Setting up SSH on a 3845 router?

Similar Questions

• Unable to SSH for outside the router No. 2851

  Hello

  I want to SSH to the external interface of our router No. 2851.

  SSH works fine on the internal interfaces.

  I have install the ACL is access (1 applied to the vty line and one to the external interface).

  The configuration looks like the following:

  line vty 0 4

  access-class 102 in

  30 logout-WARNING

  length 0

  entry ssh transport

  access list 102 permit tcp any gt 1024 any eq 22

  Outside_ACL extended IP access list

  permitted tcp and gt 1024 no matter what eq 22 log

  Is there anything else that I should consider when setting up SSH on the external interface?

  TIA,

  Michael

  Michael

  I notice that there is a card encryption on the interface (I have would have supposed of your previous comment that you access the router via VPN) and I wonder if it is possible that SSH entering your remote address is considered to be entering the card encryption VPN traffic. Could you try the external address of some other address source SSH and see if that changes things?

  Or can you provide details on what is in the card encryption - and perhaps think about putting something in the map encryption that would exclude SSH to the external interface.

  HTH

  Rick

• The 3845 router question redundant power supply

  Is it possible to swap a bad redundant power on a without voltage 3845 router the router?

  The FAQ at this URL indicates that they ARE actually hot.  Please look at here, under 'System (AC/DC) Power'.

• How can I set up the AEBS as a router with sky Hub as a modem?

  I have sky broadband with a Hub of Sky SR102-Z router. I had the problems of slow speed, and the tour engineer told me that it is caused by the interference of a wi - fi connection. I have an Airport Extreme Base Station that I stopped using when I got sky, but I now use it as a router (the Hub of sky is quite limited) connected to the Sky as the Modem concentrator. I would be grateful for any advice on how to set up the AEBS so that it fills the air Hub. Thank you.

  I would be grateful for any advice on how to set up the AEBS so that it fills the sky Hub

  If you want to use as a router AirPort Extreme... it would mean that hub Heaven must be reconfigured to act as a modem mode simple bridge.

  Whether or not it's possible and even if it is possible... Whether or not the sky will support this type of installation are questions for heaven. So, you will need get clarification from heaven on this topic before you can proceed with the configuration of the AirPort Extreme.

  You can keep in mind that the hubs of some suppliers cannot be reconfigured to make the function of the device as a modem mode simple bridge. If which is the case with the sky... then you will need to set up the AirPort Extreme in Bridge Mode and continue to let the Sky router as the network router, same function if the wireless may not be enabled on the hub of the sky.

• setting the time & date on the router or Web site atomic time (to synchronize times)

  Is there a program that will perform the same function as this file control breaks:
  NET TIME \\[local pc name or an ip] / set yes

  But instead of the parameter to another pc on your network will put it to your router (Cisco Linksys WRT110 in my case) or an atomic clock Web site?

  I know VB, I can write my a program to do? If so, what would be the code to remove this date & time of my router or a Web site?

  Time Windows synchronizes on a time server NTP [S].

  The sequence of commands that I used in the past (as admin) is:
  NET time /setsntp:192.168.1.1
  w32tm/config /update
  w32tm/Resync /rediscover

  Where "192.168.1.1" is replaced by the time server NTP which synchronize you to.
  Not sure if the Linksys routers include a SNTP server.

  Microsoft replacement instructions are here:

  "How to configure a time server authoritative in Windows XP"
    <>http://support.Microsoft.com/kb/314054 >
  Jump to halfway down to the paragraph "the time service Configuration Windows to use an external time source.

  HTH,
  JW

• I'm unable to set up my new Linksys E1000 router to my computer dell Inspiron B130 laptop.

  When you try to configure my linksys E1000 new router I get... We can not define your... router wireless connection requires Wi - Fi connection are managed by microsoft windows.  some computers have a different wireless connections Manager... I tried to disable my dell 1470 wireless unsuccessfully lan card to get the new router loaded... any suggestions?

  Hi Devar,

  When you configure a new Wifi router immediately, you can connect to the radio

  you have to go on the wireless router and you also need an ethernet cable to connect the router to your pc wirelessly

  normally all routers come with an installation cd. But if it does not

  Open your web browser and type the ip address of the default gateway

  The IP address of the Linksys routers is 192.168.1.1

  from there, you can set the security features and everything and after that you have set up passwords and everything please connect your modem to the wireless router so that you can access the internet

  to manage your network wirelessly with the windows wireless client, please activate your Automatic Configuration WZC wireless

  follow these steps to activate the automatic Wireless Configuration

  Start menu - click on RUN

  type in SERVICES. Scroll down the list until you see SMC Wireless Auto Configuration

  Double-click and should be in service type: automatic

  and also, click Start to start the service.

  Hope that helps

• When you set the IP address of the router, WRT160N Inaccessible

  Hello

  I bought a WRT160N router yesterday and eagerly tried to connect my laptop to the internet (ADSL) modem using this router. As my ADSL modem is a router DHCP too, and I want to keep it like that, I have it plugged in ethernet cable form one of my ADSL modem/router, LAN ports in one of the LAN ports on the modem, Linksys have the Linksys operating as a bridge. However when I tried to specify an address of router static IP (192.168.1.254) in the basic parameters of configuration Linksys Panel, disabled the DHCP setting and saved, I could not connect to the router more using this new IP address - my browser tells me that the Web page doesn't seem to exist, but it cannot establish a connection with her. Then I have to reset the router in order to access configuration panels using the default address 192.168.1.1. Is there a reason why I cannot access the control panels of the router with the new IP address of the router that I've specified?

  Thanks for any help,

  Hello

  the problem is resolved, be it in a different way. I tried your trick to wait 30 seconds after the registration and the recycling of the modem, but this had no effect. What helped does not change the settings for address IP Routerl and the setting from the DHCP server on the router for the disabled at the same time. If I only changed the setting to the IP address of the router and recorded, the modem has been reset automatically and starts with the new correct router address. After that I changed the setting of DHCP server to the WRTN160 to off and then I was able to get the router working, like I wanted.

  I assume that when you connect the router to a computer reset (after taking out the IP address of the computer) with DHCP from the active router, the router assigns an IP address to the computer that somehow interferes with the local IP address parameter, if you define that at the same time.

  In any case, all work now, and I have excellent signal everywhere in the House. I guess that congratulations go to me :-) but still thanks to eliminate one possible cause of the problem

  Kind regards

  Gerard

• Set up a wireless network without router

  When you configure a wireless network without router, how many computers can I connet to this network?  Is there a limit?

  Wow, I'm sorry.  I must have had a brain freeze when I read your post.  * From http://www.tomshardware.com/forum/20446-43-wireless-networking-general

  What is the maximum number of wireless clients that can be networked using the Ad-Hoc mode, i.e. without an access point?

  The theoretical limit, which is the same as in Ethernet, is determined by the 48-bit MAC address field in each frame of wireless data. The practical limit is determined by the constraints that can be integrated to client drivers. As a general rule, Ad-Hoc networks with 16 to 32 stations should be possible.

  See you soon

• Need help the NM-CIDS upgrade on Cisco 3845 router.

  Can someone tell me all the files I need to improve my 5,0000 E3 to E4 6,0000 ID?  I think I should be able to do with the material that I currently have.  I do not have the resources to upgrade the router or the module NM-CIDS.  I want to update the E4 because it seems that Cisco is no longer put signatures for E3.  Documentation, I read that I should at least the Image of the system, the Service Pack, the recovery Image and update engine files.  I see several different times with a GOAL in the file names naming convention.  I'm not sure what I will need the names of specific files.

  A screenshot of version see is lower.

  See the version
  Application partition:

  Cisco Intrusion Prevention System, Version 5,0000 E3

  Host:
  Domain keys key1.0
  Definition of signature:
  Update of the signing S479.0 2010-03-19
  Virus update V1.4 2007-03-02
  OS version: 2.4.30 - IDS-smp-bigphys
  Platform: NM-CIDS
  Serial number: FOC11014468
  License expires: August 14, 2010 UTC
  Sensor time is 17 days.
  Using 509292544 bytes of available memory (79% of use) 403263488
  system uses 17.7 M off 29,0 M bytes of disk space available (61% of use)
  the application data uses 34.1 M off 174.7 M bytes of disk space available (21% of use)
  start using 39.1 M off 75.9 M bytes of disk space available (54% of use)
  Application log using 532,3 M off bytes of 2.8 G of disk space available (20% of use)

  MainApp N-2008_JUN_06_02_35 (release) 2008-06 - 06T 03: 23:18 - 0500 Running
  AnalysisEngine NO-2008_OCT_16_22_05 (release) 2008-10-16 T 22: 30:37 - 0500 Running
  CLI-N-2008_JUN_06_02_35 (release) 2008-06 - 06T 03: 23:18 - 0500

  Upgrade history:

  * IPS - GIS - S478 - req - E3 18:12:38 UTC Monday, March 22, 2010
  IPS-GIS-S479-req - E3.pkg 14:00:57 UTC Friday, March 26, 2010

  Version 1.1 - 5, 0000 E3 recovery partition

  You only need the IPS - K9 - 6.0 - 6 - E4.pkg file.

  Put it on an FTP server and jump on the sensor CLI and run this command:

  upgrade ftp: / / (user name) @(ipaddress of your ftp server)//(directory, if any)/IPS-K9-6.0-6-E4.pkg)

  -Bob

• Setting UP SSH without PASSWORD fails during the installation of the grid

  Hello

  The operating system and the virtual machine configuration:

  There are 2 physical Oracle servers base (model # 2 - Oracle SPARC Solaris 11.1, T4). On both machine 'Oracle VM for SPARC' software is installed and logical domains are configured with Solaris 11.1. Oracle RAC 2 node cluster is currently Setup between the logical field in each of the servers.

  Objective:

  We plan to install and configure Oracle RAC 11 g R2 (11.2.0.4) on two machines of Oracle VM. Control script of pre-installation (runcluvfy.sh) on the RAC node is completed without errors/warning.

  Question:

  During the installation of oracle grid infrastructure, SSH configuration failed and on the shell prompt shows JVM CRASH LIB...

  I'm not able to install RAC because of this problem.

  Your suggestions/help will be greatly appreciated.

  Thank you.

  Support of Oracle suggested to commented LD_LIBRARY_PATH to the grid user profile

  So I think that you should continue to discuss with Oracle Support.

  They are more that we know.

  Concerning

  Mr. Mahir Quluzade

• How to set the SSH Timeout ESX 3.5 host using Putty

  How can I configure the ssh Timeout on a 3.5 ESX host for that after I PuTTY in the host he drops the ssh connection after 15 minutes if the session is inactive?

  Pete

  Not sure it's possible with sshd.

  But you can do with bash.

  Place just an environment variable (in rc.local or profile):

  Export TMOUT = 900

  André

  * If you found this device or any other answer useful please consider awarding points for correct or helpful answers

• HP Laser Jet 8600 Plus: re - set the printer for new wireless router. I use a Mac.

  I just installed new internet.  How can I reset my HP Laser Jet more than 8600 to print?  I use a MAC not a PC!

  You can use the Control Panel before the printer via the network settings menu.

• Problems setting up router WRT1900ac and fiber

  I feel that my question is so obscure that I won't be able to get a lot of help here, but I'll post anyway.

  First of all, I live in the Philippines. My ISP is PLDT. I have FTTH - fiber to the home. My internet connection is DHCP - no login or password. I thought that perhaps they checked the serial number on the modem to see if I was an authorized user but apparently not; They told me if I wanted to buy another optical modem, I could and that I wouldn't need to do anything to save it on the network, but that they could not provide me with a list of modems that would work.

  They delivered to me with a router/modem made by a company called FiberHome. "Like the big business of high-tech directly affiliated to belonging to the active state of oversight and Board of Directors of the Council of State, FiberHome Technologies is the company of the kernel located in Wuhan Optics Valley of China."

  The model number is AN5506-04-FG. There are very few configurable on this. Can I change my wifi network name (they insist that the name of the network begins with PLDTHOMEFIBR, no idea why) and a few passwords here and there. For the most part, I just post status on the LAN and WAN.

  Therefore, because it is so little that I can do with it that I decided that I needed a router/gateway and not simply an Extender. I bought the WRT1900ac.

  Brought it home, that he repaired, it connected via ethernet cable between a LAN port on the FiberHome on the Internet on the Linksys port.  I then used the WiFi on my iPad to try on the Linksys Setup, try with Safari and Chrome.

  Went to put in place and smart control of Linksys could not understand my internet connection, despite several reboots, power off and cable disconnected, etc.

  So I went to the manual configuration. I put the connection to a static IP address. Following the minimal instructions in the booklet of FiberHome, I put the IP address of the router to 192.168.1.28; the subnet mask of 255.255.255.0; This gateway 192.168.1.1 (internal IP of the fiber to the home, address) DNS of Google DNS.

  This would actually work - but only for a few minutes at a time. Then the network diagram would show that I was always connected to the FiberHome but no connection to Internet in addition. (Although my PC, connected to the FiberHome via a LAN cable, still had access to the internet.)

  I used the live chat Linksys to ask an agent to this topic. She said that my gateway setting is correct. She had me reset the router and try again, but he could not yet know the connection to the internet on its own. She had me download the iOS app and try there, but same result. So I received a ticket number and ended the chat session.

  Now, I tried to set the internet connection on the router at the bridge. But once I did, I was unable to connect to the router via WiFi. I needed to do a reset to be able to access it again.

  At this point I called my ISP. They told me that if I wanted to add another router like that, they would need to reset my router/modem FiberHome bridged mode. But they are unable to do it remotely and cannot (or don't want to) give me instructions on how to do it myself.  They need to send a technician to my home. They could not tell me when. I have to wait for a call. (I got a ticket number).

  This means that for now, I have a blue and black, sitting bins there, I can't do anything with.

  So I'm waiting, I thought I'd post this in the hope that someone might have some ideas configuration I could try or for the general amusement of peoples.

  Thank you!

  You may have a conflict between the two routers in IP subnet. In this case the WRT1900AC will change it's default subnet to 10.x.x.x instead of 192.168.1.1

  You can find the new IP address of the router by looking at a customers connect ITI information IP address appears as the default gateway.

• Do I need a router to provide internet to my tablet, if this isn't how I've set up.

  Do I need a router to provide internet to my tablet, if this isn't how I've set up.

  Do I need a router to provide internet to my tablet, if this isn't how I've set up.

  A wireless router broadband is preferable, as indicated by the others.

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-home-network

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-wireless-network

  If you have a Windows 7 machine equipped with a wireless (WiFi) (Home Premium/Professional/Enterprise/ultimate), you can use the integrated hosted network feature to turn the Windows 7 machine into a wireless router. Look at Connectify or Virtual Router (both free) of the to do.

  http://www.Connectify.me/

  http://virtualrouter.codeplex.com/

• is it possible to connect with SSH from router to router?

  is it possible to connect with SSH (1.0 or 2.0) to a CISCO-router/Switch to another CISCO-router/Switch?

  I think that an SSH connection to a router/switch is no longer possible to a women (Windows/Linux/Unix)

  is it not?

  I don't know if Cisco Compatible SSH 2.0, but there IOS - s that support ssh 1.0 and you can connect with ssh 1.0 from a cisco device (if it supports) to any device with

  Router # ssh?

  Select encryption algorithm - c

  -l Log in using that username

  options to specify o

  p connect to this port

  Address WORD IP or hostname of a remote system

  Router # ssh x.x.x.x