Need a new acquisition of data USB multifunction device

Similar Questions

• Looking for a way to mount an acquisition of data USB-6008

  Anyone has a suggestion for an acquisition of data USB-6008 mounted on a Panel. I use it for a system where it should not be loose. I have a few ideas, but hope that someone smarter already has a good solution.

  Thank you

  It is not a robust application, but the box will be moved and I don't want it put in the open air. I simply put a velcro pad on the back and the atttaching in this way. Should be all I need.

• Generation and acquisition at the same time, acquisition of data USB-6356

  Hello

  I have a VI how is able to read entries with a USB DAQ-6356 and I use a generator of signals 'Agilent 33522 A '. I want to generate and acquire with the acquisition of data.

  In fact it works but not well, the frequency is not very stable and does not stop the 2nd loop with 1 (2nd is generating, 1 is Acquire).

  Thanks in advance

  P.S my VI isn't a state machine true because I need to fight against it at the moment.

  OK, so you're at 3 ms/s in writing and reading at 1.25Ms / sec and you wonder why he has a little difference in the frequency set?  Ideally, you want to read and write to share a sample clock but by selecting at least the same frequency clock (or one that is one multiple of the other) would go a long way to fixing this source of your error.

  The second source of error: you generate a contineous waveform.  unless you select 'whole number of cycles' there is a discontinuity when the end is reached at an arbitrary phase and the phase is reset to zero at the beginning of the wave.  DAQ assistant writing can "Use Waveform Timing" to adapt its sync settings to the dt waveform and the number of samples.

• Communication problem between LabView and acquisition of data USB 6259

  I want to monitor a data USB-6259 acquisition using LabVIEW 8.6. However, when you try to create an explicit task (using the DAQ assistant) in order to acquire a signal, I get the message asked supported device found¨. I can see the USB-6259 under ¨Devices and interfaces¨ to the MAX, but when I try to import the configuration data for NOR-DAQmx 8.7.2 in MAX, I get the message ¨Can´t import file configData.nce.  File not found¨. I use NEITHER-DAQmx 8.7.2.  Any suggestions?

  Corneliu

  Hi, Corneliu,

  This question could be generated due to a corruption of database of MAX. Here is a link to restore the database to the MAX.

  http://digital.NI.com/public.nsf/allkb/2C7480E856987FFF862573AE005AB0D9?OpenDocument

  Just follow the steps and let me know if that solves the problem.

  A greeting.

  Jesus.

• Sampling frequency for the output of an acquisition of data USB-6211 card?

  Hello-

  I use a CGI CMOS FireWire camera to read an interference figure, then using a transformed of Fourier transform spectral interferometery (FTSI) phase recovery simple algorithm to detect the relative phase between the successive shots.  My camera has a linear 28 kHz scan rate, and I programmed my phase retrieval algorithm take ms ~0.7 (of a trigger of camera at the exit of the phase). I use the live signal to control a piezoelectric stack, by sending a voltage single sample to the analog output of a data USB-6211 acquisition card.

  Send this output voltage increases the time of my loop 4 m, I would really like to achieve a 1 kHz or better sampling rate. Is the problem with my DAQ card or with the processor in my computer? The DAQ cards of NOR can support these speeds?

  Thank you

  -Mike Chini

  Hey Mike,

  With USB, your loop rate will be around or under 1 kHz, even on the best of the systems. USB has a higher latency and less determism PCI and PCIe. You can get rates AO one much better sample on a PCI card, potentially a PCI-6221. We have a few HAVE points of reference for targets of RT for PCI, / AO in a loop, you should be able to get similar performance in Windows, but if you do a lot other treatments may suffer from your local loop rates.

  Hope this helps,

  Andrew S

• How to reduce the noise in an acquisition of data USB-6251

  Hello world!!!

  I have a few questions about a system that I have developed using a data acquisition OR usb card 6251. The pressure control system.

  First of all, the signals are acquired using an Omegadyne pressure transducer. (Typically, the signals are between 0.1 mV and 38 mV, pressure is between 0 to 50 lb/PO2). The transducer is connected to the usb-6251 daq card (I use pinout of the 1 and 2 for the signal acquisition, also, I have a 100 K resistor between pin 2 and 3) and the card is connected directly to the computer. In addition, I have an omega counter, I use it only to see pressure on the screen. But long term, it will be useless.

  One of the problems I have found is the noise, the measured voltage values change much. Even if the figures in the player screen do not change so much... (or do not change)
  The system should regulate the pressure so if every second it changes a lot, the system did not work properly. How can I make the technical more similar to that of the meter? In the labview program that I use, I use a block 'base DC', he reduced noisy signals a lot, but not enough that experience, I need more stable values.

  Thank you

  I don't mean in the /manuals of broaching and do not open .doc from unknown sources files (a chart single .png is fine ;-))

  However, I guess you already measured in differential mode and the 100 k is a path for the currents of polarization forever

  The reason why your counter is stable can be the fact, that she has a generation to filter low pass (on average) with a big enough constant time.

  First things to do:

  You did it that there is a filter anti-aliasing suitable for your sampling rate?

  Read the signal on at least 100 ms (120ms in line 60 Hz) possible higher sampling rate and take a look at the signal (and display a chart as a .png or .jpg image)

  This will give you an idea how the signal looks the same. Then you can choose a filter according to your system and the signal or other investigations to do not even catch the noise (groundloops, protection...)

  You can use an example on the screws or the testpanel to the MAX for this measure.  (Personally, I prefer a similar scope :-))

• temperature sensor with the acquisition of data usb-6009

  Greeting

  I want to use a sensor with usb-6009 to save the variation of body temperature about 15 minutes and then use these data in labview.

  If you please you can advise me with the best low-cost use and the way/circuit sensor connect it to the usb-6009.

  Hi ba7soun,

  If you can use with USB-6009 LM35 depends on the range of output voltage of the sensor. I understand that it requires a 5V supply with respect to the ground, which you can provide to the USB-6009 (more than 200 my should not come from the USB-6009).

  The maximum range of the USB-6009 is - 10V to + 10V, while the minimum range is - 1V to + 1V, also probably the output signal of the LM35 will be in this range. What you need to do is to compare the full range of the output signal with the range of the DAQ divided by 2exp (14) (because it is a 14 bit ADC) and ensure that the first is much more than the latter.

  Kind regards

  Condette Dhruv.

• Sampling frequency for two different routes for acquisition of data USB-6009

  Hello

  I use a box USB-6009 and incorporating the "daq assistant" to change the sampling frequency.  I'm trying to find a way to set the sampling frequency to two unique values for the two separate channels.  I tried implementing two assistants daq and different for each channel sampling frequency setting, although it does not work.  Is it possible to set the sampling frequency for all channels, and then reduce the rate for another channel - or an alternative?  I would be recognizing any input on this matter, thank you!

  -Anthony

  All tasks on a DAQ card using the sample clock should use the same clock.  Therefore, you cannot have two tasks on the same sample of DAQ card at different rates.

  Alternatives would be:

  1. to combine all channels in a single task and to accept additional data

  2 get an additional DAQ card to use at the same time

• About precision of analog input of acquisition of data USB-6009

  Hello

  I have a problem where I'm reading a temperature signal (10mV / ° c) using the USB-6009 case, but a problem of accuracy of the input signal of the DAQ hardware.  The temperature at room temperature reads at a constant 230mV (23degC) using a multimeter device, but with the DAQ hardware, I see the signal bouncing around to 25mV, + effects greatly my work.

  I was hoping someone might have a solution to this as my brief search forums nothing have mounted.  Is there a way to average this broad band to the extent of the input signal or from resovle anyway?

  Hi mdzz,

  What development environment do you use?

  Here is an example of LabVIEW that should do what you need.

• Acquisition of data USB-6008 not detected in LabVIEW

  Hello

  So my USB-6008 DAQ hardware is not available when I do a new task DAQmx (or open the DAQ assistant).

  I found this link: http://digital.ni.com/public.nsf/allkb/179BC9B0266168288625722100738C22
  I did everything just said but LV still does not detect my USB-6008.

  As you can see on the image below it is detected by the solution of measurement and Automation Explorer. I don't know how to test with visa test Panel.

  

  After that, I tried to test with the diagnostic utility, and here it does not appear in the list.

  I downloaded the appropriate (several times) drivers but still nothing.

  Can someone help me with this?

  
  

• Linux drivers for the acquisition of data USB-6229

  I would use a USB-6229 with Linux and support driver selection guide said that this model is not supported.  However, the 6218 and others are supported.  Is it possible to use 3. 5B pilot defined for a USB-6229 with reduced functionality?  Is it possible, with some basic Linux knowledge codification driver of change 3. 5 b drivers to work with a USB-6229?

  Kind regards

  Craig

  Hi Craig,.

  That is right.

  Best,

• acquisition of data usb-6009

  Hello

  I installed the NOR-DAQmx driver to operate the USB-6009 module.

  The device is well recognized by NOR-DAQmx devices basis as well as by MAX V3.1 as Dev1.

  Yet, impossible to create a virtual channel with MAX, and cannot create a task with NOR-DAQmx Base Task Configuration Utility: Dev1 does not appear in the device drop-down list.

  The Green LED on the USB-6009 en permanence module flashes.

  What do I do? Did I miss something selected in the installation, already redone 3 times on different PC running XP Pro SP3

  Thank you

  It would seem that you have a Daqmx driver problem, I invite you to download the latest version at this address:

  NOR-DAQmx 9.0.2 - Windows 2000/7 x 64/7/Vista x 64/Vista/XP

  Kind regards

• measurement of voltage battery pinout 1.5 V AAA DC with acquisition of data USB-6009

  Hello, I have a very basic question with pinout when measuring 1.5 V voltage on a USB DAQ 6009, using an AAA battery. Is it okay to connect (+) to AI0 and (-) to such AI4 suggested in MAX?

  Nothing else required?

  (attached pinout)

  Thank you

  Hi feanorou,

  Yes, you have the Terminal configuration as award-winning, then using the 0 pine as AI (GOT 0 +) and using PIN 4 HAVE (I - 0) is a good setup for measuring the AAA battery.

• Acquisition of data reading zero intermittently

  I use 3 analog inputs of an acquisition of data USB-6009 to monitor and record the temperatures of my system.  This running VI constantly perform 1 read per second and periodically saving the values drop.  Everything works very well for a few weeks or even months, until that data acquisition shows suddenly have a value of zero.  unpluging the acquisition of data and by him plugging back in solves the problem.  Therefore, I assume that this is due to the DAQ or maybe the USB communication being refreshed power cycle that I get the correct values again.  Any ideas on how to test for the cause of this problem or preventive measures, can I take?

  I was the closing of thought and could help restore communication at the end of each day.

  Oh, and I'm using LabVIEW 2010 on Windows 7.

  Disable the 'power save feature' Windows 7 where it randomly disables your USB hub.  Go to Device Manager and go to USB hubs then the power settings.

• Acquisition of data NOR usb 6008: a strange problem: mxwcgoutrunsilent.VI is not respected

  Expensive OR

  Today, I bought an acquisition of data NOR usb 6008

  and I'm using labview in 2011
  the problem is appear when after I end the process of configuration of the i/o data acquisition Wizard

  the following image shows the mxwcgoutrunsilent.VI is ignored and an error has occurred

  

  someone can help provide this VI for me

  What is the complete labview modules can also so I could do a real time data acquisition

  Best regards

  mangood,

  You received an error code? If so, what is it? What version of NOR-DAQmx driver you have installed? It seems your driver potentially incorrectly installed, and you may need to reinstall the driver.

  Here is the link to the latest version of the NOR-DAQmx driver: http://www.ni.com/download/ni-daqmx-9.8/4297/en/