SG500 problem - 52p with a port.

Similar Questions

• Communication with Serial Port

  Hello

  Hi I have a request that I should communicate with serial port...

  Its works perfectly if gives you all parameters to com as constants (pls hav a look @ codea).

  But I want to read the port number and baud RRSP file text. When I changed the encoding in serial number

  setting, I was not able to find the number rate.it and port baud displayed as the size of memory buffer. I think that the way I connected the baud rate and port number to the clusture may be a problem (pls see codeb). How can I solve this problem?

  Thanks in advance...

  Again, the point of connection to the Central Terminal is not not to define the values contained in the cluster - just the logical structure of the cluster. The data that appears in the cluster from the budler will reflect the data that you read from the file. Try it.

  Mike...

• Printer LaserJet 4100: Should which cable I for Laserjet 4100 connected to the laptop with USB port

  I have the HP Laserjet 4100 printer. I bought a new laptop with USB ports.  What type of printer cable I need to connect the printer to my laptop? Is there some kind of printer cable adapter, or something else that will do the trick?

  I have the same question about my HP Laserjet 1100 printer.

  Thanks in advance for your assistance expected.

  If I remember correctly, the 1100 uses a cable "C", alias MicroCentronics.  Have never seen an adapter for that one.  On the 4100, you can get a USB to parallel adapter.  They are pretty cheap and available at most CESS (Consumer Electronics Super Store) as Best Buy.  Staples and OfficeMax/Office Depot should also wear.  Online is cheaper if you have time to wait.

  The thing with these USB converters is often must 'install' the cable first.  In other words, connect it to the laptop, then wait so he could install, then connect the printer.  Depending on your operating system and if you have correct updates that can be almost instantaneous, and you may not even see it pop on the screen.

  Best idea is that since these are obviously not portable machines, connect them to your router via a network card.  I had the 1100 years and used a cheap 170 X.  I know most recent are available which are faster.

  For the 4100, see if you can retrieve a Jet Direct 620 unit on eBay.  Probably less than $50 and sometimes even as little as $25.  Stay away from the 600, 510 or 615 cards.  Low or as the 600, they can leave your network open to hackers.  No need to get Gigabit cards as they will be well above what the 4100 can handle.

  Now, two of these old devices, processing power and memory can be a problem.  Never try to print documents online.  Save them on your laptop, and then print.  You will probably get communication errors if you print directly from IE or FireFox.

  If the 1100 does not die, not even worth fixing.  Put into a Fuser is a nightmare.  The 4100 will probably work for another 20 years if you keep to clean and replace the rolls before they cause jams.

• Having problem using proxy on port 443

  Greetings to everyone.

  I have a strange problem.
  First of all, let me say that this is not the problem of Microsoft, but I tried so hard that not not to post my problem here, because it's a Microsoft forum, but I could not, I tried the days to fix it myself, but not lucky at all.
  My friends and I are using a proxy to a specific server. Nothing we have a problem, except me.
  And let me say that we use a program called Proxifier. Although you can use the proxy without this program and it works fine (using the properties of Internet, LAN settings), except for me!
  I use two PCs and a laptop.
  The proxy and the Proxifier works very well on my PC and laptop.
  However, I used to use this program in another PC as well, and it worked very well, but not more.
  Here is what happened, I don't have that use the PC for more than 8 months and when I came back to it, it didn't work.
  No change at all.
  And the strange thing is, proxy and Proxifier works fine when I start Windows in Mode safe mode with networking. And that means that there is a problem with software, right?
  I don't know what could be the problem, turned off firewall and anti virus (ESET V6 more Malwarebytes') but no luck.
  Please, help me if possible.
  And something important, I can connect to the proxy server, but I can't connect to any Web site using the server, here is the error I get on Proxifier:

  [50:59] from: test 1: connect to the Proxy Server

  IP [50:59]: REMOVED

  [50:59] connection established

  [50:59] Test passed.

  [50:59] from: Test 2: connection via Proxy Server

  56: [00] error: connection to the proxy server was closed unexpectedly.

  Please make sure that the proxy server protocol and address are correct.

  [00: 56] Test failed.

  [00: 56] test completed.
  And I get this error after waiting a few minutes not instantly...
  Plus, I have tried a different proxy, the same result, connects to the server, but not to a Web site through it.
  Sorry, just one more thing, I am able to use Freegate (if you know what is it), a free software, but it is too slow, I mean to refresh a page 10 times and he can open it!
  I really need to use the proxy...
  I appreciate any help, thanks.

  Oh God, I can't believe it!

  After hours of train and think, I solved the problem.
  The problem was an option on ESET.
  No wonder why the boot didn't work, ESET ran on boot.
  I stopped ESET service manually rebooted. and the proxy was working fine. But on my other PC and laptop and even my friends, we all use the ESET without this problem.
  On the problem, ESET has the port number 443-scanning, and to tell you, this is a default option.
  Here is the solution:
  Open ESET Advanced setup (simply by pressing F5), click HTTP, HTTPS(don't develop it), on this last field "Ports used by the HTTPS protocol", remove the ports you have problem with, click on OK and you're done.
  Sorry for the inconvenience.
  See you soon,.
  Amin.

• I have problems to make my battery charged, because the cable does not have a link solid with the socket of the phone.  The problem seems compatible with a lot of cables, so I think the problem is with the phone. Can it be fixed?

  I have problems to make my battery charged, because the cable does not have a link solid with the socket of the phone.  The problem seems compatible with a lot of cables, so I think the problem is with the phone. Can it be fixed?

  Probably there is debris and dust in the decision-making of the lightning.  Serve with compressed gas canned (NEVER orally).  If this doesn't help, try electronic contact cleaner has a q - Tip.  Finally, take it to Apple.

• Problem starting with Satellite A210-183

  Hi to you all.

  My name is Costis and I have a starting problem with my laptop. The laptop runs Vista and it was bought in November 2007.

  I have the following message:

  "Windows has encountered a problem communicating with a device attached to the computer.
  This error can be caused by unplugging a removable storage device, such as a hard drive or a cd-rom drive which is a failure.
  Make sure that all removable storage is properly connected, and then restart your computer.
  Status: 0x00000e9
  Info: An unexpected i/o error has occurred. "

  Can you help me how to do?

  Thanks in advance,
  COSTIS

  Hello

  What devices are connected to the machine? Some external HDD´s or DVD readers? Would be interesting to know because this error is caused mainly by external media/devices that are not properly connected to the laptop or a malfunction.

  I recommend to unplug everything from your machine and check if the error reappears. So I would suggest to backup all of your important data and retrieve the machine completely (maybe it s a related problem of the software).

  If that's not enough then come back and talk to us more this question.

  Welcome them

• HP Pavilion Notebook-15-p108tx: problem connecting with specific programs

  Hi, I had problems connecting with specific programs recently. I'm still able to communicate online through web browsers. Mozilla Firefox works fine, but Google Chrome still has some problems loading of specific pages or they don't load at all. The main programs I am having difficulties with are mainly games platform programs like Steam, Battle.net, and League of Legends, and I'm unable to go online or to connect to their servers.

  I never had no problem connecting like these last two years that I've owned my laptop, until recently. I think it was the 6th or 7th of may these problems started.

  I updated my drivers and was constantly check to download the most recent. I don't know if it's my internet provider, but I was also constantly check the State of the network to ensure that the services are very good.

  If anyone else has this problem and if there are any suggestions that you think could help solve this problem, it would be appreciated.

  Thank you

  Jasper

  Hi Jasper,.

  Thank you for the update. I think that your computer have a rootkit infection. Most of them were inside of the Chrome Extensions.

  Here's what you need to do.

  Open chrome

  Click on the Menu bar in the upper right

  Click more tools

  Click Extensions

  Please search for suspicious extensions that does not belong to the computer, especially ads. Once you identified, simply click the trash can icon then Chrome close then reopen it again to see if you can connect to your desired game. If this isn't the case, then proceed as follows.

  Manual removal of suspicious files (if you are uncomfortable with it. If this is not the case, then run System Restore from safe mode with command prompt)

  Manual removal (I miss the old days of MS virus removal )

  Go to RUN type %temp% , and then delete all folders by pressing SHIFT + DELETE

  Go to Control Panel and then locate all the apps that you think a form of ads

  Go to safe mode with network. Run Malwarebytes in that State

  Then run Tweaking tool to fix everything that has changed since your computer

  http://www.Tweaking.com/files/setups/Tweaking.com_windows_repair_aio_setup.exe

  If your not comfortable with the troubleshooting steps may perform the system restore on the day, it was working fine.

• Many people have a problem closing with El Capitan? Apple plan to fix this?

  Many people have a problem closing with El Capitan? Apple plan to fix this?

  You must describe your shutdown problem otherwise, we can only guess what you're talking about.

• Problem-solving with HP2311x and ProBook6455b

  Hello

  I have a problem-solving with portable HP2311x and ProBook6455b.

  Maximum resolution is 1600 X 1200

  Current display driver is ATI Mobility Radeon HD 4200

  However, my HP monitor supports the 1920 X 1080.

  I used only the external monitor without using the laptop monitor and the maximum resolution is always to 1600 x 1200.

  I also downloaded the drivers recommended by HP, but it does not solve the issue.

  I also tried with the drivers provided by AMD, but I get still more low resolution (1280 x 768) because the driver software detects is ATI Mobility Radeon HD 4250

  When I try to use the AMD Vision Engine Control Center stops unexpectedly

  I have conteacted
  Portrait Displays, Inc..
  http://support.portrait.com

  But they suggested me to contact HP because they were not able to solve my problem.

  Any help will be appreciated.

  Kind regards.

  I understand that you are not able to use the full resolution of the monitor even when the screen of the laptop is out of the question.

  Ensure that the system has the right driver for the monitor found here.

  You can try the support business forums as it appears that the two components are business models.

• problem scanning with keithley 2420

  Hello

  I'm having some trouble to configure the Keithley 2420 to sweep a range of Volt and measure the amps in a cell.

  The vi attached check the polarity of the voltage, then measure the short circuit current and then performs a scan.

  The program runs, but scanning seems to measure resistance and outdated.

  Any help would be greatly appreciated!

  Incase anyone reads this, the problem was with the drivers Keithley 2400 do not turn off simultaneous measurement mode when you set up the type of measure. Even if I set the type of measure amps, he was still measuring ohms.

  I still don't know why it uses default ohms.

  Anyway, I solved this problem by using the ENS:FUNC:CONC OFF command with the Instrument i/o assistant after having used the driver concerned of Keithley VI to set all other settings.

• for windows update make me number error msg: 0 x 80240036 and solve this problem poblem with fixit get msg w xp sp3 rendered and nework Framework 2 or lator should be installed pls can help you

  for windows update make me number error msg: 0 x 80240036 and solve this problem poblem with fixit get msg w xp sp3 rendered and nework Framework 2 or lator should be installed pls can help you

  See your other thread the same. http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-windows_update/to-make-Windows-Update-am-getting-MSG-error-number/3f579859-ecb0-408D-9db3-804044a21fb7

• Go off & on several times before the monitor turns on. Comp seems to start OK but the problem is with the screen.

  Original title: XP start help please...

  ... are to be turned off & on several times before monitor lights. Comp seems to start OK but the problem is with the screen. Do I have to make a boot disk & if so - HOW?

  Hello

  ·         What is the brand and model of the computer?

  ·         You get the error message?

  ·         Did you check the connection of the cable to the monitor?

  ·         Have you tried to update to the latest graphics card and motherboard chipset drivers?

  First, try to connect your monitor to a well known PC, maybe the old laptop that you use now. If the monitor works, the problem is with the video card in your PC. If the monitor does not light, the monitor. It is usually cheaper to buy a new monitor that in order to be an old repaired, unless the monitor is still under warranty.

  Try connecting a monitor well known to your PC. If the monitor works, your old monitor is fried and needs to be replaced.

  If your monitor works when connected to another PC, the problem could be your video card. First, and then you turn on your PC, the power and cooling case fans run they. If they do not, it could be the power supply.

  Then, open the computer case. Before you do anything inside, unplug the power supply.

  IMPORTANT! Touch any metal part of the computer case to connect to the PC. A single static spark can destroy computer circuits.

  If the video card is the type of card that plugs into a slot on the motherboard, remove the screws or attached at the top of the card, remove the card, to manipulate the card by the edges to avoid disturbing the circuits on the card, carefully and re - install the card. Sometimes simply reinstalling the card corrects the problem.

  If this does not work, replace the video card with a card of similar type. Perhaps now is the right time for an update of video card.

  If the video card is integrated into the motherboard, you can install a new card in one of the PCI slots on the motherboard. When the PC starts for the first time, go into the bios and disable the onboard video.

  Resources for troubleshooting problems in Windows XP

  http://support.Microsoft.com/kb/307960

• (Windows XP) Huge problem associated with Windows XP Signature

  Hi all

  Im having a problem @ home in my PC.

  I activated my Windows XP Activation already. & then I did for most all the total of updates is like 100 +.

  & then I try to install the driver for my ATI graphics card, while installation that I encounter this problem.

  He said,

  Window XP Signature has not be installed or something... then he said, Countiune Installation can damage your computer for blah blah blah

  IM currently are not @ home, I'll reach the homepage in 5-6 hours away.

  I'll post a screenshot of what happens. But if someone get what I say, then please respond ():

  NVM solved (: I remember ATI you have a problem associated with mircosoft then Yes (: thought thanks))

• How VLANs ' IP subnet ing works with based port of VLAN (series N2000 and N3000)

  Hi all

  I have a small pile of x N3024 2 acting as my heart L3 with a lag of 2 x 10 g down to a stack of x N2048 5 acting as L2 switch for my PC workstations.

  Workstations are that all on the port assigned VLAN 10 (switchport access vlan 10). I have a bunch of developers who want to access without restrictions more or less to assign random IP addresses for their VM (Virtualbox and VMware) Workstation.  As you can imagine, I would like some control over this situation.  the powerconnect guide I described features of subnet IP VLAN but does not seem to enter in how it works and interacts with the port actually function vlan assignments.

  What I currently have is the VLAN 10 assigned to a segment that support the subnet 172.100.x.x which dates back to our base of L3 for routing to other segments. What I want to do is to configure the VLAN based on IP and then load the dev is to config their VM with another IP range, say 10.10.x.x.

  Theory here is, I set the L3 core with say 20 VLAN and an IP to register in L3 path between subnets and then configure the battery switch L2 workstation with IP - based VLAN to recognize 10.10.x.x and separate on VLAN 20.

  However, I think the simplified here question is if I have a nail up to 10 ports VLAN, will the than basic work IP subnet VLANS as I want only it? Or, I need to create a subnet IP VIRTUAL local area network for the two IP ranges? I have to remove the assignenment VLAN per port and are based entirely on the treatment of subnet IP VLAN?

  If there is a better RTFM on this topic you can tell me I would appreciate it

  Thank you!

  I ended up calling specialists... great Dell technical support here.

  In fact, the IP based VLAN works very close to what I want to achieve. Missing from the user guide is that the port needs to be in the mode. Ports using switch port mode and bound to a VLAN just didn't work... probably because the vlan IP based did not differ from the port binding. Dell support has suggested to use the trunk mode, but my answer is finished using the general mode; any traffic not referenced, PVID located my usual LAN vlan ID and acceptance of port traffic of new vlan based on IP. In this way, I'm able to have a physical host DHCP on the corporate LAN and a virtual machine on that host to bind to a different subnet which is then isolated in the new NAV based on IP.

• Windows has encountered a problem communicating with a device connected to your computer. Status: 0xc00000e9.

  * Original title: 0xc00000e9

  Hi all

  I had a problem - would be great if someone could help me!

  =====

  Windows has encountered a problem communicating with a device connected to your computer.

  This error...

  File: / Boot/bcd

  Status: 0xc00000e9

  Info: An unexpected i/o error has occurred

  ==========

  I press ESC = exit or enter = continue it tries to start, but eventually back to the black screen. So I can't pass this screen. I do not of hava a recovery for Windows disk... And the laptop is a Sony Vaio with Windows 2008. A couple of days, I have connected to my work through the laptop environment and forgot to close - battery went down--and now this...

  Can anyone help?

  Please see the message (response) by Afsal Taher:
  http://answers.Microsoft.com/en-us/Windows/Forum/all/new-computer-running-Windows-7-unexpected-IO-error/46b4fc7a-9a83-4db2-9a00-dca512797e61