Site to Site NAT number, need a static mappings

Similar Questions

• VPN site to Site - NAT network internal

  Hi all

  I have a site to site VPN setup (both sites have Cisco ASA) where my internal network is 192.168.1.0/24 and internal, the other site of the network happens to have the exact same internal network. Is it possible that I can NAT my internal address to 172.18.1.0/24 and I get the job? It should then allow both sites to communicate successfully. Thank you.

  Hello

  You'll have to NAT to both ends of the VPN L2L connection. This is because even if you the other end to another network NAT it will mean that this site would have to connect to a destination address that is apparently in its own network and connections would fail.

  The format of configuration depends on your level of ASAs software

  8.2 software (and below)

  Comment by L2LVPN-POLICYNAT-access list policy NAT for VPN L2L

  permit access-list L2LVPN-POLICYNAT

  static (inside, outside) access-list L2LVPN-POLICYNAT

  Software 8.3 (and above)

  the object of the LAN network

  subnet

  network of the LAN - NAT object

  subnet

  network of the REMOTE object

  subnet

  NAT static LAN LAN destination - NAT source (indoor, outdoor) static REMOTE

  Note to use the correct networks in the statements above. The destination in the configuration network is naturally the NAT network uses the other site.

  In the same say, you can you make sure your L2L Crypto ACL VPN connections using the local NAT network as the source and the remote NAT network as the destination.

  Hope this helps

  -Jouni

• interesting question of the vpn site to site NAT/PAT traffic config

  I have an ASA 8.4.2 running code and am just checking the Site to site configs before migration of tunnel. more precisely if the NAT/PAT and ACL is correct. Phase 1 is already defined and work, as well as cryptographic maps and tunnel groups.

  When you set the traffic interesting in the ACL are you using NAT or the real IP? The order of the ACL is correct?

  First of all:

  The vedor network is a 192.168.1.10 and must be coordinated to 10.1.0.2

  name 5.6.7.8 VendorName object-group network VendorName-R network-object host 192.168.1.10 object-group network VendorName-NAT-R network-object host 10.1.0.2 object-group network VendorName-L network-object host 10.1.1.3 access-list VendorName-crypto extended permit ip object-group VendorName-L object-group VendorName-NAT-R nat (inside,outside) 1 source static VendorName-L VendorName-NAT-R destination static VendorName-R VendorName-R

  Second:

  Sellers network is 192.168.1.0 to 192.168.2.0, these must be PATed 10.1.0.2 and 10.1.0.3

  192.168.1.20 and 168.1.21 must be staticly using a NAT 10.1.0.4 and 10.1.0.5

  Name the SupplierName 5.6.7.8

  object-group network VendorName-R-1

  network-object subnet 192.168.1.0 255.255.255.0

  object-group network VendorName-R-2

  network-object subnet 192.168.2.0 255.255.255.0

  object-group network VendorName-R-3

  network-object host 192.168.1.20

  object-group network VendorName-R-4

  network-object host 192.168.1.21

  object-group network VendorName-NAT-R-1

  network-object host 10.1.0.2

  object-group network VendorName-NAT-R-2

  network-object host 10.1.0.3

  object-group network VendorName-NAT-R-3

  network-object host 10.1.0.4

  object-group network VendorName-NAT-R-4

  network-object host 10.1.0.5

  object-group network VendorName-R

  network-object VendorName-NAT-R-1

  network-object VendorName-NAT-R-2

  network-object VendorName-NAT-R-3

  network-object VendorName-NAT-R-4

  object-group network VendorName-L

  network-object host 10.1.1.3

  the object-Network 10.1.1.6 host

  VendorName-crypto allowed extended ip access-list object-VendorName-L Group VendorName-R

  NAT (inside, outside) 1 dynamic source VendorName-l VendorName-NAT-R-1 static destination VendorName-R-1 VendorName-R-1

  NAT (inside, outside) 1 dynamic source VendorName-l VendorName-NAT-R-2 static destination VendorName-R-2 VendorName-R-2

  NAT (inside, outside) 1 static source VendorName-l VendorName-NAT-R-3 of destination VendorName-R-3 static VendorName-R-3

  NAT (inside, outside) 1 static source VendorName-l VendorName-NAT-R-4 static destination VendorName-R-4 VendorName-R-4

  Your valuable traffic acl MUST be the IP NAT address.

• Update soundcards site says I need to install the ActiveX control, but there is no bar at the top click or any other option to download.

  Update soundcards site says I need to install the ActiveX control, but there is no bar at the top click or any other option to download.  How can I download this control so I can access the Windows Update Web site?

  See if that helps-

  How to reset the Windows Update settings?
  http://support.Microsoft.com/kb/971058

• cannot reactivate the CS2 after the hard disk crash - site says I need to talk with adobe (activation can be done online) but the customer support page loop all around - help/activate also not going anywhere - it's a pc - thank you!

  cannot reactivate the CS2 after the hard disk crash - site says I need to talk with adobe (activation can be done online) but the customer support page loop all around - help/activate (since the opening page of CS2) also not going anywhere... it is a pc - thank you!

  message says 'unavailable activation server this time... error code 24:24.

  Error: "Activation Server is not available. CS2, Acrobat 7, pass a hearing 3

• Our firewall blocks a lot of sites and I need to know the ip address in photoshop and adobe illustrator activation

  Hello

  Our firewall blocks a lot of sites and I need to know the IP address to activate the photoshop and illustrator. (Inicio sesion Errores, activacion o conexion |) CS5.5 y posterior, Acrobat DC)

  Thank you very much

  Combinations of Adobe host Ports for installation, activation and updates.

  • ccmdl.Adobe.com:80
  • swupmf.Adobe.com:80
  • swupdl.Adobe.com:80
  • https://na1mbls.licenses.Adobe.com
  • https://IMS-NA1.adobelogin.com
  • https://adobeid-NA1.Services.Adobe.com
  • https://na1r.Services.Adobe.com
  • http://activate.Adobe.com
  • https://activate.Adobe.com
  • http://Adobe.activate.com
  • https://Adobe.activate.com
  • ccmdls.Adobe.com:443
  • IMS - na1.adobelogin.com:443
  • na1r.Services.Adobe.com:443
  • prod-rel-ffc - ccm.oobesaas.adobe.com:443
  • LM.licenses.adobe.com:443
  • www-DU1.adobe.com

• I downloaded flash builder 4.7 and site serial number of licence in form but after installation it says "S

  I downloaded flash builder 4.7 and site serial number of licence in form but after installation it says "login required". According to the FAQ record should not be held for volume licenses. I am not able to connect after clicking on "connect now". Help, please

  Contact adobe support, http://www.adobe.com/support/chat/ivrchat.html

• ICloud Keychain how can I change the phone number needed to verify the code text for me? The number it was sent is an old phone number of my friends that I do not have access to the.

  ICloud Keychain how can I change the phone number needed to verify the code text for me? The number it was sent is an old phone number of my friends that I do not have access to the.

  Try this from another thread I saw.

  On iOS, go to settings > iCloud > keychain and tap button to disable iCloud keychain. (you will be asked to delete or keep the passwords on device) I chose to delete...

  Then turn it back on, and pop - up chose reset iCloud trousseau, on a chosen pop-up confirmation reset

  In the new window pop up use iPhone password like iCloud cryptogram? has chosen the use code

  Enter your secret code (4 digits) then choose country and your new phone number

  Although, to "Restore the iCloud Keychain," I took to erase the data and essentially set up a new keychain.  Not the case.  Strangely, after essentially bypassing the security system, setting a new password and verification number, I see my cards, passwords and other data have been restored.  Maybe it's all the iCloud account and this master password.  Or maybe it's a bug.  With Apple, we'll never know.

  Also have a look here: get help using iCloud Keychain - Apple Support

• ASA Configuration of VPN Site to Site - NAT issues

  Greetings,

  I am responsible to configure a VPN connection from site to site to a business partner in which I want to firstly NAT to my internal IP to a public IP address and then send it through the tunnel, and vice versa when they try to access my servers I want to get to them through the external IP address.  Here's what I think I do, but I was wondering what were the thoughts of the community.

  All of the IP addresses represented below are fictitious.

  Internal servers Public IP address         

  10.50.220.150 208.180.170.182

  10.50.220.151 208.180.170.183

  10.50.220.152 208.180.170.184

  Local peer IP: 208.180.254.29

  Distance from peer IP: 207.190.218.31

  Local network: 208.180.170.0/24

  Remote network: 207.190.239.0/24

  From my understanding, NAT occur before being sent to a tunnel, or to the internet, etc, so the configuration that I think I need is the following:

  NAT (inside) 0 access-list sheep

  NAT (inside) 2 10.50.220.150

  NAT (inside) 3 10.50.220.151

  NAT (inside) 4 10.50.220.152

  Global 2 208.180.170.182 (outside)

  overall 3 208.180.170.183 (outside)

  Global 4 208.180.170.184 (outside)

  IP 208.180.170.0 allow Access-list extended sheep 255.255.255.0 207.190.239.0 255.255.255.0 (do I still need this since coordinated to a public IP address still?)

  access-list s2s client scope ip 208.180.170.0 allow 255.255.255.0 207.190.239.0 255.255.255.0

  Route outside 207.190.239.0 255.255.255.0 207.190.218.31

  card crypto off peers set 1 207.190.218.31

  Crypto card outside 1 correspondence address s2s-customer

  [... rest of the configuration failed..]

  That look / her right? If this isn't the case, please advise.

  Thank you.

  Yes.

  PAT (nat/global) will take care of outgoing and static traffic will take care of incoming traffic.

  You can create political NAT as well to handle this traffic.

  Federico.

• Access to the Microsoft Update Web site [error number: 0x8024400A]

  When I try to update by using the Update Web site I get the message [error number: 0x8024400A].  I need to upgrade to SP3, but I can't access the Web site to do this.  Any help would be appreciated.

  Try to download the SP directly from here.

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=24

  I hope this helps.

• IPSEC VPN from Site to Site - NAT problem with address management

  Hi all

  I have two Cisco ASA 5505 performing of IPSEC Site to Site VPN. All traffic inside each firewall through the VPN tunnel and I have full connectivity. From site A, I can connect to the inside address of the ASA at the site B and launch of the ASDM or SSH, etc.

  The problem I have is when I'm logged on the ASA site B management traffic is given the external address. I created this as interesting traffic to get it to go through the VPN but I need to use the inside address of ASA B. The following is possible:

  • If I can make the ASA Site B to use inside interface as its address management (I already have management access to the inside Interface)
  • I have NAT can address external interfaces to Site B before moving through the VPN tunnel management traffic so that it appears to come from Site B inside the address
  • I can NAT VPN traffic as it appears in the Site A for management traffic to Site B on the right address.

  The problem is that my PRACTICE Please also come from this address and I need the application before being on an internal address to even if my CA.

  Thanks for any help.

  Ian

  Thanks, I understand what you are trying to achieve now.

  However, I think that I don't have good news for you. Unfortunately PEIE request can be initiated of the SAA within the interface, as there is no option to start the query from the inside interface. With other features of management such as AAA, logging, you have an option to specify what ASA desired originally to demand from interface, but CEP doesn't have this option.

  Here's how you can configure under the trustpoint crypto, but unfortunately by specifying the interface doesn't not part of option:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/command/reference/C5.html#wp2262210

• Migrating php site at apex, need help

  Hi all

  I am quite new to oracle apex so please forgive me if this could be a noob question.

  Request Express 4.2.2.00.11

  I have these codes for example (in php and html)

  partial php code:

  $getSelectedHospital ="SELECT
    F.FACILITY_NAME,
    F.FACILITY_CODE,
    FD.FACILITY_STATUS,
    F.FACILITY_ABC,
    F.FACILITY_ACCRE_CODE,
    F.FACILITY_ACC_START,
    F.FACILITY_ACC_END,
    F.FACILITY_TYPE,
    F.FACILITY_ADDRESS,
    F.FACILITY_CONTACT,
    F.FACILITY_EMAIL,
    F.FACILITY_HEAD
    FROM FACILITY_DETAIL FD
    INNER JOIN FACILITY F ON FD.FACILITY_ID=F.FACILITY_ID
    WHERE FD.FACILITY_DETAIL_ID=:facilityID";
  
  
  $queryGetHospitalGenInfo = $getSelectedHospital;
  $hospitalGenInfoResult = oci_parse($conn, $queryGetHospitalGenInfo);
  oci_bind_by_name($hospitalGenInfoResult, ":facilityID", $hospitalDetailID);
  oci_define_by_name($hospitalGenInfoResult, 'FACILITY_NAME', $facility_name);
  oci_define_by_name($hospitalGenInfoResult, 'FACILITY_STATUS', $facility_status);
  oci_define_by_name($hospitalGenInfoResult, 'FACILITY_CODE', $facility_code);
  oci_define_by_name($hospitalGenInfoResult, 'FACILITY_ABC', $facility_abc);
  oci_define_by_name($hospitalGenInfoResult, 'FACILITY_ACCRE_CODE', $facility_accre_code);
  oci_define_by_name($hospitalGenInfoResult, 'FACILITY_ACC_START', $facility_acc_start);
  oci_define_by_name($hospitalGenInfoResult, 'FACILITY_ACC_END', $facility_acc_end);
  oci_define_by_name($hospitalGenInfoResult, 'FACILITY_TYPE', $facility_type);
  oci_define_by_name($hospitalGenInfoResult, 'FACILITY_ADDRESS', $facility_address);
  oci_define_by_name($hospitalGenInfoResult, 'FACILITY_CONTACT', $facility_contact);
  oci_define_by_name($hospitalGenInfoResult, 'FACILITY_EMAIL', $facility_email);
  oci_define_by_name($hospitalGenInfoResult, 'FACILITY_HEAD', $facility_head);
  
  oci_execute($hospitalGenInfoResult);
  oci_fetch($hospitalGenInfoResult);
  
  
  

  partial html code:

  <td class="heading_td_top"><?php echo $facility_name;?></td>
  
  

  It is quite easy to view the results of my query in my html code since I can just echo variables of my lines of oci_define_by_name.

  How do I in the oracle apex? you have no need to spoon feed me, you can just point me to a tutorial or some keywords. Thank you!

  PS

  in my two months of game w / apex oracle, I really like it. I miss just the possibility to have codes php at my disposal when I ask things.

  Post edited by: m.davide, typo

  BillyVerreynne wrote:

  Dynamic PL/SQL region.

  Use the following pattern of PL/SQL code as the source for the region:

  HTP. PRN (')

  ' );

  for loop c in (select...)

  HTP. PRN (')'|| c.Col1 |');

  end loop;

  HTP. PRN (»)

  Develop/substitute HTML table set in the shape as needed.

  I would use regions standard report with custom report templates to keep things as declarative as possible. This approach has much better separation of concerns as a dynamic region of PL/SQL. SQL, HTML, and CSS are all treaties in layers separate and are so much easier to understand, debug and modify as PL/SQL with sliders. FOR loops; loads of very tedious HTP. P, string concatenations, '<'s and="" '="">of.

  With a lateral thinking and creative models of the line, expressions and logical query usage, standard APEX reports are able to produce complex structures and layouts:

  • Model number of custom report
  • Custom template: table in a table

  m.Davide wrote:

  90% of my php site has been implemented in my new site of apex. My only complaint are the profiles (which resembles typical profiles, as a profile facebook but for hospitals). I want to just recreate the look of my php site since my boss wants a look almost identical.

  What I intend to do, is create an HTML region where I have my own layout code. My problem is how to fill my custom html table.

  Create the layout using custom of APEX (page/region/State) templates. As Billy says forget the procedural approach of PHP and use the declarative features that provides the APEX.

• site says I need to enable cookies, but I activated the cookies!

  I tried to visit several Web sites today, but when I'm here it says I have disabled cookies and I need to allow them to visit the site. When I check my cookie settings, he says they are THERE! Why am I all of a sudden having this problem? I have not changed my settings! Help, please. I need these sites to finish my work!

  Hi Lisa, you could first check your settings on the Options page, Privacy panel, as described in this article:

  Web sites say cookies are blocked - pledge

  If that extracts, perhaps one of your modules causing the problem. Could test you mode without failure of Firefox? In Safe Mode, Firefox temporarily disables extensions, hardware acceleration, and a few other advanced features to help you determine if they are at the origin of the problem.

  Does not work if Firefox: Hold down the SHIFT key when you start Firefox.

  If Firefox is running: You can restart Firefox in Mode safe mode using either:

  • button "3-bar" menu > "?" button > restart with disabled modules
  • Help menu > restart with disabled modules

  and OK reboot.

  Two scenarios: A small dialog box should appear. Click on 'Start mode safe' (not update).

  Any improvement? (More info: questions to troubleshoot Firefox in Safe Mode)

• Firefox 5 is not compatible with the FAFSA site and I need to access NOW

  I am running Windows XP. I just upgraded to Firefox 5, and I need to go to the FAFSA website. Immediately. I find that, according to this site, there is an inconsistency with what anyone greater than 3.5 or 3.6. I can't find an earlier version of Mozilla to install instead of the new. THIS IS PRODUCED WHENEVER MOZILLA "IMPROVES".
  I tried to install Internet Explorer instead because it's compatible. Surprise, surprise, Mozilla doesn't let me install it. Help me ASAP please.

  Windows comes with Internet Explorer, integrated and practically installable. You should have another look.

  If all else fails, you should be able to download Google Chrome or Opera. You might be able to use them directly or you should be able to install Internet Explorer with Opera or Chrome - check the compatible version numbers.

  I sent one FAFSA email telling them that they are updated at least three behind.

• Site to site VPN, I need all internet traffic to exit the site.

  I have 2 sites connected via a pair of SRX5308

  A = 192.168.1.0/24

  IP WAN = 1.1.1.1

  B = 192.168.2.0/24

  IP WAN = 2.2.2.2

  Now what I need to do, is to have all traffic from B to go to the site one even traffic destined to the internet. That is, I need internet traffic out of our network with the IP 1.1.1.1, even if it is from the network B.

  On my I have set up a route 1.1.1.1 of the ISP, then a value by default 0/0 to 192.168.1.1 it ASA knows how to get to the peer VPN is a more specific route, but sends everything above the tunnel, at the remote end which then hairpin of ASA routes internet outside its own WAN port traffic.

  I can understand though not how to so the same thing on the pair of SRX5308 they either don't raise the tunnel or internet route to the local site address B.

  Anyone have any ideas?

  I need to do this because we are logging and monitoring of internet traffic to A site via tapping from upstream to various IDS solutions and will not (cannot) reproduce this to all our remote sites.

  Thank you

  Dave.

  After some more thought and testing I came up with a workable solution to my own problem. I'll share it here in case it can help others.

  (1) use the wizard at both ends to implement a normal VPN that connects the two segments of network 192.168.1.0 and 192.168.2.0

  (2) go to site VPN - VPN policy remote router192.168.2.1 and click Edit

  (a) disable Netbios

  (b) select "None" from the drop-down list the remote IP address.

  (c) to apply the change

  3) go to the VPN-> VPN policy on the head end site (192.168.1.1) and click Edit

  (a) disable Netbios

  (b) select "None" from the drop-down list the local IP address

  (c) to apply the change

  Now all the traffic wil go down the VPN tunnel and exit to the internet on the site of head end. Hope this helps others with the same question.