Setting up multihomed PowerEdge 2900 for the fault tolerance
I try to configure a PowerEdge 2900 server with two network cards on the same subnet-tolerant, but cannot find a way to do it properly. I found this:
http://support.Microsoft.com/kb/175767/en-us/
who says:
"Some manufacturers are tolerant network adapters to guard against a single point of failure. These adapters enable two adapters to be placed in the same server, but only allow the use of an adapter at the same time. If the primary card fails, the driver disables the first card and activates the second with the same address configuration. The end result is a pretty seamless transition to the replacement adapter. This is the preferred method to guard against a single NIC as a single point of failure. »
That it applies to PowerEdge or is there another way to set it up?
Thank you.
Paul
Tags: Dell Servers
Similar Questions
-
Hello
I try to activate FT on a virtual machine that AFAIK ticked all the boxes for FT but I get this message when activating it. No clue as to what might happen or where to connect for extended information? This error message is too generic...
Thanks in advance mates.
Did you follow KB1019165-fault tolerant to fails to 42% with the error: not supported configuration of virtual machines for the fault tolerance
André
-
Cannot access the fault tolerance Mode
Dear all,
I have a problem, which allows VMware ft. I have 2 IBM eServer HS12 blade with IntelCore 2 Duo E6305 CPU @ 1.86 GHz
When I turn on the machine virtual of FT it gives the following error.
Recording/playback is supported for VMS 64-bit only on some processors. Abandonment of record/replay. Unable to access the mode for fault tolerance.
Are there settings that I need to do on the host VMware ESX or VM.
Kind regards
Rahiz
Rahiz,
According to the Knowledge Base the CPU is not supported for the fault tolerance
.
Take a look at the Article KB 1008027 - processors and operating systems that support VMware Fault Tolerance
André
-
Hello
I would like to know how to set up a personalized message for the prevention of the installation of the software via group policy in windows server 2012 R2.
I released some software in my field to a distribution point and I of installation for few of them software restriction policies. But I don't want the default next message below:
"The system administrator has set policies to prevent this installation." This installation is forbidden by system policy. Contact your system administrator. »
Instead, I would like to set up a custom message. Please tell us how can I do same by using Group Policy, if not available, what are the alternatives that I can use.
This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)* -
FTP problem
I set up ftp in iis for the file transfer. On the pc that I am currently in place I cannot transfer files to it via ftp. He says that the password is not accepted. When I look in the properties of the default ftp sites ftp I noticed that the Directory Security tab is not there as on the other pc. How to return this tab or is it the windows software that's not fair. I am running windows XP 2002 SP2 on it and I've updated to SP3. I have no idea.Hello
I suggest you to send your query to the link for assistance.
-
ORA-13754: 'SQL Tuning Set' 'string' does not exist for the user "sysman."
ORA-13754: 'SQL Tuning Set' 'string' does not exist for the user "sysman."
Hello
in 10g R2 when I run the following in isqlplus I error of the United Nations:
No problem if I run it as sys to sqlplus.SELECT * FROM TABLE(DBMS_SQLTUNE.SELECT_SQLSET( 'my_sql_tuning_set', '(disk_reads/buffer_gets) >= 0.05')); ORA-13754: "SQL Tuning Set"'my_sql_tuning_set" does not exist for user "sysman".
Thanks for the help.
How to activate for sys isqlplus?You are logged in as sysman,
Check the user from the sql prompt.
show user
-
Set a static IP address for the printer
One of the most common steps given when members of the community have printers that will remain not connected is affecting the camera a static IP address. Most of the members to respond to messages will include a document that's going to work on the steps and it is very useful. I found a video which will also show you this process on a printer Photosmart 7510.
It will go well to enter the IP address of the printer in the web browser and access the built-in web server (EWS). Once in SAP, it shows the path to take to set the static IP address for the printer. I thought it would be a good video to share with the community so that there is assistance available for those of us who are visual learners. Here's the video promised on the static IP address.
I hope this helps the community. Good impression to everyone!
-
Hello.
I have a document with some parties updated with the fusion of data (via placeholders). Is it possible to set a style of different cases for the same placeholder in the same text. See the example:
Mike runs its < < vehicule_placeholder > > in the city. But its < < VEHICULE_PLACEHOLDER > > is meant to be shared.
If the value of this placeholder in the file merger is 'bike', the sentence should be:
Mike runs his bike in the city. But his BIKE is meant to be shared.
Is this possible? How?
Thank you.
You can do it. A character style for this configuration placeholder text, set in all caps.
-
Variable setting wrong with dynamic action for the region of report
Hello
I can't setting a variable. Here are the details of connection:
Connection information:
TCARMY workspace
User Apex_dev
Password dev_apex
Application 88542
Page 11
If you run the page 11 and just click on submit, there will be two rows. If you click on one, the modal region won't say no data found. If you click on the button submit once again, the value is passed if you click on it now, the results arrive. If you click on the second row, it still shows the value of the first row. If you click on submit again after clicking on the second line, then it is displayed correctly. It seems that the value is set to submit it. I want this to work when clicked, and then for the sql to run with the value that is in this variable when clicks on the element. There is a bit of javascript page level and dynamic action. Something is not right to the installation.
The modal window should popup and run the sql at that time with the variable data and view the two columns. And if the user clicks on the second row, it would display the data in the row.
Thank youTim
TC-army wrote:
If you run the page 11 and just click on submit, there will be two rows. If you click on one, the modal region won't say no data found. If you click on the button submit once again, the value is passed if you click on it now, the results arrive. If you click on the second row, it still shows the value of the first row. If you click on submit again after clicking on the second line, then it is displayed correctly. It seems that the value is set to submit it. I want this to work when clicked, and then for the sql to run with the value that is in this variable when clicks on the element. There is a bit of javascript page level and dynamic action. Something is not right to the installation.
What has not been set up right, it's that the element of P11_NAICNUMD parameter was not specified in the source attribute of Page to go to the region, modal Discount. The current value in the browser page, therefore, was not defined in session state when the report has been updated by the dynamic action. When
-
How to set a Total sum only for the newly added lines
Hi Experts,
JDeveloper 12.1.3.0.0
Hi I have a table and above, I have an Add button. During the click on Add I only show new lines using CreateWithParams.
Existing or rescued lines that I went under certain conditions as false. So, how can I calculate the sum of the salary only for new lines and display it in the column Footer.
Thank you
Roy
One approach would be to browse all lines and sum of lines in the getter for the variable 'total '.
http://adfcodebits.blogspot.com/2010/04/bit-4-iterating-view-object-using.html
Dario
-
I would like to know what version of ESXi, vSphere would support the fault tolerance
I would like to know what version of ESXi, vSphere support (Standard, Enterprise or Enterprise Plus) fault tolerance.
It is available in Advanced, Enterprise and Enterprise Plus - http://www.vmware.com/products/vsphere/mid-size-and-enterprise-business/buy.html.
Dave
VMware communities user moderator
Now available - vSphere Quick Start Guide
You have a system or a PCI with VMDirectPath? Submit your specifications to Officieux VMDirectPath HCL.
-
Hello
I am facing a problem with "LSI Logic / Symbios Logic MegaRAID SAS-3 3008 [fury] (rev 02)" controller when "intel_iommu = we ' setting is enabled in grub." I'm working on SRIOV and I need to activate intel_iommu = we're in grub, so that it allows the transmission of memory and management mechanism. But when I activate intel_iommu = on and after restart my system stops with error ("" megaraid: could not get the pp list "") pls find the attchement for details of the error. I googled just this error but did not patch appropriate to exploit. If the similar question has already been resolved Dell, please send me the fix and the appropriate measures to move forward.My System Configuration:
DELLR730 13 G Server Xeon of Intel (r) CPU E5-2620 v3 @ 2.40 GHz with 32 GB of RAM
OS: SLES12 and I also tried on RHEL7.1SRIOV and Intel VT - d is enabled in the BIOS
Note: If intel_iommu = parameter is removed from the grub, then everything works as expected.
--> SLES12 error
--> Error RHEL
-------------------------------------************************************------------------------------------------------------
--> information about the command lspci:
03:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS-3 3008 [fury] (rev 02)
Subsystem: Dell PERC H330 Mini
Control: I/o + Mem + BusMaster + SpecCycle - MemWINV - VGASnoop - ParErr - Stepping - SERR - FastB2B - DisINTx +.
Status: Cap + 66 MHz-UDF-FastB2B-ParErr-DEVSEL = fast > TAbort -SERR.
Latency: 0
Interruption: pin has routed to IRQ 26
Region 0: I/o ports to 2000 [size = 256]
Region 1: Memory at 94500000 (64-bit, non-prefetchable) [size = 64K]
Region 3: Memory at 94400000 (64-bit, non-prefetchable) [size = 1 M]
Expansion ROM 93600000 [disabled] [size = 1 M]
Features: [50] power management version 3
Flags: PMEClk - DSI - D1 + D2 + AuxCurrent = 0mA SME (D0 - D1 - D2-, D3hot-, D3cold-)
Status: D0 NoSoftRst + SMB-Enable-DSel is DScale 0 = 0 SME -.
Capabilities: [68] express endpoint (v2), MSI point 00
DevCap: MaxPayload 4096 bytes, PhantFunc 0, L0s latency<64ns, l1="">64ns,><>
ExtTag + AttnBtn - AttnInd - PwrInd - BMS + FLReset +.
DevCtl: Report errors: correctable-no - Fatal+ Fatal+ Unsupported +
RlxdOrd + ExtTag + PhantFunc - AuxPwr - FLReset - + NoSnoop
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr + UncorrErr - FatalErr - UnsuppReq + AuxPwr - TransPend-
LnkCap: Port #0, 8GT/s speed, width x 8, L0s ASPM, output latency L0s<2us, l1="">2us,><>
ClockPM - Surprise - LLActRep - BwNot-
LnkCtl: ASPM with disabilities; RCB 64 invalid bytes - CommClk +.
ExtSynch - ClockPM - AutWidDis - BWInt - AutBWInt-
LnkSta: Speed 8GT/s, width x 8, TrErr - Train - SlotClk + DLActive - BWMgmt - ABWMgmt -.
DevCap2: Completion Timeout: BC, TimeoutDis +, LTR-, OBFF unsupported range
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-, -LTR, OBFF disabled
LnkCtl2: Target the link speed: 8GT/s, EnterCompliance - SpeedDis -.
Margin of transmission: operation Normal Range, EnterModifiedCompliance - ComplianceSOS -.
De-emphasis compliance:-6dB
LnkSta2: Current level of de-emphasis: 6dB, EqualizationComplete +, EqualizationPhase1 +.
EqualizationPhase2 +, EqualizationPhase3 +, and LinkEqualizationRequest +.
Capabilities: [d0] vital product data
Resources small unknown type 00, will decode any more.
Capabilities: [a8] MSI: Enable - Count = 1/1 Maskable + 64 bit +.
Address: 0000000000000000 Data: 0000
Masking: 00000000 pending: 00000000
Capabilities: [c0] MSI - x: activate + Count = 97 masked -.
Vector table: BAR = 1 offset = 0000e000
PBA: BAR = 1 offset = 0000f000
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP - SDÉS - TLP - FCP - CmpltTO - CmpltAbrt - UnxCmplt - RxOF - MalfTLP - CCRS - UnsupReq - ACSViol-
UEMsk: DLP - SDÉS - TLP - FCP - CmpltTO - CmpltAbrt-UnxCmplt-RxOF - MalfTLP - CCRS - UnsupReq - ACSViol-
UESvrt: DLP SDÉS + TLP + FCP + CmpltTO + RxOF + MalfTLP + ECRC + UnsupReq - ACSViol - - UnxCmplt - CmpltAbrt
CESta: RxErr - BadTLP - BadDLLP - bearing - Timeout - NonFatalErr +.
CEMsk: RxErr + BadTLP + BadDLLP + rotation + delay + NonFatalErr +.
AerCap acquired: first error pointer: 00, GenCap + CGenEn + ChkCap + ChkEn +.
Capabilities: [1e0 v1] #19
Capabilities: [1 c 0 v1] power budgeting??>
Capabilities: [190 v1] #16
Capabilities: [148 v1] Alternative Routing-ID interpretation (ARI)
ARICap: MFVC - ACS-, then run: 0
ARICtl: MFVC - ACS-, function group: 0
Kernel in use driver: megaraid_sas
--------------------------------------------------**************************************----------------------------------------------See you soon,.
Praveen
Hello Praveen
The H330 doesn't have a memory I/O management. activate the function that does not exist, it is probably why the question is being implemented.
Thank you
-
Hello everyone,
my company is using PDF documents with hyperlinks to Lotus Notes databases.
When I open one of these files with Adobe Reader Default Setup, I can not open the hyperlinks.
When I disable the safe_mode at startup, it is possible to open links.
To ensure safety, we try to set the trust for our Notes Server site, but I couldn't find a solution.
Our servers work with Lotus Notes 9, customers use the Version 8.5.3.
Clients are installed with Windows 7 Enterprise.
We test with Adobe Reader DC, Version 2015.007.20033
Thanks for your support in this matter.
Thank you in advance everybody!
Hi oliverh33447604,
Open Acrobat Reader DC, navigate to the Edit-> Preferences-> Trust Manager menu-> settings
Use the option of the customer to add to the list of Web sites.
Kind regards
Nicos
-
Setting Internet Explorer 7.0 for the planning
Hi Hyperion Experts,
I read several times in this forum that planning facing problem with the version of Internet Explore 7.0 and use better earlier. opposites of some settings in IE 7.0.
Could someone help me how to put IE 7.0 for planning, that I'm unable to degrade my IE.
Thanks in advance for any help!
Concerning
N KumarHello
VMWare must fine being run on your laptop, as long as you don't try and run too much, or vmware server or vmware workstation should be fine, I think that the server is free and must have enough features.
See you soon
John
http://John-Goodwin.blogspot.com/ -
Can someone clarify the following:
vShpere 4.0, ESXi 4.0.
When a customer what OS has been configured to FT running at the stage of lock on two hosts, what happens if that guest OS system suffers from a panic of the server or the application freezes or crashes. The guest on the secondary host computer also displays the same conditions? Thanks,-Jeff
Yes - FT does not protect against the OS or applications failures, only underlying hardware failures.
-Matt
VCP, vExpert, Unix Geek
Maybe you are looking for
-
Why FireFox 11 can't see newly installed Java 1.6.0_31 on Mac?
I used the software update on my OSX Lion Mac upgrade to Java 1.6.0_31 - b04-413. The update showed as much success and this is the version specified in the Java preferences utility. I then rebooted and you've restarted Firefox several times, but Fir
-
Satellite Pro A100-302: what is maximum size of HARD drive?
Hello Someone who knows the maximum capacity on the hard drive of this laptop? Original is 100 GB, is it possible to upgrade to 320 GB? Elegant
-
Smart start checking hard drive fail
Laptop start-up started showing check smart fail, and I need a new hard drive, where I can buy it. I checked the HP store, but found nothing. model G56-100SA Product LD701EA #ABU Series CNF0512STD Is it possible to buy a different drive for this lapt
-
Problem: A problem on your computer is preventing updates to be downloaded or installed
I spent the last day trying to solve this problem. I started with critical updates that should be applied. I tried to run windows update in order to install, but it still fails. When I'm going to update the story it shows no failure so I can not g
-
Locate the sound card or where is this device driver?
Hello I have no sound with Widows VISTA. Nothing has changed and there is no virus on this machine. It has just stopped working. My speakers are OK checked with "fix problem with Windows. I would like to see if the sound card broke or what other d