I'm unable to set up my new Linksys E1000 router to my computer dell Inspiron B130 laptop.

Similar Questions

• Shaw and my new Linksys WRT310N router

  Basically, I tried a router Dlink $ 50 and failed. I tried a $ 100 Linksys router and failed. My ISP is Shaw and no 3rd party router seems to work with it. I have connected my Shaw Surfboard Cable Modem to the Internet port on my router and router connection Port 1 to the Ethernet port on my desktop. I talked to support several times without success. Can someone help me understand this problem?

  "Just to get the mac address of the PC which is on your ISP shaw.

  AFAIK, you don't need to do. I'm on Shaw, using a WRT-320N and have no problem at all (at least not THIS problem).

  There are three different pieces of this puzzle and you have not provided enough information to determine what part is actually the problem:

  -connection makes Shaw so you are also connected to the internet

  -you are connected to the internet but cannot browse, receive emails etc. of your main (or other) machine which is connected BY WIRE to the router

  -you are connected but cannot browse wireless

  If the problem is that the first (and I think that's what you wrote), try the following - it is conceivable that one or more of your IP addresses are contradictory. In order to cross Shaw it is easier if you just "start over." Cut your cable Modem. Turn off your router. Re-turn on your modem and wait until it shows who is connected with the signal. Then turn on your router. This should dispel any questions.

  Most of the machines are set to "dhcp", which will allow the machine to automatically retrieve an address.

  If no joy, please advise what your PC (Windoze? Mac?) and what version of operating system you are using (Windoze Vista? Windows 7? Win XP? OSX? etc.)

• New HDD in my Dell INSPIRON N5010 laptop, will I go to 5400 RPM or 7200 RPM HARD drive

  I bought the DELL N5010 laptop about 4 years back, and currently it is more under warranty.
  2 days back my hard drive crashed and could not start or install the OS as there are bad sectors on the hard drive has. I plan to buy a new hard drive.

  Which one should I go for a 5400 RPM or 7200 RPM. I would go to 7200 RPM, as it is faster, but I read on the internet that the 7200 RPM generates more heat then 5400 RPM and my laptop is already facing heating problem. I had replaced the fan about 2 months as my laptop used to close because of the heat. The problem of heating has not changed, but laptop does not stop :)

  Anyone using the DELL N5010 laptop with a 7200 RPM HARD drive and he's fine?

  Any kind of recommendation will be greatly appreciated.

  Kind regards

  Sach

  Thanks for the recommendation. The sales in the shop man also recommended the same thing. I bought Seagate 5200 SSHD(Solid State Hybrid Drives) which is still better than the conventional hard drive. :)

  Kind regards
  Sachin

• reinstalled xp pro on a dell inspiron 1100 laptop, are unable to open a session, says no modem found copde 62 and 63. .Mike

  I reinstalled xp on dell inspiron 1100, could not get to connect wireless or ethernet.  It said no modem error #62 and 63 error no modem not found, I had xp pro edition before but now have xp base, you can help me find the modem can also get DVDs to play, without a decoder.   Thank you, mike

  Hello

  Follow these steps and check if the problem persists.

  I suggest you to reinstall modem drivers:

  (a) go to the manufacturer website and download the drivers. This will
  usually come as a zip file or installation program.

  (b) if its an installation program, run it. No need to go further.

  (c) if it is a zip file, unzip all the files in a temporary directory.

  (d) right click on my computer, then select Properties > | material | > Device of
  Manager.

  (e) to locate the modem on your equipment list. It could be among the "pci
  device communication "or similar.

  (f) right click the icon and select get updated driver.

  (g) install from a specific location and follow the instructions of the wizard through. Specify
  where you unzipped the files. Some create additional records
  decompression so you will look for an INF.

  (h) proceed to configure the modem in the properties applet, phone and modem in the
  Control Panel and verify that your settings are correct.

  See also:

  How to manage devices in Windows XP

• I forgot my password for windows 7 for my laptop and a reset disk has not been created. How can I recover the password or create a new one? and I have a dell desktop inspiron one 19

  I forgot my password for windows 7 for my laptop and a reset disk has not been created. How can I recover the password or create a new one? and I have a dell inspiron one 19 desktop... your help will be very appreciated thanks in advance!

  Here are the usual methods to solve this problem:

  • Restart the computer with your Windows repair CD, then use system restore to set Windows in a few days (only works if you have recently changed the password).
  • Logging in as a different admin account and then reset the password for your existing account (works only if create you an alternative admin account).
  • Log in as administrator mode without failure, then reset the password for your existing account (works only if you have activated the account administrator and know its password).
  • Insert your flash drive USB with the password key file (only works if you have created such a keyfile).
  • Check your paper files (works only if you threw down the password somewhere)

  If none of these standard precautions work for you, then the remedy will be painful. Post again if this is the case.

• Dell inspiron E1505 with Windows Vista system restore to factory setting led by mistake. The operating system version is incompatible with Startup Repair tool

  I tried to restore my Dell Inspiron E1505 laptop to the factory setting.  I pressed F8 then selected repair and then Dell Factory Image Restore.  Used to format hard drive.  He formatted the hard drive and then he restored the system.  Suddenly, a small window pops up without any details, but saying "error".  I restarted the laptop, it entered into Startup Repair mode.  But even once showed error "operating system version is incompatible with startup repair".  I don't have my windows CD/DVD.  Although the windows sticker is still on the laptop.  Please advise me how to install the system on the laptop so I can use the same.  Please note that I am in Gurgaon (India).

  Thank you

  Hello

  Because the computer is located in a no start situation and you don't have the installation disc, it is best to contact the manufacturer for assistance.

• Unable to connect to Linksys WRT120N router using Notebook Pavilion dv1000

  Hello

  I recently bought a Linksys WRT120N router for my existing HP Pavilion dv1000 laptop. I am not able to connect to this router to my laptop.

  The steps I am following are-

  1. I activated the WLAN by clicking on the switch.

  2 a permit wireless

  3. given the available wireless networks

  4 selected my network (which is a secure (WPA) wireless network) and clicked on connect

  5 enter the network key (twice) and clicked on connect

  I get the message - "Please wait so that windows connects to the network, waiting for the network"... After a while the screen goes away; There is no message of success or failure of a current connection. The same wireless connection works my other laptop Toshiba in a jiffy, which means that my router seems to have been implemented correctly. Both are on the version of Windows XP Home Edition, SP3, 2002.

  I did the following settings for my wireless connection: -.

  the network card is PRO/Wireless 2200BG network connection

  I have the most up to date driver, checked for an update

  the network for my wireless connection authentication type is WPA - PSK

  data encryption is TKIP

  is the wireless network - enabled network (WPA) wireless security

  What follows is set for the wireless to 192.168.0.1

  manual configuration

  network-mixed mode

  name of the channel-xyz

  channel width - 20 mhz only

  great channel-auto

  STD - 6 channel - 2.437 GHZ

  SSID broadcast-enabled

  wireless security-mode-WPA Personal

  Please please help me... Please let me know if you need more information about the same... TNX!

  guys, I found others who have faced the same problem too

  the solution to this problem is the Forum of linksys... the key was to update the firmware for the router and get the wifi driver was last updated to intel!

  Here is the link for the same

  http://forums.linksysbycisco.com/Linksys/board/message?board.ID=Wireless_Routers&thread.ID=146826&view=by_date_ascending&page=4

• Unable to connect to the wireless network WPA2 in Windows 7 with Dell E6400

  Hello

  I've spent almost a week to find the following problem with one of my laptops:
  Laptop Dell Latitude E6400
  CPU Intel Core 2 Duo T9400 2.53 GHz
  Memory 4 GB
  OS Windows 7 SP1 32 bit Home Premium
  Card WiFi Dell Wireless 1397 WLAN Mini Card
  Intel 82567LM Gigabit Network Connection Ethernet card

  With the wireless configuration (Ethernet is unplugged), my E6400 sees the Motorola SBG 6580 wifi router using WPA2, but when I try to connect to this router (with WPA2 password) I got the error message:
  Windows could not connect to myrouter.

  I've updated all the drivers with the latest version and I still have the same error message.

  I have another laptop Dell E4300 under Windows 7 SP1 32 bit Home Premium and I can connect to the Motorola router without problems.

  Do you have ideas of how to solve this problem?

  Thank you

  I had this problem with my new Dell 1545 & wireless 1397 card, but it was some time ago. The utility Dell WiFi was, it turned out, interfere with the management of the windows of the WiFi card. There was also a problem of compatibility with versions of driver and I had to keep the driver to the version Windows offered two years ago. You can read about it at low signal wireless Dell Inspiron 1564 laptop 1397 WLAN Mini card , but do not forget that it was some time ago, it's with another model of Dell & that no router was involved.

  You can also try asking Dell support, but I never had any help from them at all, despite the request.

• Server Windows 2008 R2 Standard - TrustedInstaller owner of C:\ Drive - unable to set new owner

  I have a new Windows 2008 R2 Standard Server.  The original question started with W32Time won't start do not, but I think that it comes to this issue.  When I look at the 'owner' of the C:\ drive it shows "TrustedInstaller" as long as the current owner.  When I try to replace the owner of the server administrator account, I get this error:

  Unable to set new owner the disk Local (c).  Access is denied.

  Any ideas?

  Hello, Chris Prerno,.

  Microsoft Answers is for consumer issues on Windows XP, Windows Vista, Windows 7 and Windows 8 Preview Release. As you question deals with Windows Server 2008, there is a specific forum for this OS on TechNet.

  Please click on the link below and repost your question.
  http://social.technet.Microsoft.com/forums/en-us/winserverGP/threads

  Thank you

• I deleted my Firefox sync account. How can I set up a new account on the same device?

  Now, when I open Firefox and go to tools, there is only the option "Synchronize now" rather than the "Set Up Sync" option. My account is permanently deleted, b/c "Unable to locate your account" Sync response (s) if I try to sync. How to set up a new account on this same device synchronization? Thank you.

  Hi cloudinoakland, go to Preferences > tools > synchronize and untie your device. You should then get the opportunity to implement synchronization and create a new account again.

• Unable to set vROPS on AV 3.0

  Unable to set vrops on av 3.0-

  • new installation
  • connected to the console and ran /etc/wemi/utils/disable_ssl_validation.sh
  • restarted
  • AD bind configuration step, the roles and permissions
  • input domain name COMPLETE for device vrops, AD, user name with permissions admin and password

  This error occurs: internal server error. Server has encountered an internal error and could not respond to your request. Please try again later. If this problem persists, contact your service provider.

  Nothing relevant is reported in the newspapers. Anyone experience this problem?

  Apparently he doesn't like not my FULL domain name while it is able to ping in the console of AVM with domain FULL of the vrops device. Jobs using https://VROPS_IP_ADDRESS or https://VROPS_HOSTNAME

• Unable to set up the transaction manager

  I'm unable to set up the transaction manager. I am using weblogic.
  
  I created component TransactionManager and placed it to atg/dynamo/service/transaction. This is what I did.
  #/ atg/dynamo/service/transaction/TransactionManager
  $class = atg.nucleus.StaticMethodReference
  staticMethodName = weblogic.transaction.TxHelper.getTransactionManager
  
  I am getting error on next console:
  atg.dtm.TransactionDemarcationException: the transactionManager has not been specified in the call to begin(). Delimitation of the transaction fails.
  
  getTransactionManager() is null begin the method of TransactionDemarcation:
  
  TD. Begin (getTransactionManager (), 3);
  
  I tried with mysql and oracle, that the two databases.
  
  Any help?
  
  Thanks in advance,

  I have it. It was a stupid mistake. Instead of getting the component via the name of will that I tried to get OOTB component by using the new operator, so in order to subject current OOTB, Manager of transactions was been set to null values.

  Sorry Shaik, my bad!

  Appreciate the answers!

• I am trying to set up my new iPhone 7 more but it says SIM necessary?

  Im trying to set up my new iPhone Plus 7 but it says "SIM" required?

  You must use a sim card to activate the iPhone.

  Don't you have a?

  Where did you buy this iPhone?

  Has not chosen a carrier when you purchase it?

  Don't you have a cellular carrier that you want to use iPhone with?

• should I "set up as new iphone."

  Hello

  I didn't save my 6s IPhone since I got it and I don't know whether to "set up as new iPhone" or "restore from this backup" (my old iPhone 5).

  I'm afraid that if I "set up as new Iphone" I will lose all my photos my camera etc. For more than 30 weeks I had this 6 s IPhone and I have over 3000 photos.

  Please let me know which option to choose. -I don't mind if photos from my old phone to the folder/location same as pictures of my new phone as long as I do not lose them!

  Thank you

  Holly

  Hello

  When you load an iphone it should automatically be saved on iCloud

  Go to the last backup of settings-iCloud check if it's not very old use that one

  When you set iPhone it will ask you if you want to use backup say yes, if its a recent.

  See you soon

  Brian

• Apple Store will set up my new iPhone?

  WWill Apple Store set up my new iPhone 7 and I have to make an appointment?

  If you are picking up the iPhone in the store, then Yes, they will set it for you without any appointment.

  If you bring it the store having bought somewhere else, then Yes, make an appointment and he will set it for you.