SG200 SG200 VLAN Trunk does not

Similar Questions

• ESXi 5.5 nic teaming/LAG with trunking does not but it works on ESX 4.0.  Both are on the same switch. What gives?

  I have two hosts (vhost1 = ESX 4.0, vhost2 = 5.5 ESX) both are configured for the Group and both connected to a switch of 1544 Adtran L3 (named sw01).  vhost1 has been in production for several years with the config below and has been solid as a rock.  I'm trying to reproduce the installation of grouping/collage on vhost2 and it does not work when are associated but will work when you are using a single NIC (with or without aggregation).

  To be more specific about what does not work, two virtual servers have "Network server" (vlan 8) defined as a group of ports. Both physical and virtual servers on the same vlan cannot ping or resolve queries arp for virtual machines on vhost2.    Everything that is sent from a different subnet can connect to the virtual machines on each virtual server.

  So the question is this: why not ESX 5.5 works as ESX 4.0 when the configs are also near identical, as I can make them and they are connected to the same switch?

  Thanks for any input you can provide!

  S

  This is the configuration for vhost1

  switch 1 (sw01)

  SW01 #sho run int port 3

  Building configuration...

  !

  !

  interface port-channel 3

  Description LAG for vhost1

  no downtime

  switchport mode trunk

  switchport trunk allowed vlan 1.8

  !

  end

  SW01 #sho run int 0/23 concert

  Building configuration...

  !

  !

  0/23 gigabit-switchport interface

  Vhost1 vmnic2 vswitch1 description

  no downtime

  channel-group mode 3 on

  !

  end

  SW01 #sho run int concert 0/24

  Building configuration...

  !

  !

  0/24 gigabit-switchport interface

  Vhost1 vmnic1 vswitch1 description

  no downtime

  channel-group mode 3 on

  !

  end

  vhost1

  [root@vhost1 ~] # esxcfg - NICS - l

  Name PCI Driver link speed Duplex MAC address MTU Description

  vmnic0 03:04.00 tg3 up to 1000Mbps Full 78:e7:d1:5f:01:f4 1500 Broadcom Corporation NC326i PCIe Dual Port Gigabit Server Adapter

  vmnic1 03:04.01 tg3 up to 1000Mbps Full 78:e7:d1:5f:01:f5 1500 Broadcom Corporation NC326i PCIe Dual Port Gigabit Server Adapter

  [root@vhost1 ~] # esxcfg - vmknic - l

  Interface Port Group/DVPort IP IP family address Netmask Broadcast MAC address MTU TSO MSS active Type

  vmk1 VMkernel - Server NetIPv4 10.1.8.31 255.255.255.0 10.1.8.255 00:50:56:78:9e:7e 1500 65535 true STATIC

  VMkernel - SAN Net IPv4 10.1.252.20 vmk0 255.255.255.0 10.1.252.255 00:50:56:7 c: d8:7e 9000 65535 true STATIC

  
  

  [root@vhost1 ~] # esxcfg - vswif - l

  Port Group/DVPort IP IP family name address Netmask Broadcast Enabled TYPE

  Service vswif1 - NetIPv4 management 10.1.1.12 console 255.255.255.0 10.1.1.255 true STATIC

  
  [root@vhost1 ~] # esxcfg - vswitch - l

  Switch name Num used Ports configured Ports MTU rising ports

  32 4 32 1500 vSwitch0

  Name PortGroup VLAN ID used rising Ports

  0 3 VM network

  Switch name Num used Ports configured Ports MTU rising ports

  vSwitch1 64 12 64 1500 vmnic1, vmnic0

  Name PortGroup VLAN ID used rising Ports

  Server network 8 7 vmnic1, vmnic0

  Console - management service vmnic1 Net0 1, vmnic0

  VMkernel - server 1 vmnic1 Net8, vmnic0

  On the Load Balancing vSwitch it Hash IP value.

  This is the configuration for vhost2

  switch 1

  SW01 #sho run int 4 port

  Building configuration...

  !

  !

  interface port-channel 4

  LAG description for vhost2

  no downtime

  switchport mode trunk

  switchport trunk allowed vlan 1.8

  !

  end

  
  

  SW01 #sho run int concert 0/17

  Building configuration...

  !

  !

  0/17 gigabit-switchport interface

  Description vhost2

  no downtime

  channel-group mode 4 on
  

  !

  end

  
  

  SW01 #sho run int concert 0/18

  Building configuration...

  !

  !

  interface gigabit-switchport 0/18

  Description vhost2

  no downtime

  channel-group mode 4 on

  !

  end

  vhost2

  ~ # esxcfg - NICS - l

  Name PCI Driver link speed Duplex MAC address MTU Description

  vmnic0 e1000e up to 1000Mbps Full 00:25:90:e7:0e:9 0000:08:00.00 1500 c Intel Corporation 82574 L Gigabit Network Connection

  vmnic1 0000:09:00.00 e1000e up to 1000Mbps Full 00:25:90:e7:0e:9 d 1500 Intel Corporation 82574 L Gigabit Network Connection

  ~ # esxcfg - vmknic - l

  Interface Port Group/DVPort IP IP family address Netmask Broadcast MAC address MTU TSO MSS active Type

  Management 10.1.1.15 IPv4 network vmk0 255.255.255.0 10.1.1.255 c 1500 65535 real STATIC 00:25:90:e7:0e:9

  ~ # esxcfg - road - l

  VMkernel itineraries:

  Interface of network gateway subnet mask

  10.1.1.0 255.255.255.0 subnet local vmk0

  by default 0.0.0.0 10.1.1.1 vmk0

  
  

  ~ # esxcfg - road - n

  Expiration type neighbor Interface MAC address

  10.1.1.1 00:a0:c8:8 has: ff: 3 b vmk0 19m13s unknown

  ~ # esxcfg - vswitch - l

  Switch name Num used Ports configured Ports MTU rising ports

  vSwitch0 4352 7 128 1500 vmnic0, vmnic1

  Name PortGroup VLAN ID used rising Ports

  Server network 8 1 vmnic0, vmnic1

  Management network 0 1 vmnic0, vmnic1

  On the Load Balancing vSwitch it Hash IP value.

  Hello

  Do you share the vmnic for ESXi management and network of the VM?

  Try to follow the steps in this KB: VMware KB: NICs using EtherChannel grouping allows intermittent network connectivity in ESXi

  Trying to team adapters using EtherChannel, network connectivity is disrupted on an ESXi host. This problem occurs because grouping NIC properties will not propagate to the network management portgroup in ESXi.

  When you configure the ESXi host for grouping of NETWORK cards in attributing to the road based on ip hashload balancing, this configuration is not propagated to the portgroup management network.

  Workaround

  Note: to reduce the possibility network loss please change the route based on the hash of IP using this method of balancing load vSwitch

  1. Close all ports in the physical switch team leaving a single port as active.
  2. Change the Route based on ip hash vSwitch and load balancing management Portgroup.
  3. Set up the physical switch port channel.
  4. Activate the physical switch ports.

  Notes: Using this method will avoid a loss of connection when you switch to a port channel. Also make sure that under the properties for vmk portgroup # used for network management you tick the box "Enabled".

• Opening trunk does not open

  I have a keystone of opening that I can not open to rebuild a library which no longer exists.  I have 8 arches and has been able to rebuild 6 of them in .aplibrary.  But two of them does not open and the dialog box tells me that I must update the library itself (which does not exist anymore) to 3.6.  Is there a work around for this?

  I have OS Yosemite.  The opening is 3.6.  I have loaded a disc opening 3.0 to a laptop computer that also uses the Yosemite, but it will not recognize the vault and requires 3.6.  But when I made sure I was refusing to open the safe.

  Any thoughts of an autour work?

  You might tr the following: a vault is essentially an Aperture library.

  Make a copy of your arch as a backup, just in case, then rename it to the extension of your Arch of .apvault to .aplibrary.

  Now launch the opening with the options button is pressed and select the vault in the selector library panel.  Opening may now open the safe?

• VLAN SG200-26-SPA303 does not

  Please forgive me and new small business switches, I am more familiar with IOS. We have recently purchsed a SG200-26 and have several SPA303 with 2 ports. The other component is a Sonicwall NSA3500.

  SG200-26 is an interface to the Sonicwall that interface has a primary school of 172.20.3.x and void interface is 172.20.5.x. I have PST VLAN 5

  I went to "Create of VLAN" SG200-26 and VLAN 5 has also created and under VLAN voice ID is 5.

  Then I went to the SmartPort and assigned GE24 IP Phone + office. It was OK. But when I go to the SPA303 and enable VLANS and VLAN ID 5 get the network initialization. I am able to ping the 172.20.5.1 which is the gateway for the VLAN, but don't always shoot no IP address. I also have a beach DHCP the subinterface assinged.

  I also use the Configuration of Cisco's Assistant. I can see the switch SG200-26 and my IP defined, but it shows no IP address. So, I know that the CDP of telephone to the switch works. Any help would be greatly appreciated.

  Hi James, when you configure anything, you must choose one method or the other. How to read your information is configure you the vlan voice, but you also implement a macro on the port. These can have an effect of the cancellation.

  I do not recommend you remove any manual configuration, you have done on the phone port (s) and enable the vlan auto to take care of this voice.

  In addition, check it vlan automatic voice makes the phone port 1untagged, 5 tag, or whatever is the vlan database is.

  One thing I did notice in the text, this is how to set up the link between the switch and Sonicwall? You must manually configure the link between the switch and the Sonicwall. If your vlan by default is 1 and vlan 5 voice then the link between devices will be 1untagged, 5 the tag.

  -Tom
  Please mark replied messages useful

• several VLANs, vmotion does not work

  I need help in the Setup here in my place of customer. They had 2host cluster and 3 VLAN on a port vmkernel group, where clients are configured to use the VLAN specific (for ex: Guest1/172.1.1.10/ use vLan10, ex2:Guest1/172.1.2.20/ use vLan20)

  I have rebuilt the hosts and cluster yesterday, and I configured the network according to the screenshots I did. Now I see the vmotion is not the case, although all VLAN present them in the host. I migrated manually from the comments and I see inappropriate comments to vlan different and it is therefore not the ping requests.

  Even the host is greater than 93% mem usage, it is not quick vMotioning. What could be the reason? How can I set it?

  It seems that you have attached the same image for both hosts :-) Please, join the correct image and as Andrew said, check the physical switch port where your hosts are connected.

• SG200-26 DHCP feature does not?

  Hello

  I bought a SG200-26 switch and wanted to replace some old Netgear switches with her. With the former, simple Netgear switch everything has worked. With the SG200-26 the only way to get a connection of the switch is to affect the manual IP address. I want the switch to automatically distribute IP addresses and activated the DHCP function in the web interface, but it still does not work. I also tried to restore factory default and set to update to the latest firmware, but it also did not help. I really prefer the switch to handle this. Any suggestions?

  Thanks, Frank

  Hi Frank,.

  200 series of switches is not DHCP Server feature.  The 300 and higher are DHCP server optionally on them, but the 200 do not since it's just a layer 2 switch.

  If you do not have to set a static on your PC you can always plug the switch into a network that has DHCP running.  The switch default values will pull a DHCP address for itself, then you can check your DHCP server for what address he got and use it for the admin access without having to adjust a static on your PC.

  Hope that helps and thanks for using Cisco,

  Christopher Ebert - Advanced Network Support Engineer

  Cisco Small Business Support Center

  * Please note the useful messages *.

• Cisco NAC appliance - after a success does not change users to connect to the vlan propper

  Hello

  I am new to cisco NAC BURNERS and I have to troubleshoot an implementation. It is a real OOB IP gateway configuration. Users can connect to the Pentecost the CCA, but after the connection of this success, they remain on the role not authenticated, as well as on this vlan. I checked the SNMP protocol and seems to work very well. Also, I checked the logs on nac_manager.log and there is nothing surprising, in fact I see nothing about this user or IP address that connects.

  Also the user does not appear on the list of users online on cam.

  Can someone help me figure out how can I fix? version 4.8, I'll post any information requested

  Thank you

  We recently had the problem with Windows AD SSO and Windows 7 clients.

  Would authenticate the XP clients very well, however, Windows 7 clients would not authenticate and will remain just on the authenticated vlan.

  Our question was looking for CASE SSO account, we installed on AD. It only support the encryption, WHICH has no Windows 7 64. We turned off "Use OF THE encryption" on the account authentication UNIQUE AD and re-tested.

  What are the parameters of the port-profile to which is applied the switchport?

  What is the map settings vlan ports trunk not approved or confidence?

• App 5.1 server does not not on different VLANS

  Helloooo

  I just installed a new server and I use the server application. Everything seemed to work fine until I moved my iMac to a VLAN different. Profiles and update settings do not push to the iMac and sit at a stadium in waiting. Also to register the new iMacs on the server I get to the login server window and it crashes it and does not authenticate. Screen opens by saying that I can open a second window and registration. When I try to register, I get an unknown error and that it fails. It seems timeless. I tried to change a lot of settings prescribed by other users, but nothing helped. Someone at - it advice on what could be the problem.

  See you soon

  Sean

  Hello

  I took the easy on this way and bring a USB ethernet to my mac so that I have two physical interfaces. An in each VLAN.

  There are other ways to do this, and this is a good article:

  https://blog.Pivotal.IO/Labs/Labs/using-deploystudio-across-Subnets-a-Path-Not-t Aken

  Kind regards

  Erik

• If vlan native between Trunk ports not configured so what happens?

  I have a network where two ports of junction are allowed vlan 9 but not native VLANs configured. will be affect performance?

  by default the vlan1 is configure the vlan native to assign a vlan on the interface different native

  switchport trunk vlan native xxx

  HTH

  Richard

• VLAN and the SSID does not not in the Web Interface

  We have a couple of APs which do not show the VLAN and via the web interface of AP SSID.  If you go to the SSID Manager page in the web interface, the page rises but doesn't show any SSID configured.  It goes the same for Services - Vlan.  This page appears but does not show in any VLANS configured.  If you telnet to the APs, you see the mssid listed and all the SSID interfaces.  The SSID on the access point is functional and working.  It is just so hard to use the web interface for these APs.  I tried to compare configs running on APs where the web interface does not show this and APs that it shows, but cannot see any differences.

  Thank you.

  Have you tried with different browsers?

  Nicolas

• VLAN to the internet does not.

  Hello

  I just the 6248.

  VLAN 1: 10.0.1.1/24

  VLAN 300: 10.254.0.1/24

  Gateway: 10.254.0.10 //residing on VLAN 300

  I can ping to the gateway of the VLAN 1, I can ping hosts on VLAN 1 from VLAN 300, but I can't access internet from VLAN 1.  VLAN 300 has not all hosts except the entry door.

  VLAN 1 is the default VLAN with management moved to 255 VLANS.  VLAN 1 is able to route.

  VLAN 255 is the management VLAN without routing.

  I do a tracert and I get this:

  C:\Documents and Settings\chris > tracert www.yahoo.com

  The route to www.yahoo-ht3.akadns.net [69.147.114.210]
  with a maximum of 30 hops:

  1<1 ms   =""><1 ms    ="" 1="" ms ="">
  2 1 ms<1 ms   =""><1 ms ="">
  3 * the request exceeded.
  4 ^ C

  Here is my current setup.

  ! Current configuration:
  ! Description of the system 'Dell 48 Port Gigabit Ethernet, 2.0.0.12, VxWorks5.5.1'
  ! Version of the software system 2.0.0.12
  !
  Configure
  database of VLAN
  VLAN 255 300
  output
  location of the SNMP Server «*»
  SNMP Server contact «*»
  hostname "DELLP_PE_6248-01".
  battery
  1 2 Member
  output
  the IP 10.0.0.1 255.255.255.0
  IP address vlan 255
  IP routing
  IP route 0.0.0.0 0.0.0.0 10.254.0.10
  router RIP
  by default metric 1
  output

  interface vlan 1
  Routing
  IP 10.0.1.1 255.255.255.0
  IP rip
  no ip proxy-arp
  output
  interface vlan 255
  name of "management".
  output
  interface vlan 300
  the name "Temp".
  Routing
  IP 10.254.0.1 255.255.255.0
  IP rip
  no ip proxy-arp
  output
  level of e6b391f96478438ce8fcacd4d0a695fb user name 'admin' password encrypted 15
  line console
  e6b391f96478438ce8fcacd4d0a695fb encrypted password
  output
  !

  interface ethernet 1/g1
  switchport access vlan 300
  output
  activate e6b391f96478438ce8fcacd4d0a695fb encrypted password
  output

  Thanks in advance.

  
  

• DHCP relay does not not in in-band mode

  Hi Faisal,.

  wireless client does not have dhcp via a CAS server server ip address,.

  Here's the scenario,

  1. inband case network configuration:

  Trust interface (for protected network)	Untrusted interface (network management)
  IP address Subnet mask Default gateway Set the management VLAN ID: Through VLAN ID managed network	IP address Subnet mask Default gateway Set the management VLAN ID: Through VLAN ID protected network

  2. wireless customers in vlan rogue who is 104 and I traced the vlan 104-400 (trust vlan)

  VLAN vlan untrusted trusted

  140                                                        400

  3 run subent

  ip subent                                                                               vlan

  10.161.136.5 / 255.255.248.0 140

  10.161.136.5 is the trusted ip subnet VLANs 400

  4. Enter ARP is not configured

  in switch, reliable and trusted ports are configured as port trunk and permit reliable and trusted VLAN respectively.

  When we move the client VLAN 400 wireless manually obtain ip address but when wireless client is in vlan 140 its not get ip address and in the configuration of the approved switch and ports not reliable are trunk port and using the vlan native is 1

  WLC pass port is port trunk and allowed for all the VLANS

  do I need to configure the ARP entries or what other configurations are required to work CASES like a DHCP relay.

  Thank you

  Laxman,

  Three things:

  -If it's in VGW, approved and non-approved interfaces must have the same IP address

  -Uncheck "the passage through the VLAN ' on both sides

  S ' away from VLAN 1 if possible!

  HTH,

  Faisal

• Junction UCS ports worksheet does not, no integration of WWW.

  Hello!

  Key:

  VLAN 200 - all the 20.1.1.0/24

  VLAN 201 - 20.1.2.0

  VLAN 202 - 20.1.3.0

  VLAN 203 - 20.1.4.0

  VLAN 204 - 20.1.5.0

  Just migrated some UCS, HCI SuperMicro and physical servers above 5ks/fex again 9 k column spinal/leafs Cisco ACI running.  Worked well on the 5ks, access ports if necessary, logs allowing VLAN 200 to 204 will stuff UCS and SuperMicro.

  Before I continue, note I am NOT currently any VMM integration, just try to get the same trunk ports to the beach above of VLAN on ports leafs. ***

  Thus, servers physical and other access ports work perfectly.  The links of the trunk of the UCS and SuperMicro don't seem to work right.  By focusing on just the UCS, I can see the entry ARP for the UCS himself, but no resolved IP address.  In addition, I don't see any MAC/IP addresses the Server Blade, or anything else.

  For static bindings EPG, I tried marked (assuming that the law) and not signposted.  ENCAP different VLAN (current vlan-203) but nothing seems to work.  Side of a LLDP and CDP UCS active as I was.

  Speaking of VLAN, I built 5 EPG to do this, each corresponding to a function from one of the 5 VLAN above.  However, the UCS trunk links should allow all VLAN 200-204.  I have a jump on 20.1.2.5 server that cannot call the 20.1.2.x IPs who also live in the UCS, because there are certain types of disconnect to the where the ACPI cannot see in the links of the trunk at all.  I don't know if it's related or fabric EPG associated config.

  I would be very happy to provide additional information, because I'm dead in the water.  Thank you very much.

  Josh

  It depends on if the non - UCS hosts are on the same sheet or not.  You can map an EPG on different ports with some tag and others do not.  There are the limitations when you want to have multiple ports on the same sheet as however no marked.  A single VLAN ID cannot be the tag & unidentified on the same sheet. Even when we put a static as path "unidentified, or 802.1 p ', still need to assign a VLAN unique traffic (can not also be VLAN 201).  It's really a VLAN arbitrariness to the fabric only.  Any evacuation traffic or infiltration of the connected device would send/receive traffic without a tag VLAN.

  Example let's say you have a UCS connected on port 1 and a re-usable on port 2 (same sheet).  You can set EPG - A 'tag vlan 201' for the UCS, and "untagged vlan-205" ports for re-usable connected ports.  Even if the program is different, it does not matter.  The two ports will land in the EPG even at the end of the day and be able to communicate.

  Make sense?

  Robert

  Here's what the config would look like. * Note that my pool VLAN ranges from 200-205, since ACI must allocate a VLAN of the pool especially for unmarked ports (System requirements).  As your hosts are directly connected to the canvas, the VLAN is arbitrary.  We just want that they arise in the EPG even.

  Capture1.jpg

  

  capture2.jpg

  

  capture3.jpg

  

  capture4.jpg

  

• Cisco SLM224G VLAN Trunk Help! -&gt; Problem solved!

  Hi, I have a few difficulties of implementation of the switch, I can't understand how to configure the network for VLANs created port. I have configured under management of VLANS, VLAN 10 and 20, I asigned ports e1, e2, e3, e4, e5, e6 with 10 PVID and e7, e8, e9, e10, e11, e12 with 20 PVID and the rest to defaul 1 PVID, frame SD = All + infiltration on filtering. Under port to VLAN-> VLAN10-> ports e1, e2, e3, e4, e5, e6 Tagged + e24 tag (I want this to be the trunk) and the tag VLAN20-> e7, e8, e9, e10, e11, e12 Tagged + e24. Theats all that I set up according to the SLM_Admin_Guide.pdf and I have connected the e24 (trunk port) to a Pf meaning Server (the server is configured with the same VLAN ID as on the switch), please someone tell me how to set up the trunk? I know that there is no option in the Port settings to define 'Access' or 'Trunk'... until this means? that the SLM224G does not support the VLAN Trunk? I saw some screenshots with the Linksys SLM224G and he had 'Access' or 'Trunk' setting... and Cisco does NOT work.  Help!

  Hello

  Interesting, I see two different GUIs in your screen capture, it looks like two different computers. :-)

  But the big brother of the SLM, the series SRW and I am about what follows to the SRW series, because I do not have a SLM in front of me, I had put;

  Step 1. the port settings interface return, leaving the PVID to 1 then do scroll down and save the option.

  Step 2.  On this "ports setting photo GUI, you have, I would put the switch ports to shared resources in mode Trunk. If the port must not be tagged in the VLAN 1 only, then I leave the setting the port mode 'access '.

  (Access mode allows a port belong only to one VLAN no marked only).

  (shared mode allows the switch port belong to several VLANs marked, but still unmarked in one vlan only usually the vlan by default)

  Step 3.  So I goto the "Vlan to the port' tab, Tagged for ports beloning to vlan 10 then do scroll down and save the option."

  step 4   So I goto the "Vlan to the port' tab, Tagged for ports beloning to vlan 20 then do scroll down and save the option."

  By default vlan1 in most SRW series brother would then be not identified on all ports and vlan10 and vlan 20 could be labelled on the appropriate ports.

• VM PortGroup does not

  Hello, first of all, sorry for my extreme of perfect English.

  I am facing a weird problem here, after adding an ESXi host in a cluster and don't configure it like all his peers, one of the Portgroup VM does not work correctly, when DRS or my right hand puts a VM use on this new host, the virtual machine gets no connectivity.

  I double checked the configuration of the network on the ESXi, I triple check the configurations of ports on the switches of medical examinations, as its basically the same surrounding ESXi/ports, it was easy to see that it's all sounded good.

  Then why am I here and not replacement of network adapters or change the ports of the switches? Well, when I add a VMkernel port on the same vSwitch, using the same local network as the defective Portgroup VM VIRTUAL, it is simply works.

  If anyone has an idea...
  

  Post edited by: Cove

  You have the vlan 1 on the trunk ports native? If vlan native then, together in one vlan unused ID if you force tagging vlan 1 traffic as well. Always good practices on the trunks of esx