service host: local service (small network) the use of the high drive
Hello
I reinstalled my laptop to avoid problems. Just after you have reinstalled windows, windows automatically updated install 3 updates. After windows update, service host: local service (small network) is frequently using the high use of the disc... Microsoft, U CREATE DEFECTIVE UPDATES...
Specifications:
Dell Inspiron 3421
4 GB OF RAM
HARD DRIVE 500 GB
Processor Intel Core i5 3317u
In order to diagnose your problem, we need run Windows performance toolkit, the instructions that are in this wiki
Tags: Windows
Similar Questions
-
I want to set up a small network of 3 offices and 1 seat. I wanted to use the cheapest and the best available solution for I came up with the following references
For head office
ASA5510-BUN-K9 ASA 5510 appliance with SW, 5FE, 3DES/AES
For Branches
ASA5505-BUN-K9 ASA 5505 appliance with SW, 10 users, 8 ports, 3DES/AES
I will configure VPN of Site which I am sure will work with this peoperly. The only thing that concerns me, what I can have 2 WAN links on each site so that I will need to set up backup link VPN from Site to Site. If a link fails in the other session VPN resumes and I'm pretty sure that this requires IP SLA. Will I get support IP SLA based this ASA 5505?
Apart from that, now, I'll order a 5505 with a 10 user license. If users in this industry grows at 15, I will be able to upgrade to ASA5505-50-BUN-K9?
Do I need an extra feature to meet my needs?
ASA5505 aura base ip sla.
10 users licenses means that:
In routed mode, hosts inside (business and home VLAN) count to the limit when they communicate with the outside (Internet, VIRTUAL local area network), including when the interior makes a connection to the outside, as well as when the outside connects to the inside. Note that even when outside initiates a connection inside, the external hosts are
not
taken into account in the limit; only inside hosts the County. Also, guests who initiates the traffic between businesses and home are not counted toward the limit. The interface associated with the default route is considered be the external Internet interface. If there is no default route, hosts on all interfaces are taken into account in the limit. In transparent mode, the interface with the smallest number of hosts is taken into account within the limits of the host. Use of the
local-host
command to show the limits of the host.
For a license 10 users, the maximum DHCP Clients is 32. For 50 users, the max. is 128. For unlimited users, Max 250, which is the maximum for other models.
http://www.Cisco.com/en/us/docs/security/ASA/asa84/license/license_management/license.html#wp1491143
So you must license option for 50 or unlimited user count.
---
HTH. Please rate this post if this has been helpful. If it solves your problem, please mark this message as "right answer".
-
Hello
The server has suddenly get high CPU 100% usage contains SVC host.exe and
Mfevtps.exe. There is no other application is running.One of the server became normal but the other server is always the same. What is the issue and how can set is permanently.
Thank you
YasserHi Yasir,
Thanks for posting your query in the Microsoft Community Forums.
The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.
http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer
It will be useful.
Let us know if you encounter problems with Windows in the future. We will be happy to help you.
-
As mentioned above, this is a new system, but with a more older IDE hard drive with windows xp pack 2 service (I think). When you first start, it says that windows is not stopped correctly and asks me to choose whether to start it normally or without failure or last known working configuration. When I choose to start windows normally, it will load up to a point. The screen of Windows Xp will come with the slide bar. It will then restart. When I choose to start in safe mode, a bunch of 32 file system scrolls upwards on the screen. I don't remember if it of normal or not. He takes over in SafeMode but. I went to the event viewer and got the following errors.
Event type: error
Event source: Service Control Manager
Event category: no
Event ID: 7026
Date: 21/01/2011
Duration: 01:18:54
User: n/a
Computer: CLEAR-ZONE of the
Description:
The next (s) starting or starting system could not load:
AFD
Avgldx86
AvgMfx86
Avgtdix
FIPS
IPSec
MRxSmb
NetBIOS
NetBT
Processor
Rdbss
Rdbss
Tcpip
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Event type: error
Event source: Service Control Manager
Event category: no
Event ID: 7001
Date: 21/01/2011
Duration: 01:18:54
User: n/a
Computer: CLEAR-ZONE of the
Description:
The IPSEC Services service depends on the IPSEC driver service which failed to start because of the following error:
A device attached to the system does not work.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Event type: error
Event source: Service Control Manager
Event category: no
Event ID: 7001
Date: 21/01/2011
Duration: 01:18:54
User: n/a
Computer: CLEAR-ZONE of the
Description:
The Hello Service service depends on the service protocol driver TCP/IP which could not start due to the following error:
A device attached to the system does not work.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Event type: error
Event source: Service Control Manager
Event category: no
Event ID: 7001
Date: 21/01/2011
Duration: 01:18:54
User: n/a
Computer: CLEAR-ZONE of the
Description:
TCP/IP NetBIOS assistance service depends on the AFD service which failed to start because of the following error:
A device attached to the system does not work.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Event type: error
Event source: Service Control Manager
Event category: no
Event ID: 7001
Date: 21/01/2011
Duration: 01:18:54
User: n/a
Computer: CLEAR-ZONE of the
Description:
The DNS Client service depends on the service protocol driver TCP/IP which could not start due to the following error:
A device attached to the system does not work.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Event type: error
Event source: Service Control Manager
Event category: no
Event ID: 7001
Date: 21/01/2011
Duration: 01:18:54
User: n/a
Computer: CLEAR-ZONE of the
Description:
The DNS Client service depends on the service protocol driver TCP/IP which could not start due to the following error:
A device attached to the system does not work.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
I did find something online that contains all the system boot or start specific drivers. Windows and harddrive was working in another computer just before he was switched. Let me know if you need other information.
Thank you.
First of all you are missing probably a number of device drivers, particularly the network card driver and the driver of the motherboard. Use your XP disk to perform a repair installation. This should go a long way toward you're going to get. If your new box has a driver disc that should help a lot. You can't port XP perfectly the way you did. It usually requires a repair installation to fix the hardware abstraction layer. Colin Barnhorst
-
Replacing the hard drive on the satellite 1400-103
I try to install my old HDD with the following specifications on the satellite 1400-103
Toshiba
MK4313MAT
HDD2141 L ZEO1 T
DC + 5V 0. 7A
S/N 99014292T 0T 3 EC. A
4327 MO (CYL8944, H15, S63)But it has not been detected, can it be fixed?
TIAHi TIA
I'm a bit confused. Your device comes with 20 GB of HARD drive. Usually, there is problem if someone wants to build in the HARD drive with a much higher capacity. The disc HARDER it who are you talking is just with 4.3 GB. Why you want to use this HARD drive on your device?
My opinion is that if you want to exchange the HARD drive, you must use the same as one with a higher capacity. This small, you can use as disk external DRIVE for backup of data.
-
Hello
I created a WCF Service, customized and hosted locally by using application Console VS.
I need to access the methods of the custom of a custom Page HTML application, using JQuery.
I tested the WebService in Wcftestclient.exe and it works very well.
Now, while trying to access it from the HTML Page (not no matter what Web Application), he runs into function() error of $. ajax()
State of error: 451
messageReason Error: Undefined
Please share your suggesstions how approach when accessing the client HTML Page.
Hello
The question you posted would be better suited in the MSDN Forums; We recommend that you post your question in the MSDN Forums to get help:
http://social.msdn.Microsoft.com/forums/en-us/WCF/threads
Keep us updated on the status of the issue.
-
I tried the direct technical support, but it seemed to have cut. Given that I can no longer connect to the internet on my laptop, I'm with my playstation browser and painfully by typing with the controller.
My probllem.I have an ASUS Intel Core i3 - 2350M CPU @ 2.30 GHZ running Windows 7 home premium. I've selected "Windows Update" in the start menu and proceeded to download and install all updates. Once the updates have been installed, my laptop couldn't detect wireless networks which means that I can't connect to my router and have lost the internet.Device Manager indicates 802.11n Wireless LAN Card is working properly.Windows did create a restore point before installing the updates, but everytime I try a restore I get the following message"System Restore has failed. Your computer's system files and settings were not changedDetailsSystem Restore could not access a file. This is probably because an antivirus program is running on the computer. Temporarily disable your antivirus program and restart System Restore.An unspecified error occurred during the restoration of the system (0x80070005)""I disabled anti Virus AVG and COMODO firewall only to receive the same message, and it now appears that the restore point disappeared as if by magic, saying system restore ' no. restore points were created.Updating installed Windows the followingMicrosoft .NET Framework 4.5 1 4.5.50938Microsoft Office Home and Business 2010...Service Pack 2 for Microsoft Office 2010...Microsoft driver (keyboard) 21/04/2009Microsoft driver (mouse) 21/04/2009Driver Microsoft (System) of 21/06/2009...Microsoft driver (System) 21/06/2006Driver Microsoft (System) of 21/06/2006...RALink Technology, Corp. (Net) 02/04/2013 pilotUpdate for Microsoft WindowsUpdate forUpdate forWell when the restore point was present he says that these things will be deleted that's where I got the list, but as I said the restoration failed and disappeared.I have reset my router but my laptop doesn't detect a network and there are usually 10 in the region and it shows nothing. My router is fine, as I use it now with my playstation.Please I really need help, how do I get my laptop to detect the wireless network. If someone could give me a few steps to do, please.Most laptops have a switch that turns the wifi radio on or off. Often, it is a combination of the Fn key and one of the F keys. It may be a physical switch somewhere on the laptop. See your manual for details.
If this isn't the problem...
What is the brand and model of your router? Almost all wifi routers also have at least one Ethernet port, you can connect your computer to the router with an Ethernet cable and download the right driver for your http://www.asus.com/support wireless card
Have you tried to "Roll back driver" in the "Driver" tab of your adapter wifi 'properties' in Device Manager? At the very least, determine which version of the driver is installed, and compare that to the current version on the asus support site. -
Original title: Shared readers do not reconnect
I have two PCs connected wireless. A laptop (Vista Business) was the drives mapped to actions on the other PC (XP). Whenever the Vista PC is started or out of hibernation, or after only a short period of time these discs are not available. Click on the drive in Explorer to display the message "an error occurred during connection [drive letter]: [share name] Microsoft Windows network: the local device name is already in use." This connection has not been restored. »
If I click on 'Network' within Solution Explorer, the XP PC is not visible. The only way that I can "reconnect" these disks is to go into my anti-virus (Trend) and open the network map. This shows the XP PC and then the shares are available through Explorer - XP PC is still not visible by clicking network however.
It started only happens in the last two months - cannot locate exactly when, but quite recently. I use connections to store small files and backup critical files a few before nailing the laptop away and it is quite annoying to have to go through this routine every time.
Any ideas?
Just in case it helps others - I found that if I make sure that my XP PC has a fixed IP address, and then set up the shares so that they are defined using the IP address and not share names, then I do have more problems - seems like it's something to do with Windows solve the share names rather than something to do with the personal firewall after all.
-
There was a problem with the Hotmail service (a network connectivity problem temporary has nothing to do with your computer). Please try again
. I really need to fix this! Help!original title: no answer not before!track every step!
no change!I am getting really worried about it!Please ask in the forum Hotmail. We do not use it. We cannot answer your question.
Windows Live Solution Center Hotmail Forum
http://windowslivehelp.com/forums.aspx?ProductID=1 -
Hi, I'm trying start the IKE and AUTHOP service from the SERVICES screen but I get this error:
Windows could not start the IKE and Authip IPsec keying service modules on the local computer. Error 1075 the dependency service does not exist or has been marked for deletion.
original title: ike and authip error 1075 the dependency service does not exist or has been marked for deletion
Hello
Remember to make changes to the computer before the show?
You can follow the below methods:
Method 1: Restart Windows and try to start the Security Center service.
If you still receive the same error, make sure that the WMI service is launched and running:
(a) click Start, run , and then type Services.msc
(b) double-click Windows Management Instrumentation
(c) set its startup type to Automatic
(d) click Start to start the service, and then click OK
(e) restart Windows.
Method 2: Restart the service
Windows logs an error if the service IKE and AuthIP IPsec Keying Modules or the driver does not start, or suddenly, they end.
To restart the IKE and AuthIP IPsec Keying Modules service:
To perform this procedure, you must have membership in the local Administrators group, or must you have been delegated the appropriate authority.
(a) restart the service. You can do this from a command prompt or in the snap-snap-in Services Microsoft Management Console (MMC). Do one of the following:
· Start an administrative command prompt. Click Start, click principally made programs, Accessories, right-click guest, and then click run as administrator. At the command prompt, run the command net start ikeext.
· Click Start, type services.msc in the Search box and press ENTER. In the column name of the Services snap-in, right-click on IKE and AuthIP IPsec Keying Modulesand then click Start.
(b) if the attempt to restart the service fails, restart the computer. This forces all related and dependent services to restart.
(c) if the error persists after restarting the computer, then the executable files for the driver or service may be damaged, and the operating system must be reinstalled.
Note:
You can check that the IKE and AuthIP IPsec Keying Modules (IKEEXT) service runs by using the Component Services Microsoft Management Console (MMC) or the net start command line tool.
You can check the link: http://technet.microsoft.com/en-us/library/cc733299 (WS.10) .aspx
Method 3: Run a scan of the System File Checker.
http://support.Microsoft.com/kb/929833
It will be useful.
-
"previous installation of host services has detected the error.
I posted this in the beta forum and not answer. I'll try here... Here is the link to the beta forum: http://communities.vmware.com/thread/278405
Try to uninstall a component, vShield, in this example, the portion of Port Group isolation. I get the following error:
"previous installation of host services has detected the error.
ESXi V4.1
VMkernel is on a dvSwitch
Thank you
Mike
THIS ONLY if APPLIES to vShield Zones / App vShield
One last thing, you mentioned this announcement on the beta site which tells me that you had a pre - GA on areas/App version installed. If that were the case, or maybe a previous installation of App/areas (Beta) had an installation/uninstallation failed, then do this procedure to clean the host of all the previous components.
1. remove the vmservice-vswitch created during installation (assuming that there is no other device that uses this vswitch)
2 remove the address 169.x.x.x, given the Net.DVFilterBindIpAddress of the host property.
Detailed procedure:
1. go through the uninstall process each time as
possible (if one of the components to show as it is installed). Then go to the
next steps.
2. search for the vmservice-vswitch and delete
it. it is a vSwitch without physical adapters service that was created
during the installation. It will have 2 groups of ports, one called
vmservice-vmknic-pg and the other vmservice vsheild pg.
3. Select the ESX host on the left hand side
tree on the right hand click the Configuration tab pane and click
Advanced settings of the software. In the Advaced search page settings
the Net section, then select it. Scroll through all the
way down and then make your way up until you find
Net.DVFilterBindIpAddress = 169.254.1.1. Remove the 169.254.1.1 and
Click OK.
4. installation of APP vShield vShield Zones should now work.
-
Why is my "files and folders" service unavailable when I use the glance
I did a service simple automator to open a file in Photoshop. I gave her the ctrl-opt-S shortcut in the keyboard for easy access preferences. I can now open images in Photoshop with a simple keystroke. It works, most of the time, and I noticed earlier why sometimes it is not. When that I view an image in the finder with peek, the service is not available, even in the menu. I just press the space bar to get out of the eye then I can reuse the service.
This seems ridiculous because the file is certainly always selected in finder. Up and down arrows change the selection, but I can't use my service on the currently selected item in finder. I just need the services available for the glance.
What can I do to make this happen?
Hello
So far I have tested under OS X 10.6.8 I do the service do not receive any system file objects in any application in order to make it accessible all at glance is active in the Finder. I don't know, but I guess that's a limitation specific to Automator services.
A simple solution is to make the service receive no entry in any application and get the file Finder selection system objects. Using something like the action run the following AppleScript.
The service properties:
- Service receives [no input] in [any application] - [not] Replaces selected text
Run AppleScript Action:
on run argv tell application "Finder" open selection end tell end run
For example,.
In my brief tests under OS X 10.6.8 I can invoke this service via hotkey designated while running a quick look in Finder even in its preview mode full-screen.
Good luck
H
-
Regularly receive some 'No. Service' indicator in the signal area hard. Only cure is to reboot the device. So seeing service will show the power of the full signal. When 'No. Service' of course I don't get any calls or messages. Very frustrating to ordinary, look at my phone to see if I have the service even though I know the signal is strong. Is this a known issue? No problems apart from a revision permanently and restart when 'no Service '. BTW, my android friends have no such issue when socialize us physically together. My iPhone is now the target of many jokes. Not funny for me.
Hello! Have you tried the following?
Try resetting your device. This will not erase your data stored on that device.
- Press and hold the sleep/wake button
- Press and hold the Home button
- Press and hold both buttons until the display turns off and on again with the Apple logo on the subject.
Alternatively, you can go to settings - general - reset - Reset all settings
If that doesn't work, restore your device to factory settings. Please note that this will delete the data on your device.
Take a look this Apple Support article: use iTunes to restore the iPhone, iPad or iPod to factory settings - Apple Support.
As a final step, try recovery mode. Turn off your unit, then plug it to your computer with the hold home button. Hold down Home button until you see the logo of iTunes on the screen of your device. After that on your computer, you should see the iTunes window saying that your device needs to be restored to factory settings. Click Restore.
More info here:
https://support.Apple.com/en-us/HT201263
If these steps do not work, contact Apple and ask for help. Maybe it's a hardware problem (for example, with the antenna etc.).
-
Could not start the time service windows on the local computer 2 error
Cannot update the system clock of time Internet.After double click to display the time in the taskbar, the Date and time properties window appears.
Then I time tab-click Internet, and then click Update now - this produces the following message..."Year error occurred getting the status of the last synchronization." The RPC server is unavailable ".Then I clicked on start > Control Panel > Administrative Services > Services > time WindowsI click Start the service and get the following message..."Could not start the time service windows on local computer.""error 2: the system cannot find the file specified."Help! What now?Hello
Glad to know that the problem has been resolved. If you have additional questions on the computer, please ask your question about Windows and we will be happy to help you.
-
I have a laptop asus F5R model. I use the operating system to windows xp service pack 2, I can't install the audio driver on my knees, please help me
Download and install the last set of drivers (starting with the chipset / driver motherboard) to the ASUS support site: http://support.asus.com/download/options.aspx?SLanguage=en&type=1
J W Stuart: http://www.pagestart.com
Maybe you are looking for
-
A Japanese dictionary will be available anytime soon?
I live in the Japan and could really use a Japanese dictionary
-
Install of Win7 64 bit on Tecra M10 - 11V
I have to update the Bios before a clean install of Win7 64 bit on my Tecra M10 - 11V? Should I regularly check and update the Bios? After installation the program "Toshiba Software Installer for Windows 7" find and update all the drivers and the nec
-
After a reinstall of windows 7 I don't have the drivers to connect to the internet. My model is p2-1123w. Thanks for the help
-
Outlook Express e-mail problem
I use Outlook Express V6 and when I send an email with an attachment to the recipient gets gobble-di-gooke! Can anyone help please?
-
Slow PC, I want to remove the 2nd account but how?
my pc can run very slowly because of the guest account