and reset hard iPhone and updated to 9.3.4 via iTunes on Mac (which went without pain, but doesn't change anything).
Any help much appreciated!
Does anyone have advice at all...? Aside from throwing the thing?
-
Help! Safari cannot connect to the server
I really need help! I tried to forget the network and turning it back on, I have disabled the firewall and remove all extensions of safari. I seems that nothing works.
I get the message 'Safari cannot connect to the server' on almost every site except this and facebook. I can't enter same Urbanoutfitters.com or ASOS. I just got the message "Safari could not connect to Server" I'm not a computer genius so hopefully someone here can help me...
You may have installed one or more variants of the malware "VSearch' ad-injection. Please back up all data, and then take the steps below to disable it.
Do not use any type of product, "anti-virus" or "anti-malware" on a Mac. It is never necessary for her, and relying on it for protection makes you more vulnerable to attacks, not less.
Malware is constantly evolving to work around defenses against it. This procedure works now, I know. It will not work in the future. Anyone finding this comment a couple of days or more after it was published should look for a more recent discussion, or start a new one.
Step 1
VSearch malware tries to hide by varying names of the files it installs. It regenerates itself also if you try to remove it when it is run. To remove it, you must first start in safe mode temporarily disable the malware.
Note: If FileVault is enabled in OS X 10.9 or an earlier version, or if a firmware password is defined, or if the boot volume is a software RAID, you can not do this. Ask for other instructions.
Step 2
When running in safe mode, load the web page and then triple - click on the line below to select. Copy the text to the Clipboard by pressing Control-C key combination:
/Library/LaunchDaemons
In the Finder, select
Go ▹ go to the folder...
from the menu bar and paste it into the box that opens by pressing command + V. You won't see what you pasted a newline being included. Press return.
A folder named "LaunchDaemons" can open. If this is the case, press the combination of keys command-2 to select the display of the list, if it is not already selected.
There should be a column in the update Finder window. Click this title two times to sort the content by date with the most recent at the top. Please don't skip this step. Files that belong to an instance of VSearch will have the same date of change for a few minutes, then they will be grouped together when you sort the folder this way, which makes them easy to identify.
Step 3
In the LaunchDaemons folder, there may be one or more files with the name of this form:
com Apple.something.plist
When something is a random string, without the letters, different in each case.
Note that the name consists of four words separated by dots. Typical examples are:
com Apple.builins.plist
com Apple.cereng.plist
com Apple.nysgar.plist
There may be one or more items with a name of the form:
com.something.plist
Yet once something is a random string, without meaning - not necessarily the same as that which appears in one of the other file names.
These names consist of three words separated by dots. Typical examples are:
com.semifasciaUpd.plist
com.ubuiling.plist
Sometimes there are items (usually not more than one) with the name of this form:
com.something .net - preferences.plist
This name consists of four words (the third hyphen) separated by periods. Typical example:
com.jangly .net - preferences.plist
Drag all items in the basket. You may be prompted for administrator login password.
Restart the computer and empty the trash.
Examples of legitimate files located in the same folder:
com.apple.FinalCutServer.fcsvr_ldsd.plist
com Apple.Installer.osmessagetracing.plist
com Apple.Qmaster.qmasterd.plist
com Apple.aelwriter.plist
com Apple.SERVERD.plist
com Tether.plist
The first three are clearly not VSearch files because the names do not match the above models. The last three are not easy to distinguish by the name alone, but the modification date will be earlier than the date at which VSearch has been installed, perhaps several years. None of these files will be present in most installations of Mac OS X.
Do not delete the folder 'LaunchDaemons' or anything else inside, unless you know you have another type of unwanted software and more VSearch. The file is a normal part of Mac OS X. The "demon" refers to a program that starts automatically. This is not inherently bad, but the mechanism is sometimes exploited by hackers for malicious software.
If you are not sure whether a file is part of the malware, order the contents of the folder by date modified I wrote in step 2, no name. Malicious files will be grouped together. There could be more than one such group, if you attacked more than once. A file dated far in the past is not part of the malware. A folder in date dated Middle an obviously malicious cluster is almost certainly too malicious.
If the files come back after you remove the, they are replaced by others with similar names, then either you didn't start in safe mode or you do not have all the. Return to step 1 and try again.
Step 4
Reset the home page in each of your browsers, if it has been modified. In Safari, first load the desired home page, then select
▹ Safari preferences... ▹ General
and click on
Set on the current Page
If you use Firefox or Chrome web browser, remove the extensions or add-ons that you don't know that you need. When in doubt, remove all of them.
The malware is now permanently inactivated, as long as you reinstall it never. A few small files will be left behind, but they have no effect, and trying to find all them is more trouble that it's worth.
Step 5
The malware lets the web proxy discovery in the network settings. If you know that the setting was already enabled for a reason, skip this step. Otherwise, you should undo the change.
Open the network pane in system preferences. If there is a padlock icon in the lower left corner of the window, click it and authenticate to unlock the settings. Click the Advanced button, and then select Proxies in the sheet that drops down. Uncheck that Auto Discovery Proxy if it is checked. Click OK, and then apply.
Step 6
This step is optional. Open the users and groups in the system preferences and click on the lock icon to unlock the settings. In the list of users, there may be some with random names that have been added by the malware. You can remove these users. If you are not sure whether a user is legitimate, do not delete it.
Maybe you are looking for
-
Failed to create the floppy disk to update the BIOS on the Satellite 1800-712
I was given a Satellite 1800 712 with buggy BIOS (power went down while flashing) then now when the laptop is on a sign showsBIOS (Block2) is damaged! (Call the repairman)and so on... I downloaded the latest bios for the laptop, but when I try to fol
-
NEED driver touchpad (laptop VGN - FW 250J)
* Greetings,I had to rebuild my operating system Sony Vaio (VGN - FW computer 250J) laptop,win7/64 upgrade disc (originally used for Windows vista to win7).Fine, except that now I can't DISABLE press ONon the Mouse/touchpad. (Driver = mouclass.sys) C
-
My computer automatically returns to the classic Windows theme.
Whenever I log in, regardless of this theme that I had put my computer, it resets to classic Windows. When I connect, I can change the theme, but the setting remains only until I connect again.
-
I am unable to read the blue ray on my laptop, it says that I need a program to play, where can I find a software to be able to play blue-ray?
-
Best software for a HP PC security?
The day Norton Internet Aureano 2009 60 trial in my Pavilion Slimline already expired so I am shopping for the best security software for my pc. I want something that no man of internet protection, to the protection of the pc, pc maintenance files. I