Should separate you network traffic and storage?

Similar Questions

• Isolate the vMotion and storage traffic?

  We use ESXi 5.1 using two physical switches for management traffic and two physical switches for VM and storage vMotion traffic. We use a DVSwitch with VLANS separated for VMs (125), storage (126) and vMotion traffic (127). My question is really about the physical switch setting. I have installation of VLANs, 125, 126 and 127 on my main switch with each of them having a layer 3 interface. I think that only the network of the VM (vlan 125) needs a layer 3 interface. In other words, my VLAN storage and vMotion is not routable by removing the 3 layer interface.

  Does this sound correct?

  Another twist, I have a Juniper switch where all layer 3 interfaces are defined. It is connected to 4 switches in the rear of my IBM Bladecenter. Two of these switches are Cisco 1 GB switches that carry all traffic to the management through a vSwitch network. The other two switches are BNT 10 GB switches that carry traffic for Storage vMotion and VMs. Of course, it's a network connection, because it carries several VLANS.

  My only question now is should I eliminate interface layer 3 on my storage network located on one vlan separate

  Well, you need your storage system accessible on these IP addresses by the systems for the management of the other subnets or such? You already have all traffic from subnet inter between iSCSI and other networks? If this isn't the case, then there is no need to have routable iSCSI network.

  For the ESXi hosts themselves there is usually zero reason to have vmkernel iSCSI interfaces be routable since you already do management etc on another routable network (and responses of hosts would be sent there as well except if you define static routes custom).

• I have an iPhone 6 and an iPad Air both have always been updated you are prompted and are therefore currently operating on 9.2.1. It just says: update could not be completed, and that was in the 11-15. I pay for extra storage if this isn't the issue...

  I have an iPhone 6 and an iPad Air both have always been updated you are prompted and are running 9.2.1. I can't get either do an iCloud backup, he repeats to me just last backup could not be completed. The last successful backup has been in November 2015. I pay for most large storage storage account is not the problem but, the fact I pay for cela and cannot use it is very frustrating = / I really need to get my backup iPhone I have a few important pictures there. I have read other posts, but nothing useful there. Is this a problem in one of the updates at this time or some other interferente app? Or? Thank you...

  Welcome to the Apple community.

  Please check that your device is correctly connected to the wireless internet (settings > wifi) and is plugged into a power source, check also that you have enough space in iCloud for your back upward.

  You can check the space available in settings > iCloud > storage and the space needed for the next backup to the settings > iCloud > storage > Storage manage > backups > appliance > Back Up Options > next backup size (wait for the spinning until the gear icon).

  Assuming that you are eligible for iCloud upward, you should try a forced first stop, hold down the buttons side in top and home together until the unit stops, then restart by pressing the side/up button.

  Then, try to connect the device to a new location (different WiFi network)

  If your backup continues to fail, you can try to disable the backup on your mobile device (settings > iCloud > backup), reboot the device and then turn on BackUp on new.

  If this help not disable backup again, remove your existing back to the top of settings > iCloud > storage > Storage manage > backup > this device (scroll down) > delete backup, restart the device and then turn on BackUp.

  If you are unable to make a return to the top, try to connect on iCloud (settings > iCloud (scroll down) > Sign Out (you will need to enter your password at this point), restart the device and sign in iCloud to settings > iCloud.)

  The next thing to try would be to restore your network settings. (Settings > general > reset > reset network settings)

  Reset your network settings will erase your cell phones and wireless network settings, including saved networks, passwords for wifi and VPN settings, that you can use. It will affect to the Internet but will not be an impact on telephone services because these settings are automatically configured by your carrier. It may take a few moments to enter again all your network settings, but it shouldn't cause you any major problems. If you are comfortable re - enter your network settings, you can try this step earlier in the troubleshooting procedure, i.e. after the forced shutdown suggested above.

  If this does not help, try to disable some elements for the back upward in a model to try to establish if your problem is caused by specific data on your device. You can do with settings > iCloud > storage > storage management > backup > appliance > Back Up Options.

  If you are still not able to perform a backup from iCloud, you can try to restore your phone which you should do by making an iTunes backup via your computer and restore from that.

  Be able to go back to the cloud can be very useful, especially if you have access to a computer or rarely have access to one, however unless you need specifically to use iCloud to go back, you'll find a backup on iTunes much more convenient and possibly more reliable. However if you save up to iTunes be sure to encrypt the back upward if you want to keep your data on health and passwords etc.

  More on v iCloud iTunes backup

• Configure the host and the VM on two separate wireless networks

  Hello community, I was a browser for a long time, but this will be my first post.

  I would like to begin by saying that I have always found the answer I was looking for by browsing these forums and that I browsed discussions thereon and consulted the chapters regarding virtual networks in the manual workstation 7.1, but at this stage were still unable to solve my problem.

  The scenario:

  I'm a small business working in a House (upstairs) / hookah lounge (bottom). We recently had a second internet connection (WORK), Internet home of my family (HOME), to provide our customers with a free wi - fi. I would use the connection of WORK (during our hours of downtime) in a Ubuntu VM for folding and seeding of torrents. I want to put this far on a network traffic will not affect the other.

  The network:

  SE host: Windows 7 Pro 64-bit

  (Host) NIC: Intel PRO/Wireless 3945ABG (Mini PCI)

  VM: Ubuntu 10.04 on VMWare Workstation 7.0.0 build-203739

  NIC (VM): Alfa awus036h (USB)

  
  

  The current configuration:

  Network connection is made, the State of replication physical physical network is unchecked.

  The Alfa is connected to the virtual machine and is no longer present on the list of the network adapters in Windows.

  It seems that I have to manually disable the "auto eth 1" interface or the virtual machine using the internet connection in host rather than the network of your choice that the Alfa connects to in VMWorkstation. The speed of the internet with eth auto 1 is connected is quick and consistent, but using it defeats the purpose. Strangely, when I go to network connections, under the "last use" for "eth 1 auto ' it is said 'never '.

  When "eth 1 car" is disconnected, it seems that the virtual machine uses the network wireless connected to the Alfa. But the internet speed is very slow and inconsistent. On downloads, the speed varies considerably; Also, it remains at 0 kb/s for a while before going to 80 KB/s, then works his way down to 0 kb/s again.

  Possible solutions:

  1. it's a driver problem for the Alfa inside the VM environment all this time?

  2 just misunderstood how to set up this kind of virtual network?

  3 is it possible to get the desired configuration by filling the WORK and VMnet0/1/8?

  * Note: Only VMnet1 and VMnet8 appear on the Windows network connections, however isn't VMnet0 bridged one responsible for networking?

  4. upgrade to the current version of the desktop would be useful?

  5. do this problem originally because of some settings on the router?

  * Note: The AP is close enough to provide a signal strength of 85-90%

  Sorry to be so talkative, I just wanted to be as clear as possible because I'm still a beginner to learn more about virtualization.

  Thank you in advance, as always, your help is greatly appreciated.

  First of all, I must say that when I did this last response, I've been on my Mac and I thought the configuration of a host of Windows XP however outside the nomenclature of the names of the host network settings dialog box the rest stands as it is on a host Windows 7 as described below, including a picture as an attachment.

  On a Windows 7 x 64 host with two network adapters, each on a different subnet and VMware Workstation 7.1.3 installed with the editor of virtual computer network configured for VMnet0 and VMnet2 jumpered separately to one of the host of NIC and I have not changed the settings for Windows 7 host NIC-1 and have network/Internet connectivity to the host of this NETWORK adapter as shown in the picture of Google in Internet Explorer on the host computer.  In VMware Workstation 7.1.3 I have a Linux Guest configured to use VMnet2, which is filled in the settings and the Windows 7 host NIC-2 have all with the exception of VMware Bridge Protocol unchecked and have network/Internet connectivity in the guest as indicated by Google in a browser.

  From the perspective of connectivity network between the host and the guest by NIC - 2 on the host computer when all with the exception of VMware Bridge Protocol unchecked there is no connectivity between the two on this subnet because there are no protocol at stake to allow the conversation to take place.

  So theoretically and in practice what I said previously, but didn't were not expressly with a Windows 7 host in mind, nevertheless what I said is true and accurate, as evidenced by world real test/use by what I said and with the image attached herein.

  FWIW Windows 7 has been configured with the default settings and the only changes to the host's network were those made during the installation of VMware Workstation 7.1.3 so with the configuration I discussed with the attached picture, there is no reason why the host and the guest cannot be on different physical networks and each network/Internet connectivity based on the information I have provided and they be isolated from each other by being on separate physical networks.

  That said, even if they can be isolated by being on separate physical networks can still can connectivity between the 2 through VMware shared folders it it turned on and of course & slide and other services so if absolute isolation is necessary to the point where it can be, and the guest still operating system run on a Virtual Machine in the host you would need to disable the Backdoor for VMware Tools cannot provide shared folders on VMware, & glide and other services.  So if you need this isolation level let me know and I will provide additional information to complete it.

• How to monitor and lock the network traffic

  I am connected to a network that is always connected to the internet. I needed to display the bytes sent and received and also to block network traffic by not using only Internet. (Vista)

  Hello

  There are some send receive info on the status screen is in the Conncetion Local adapter.

  Look here to the right, http://www.ezlan.net/Win7/status-nic.jpg

  If you need something more complete this freeware is very good, http://www.softperfect.com/products/networx/

  Regarding the disconnection of the local network.

  If your computer is not configured for sharing, then it cannot connect to from the local network first.

  If not, right-click on the network map, and then click on turn off (do the same after to activate).

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Hub and spoke VPN network traffic between two points talked

  Hi, I have a star VPN network topology, and all traffic is remote office to the data center,

  I have a request to build a tunnel between two remote sites to access some servers between two remote sites,

  Can I just change the ACL of valuable traffic to to include say a Cabinet to Office B in rule Cabinet a Datacenter and Office B tunnel to tunnel data center.

  In doing so, I can avoide the tunnel between two offices (and B)

  See you soon

  Hello

  You can make the traffic between the two rays go through the hub or build a new tunnel between the rays.

  If the hub is an ASA you must authorize same-security-traffic intra-interface permits

  If the hub and the spokes are routers, you can also use DMVPN to dynamically create a tunnel between the spokes when necessary.

  Federico.

• total number of bytes of network traffic for a given period and given a vm guest

  Hello

  I want to see the total number of bytes of network traffic a given virtual machine generates in a give period.

  I think it's possible with a great metric but don't know how.

  Any help is welcome.

  Kristof

  This is for vrops x 6

  1. create a metric configuration

  
   
      
  
          
          
          
      
   

  2. create a new dashboard with a list of objects and graphic metric

  3 edit the object list widget, and the filter object type\Virtual Machines and save

  4. change the metrics graph and select the metric config that you created in step 1 in the metrix configuration box and save it

  5 in Widget interactions select list of objects in the menu drop-down and click on apply Interactions and save the dashboard

  When you open the control panel and select a virtual machine from the list (or search for it in the filter), it will display the average amount of data received and transmitted in Kbps in the metric table. Use the controls to date to specify when you want to see the data to and from.

  Hope this helps

• Random virtual machines after vMotion and Storage vMotion network loss

  Hi all -

  I have a couple of tickets open with VMware and our supplier of SAN, EqualLogic, on this issue.  Since the configuration of our production and DMZ clusters we noticed that the virtual machines will sometimes drop network connectivity after a successful vMotion and Storage vMotion.  Sometimes, although much less frequently, virtual machines also spontaneously lose network overnight.  What happened only a few times.  The strange thing is that the other guests on the VM host are fine - they lose any network.  Actually, I can do no more than 3 computers virtual host to another, and 2 of 3 can switch correctly, so that we lose the network.  The work around?  Simply 'disconnect' from the virtual NETWORK card 'reconnect' and the virtual machine will start the return packets.  I can also switch the VM troubled return to the host State and it will find the network.  I can it reboot and re - win network.  I can re - install the virtual card completely, and she re - win network.

  VMware has seen a lot of mistakes of SAN in our log files in order to update us our SAN firmware to the latest version.  That seems to have fixed that but we still have the issue.  Here are some of the specifications - all environments are virtually identical except for memory:

  Of PowerEdge R810

  NICs Broadcom 5709

  EqualLogic SAN running 5.0.5 F/W

  We use frames.  ESXi is fully patched.  I haven't seen a boss or not, it is only some guest operating system that loses the network, but we are a Windows environment.

  When a virtual machine loses the network, we can not:

  • Ping to it
    
  • Ping it
    
  • Ping him at the virtual machines on the same host or vSwitch
    
  • Ping outside our network
    
  • resolve DNS, etc..
    

  I followed some KBs VMware without success, including:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1003839
  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC & externalId = 1002811 (port security is not enabled)

  -All the VMware tools have been updated to the latest version correct and corresponds to the ESXi host
  -Connected to the service ESXi console, I cannot ping the VM problem by name of host or IP address, but I can ping do not affected by the issue of the OTHER virtual machines.  I can also pings the service console.
  -Connected to the troubled virtual machine itself, I cannot ping other virtual machines, I can't resolve host names, I cannot ping by IP.  The machine virtual CAN ping itself by IP, but not hostname.  I cannot ping other virtual computers on the same virtual switch or network by either IP or host name.  I can't ping the vSwitch network management.
  -All vSwitches are configured in the same way and the same.
  -Notify the switches is set to yes
  -There are a lot of available virtual ports
  -We tried the E1000 and VMXNET virtual cards with no difference.
  -All cards are configured to negotiate, but we tried to force individuals speeds as well as with no difference

  I appreciate your help.  I have problems getting anywhere on this issue with the sellers.

  wkucardinal wrote:

  Still having the issue...

  Sometimes, it might be useful to really check that all uplinks VMNIC for all VLAN does work them. Try this is to create a new portgroup on the vSwitch used by your virtual machines on the host of the first, put a test VM on the portgroup, then go into the NIC teaming policy from the new portgroup and select "Override switch command failover."

  Then down vmnic all except one in unused, then only a single VMNIC is active. Then set the portgroup VLAN to a production of VLAN and try to see if we could ping some expected from the different addresses. If it works, then move VMNIC work until unused and move up to another asset. Try again, and this for all the vmnic. If it works, then you have verified that the configuration of VLANS and other settings are correct on the physical switch in the face of this host ports.

  If several VLANs, repeat the process for all other productions VLAN. Then repeat on the other hosts.

  While that may take some time, occurs if everything is properly configured on the physical switches. When occurs a vMotion virtual machine gets a new "Port code" and is assigned to a new outgoing VMNIC. If there is an error of configuration on one or more physical ports that might seem random, but may still happen on VLAN x on y VMNIC. Given that Port ID policy you use indeed spread randomly VMs on the vmnic these problems may be difficult to diagnose. (Make a disconnection of the VM vNIC gives the virtual machine a new port-ID, which it will move to a new outgoing VMNIC, which might seem to solve the problem.)

• I was wondering if there is a limit to how much you can or should be in a folder and if so what is it?

  Title: How original is TOO many?

  I have all my MP3s in a folder that has 250 GB, there 53 600 files and folders 4 204. I was wondering if there is a limit to how much you can or should be in a folder and if so what is it?

  Hello
  
  As long as you have space and ability to manage there should be
  no real problem.
  
  --
   

  "eedog" wrote in message News: aa0d930a-d6f0-4aa7-a952-052b129d93a9...

  I have all my MP3s in a folder that has 250 GB, there 53 600 files and folders 4 204. I was wondering if there is a limit to how much you can or should be in a folder and if so what is it?

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• 1217nfw MFP how to change network name and password when you buy a new routers

  I have a 1217nfw MFP.  It was working fine without thread.  Then my router has stopped working properly.  I bought a new router and easily set up my computer, the iPad and the iPhone to work with her.  But I don't know how to change the printer set up so that he will see and connect to the new router (i.e., change the network name and the password that the printer uses to connect).  Someone knows how to do this without having to uninstall and reinstall the printer as if it was fresh out of the box?  Thanks for your help.

  Thanks a lot for your help.  The choice to click on my laptop were not quite the same as stated in the article, but the article got to the right spot and I was able to figure out the rest.  So now my laptop is wireless printing.  MacBook Air my wife still does not work, but I'll play with it after the holiday weekend.  Do you know of an article that allows to change the name of the router and the password when it is a Mac?  Whatever it is, thank you very much for your quick response and help.

• I bought the full version from the Swedish retailer Dustin but got a trial version has expired. Dustin claims that they sell not trial versions and that I should contact you. When strting Lightroom, I get a Windows window pop saying that a

  I bought the full version from the Swedish retailer Dustin but got a trial version has expired. Dustin claims that they sell not trial versions and that I should contact you. When strting Lightroom, I get a Windows pop in window saying that a procedure start address __crtCreateSymbolicLinkW is not I have the DLL file C:\WINDOWS\SYSTEM32\MSVCP110.dll

  Hi leifp,

  Refer to this link and download Microsoft Visual C++ 4 updated 2012 from this link and install it:

  Download Visual C++ Redistributable for Visual Studio 2012 updated 4 of the official Microsoft Download Center

  Kind regards

  Claes

• I transferred my Lightroom 5.7.1 my cell phone to my PC. I put in the serial number, you press "next" and another box came up saying that the updated code was for and upgraded version and I should put in the old version the serial number - this I can't f

  I transferred my Lightroom 5.7.1 my cell phone to my PC. I put in the serial number, you press "next" and another box came up saying that the updated code was for and upgraded version and I should put in the old version the serial number - this that I can't find

  you will need to this previous version number and serial number.

  If you purchased the previous version of adobe or registered with adobe, check your account: ID Adobe

  in otherwise, find the serial number of your product Adobe quickly

• I use windows 10 on pc. Creative cloud must update. He gets 2% and keep saying "error code: 81 please close the other setup programs" when you look at the Task Manager, no setup program is running. What should I do? Photoshop and Lightroom will not wor

  I use windows 10 on pc. Creative cloud must update. He arrived at 2% and stops, saying: "error code: 81 please close the other setup programs" when you look at the Task Manager, no setup program is running. What should I do? Photoshop and Lightroom do not work for me right now.

  Close applications or contradictory processes

  Solve the problems of downloading and installation of Adobe Creative Cloud

  Mylenium

• Grouping of NETWORK adapters and NLB on ESXi 3.5

  I want to get ESXi to load balance the traffic to my NFS storage, but have had no success. My test set up is the following:

  • Two blades each with two physical network adapters dedicated to the ESXi for NFS kernel ports

  • Two switches

  • A NETWORK adapter on each blade is connected to each switch - it isn't an Etherchannel or trunking configured

  • Two NFS devices on a different IP address

  • Eight virtual machines on each blade, four to connect to a data store on each device of NFS

  • ESXi NIC teaming across two network cards with the option "route based on the virtual origin of switch port code.

  My understanding is that each virtual computer must use one of the network cards, but about half must use a physical NETWORK card and half the other. Instead, all the traffic of all eight VMs released a physical NIC if I disable the physical NIC, it moves the second NETWORK card without problem. Then they both work, but he never uses both at the same time. This behavior is consistent across the two blades.

  Is throughbut limited to ~ 110 MB per blade and the storage system can easily exceed this.

  I've attached a screenshot of a virtual switch in place.

  TIA,

  Will be

  Virtual machines are access NFS data warehouses directly? If Yes, then yes it should work that way - however if you are using the NFS data store to host the VM files, including virtual disks and then traffic will turn off the vmkernel port and if have vmkernel unique port then what you are experiencing is expected - the vmkernel selects the outgoing NIC based on the virtual port id so if you have a single port vmkernel will suffice a single port as well as a NETWORK identifier unique will be used.

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• Separate physical network for VMotion?

  In my design to an ESXi 3.5 on HP Blades I've defined for the management network 2 natachasery and 2 natachasery for VMotion. These go to separate switches blade Cisco 3120. Now I stipulated a stack of external switch to reach the switches for VMotion. The management of the network switches then go to another pile of management. Client E wants to reduce costs by sharing the external battery for traffic management and Vmotion and segregation through VLANs and making the VMotion VLAN non routable. Will there be falls for this?

  Keep in mind, it is a safe place. IW has also always said that VLANing should not serve as a separation of security because of the possibility of VLAN hopping. What are the risks here? Keep in mind that it is a sensitive network of defence-biased, so I try to separate the networks as much as possible.

  Your ideas are welcome

  If you have material (switches) in order to separate the network infrastructure then I do for reasons of pure performance.

  A physical firewall allows us to block all to enter our management and VMotion networks.

  They are both VLAN behind the firewall, but we can still allow a privileged access to the workstations of the administrator or a management server to reduce the footprint.  This method allows to manage the network with special exceptions.

  Sound risk pure vs cost.  If you think you have a good chance of someone Vlan jumping on your internal network, and then using physical security is the best bet.  If it's a low risk, then just segment it out with VLAN and use access lists and change ports to reduce the risk of vlan hopping.

  Hope this helps you decide.