Set knop body IK I of zijkolom met bladwijzers kon openen en Pickwick.

Similar Questions

• USB6120 as meter of thermocouple

  Anyone know anyway I can set up a USB-6120 as a meter of thermocouple in place measure voltage?  I have a few extra analog inputs on the device I want to use for this purpose, so I don't have to buy a whole new data acquisition.  Anyone have any ideas?  Is this possible?

  I guess you meant USB-6210... Everything depends on the desired degree of precision... You will meet 2 limiting factors:

  -noise DAQ of entry card: M-series cards usually have pretty good performance, without signal conditioning, you can already reach noise measurements less than 1 ° C, with the more sentitive input range (we did this on a project for a client). But to be very careful in your wiring, sampling frequency (higher), with an average of signal, etc. To get better, you will definitely need additional electronic (preamplifier and a lowpass filter anti-aliasing with cut up to half of your actual sampling frequency). You will find screws to convert the voltage measured temperature in the digital palette (Scaling).

  -compensation of welding cold temperature: thermocouple, thus not only measure the temperature at their "end of remote sensing" (the junction of the thermocouple), but are also influenced by the junction of the thermocouple wires (made of some specific materials according to type of transport CANADA) with the connection of the side block DAQ board of copper. To compensate for the parasitic portion of the signal, you need to measure the temperature of the block connector (for example with an RTD, so you do really need one more Ain chanel) and fix the total voltage for the thermocouple voltage provided at this temperature. All this is done automatically when you use OR packaging, specially designed for the connection of thermocouple signals. But if you have a "precise reasonnably guess" (regarding your needs of precision) of your connector block temperature, the conversion V T screws allow you to specify its value. To first order (that is, if one ignores the linearity no thermocouple), the overall error will equal the error in your estimate of the temperature to the connection block. Not really suitable for precise (1 ° or less) the measures, but OK if you measure an oven at high temperature +/-10 ° C...

  I hope this helps.

  Vincent

• Hello! Size of body text.) in sections B.) menu responsive mobile - tablet & mobile problem

  Hey! I have 2 quick questions for THIS

  Question-TABLETS

  • When I set the body of the text, it seems that affect the first header. If you pull up on a shelf, you can see on the page of log book - the background contained is 'bloating', I believe, to contain the text. I just need to get the smaller text; that the word "Synopsis" seems to be affected by the definition of font size of body.

  Question B - MOBILE

  • Nancy O. SO generously helped me with a sensitive menu for mobile, but it does not fit on the top of the screen. Can we quickly see where I would resize to fit the screen?

  Thanks a lot to all

  Mine is tested & works on Android Smartphone, iPad area and workstations.  See screenshots.

  

  

  You have added jQuery or the script code & MeanMenu function to your documents.  That's why your menu is unresponsive to mobile devices.

  Nancy O.

• Position of the body of model 1,2,3 page to the left of the page

  Hello
  
  How can I make a default page template.
  
  The situation is that I have a theme that has a default page template the value so that the ' Page Template body 2' comes to the Centre (let's this theme - theme 1).» But there is another theme that gives me the possibility of
  
  set the "body of model 2' to the left of the page the page (theme 2). I thought to change the theme, but my other report parameter will go for the draw. Then I copied the default template for the page of theme 2 theme 1, but I
  
  Cannot make the default page template. How can he make the default page template?
  
  Is there any other way to do so cela "model Page body 2"appears on the left.
  
  Thank you
  Rakesh

  In Application Designer:
  -Change the Application
  -Click on shared components
  -Click themes
  > The current theme will have an "asterisk" (*) by the name of the theme
  -DO NOT CLICK ON THE THEME
  -On the right column will be a group called tasks
  -Click change the theme
  -Click on your current theme

  You will see a drop down menu which allows to choose the default page template.

  Hope that helps.

• Mail send and the body of the email and the attachment to ATG.

  Hi all
  
  Can any body explain to me how I will send an email with the body of the email and attachments in ATG.
  
  Thank you
  Chadnra mohan

  You can use atg.service.email.MimeMessageUtils or javax.mail.internet.MimeMessage (both are under Message classes).

  You can set the body to aid below extracted.

  Message MSG = MimeMessageUtils.createMessage ();
  msg.setText ("your body of the email");

  You can define the setting and the content using below extracts.

  define the content of the message: message to multiple parties + attachment
  ContentPart happy [] =
  {New ContentPart ("it's clear","text/plain" ""),}
  {New ContentPart ("this is text html" , "text/html")};
  Attachment of files = new File ("attachment.html");
  MimeMessageUtils.setContent (msg, content, seizure, false);

  All of these are clearly explained in the link below.

  http://docs.Oracle.com/CD/E24152_01/platform.10-1/ATGPlatformProgGuide/HTML/s1013creatingjavamailmessages01.html

  Thank you
  Gopinath Ramasamy

• Incorporating animations of edge in Joomla: < body > tags?

  I'm working on the incorporation of the edge entertainment in Joomla, (without the use of iframes) should not be so difficult, at least in theory.

  I have successfully incorporated the code of edge in a Joomla! article and a check of the resulting web page shows all Javascript files load and do not generate errors. When I load the page, the animation works! So my workflow is correct, what is the dipping.

  A small problem. Edge, by default, writes a pair of < body > tags around the animation, which creates havoc on the web page, as it is, of course, an existing set of < body > tags and adding a second series up the entire page in the structural chaos.

  Can anyone suggest the best way to remove this part of the JS the edge of the output files? I'm not enough of a JS coder to see the obvious solution here.

  Once this small problem, it's resolved, I'll post the entire procedure for the coating of the animations of edge in Joomla articles, something I just summarized in a previous post.

  TIA!

  Thanks for your note, Elaine. I have used these tools to browser for years.

  I solved the problem! I usually test enough before I post a quesiton like this, but I missed a typo in of code stupid enough that I had done.

  I can tell you now that there is absolutely NO problem incorporating animations of edge in a 3.x for Joomla article. The small amount of "circumvention" required is simple enough, but certainly not as easy as a Flash SWF file in such an article.

  I have some experiences more to do with animations of edge in layers and then I'l pst the workflow here.

• Email - the message body of the formatting of bursting

  Hello
  
  I'm working on a breaking email delivery control file, but have a problem with setting shaped body "e-mail." It is always in text format - does not recognize the html format. I first thought it's just my vision of the configuration, but find that it does not also other e-mail providers (yahoo, google, etc.).
  
  Kindly share your habits of formatting of the message body in the breaking control file. I use EBS 11.5.10.2 (XML Publisher 5.6.3).
  
  Thanks in advance.

  I think it will work for you, use html for the body within CDATA.

  
       
  
  
       
                 
                 

  Please find attached Pick slip number ${PICK_SLIP_NUMBER}.

  
                 

  
  Kind regards
                 Company
  Address1
  Address2
  Phone: 123-456-7890
  Fax: 123-456-7890
                 

  
            
       ]]>
  
  
  
  
  
  
  
  
  

• Copier E - studio 212 is still show me "Toner is low.

  HelloW everyone

  first of all I'm sorry if I posted my question in a wrong section,
  I * E-studio 212 Copier * always show * toner is low * even though I set a new.

  I first met another error "toner is not recognized" that was the right one for my machine "T - 1810 / D - 5 K

  How can I correct or erase the message "toner low" and "toner is not recognized.

  any replay or help would be very appreciated

  Welcome to the community of use-user of Toshiba. I m scared in this forum you will not find many reviews on printers because this forum was created especially for the laptop computer and multimedia products.

  However, according to various sources that I found in the internet, this message is displayed because the toner is empty. If you have installed new toner and this message always, then probably the installed toner was not original or compatible part.

  If everything is OK, but the message is still appear, then you could erase that going:

  Function of the user--> user--> General--> Toner near detection empty--> Yes

  By the way: the user manual here:
  http://www.Eid.Toshiba.com.au/customers/c_es182_242/e-Studio%20182-212-242_OM_EN_Ver01.PDF

• Need a new acquisition of data USB multifunction device

  Hello

  Currently I use a PCIe - 6321 Multifunction DAQ hardware to control my stepper motor. I need to change the PCIe - 6321 and use the engine with a device for the acquisition of data USB multifunction bit PCIe - 6321. I'm not sure which USB model to select. Can I please get help about the choice of the right MIO USB data acquisition device that works similar to the PCIe - 6321.

  Thank you

  Bharath J S

  The 6212 differs from the 6321 somewhat on the digital side, which probably you use to control your stepper motor.  For example, it was only software DIO timed tasks and has only 2 counters with a set of features (e.g. no output meter in the buffer).

  Best regards

• Appellant States in a state machine more than once

  Hello again,

  Is there a way to call a State in a state machine after that he ran already? In order to develop, I have a program that will put pressure in increments of 20% and will then write to a file. Once it is done with the rule of higher pressure (100%), I want it repeated the test, but this time in decrements of 20%. So it will do:

  1. set the pressure at the lowest point

  2 meter to read and write the value

  3. set the pressure at 20%

  4 meter to read and write the value

  All the way up to 100%, then:

  5. set the pressure to 80%

  6 meter to read and write the value

  7. set the pressure at 60%

  8 meter to read and write the value

  All the way to the lowest point.

  Is there a way to do so instead of making a State for reading and writing to each percentage? In this way I haven't read Agilent 20% increment, Agilent read 40% increment, etc..

  I have attached the code to explain what I mean.

  Thank you all, still a newbie

  
  

• Manual adjustment of the speedlite 600Ex-RT

  Can you get it someone please let me know if it is possible to the timeout value between f to get a distance to correct for speedlite 600EX-RT exposure is set in manual mode without using the meter. The flash output is selected for exposure in manual mode. How to check that the selected power is also suitable for the exhibition.

  Thanks John.

• Structure of the event: problem with data transfer

  Hello everyone,

  for three days I'm troubleshooting an issue in LabView with the event structures. I really hope someone can help here, because I can't find anything on the entire WEB.

  I had six groups of equal to a VI entry, each containing five checks enum (among others) where the user can specify some configuration of measurement data. I want the program to do is: to recognize if a any of these enum values has been changed and if yes, then submit the values containing the cluster in a subvi then calculates the wiring and affect the material of the ports. In addition, i need to submit the number of the enum element that was changed, so the program is able to clear the user input in the case of a breach (e.g. If the user sets two entries of enum control 1 meter and 2 Group 1 and then tries to set a third counter of entry to port 3, the program displays a message and deletes third entry as the number of entries of counter is limited to 2 per cluster).

  To resolve this problem, I used a structure of the event with 6 x 5 cases (change of enum value 1 Group 1 Group 1 enum value 2 change... and so on until the change in the value enum 5 Group 6).

  

  The problem is that if the user changes a value, the event structure reacts and performs the proper case; However VALUES of the cluster, the user changed are not subject to the SECOND time that an event occurs. It is a kind of a situation, "n-1". For example, if all five controls Enum of Group 1 are 'disabled' first and the user sets enum 3 of 'Meter entry', the structure of the event runs but submits the values previous to the Subvi (all enums 'Disabled'). When the user makes the second change, say that enum SWITCH1 to "Analog Input", the structure of the event is running again and passes the values of the FIRST user to the Subvi editing, then the Subvi gets data "enum 3 meter inlet and all other disabled enumerations.

  In easier words: if I have new values on my cluster "Kanal 1" (left side of the screenshot) and run the structure of the event, on the right side to "Kanal 1" indicator, I get the previous values (n-1).

  The structure of my event is in a while loop. If I create a timeout every 10 ms, and a loop of 250 ms the waiting time, I got the 80% chance that the recent changes are transferred to the Subvi correctly, in other cases I have a delay of the 1 step as described above. It seems to be directly based on the time that I specify the while to wait - but I can't explain it and I cannot accept a less than 100% chance to transfer the correct data, nor can I accept delays of a few seconds for each loop run. If I indicate timeout (infinite) get delayed 1-1 step values in all cases.

  When I specify cases of event to react on "all items value change" of the structure of the event behaves properly - but then I can't handle indicate which element has changed, as the CtlRef of output in case of a structure does not specify "enum 1, enum 2..." but only "Group 1".

  Does anyone have a solution to this? It is certainly a problem with the structure of the event, but I can't understand what to change.

  Thank you much in advance,

  Mr. Boiger

  This is because the terminal is read until the structure of the event runs.   Terminal is read, the event structure is waiting for an event.  The change in value.  Business events are running, but the value is the old value.

  Put the terminal inside the event.

  Or, you can display the connector called "New value" on the side left (stretching down from the border of the node 'CtrRef').  Use a wire one to come.

• Canon at the end of photo booth

  I just bought a Mojo photo booth and I am very new to photography, so please forgive me if I ask stupid questions. I'm having a problem with some pics to come out too dark.

  With the help of a green background on the stand (stand 5' x 5') sometimes the topic turns into a ghost and dark areas disappear in the background image. The problem is worse if the subject is wearing light/white or holding a large white prop (Santa beard, bubble of text, etc.).  I was told the problem was not enough light and that I should not use the Auto mode. I set the camera manual and used the suggested settings (F8, ISO 200, 1/160 ss). I don't have an external flash, just the flash that comes with the camera. If the subject is not white, the pictures come out fine - the canvas background Green is well lit and the décor digital image looks good - no ghost delivers. Using the same settings but changing a white shirt causes the wallpaper green to appear darker and the subject to look like a ghost. I changed the setting of the average E - TTL II meter and it solved the problem of the white shirt... until I added still more white on the frame, then the issue of Ghost is back.

  I have this same problem using only does not the green screen. If the there are a lot of white in the cabin, or glasses reflecting large prop, the picture comes out very dark (even in Auto mode).

  I went to a photo shop today and spoke to the owner. He said that if the device is in manual mode, then the setting of the meter should not affect the photo. He must only tell me if/how much my exhibition will be broken, he said. This isn't the case, though - looking at pictures side by side, it is clear that the white-shirt photos have a much darker green screen behind the subject. So, manual mode should replace the functionality of meter the camera store owner says? And if so, that means that there is something wrong with my camera? Or is it a setting I'm missing?

  Thanks for any help.

  Ginacresse wrote:

  Thanks Bob. I found the setting on the camera, but it is grayed out and I can't access it. It seems that I have to use a wireless flash in order to activate this setting, but I have no other than the built-in external flash devices. I anticipate getting some kind of external flash over the weekend to see if I can solve my problem of ghost. Do you have recommendations for the genre should I get? What I have read, I need something that can be set to manual and I can control the flash output, i.e. full power, power 1/2, 1/4 power, etc. I only know more about it.

  Canon's Speedlite flashes are very good, and of course they would communicate reliable with your camera. But they tend to be expensive; the top-of-the-line model costs more than $600. There are one or two Chinese companies that make lightning that are much cheaper, and some in this forum swear by them. But I have no experience with them and would not have dared try to recommend one for your application.

  Skirball is our resident expert flash, but I have not seen something from her for a few days and suspect she may be away for the holidays. If you can wait until she gets back online, I'm sure it could give you some good advice. There are others who are also familiar.

  Flash is a complex subject, and a beginner is likely to find he's going to be rough. But we have to start somewhere: the only way to get over this one is starting to gain experience.

• How to call Mail?

  How to set subject, body, attachment to InvokeRequest for sending Mail?

  InvokeManager invokeManager;
  Application of InvokeRequest;
  request.setTarget ("sys.pim.uib.email.hybridcomposer");
  request.setAction ("bb.action.SHARE");
  request.setMimeType("text/plain");

  None of those who illustrate the OP really do with an attachment.

  Note that (before at least 10.2) it was not possible to do in QML, despite the implication apparent docs Kareem links on the page above.

  Shadid has shown the only (?) way known to pre-populate the header fields AND include an attachment in this post: http://supportforums.blackberry.com/t5/Native-Development/Invoke-Email-with-Attachment/m-p/2251453#M... (and you have to do from C++).

• A Contact button

  Hello

  I made a contact us button to send feedback by writing to us. But mail is sent in the background without showing the e-mail screen.

  All advice will be a great help!

  ...

  Download the mail by default Session store.

  Store is Session.getDefaultInstance () .getStore ();.

  retrieve the sent folder

  Records file [] = store.list (Folder.SENT);

  Folder sentfolder = files [0];

  Create a new message and store it in the sent folder

  Message msg = new Message (sentfolder);

  Address [] recipients = new address [1];

  try {}

  beneficiaries [0] = new address ("[email protected]", "[email protected]");

  Add the list of recipients to the message

  msg.addRecipients (Message.RecipientType.TO, beneficiaries);

  the value of an object to the message

  msg.setSubject ("I have a problem");

  sets the body of the message

  msg.setContent ("Initial Device Info :");

  sets the priority

  msg.setPriority (Message.Priority.HIGH);

  Send the message

  Transport.Send (MSG);

  A session = Session.getDefaultInstance ();

  Transport transport = session.getTransport ();

  transport. Send (MSG);

  } catch (Exception me) {}

  System.Err.println (me);

  }

  Invoke.invokeApplication(Invoke.APP_TYPE_MESSAGES, new MessageArguments(m));
  

  use it in case you want to call the native application for email