Shell command authorization

Similar Questions

• Problem with shell command authorization

  I came across this issue with ACS 3.1 and 3.2 of the ACS

  A shell command authorization set is created under the profile shared with the following components:

  Unmatched orders: refuse

  Permit of unmatched Args: UNCHECKED

  The order authorized is 'show' with the Arg "worm permit", "allow the interface" and "allowed to run.

  This permission set is then applied to the group, under the option "Assign a Shell command authorization on any device on the network."

  Select this group option is set to 'Max privilege for any customer of AAA, level 15.

  This configuration is then tested against two IOS switches, with orders from aaa as follows:

  AAA new-model

  AAA authentication login default group Ganymede + local

  the AAA authentication enable default group Ganymede + activate

  AAA authorization exec default group Ganymede + local

  AAA authorization commands 15 default group Ganymede + local

  The problem I have is that when a user who is part of this group connects, it can issue commands such as see the worm, see the race and show int just as I would expect. Any command that does not begin with a show... is denied. However, other show commands that do not appear in the arguments of will work, so that some don't. For example, "show arp" and "vlan" worked, while "show accountants ' and 'buffer' does not. What Miss me?

  commands that work without explicitly set them are of privilege more low level 15... for example; "show arp" is a command of Priv-1, so it is execuatbel without permission of command as you do not permission to order for private-1.

  Router > sh priv

  Current privilege level is 1

  Router >

  Router >

  Router > show arp

  Protocol of age (min) address Addr Type Interface equipment

  Internet 10.1.5.2 24 0000.abcd.abcd ARPA Ethernet0/0

  Internet 10.1.5.3 - 0003.abcd.abcd ARPA Ethernet0/0

  Router >

  Router >

• How to activate 'Shell command authorization games '.

  Hello

  I use aaa on Ganymede to check the user to active directory ms.

  I set up a new "Set Shell command authorization" see the attachment for more details.

  But it does not work. So, I just want to check if the use of a command works or not.

  You can see in the file attached, I tried something with the command 'show '.

  But if I connect I am still able to use "view aaa servers" example, but in the 'show' commandbox I asked the agrument "refuse the aaa" inside.

  Why doesn't this work?

  Thanks for the help

  BB

  BB,

  Not sure why you want to do it this way. Trick here is to give all users a priv 15 and then set the permission command, defined according to your need.

  Overlooking priv 15 does not mean that the user will be able to run all the commands. You can set permission set and allow that you want specific orders, the user should be able to run.

  So pls rate this help

  Kind regards

  ~ JG

• Help ACS shell command authorization

  Hello

  I wanted to only allow users to use the command interface. But when I have enabled terminal config of ACS shell command, all commands are allowed. How can I limited users having only permission for command interfaces?

  Thank you

  Two things may be wrong

  (1) you do not have the following command on your AAA Client:

  AAA authorization config-commands

  (2) you have clicked on the 'unmatched orders' = allowed radio option in ACS, take a look on:

  http://www.Cisco.com/en/us/products/sw/secursw/ps2086/products_configuration_example09186a00808d9138.shtml

  Concerning

  Farrukh

• Arguments using Wild-Card in Shell command authorization

  The Shell permission command Set allows the use of wild-card?

  For example, according to command shell permission, what can I put the arguments if I want to enable the command show interface fastethernet 0/1-24 run?

  And also, what should I put in as argument for a ip address if I want to allow "ping x.x.x.x"?

  Thanks in advance.

  Hello

  There are two wildcard characters used under authority of command Shell is the first ' ^ ' sign which designates anything that comes after this is accepted and the second wildcard is ' $' which means anything that is before. In your case, you can use

  Interface FastEthernet 0 1 ^

  and

  Ping ^.

  These commands allow access each Fastethernet and ping to an IP address.

• ACS - configure the authorization of shell commands to work under the configuration mode (conf t)

  Hello world

  I'm trying to set up a shell commnds set orders (including t conf mode) will be allowed, with the exception of administrative commands, such as writing, copy, admin, format etc.

  He worked for the commands in privileged mode (most) (such as writing and copy), but did not order t conf mode. It is important to prevent users to perform the ' write for the "and" copy run start "commands, for example.

  Here is the entry in the series of command shell (Partial_access) approval:

  Unmatched orders: permit

  List of commands:

  Admin

  copy

  delete

  do

  format

  To write

  (Relevant) group settings:

  V - shell (exec)

  Privilege level of V - 15

  Shell command authorization set

  Assign permission to command Shell Set to any device network - Partial_access (group name)

  I use CiscoSecure ACS version 4.2 (0)

  Thank you

  Lior

  Hi Lior,

  Please make sure you typed in the AAA client, the following commands: -.

  AAA authorization config-commands

  Thanks for posting your AAA client configuration via "run sh |" I have aaa "and if possible your configuration of privilege"

  HTH

• Command authorization Config 3.3 ACS

  Hello

  I want to allow a user only add/remove the roads on a router. The shell command authorization works very well. But when the user is in configuration mode, it can start with any order!

  Debugging says:

  1w2d: AAA/AUTHOR: authorization config command not enabled

  How can I activate this and how/where can I he set up the GBA?

  Thanks in advance

  GBA just allow the user to enter the command 'road' as if you have any other shell command that they are authorized to do.

  On the router/NAS, you must tell him specifically that you want authorization for config commands with the following:

  AAA authorization config-commands

  Note that the format of this command changes slightly on different versions of IOS, but if you "aaa authorization?", you will be able to understand.

• series PIX command authorization

  Hi all

  can someone tell me please the use of GBA pix command authorization. I understand the use of a shell command authorization.

  I'm sorry if the question is too dumb. I am completely new to this sector.

  Thanks in advance.

  concerning

  Kirti.

  Pix command authorization set was designed to set up approval order with PIX/FWSM, as shell pix did not differ for IOS, but at the launch the actual code, PIX/FWSM seems to work correctly with the auth command sets the shell.

  So no one is really interested in using shell Pix more, more to watch new codes of pix it seems that developers are more likely making Pix Shell same shell IOS, so even if they stop PIX command sets in the next version of ACS I will not be surprised.

  ~ Rohit

• The AAA command authorization

  I have an ACS 4.0 device. In the shell command authorization set section, you can define authorized or rejected orders (see) and arguments (running-config). I'm limiting users to a set of specific commands. One of the commands is "exit". To my knowledge, "exit" has no arguments. If I add 'Quit' as a permitted command but nothing come to the section of the argument, I get the authorization failed on the router. If I select "unparalleled stay args" (of output), the authorization is successful. I would prefer not to select "unmatched args to stay." Is there an argument for "out" I'm not aware of?

  Hello

  Try this,

  exit - permit

  represents returns the key.

  Kind regards

  Prem

• Specific shell - ACS command authorization / GANYMEDE + on 2900XL

  Hello all-

  I was struggling with a particular issue here. I am running ACS 3.2 and tries to implement secure access to my switch. I have 'students' of my University I want to leave running specific functions, i.e. change the vlan port and write in memory, etc.

  I created with success the piece of the authorization, and my test account can connect. I have successfully assigned a privilege level of 7 also, that gives me a look of default base rights. Accountants strives also, indicating connections and commands me to come home.

  I want to do is use ACS to allow a particular group of controls, so I can change if needed in one place (ACS) and I not touch + 400 devices. ACS says can be done, but it doesn't seem to work. I created a Shell command group and specified commands, no luck. Even if I change the 'unmatched orders' rocking 'allow' (which should allow all orders, right?) it does not yet allow all orders. I added the Shell command group for the group, of which students are members...

  My AAA commands are as follows:

  AAA new-model

  AAA of default login authentication group local Ganymede +.

  Group AAA authorization exec default local Ganymede +.

  AAA authorization commands by default 7 Group Ganymede +.

  AAA accounting exec default start-stop Ganymede group.

  orders accounting AAA 7 by default start-stop Ganymede group.

  orders accounting AAA 15 by default start-stop Ganymede group.

  AAA accounting system default start-stop Ganymede group.

  Any ideas? Any thoughts?

  Thank you!

  Michael

  QU.edu

  Michael,

  You perform permission to order order that exist with a privilege level of 7. By default, the configuration commands have a privilege to 15. There are two ways you can go about solving this problem. The first would be to authorization of installation for level 15 command. The second would be to change the privilege level of the commands that you want your students to be able to run level 15 at level 7. This can be done with the command of privilege. Here is a link that shows the use of the technology locally within the unit. http://www.Cisco.com/warp/public/480/Priv.html

  I don't know if the ACS can push the configuration of the device on a per user basis, so the first option may be your best bet. Be sure to allow access to all controls for yourself.

  Steve

• How can I use Cisco ACS to save Shell commands

  Hi guys, pleeeease how can I configure Cisco ACS to do command authorization on my Cisco 3660 router. I get the accounting logs and authentication but no newspaper that show orders issued by users - shell and it's the most important paper that I need. I read materails and download articles on the site of Cisco... but the thing is still does not give me the papers.

  I have these lines on my router:

  ...

  AAA authorization config-commands

  AAA authorization exec default group Ganymede +.

  AAA authorization commands 15 default authenticated if

  AAA authorization network default group Ganymede +.

  ...

  It's funny, when I turn on debugging of the authorization of the AAA on the router, it shows me every command being sent by the user on the debug log. But nothing shows under Administration TACAC + on the Cisco Secure ACS. What is responsible for this?

  *****************************************************

  I installed the trial version of the Cisco ACS 90 days and made all necessary settings and I have to say I like what I see already. I'm opening moves to recommend the product to purchase. Thank you guys, I got about the features of this ACS software through this forum, keep up the good work. I recommend the software for those who need to have adapted to the management reports Security Audit logs.

  If I understand what you're asking correctly, the answer is not in the authorization, that it is in accounting. I set up on my routers and send to ACS orders that level 15 privilege users enter on the router.

  orders accounting AAA 15 by default start-stop Ganymede group.

• App, opening a file via windows shell commands: "a device attached to the system does not work.

  Hello!

  I hope that someone here will be able to throw some lights on my question, if I post this is the wrong place please let me know because I was directed here (which forum? ). OK, I support and develop custom applications. An older application especially written in Delphi allows users to attached documents (pdf, jpg, txt, etc.) to the records of equipment in a data base. Later users can view these records of equipment and press a button to display the document.

  When the user presses the button to view the document, the application uses the folder variable to save the document to the temporary path and then asks windows via a shell command to open the file. The appeal of Delphi for windows used is the following:

  ShellExecute (GetDesktopWindow, 'open', PChar (TempFile), ",", SW_SHOWNORMAL);

  Normally this process works very well, we have had no problems so far. On a single computer (windows xp pro with Service Pack 3) belonging to a client, instead of opening the file, windows returns the system 31 error and the message ""a device attached to the system is not functioning. ". is displayed.

  * If I navigate to the location where the file is stored on the disk and try to open it, software adobe reader opens the file correctly.

  * I found some suggestions that the file extension is associated properly. PDF associated with Notepad, I changed, and the application could ask windows to open the file very well. Open the file from the location on the work of disc as well. Change the file for adobe and the problem persisted.

  * I reinstalled adobe reader software, but also a previous version of adobe and the problem persisted.

  * The application doesn't have any problem asking other files opened, only those associated with adobe reader on this same machine. The problem does not exist on other machines.

  That about sums up the problem. Any suggestion would be appreciated.

  Thank you

  Louis

  It was determined that the version of adobe reader was at fault.

• command authorization failed

  I turned on the aaa command authorization without applying the correct user privileges. I can now log on this user, but the ASA 5510 displays an error:

  ============================

  EUKFW2 # show running-config

  ^

  % ERROR: invalid input detected at ' ^' marker.

  ERROR: Failed authorization control

  ============================

  I'm unable to change the configuration of the firewall. Is there any default user through which I can connect and disable the authorization of aaa? If this is not the case, how can I solve this problem?

  Please visit this link

  http://www.ciscotaccc.com/Kaidara-Advisor/security/showcase?case=K10386224

  Please evaluate the useful messages

  Kind regards

  ~ JG

• How to run a procedure ODI of a shell command?

  Hello
  
  Is it possible to perform the procedure ODI of a shell command? How?
  
  I would like to invoke the execution of the second another batch processing procedure, we have tips.
  
  Thank you.

  You can create the scenario of the ODI procedure and call this scenario using the startscen at the command prompt,
  before that make sure that you odiparams file is updated.

• Run the automator script in a shell command

  Hello

  I would like to start an automator script in a command shell with the automator command (see automator man).

  I would like to pass an argument to the script (such as a list of files) too much with the i - settings but my syntax has failed. This is my test written in AppleScript script:

  on run
    tell application "Finder"
    set theSelection to selection
    set theFile to theSelection's item 1 as alias
    set thePath to quoted form of POSIX path of theFile
  
    log thePath
  
    set theWorkflow to quoted form of "/Users/conmeubonailleuco/Library/Mobile Documents/com~apple~Automator/Documents/Encode Audio Files.workflow"
    set theAutomatorScript to "automator " & theWorkflow & " -i (" & thePath & ")"
  
    do shell script theAutomatorScript
    end tell
  end run
  

  theAutomatorScript the value "-i «& path & space & theWorkflow» automator