ASA Configuration of VPN Site to Site - NAT issues

Greetings,

I am responsible to configure a VPN connection from site to site to a business partner in which I want to firstly NAT to my internal IP to a public IP address and then send it through the tunnel, and vice versa when they try to access my servers I want to get to them through the external IP address. Here's what I think I do, but I was wondering what were the thoughts of the community.

All of the IP addresses represented below are fictitious.

Internal servers Public IP address

10.50.220.150 208.180.170.182

10.50.220.151 208.180.170.183

10.50.220.152 208.180.170.184

Local peer IP: 208.180.254.29

Distance from peer IP: 207.190.218.31

Local network: 208.180.170.0/24

Remote network: 207.190.239.0/24

From my understanding, NAT occur before being sent to a tunnel, or to the internet, etc, so the configuration that I think I need is the following:

NAT (inside) 0 access-list sheep

NAT (inside) 2 10.50.220.150

NAT (inside) 3 10.50.220.151

NAT (inside) 4 10.50.220.152

Global 2 208.180.170.182 (outside)

overall 3 208.180.170.183 (outside)

Global 4 208.180.170.184 (outside)

IP 208.180.170.0 allow Access-list extended sheep 255.255.255.0 207.190.239.0 255.255.255.0 (do I still need this since coordinated to a public IP address still?)

access-list s2s client scope ip 208.180.170.0 allow 255.255.255.0 207.190.239.0 255.255.255.0

Route outside 207.190.239.0 255.255.255.0 207.190.218.31

card crypto off peers set 1 207.190.218.31

Crypto card outside 1 correspondence address s2s-customer

[... rest of the configuration failed..]

That look / her right? If this isn't the case, please advise.

Thank you.

Yes.

PAT (nat/global) will take care of outgoing and static traffic will take care of incoming traffic.

You can create political NAT as well to handle this traffic.

Federico.

Tags: Cisco Security

Similar Questions

cannot ping remote ip on ASA no firewall (VPN site to site on SAA) configired no proxy, icmp not inspect, no chance

some help me

(Q) ping remote ip unable on ASA is not Firewall not on pc (VPN site to site on SAA) configired no proxy, icmp not inspect, no chance

Note - I can ping PC but not the same subnet ip on ASA2 L3

PC---> > ASA1 - ASA2<>

Hi Matt,

Let me answer your question in two points:
- You cannot ping an ASA on another interface other than the one where you are connected to the ASA of.
For example, ASA1 and ASA2 are connected through their interfaces 'outside '. ASA1 (or any other device on the external interface) can not ping/access ASA2 on his (ASA2) within the interface. The only time wherever this can be substituted is a tunnel VPN with the command "access management" configured for other interface, for example management-access inside
- Traffic ASA1 ping to a remote client behind ASA2 won't over the VPN tunnel and as such is not encrypted. That's because ASA1 will forward traffic based on its routing table that probably this way through its 'outside' interface Except that traffic is allowed with the ASA2 (using the ACL), it will fail.
We can do on the routers of sourcing our ping to another interface, but it will not work on the SAA.

Can the NAT of ASA configuration for vpn local pool

We have a group of tunnel remote ipsec, clients address pool use 172.18.33.0/24 which setup from command "ip local pool. The remote cliens must use full ipsec tunnel.

Because of IP overlap or route number, we would like to NAT this local basin of 172.18.33.0 to 192.168.3.0 subnet when vpn users access certain servers or subnet via external interface of the ASA. I have nat mapping address command from an interface to another interface of Armi. The pool local vpn is not behind any physical interface of the ASA. My question is can ASA policy NAT configuration for vpn local pool. If so, how to set up this NAT.

Thank you

Haiying

Elijah,

NAT_VPNClients ip 172.18.33.0 access list allow 255.255.255.0 10.1.1.0 255.255.255.0

public static 192.168.33.0 (external, outside) - NAT_VPNClients access list

The above configuration will be NAT 172.18.33.0/24 to 192.168.33.0/24 when you go to 10.1.1.0/24 (assuming that 10.1.1.0/24 is your subnet of servers).

To allow the ASA to redirect rewritten traffic the same interface in which he receive, you must also order:

permit same-security-traffic intra-interface

Federico.

ASA 5505. VPN Site-to-Site does not connect!

Hello!
Already more than a week there, as we had a new channel of communication of MGTSa (Ontario terminal Sercomm RV6688BCM, who barely made in the 'bridge' - had to do the provider in order to receive our white Cisco Ip address), and now I train as well more that one week to raise between our IKEv1 IPsec Site-to-Site VPN tunnel closes offices.
Configurable and use the wizard in ASDM and handles in the CLI, the result of a year, the connection does not rise.
Cisco version 9.2 (2), the image of the Cisco asa922 - k8.bin, Security Plus license version, version 7.2 AMPS (2).
What I'll never know...
Debugging and complete configuration enclose below.
Help, which can follow any responses, please! I was completely exhausted!

Config:

Output of the command: "sh run".

: Saved
:
: Serial: XXXXXXXXXXXX
: Material: ASA5505, 512 MB RAM, 500 MHz Geode Processor
:
ASA Version 9.2 (2)
!
hostname door-71
activate the encrypted password of F6OJ0GOws7WHxeql
names of
IP local pool vpnpool 10.1.72.100 - 10.1.72.120 mask 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 10.1.72.254 255.255.255.0
!
interface Vlan2
nameif outside_mgts
security-level 0
62.112.100.R1 255.255.255.252 IP address
!
passive FTP mode
clock timezone 3 MSK/MSD
clock to DST MSK/MDD recurring last Sun Mar 02:00 last Sun Oct 03:00
DNS lookup field inside
DNS server-group MGTS
Server name 195.34.31.50
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
network of the NET72 object
10.1.72.0 subnet 255.255.255.0
network object obj - 0.0.0.0
host 0.0.0.0
network of the Nafanya object
Home 10.1.72.5
network object obj - 10.1.72.0
10.1.72.0 subnet 255.255.255.0
network of the NET61 object
10.1.61.0 subnet 255.255.255.0
network of the NETWORK_OBJ_10.1.72.96_27 object
subnet 10.1.72.96 255.255.255.224
network of the NETT72 object
10.1.72.0 subnet 255.255.255.0
network of the NET30 object
10.1.30.0 subnet 255.255.255.0
network of the NETWORK_OBJ_10.1.72.0_24 object
10.1.72.0 subnet 255.255.255.0
object-group service OG INET
the purpose of the echo icmp message service
response to echo icmp service object
service-object icmp traceroute
service-object unreachable icmp
service-purpose tcp - udp destination eq echo
the DM_INLINE_NETWORK_1 object-group network
network-object NET30
network-object, object NET72
DM_INLINE_TCP_1 tcp service object-group
port-object eq www
EQ object of the https port
inside_access_in extended access list permit ip object NET72 object-group DM_INLINE_NETWORK_1
access extensive list ip 10.1.72.0 inside_access_in allow 255.255.255.0 any
inside_access_in extended access list permit ip object Nafanya any idle state
inside_access_in list extended access allowed object-group OG INET an entire
inside_access_in of access allowed any ip an extended list
inside_access_in list extended access deny ip any alerts on any newspaper
outside_mgts_access_in list extended access allowed object-group OG INET an entire
outside_mgts_access_in list extended access permit tcp any any DM_INLINE_TCP_1 object-group
outside_mgts_access_in list extended access deny ip any alerts on any newspaper
access extensive list ip 10.1.72.0 outside_mgts_cryptomap allow 255.255.255.0 object NET61
VPN-ST_splitTunnelAcl permit 10.1.72.0 access list standard 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
outside_mgts MTU 1500
IP check path reverse interface outside_mgts
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside outside_mgts) static source NET72 NET72 NETWORK_OBJ_10.1.72.96_27 NETWORK_OBJ_10.1.72.96_27 non-proxy-arp-search of route static destination
NAT (inside outside_mgts) static source NETWORK_OBJ_10.1.72.0_24 NETWORK_OBJ_10.1.72.0_24 NET61 NET61 non-proxy-arp-search of route static destination
!
network obj_any object
NAT (inside outside_mgts) dynamic obj - 0.0.0.0
network of the NET72 object
NAT (inside outside_mgts) interface dynamic dns
inside_access_in access to the interface inside group
Access-group outside_mgts_access_in in the outside_mgts interface
Route 0.0.0.0 outside_mgts 0.0.0.0 62.112.100.R 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
without activating the user identity
identity of the user by default-domain LOCAL
AAA authentication http LOCAL console
the ssh LOCAL console AAA authentication
Enable http server
http 10.1.72.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
card crypto outside_mgts_map 1 match address outside_mgts_cryptomap
card crypto outside_mgts_map 1 set pfs Group1
peer set card crypto outside_mgts_map 1 91.188.180.42
card crypto outside_mgts_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_mgts_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
card crypto outside_mgts_map interface outside_mgts
inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
inside crypto map inside_map interface
Crypto ca trustpoint ASDM_TrustPoint0
registration auto
E-mail [email protected] / * /
name of the object CN = door-71
Serial number
IP address 62.112.100.42
Proxy-loc-transmitter
Configure CRL
Crypto ca trustpoint ASDM_TrustPoint1
registration auto
ASDM_TrustPoint1 key pair
Configure CRL
trustpool crypto ca policy
string encryption ca ASDM_TrustPoint0 certificates
certificate eff26954
30820395 3082027d a0030201 020204ef f2695430 0d06092a 864886f7 0d 010105
019
6460ae26 ec5f301d 0603551d 0e041604 14c9a3f2 d70e6789 38fa4b01 465d 1964
60ae26ec 5f300d06 092 has 8648 01050500 03820101 00448753 7baa5c77 86f70d01
62857b 65 d05dc91e 3edfabc6 7b3771af bbedee14 673ec67d 3d0c2de4 b7a7ac05
5f203a8c 98ab52cf 076401e5 1a2c6cb9 3f7afcba 52c617a5 644ece10 d6e1fd7d
28b57d8c aaf49023 2037527e 9fcfa218 9883191f 60b221bf a561f2be d6882091
0222b7a3 3880d6ac 49328d1f 2e085b15 6d1c1141 5f850e5c b6cb3e67 0e373591
94a 82781 44493217 and 38097952 d 003 5552 5c445f1f 92f04039 a23fba20 b9d51b13
f511f311 d1feb2bb 6d056a15 7e63cc1b 1f134677 8124c 024 3af56b97 51af8253
486844bc b1954abe 8acd7108 5e4212df db835d76 98ffdb2b 8c8ab915 193b 8167
0db3dd54 c8346b96 c4f4eff7 1e7cd576 a8b1f86e 3b868a6e 89
quit smoking
string encryption ca ASDM_TrustPoint1 certificates
certificate a39a2b54
3082025f 30820377 a0030201 020204 has 3 9a2b5430 0d06092a 864886f7 0d 010105
0500304 06035504 03130767 36313137 30120603 55040513 6174652d 3110300e b

c084dcd9 d250e194 abcb3eb8 1da93bd0 fb0dba1a b1c35b43 d547a841 5d4ee1a4
14bdb207 7dd790a4 0cd 70471 5f3a896a 07bd56dc ea01b3dd 254cde88 e1490e97
f3e54c05 551adde0 66aa3782 c85880c2 b162ec29 4e49346a df71062d 6d6d8f49
62b9de93 ba07b4f7 a50e77e1 8f54b32b 6627cb27 e982b36f a 362973, 0 88de3272
9bd6d4d2 8ca1e11f 214f20a9 78bdea95 78fdc45c d6d45674 6acb9bcb d0bd930e
638eedfe cd559ab1 e1205c48 3ee9616f e631db55 e82b623c 434ffdc1 11020301
0001 has 363 3061300f 0603551d 130101ff 0101ff30 04053003 0e060355 1d0f0101
ff040403 1f060355 02018630 230418 30168014 0cea70bf 0d0e0c4b eb34a0b1 1 d
8242 has 549 0603 551d0e04 1604140c ea70bf0d 0e0c4beb 34a0b182 301D 5183ccf9
42a 54951 010105 05000382 0101004e 7bfe054a 0d 864886f7 0d06092a 83ccf930
d434a27c 1d3dce15 529bdc5f 70a2dff1 98975de9 2a97333b 96077966 05a8e9ef
bf320cbd ecec3819 ade20a86 9aeb5bde bd129c7b 29341e4b edf91473 f2bf235d
9aaeae21 a629ccc6 3c79200b b9a89b08 bf38afb6 ea56b957 4430f692 a 4745, 411
34d71fad 588e4e18 2b2d97af b2aae6b9 b6a22350 d031615b 49ea9b9f 2fdd82e6
ebd4dccd df93c17e deceb796 f268abf1 881409b 5 89183841 f484f0e7 bd5f7b69
ebf7481c faf69d3e 9d24df6e 9c2b0791 785019f7 a0d20e95 2ef35799 66ffc819
4a77cdf2 c6fb4380 fe94c13c d4261655 7bf3d6ba 6289dc8b f9aad4e1 bd918fb7
32916fe1 477666ab c2a3d591 a84dd435 51711f6e 93e2bd84 89884c
quit smoking
crypto isakmp identity address
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 activate outside_mgts port 443 customer service
Crypto ikev2 access remote trustpoint ASDM_TrustPoint0
Crypto ikev1 allow inside
Crypto ikev1 enable outside_mgts
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
without ssh stricthostkeycheck
SSH 10.1.72.0 255.255.255.0 inside
SSH timeout 60
SSH group dh-Group1-sha1 key exchange
Console timeout 0
vpnclient Server 91.188.180.X
vpnclient mode network-extension-mode
vpnclient nem-st-autoconnect
VPN - L2L vpnclient vpngroup password *.
vpnclient username aradetskayaL password *.
dhcpd auto_config outside_mgts
!
dhcpd update dns replace all two interface inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
SSL-trust ASDM_TrustPoint0 inside point
SSL-trust ASDM_TrustPoint0 outside_mgts point
WebVPN
Select outside_mgts
internal GroupPolicy_91.188.180.X group strategy
attributes of Group Policy GroupPolicy_91.188.180.X
Ikev1 VPN-tunnel-Protocol
internal group VPN - ST strategy
attributes of group VPN - ST policy
value of 195.34.31.50 DNS Server 8.8.8.8
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value VPN-ST_splitTunnelAcl
by default no
aradetskayaL encrypted HR3qeva85hzXT6KK privilege 15 password username
tunnel-group 91.188.180.X type ipsec-l2l
attributes global-tunnel-group 91.188.180.X
Group - default policy - GroupPolicy_91.188.180.42
IPSec-attributes tunnel-group 91.188.180.X
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
remotely IKEv2 authentication certificate
pre-shared-key authentication local IKEv2 *.
remote access to tunnel-group VPN - ST type
VPN-general ST-attributes tunnel-group
address vpnpool pool
Group Policy - by default-VPN-ST
tunnel-group ipsec VPN ST-attributes
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the icmp error
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:212e4f5035793d1c219fed57751983d8
: end

door-71 # sh crypto ikev1 his

There are no SAs IKEv1

door-71 # sh crypto ikev2 his

There are no SAs IKEv2

door-71 # sh crypto ipsec his

There is no ipsec security associations

door-71 # sh crypto isakmp

There are no SAs IKEv1

There are no SAs IKEv2

Global statistics IKEv1
The active Tunnels: 0
Previous Tunnels: 0
In bytes: 0
In the packages: 0
In packs of fall: 0
In Notifys: 0
In the constituencies of P2: 0
In P2 invalid Exchange: 0
In P2 Exchange rejects: 0
Requests for removal in his P2: 0
Bytes: 0
Package: 0
Fall packages: 0
NOTIFYs out: 0

Exchanges of P2: 0
The Invalides Exchange P2: 0
Exchange of P2 rejects: 0
Requests to remove on P2 Sa: 0
Tunnels of the initiator: 0
Initiator fails: 0
Answering machine fails: 0
Ability system breaks down: 0
AUTH failed: 0
Decrypt failed: 0
Valid hash fails: 0
No failure his: 0

IKEV1 statistics for Admission appeals
In negotiating SAs Max: 25
In negotiating SAs: 0
In negotiating SAs Highwater: 0
In negotiating SAs rejected: 0

Global statistics IKEv2
The active Tunnels: 0
Previous Tunnels: 0
In bytes: 0
In the packages: 0
In packs of fall: 0
In Fragments of fall: 0
In Notifys: 0
In Exchange for the P2: 0
In P2 invalid Exchange: 0
In P2 Exchange rejects: 0
In IPSEC delete: 0
In delete IKE: 0
Bytes: 0
Package: 0
Fall packages: 0
Fragments of fall: 0
NOTIFYs out: 0
Exchange of P2: 0
The Invalides Exchange P2: 0
Exchange of P2 rejects: 0
On IPSEC delete: 0
The IKE Delete: 0
Locally launched sAs: 0
Locally launched sAs failed: 0
SAs remotely initiated: 0
SAs remotely initiated failed: 0
System capacity: 0
Authentication failures: 0
Decrypt failures: 0
Hash failures: 0
Invalid SPI: 0
In the Configs: 0
Configs: 0
In the Configs rejects: 0
Configs rejects: 0
Previous Tunnels: 0
Previous Tunnels wraps: 0
In the DPD Messages: 0
The DPD Messages: 0
The NAT KeepAlive: 0
IKE recomposition launched locally: 0
IKE returned to the remote initiated key: 0
Generate a new key CHILD initiated locally: 0
CHILD given to the remote initiated key: 0

IKEV2 statistics for Admission appeals
Max active SAs: no limit
Max in negotiating SAs: 50
Challenge cookie line: never
Active sAs: 0
In negotiating SAs: 0
Incoming requests: 0
Accepted incoming requests: 0
A rejected incoming requests: 0
Out of requests: 0
Out of the applications accepted: 0
The outgoing rejected requests: 0
A rejected queries: 0
Rejected at the SA: 0 Max limit
Rejected low resources: 0
Rejected the current reboot: 0
Challenges of cookie: 0
Cookies transmitted challenges: 0
Challenges of cookie failed: 0

IKEv1 global IPSec over TCP statistics
--------------------------------
Embryonic connections: 0
Active connections: 0
Previous connections: 0
Incoming packets: 0
Inbound packets ignored: 0
Outgoing packets: 0
Outbound packets ignored: 0
The RST packets: 0
Heartbeat Recevied ACK packets: 0
Bad headers: 0
Bad trailers: 0
Chess timer: 0
Checksum errors: 0
Internal error: 0

door-71 # sh statistical protocol all cryptographic
[Statistics IKEv1]
Encrypt packets of requests: 0
Encapsulate packets of requests: 0
Decrypt packets of requests: 0
Decapsulating requests for package: 0
HMAC calculation queries: 0
ITS creation queries: 0
SA asked to generate a new key: 0
Deletion requests: 0
Next phase of allocation key applications: 0
Number of random generation queries: 0
Failed requests: 0
[Statistics IKEv2]
Encrypt packets of requests: 0
Encapsulate packets of requests: 0
Decrypt packets of requests: 0
Decapsulating requests for package: 0
HMAC calculation queries: 0
ITS creation queries: 0
SA asked to generate a new key: 0
Deletion requests: 0
Next phase of allocation key applications: 0
Number of random generation queries: 0
Failed requests: 0
[IPsec statistics]
Encrypt packets of requests: 0
Encapsulate packets of requests: 0
Decrypt packets of requests: 0
Decapsulating requests for package: 0
HMAC calculation queries: 0

ITS creation queries: 0
SA asked to generate a new key: 0
Deletion requests: 0
Next phase of allocation key applications: 0
Number of random generation queries: 0
Failed requests: 0
[SSL statistics]
Encrypt packets of queries: 19331
Encapsulate packets of queries: 19331
Decrypt packets of queries: 437
Package requests decapsulating: 437
HMAC calculation queries: 19768
ITS creation queries: 178
SA asked to generate a new key: 0
Requests to remove SA: 176
Next phase of allocation key applications: 0
Number of random generation queries: 0
Failed requests: 0
[Statistical SSH are not taken in charge]
[Statistics SRTP]
Encrypt packets of requests: 0
Encapsulate packets of requests: 0
Decrypt packets of requests: 0
Decapsulating requests for package: 0
HMAC calculation queries: 0
ITS creation queries: 0
SA asked to generate a new key: 0
Deletion requests: 0
Next phase of allocation key applications: 0
Number of random generation queries: 0
Failed requests: 0
[Statistics]
Encrypt packets of requests: 0
Encapsulate packets of requests: 0
Decrypt packets of requests: 0
Decapsulating requests for package: 0
HMAC calculation queries: 6238
ITS creation queries: 0
SA asked to generate a new key: 0
Deletion requests: 0
Next phase of allocation key applications: 0
Number of queries random generation: 76
Failure of queries: 9
door-71 # sh crypto ca trustpoints

Trustpoint ASDM_TrustPoint0:
Configured for the production of a self-signed certificate.

Trustpoint ASDM_TrustPoint1:
Configured for the production of a self-signed certificate.

If you need something more, then spread!
Please explain why it is that I don't want to work?

Hello

When the IPSEC tunnel does not come to the top, the first thing comes to my mind is to run a tracer of package from the CLI and the phases in it. Please run this command from your firewall side and share the output. I've just compiled this command with the random ip address and ports of your given range.

Packet-trace entry inside tcp 10.1.72.2 1233 10.1.61.2 443 detailed

Best regards

Amandine

ASA 8.3 VPN site-to-site does not UDP traffic to other peer

Hello!!!

Someone turned off the lights :-) I say this because that's 6.2 6.3 I can't get the basic things...

On a SAA, I created a "site-site" VPN profile to connect to a remote site, on the other side (ASA 8.2) sees no problem, I can pass all IP traffic via VPN without NAT; but on a new ASA5505 with 8.3 (1) version fw and ASDM 6.3 (1) can't do that in any way :-(

What I get is trivial...

... It works perfectly with TCP and ICMP traffic, but does not have UDP traffic: in practice, if I followed the traffic to a remote private IP, TCP and ICMP traffic I see only packets in vlan "inside" with the private IP, but with the UDP traffic on top of that, I see traffic on vlan 'out' with the IP public ASA and source port changed :

Inside: UDP to 172.16.2.128:6000 to 172.16.0.200:6000
Outside: UDP to 5.5.5.5:23400 to 172.16.0.200:6000

Why?

Of course, the traffic is not encrypted and does not reach the other side of the tunnel!

Here are the important parts of the configuration:

interface Vlan1
nameif inside
security-level 100
172.16.2.1 IP address 255.255.255.0

network obj_any object
subnet 0.0.0.0 0.0.0.0

remote network object
172.16.0.0 subnet 255.255.254.0

outside_cryptomap to access extended list ip 172.16.2.0 allow 255.255.255.0 network remote control object

NAT (inside, outside) static source any any destination static remote-remote network

network obj_any object

NAT dynamic interface (indoor, outdoor)

card crypto outside_map0 1 match address outside_cryptomap

outside_map0 card crypto 1jeu pfs

card crypto outside_map0 1 set ip.ip.ip.ip counterpart

outside_map0 card crypto 1jeu nat-t-disable

outside_map0 interface card crypto outside

Given that the new business object, I have not yet quite clear (ok, I don't find time to do a deep reading of the documentation), someone is able to direct me to fix this trivial?

Note: If I remove my drive manual nat and I flag "network translating" on the remote network object thus indicate that they want NAT with ip network remote control then don't work any IP vs. remote site traffic. Why, why have not more than the simple rules of 'nat exception' the old version and why the crypto-plan applies only to TCP traffic? Possible that there is an object any which takes all IP traffic?

A big thank you to all.

73,

Arturo

Hi Arturo,.

I know that there is a certain NAT related bugs in 8.3 (1) and although I don't remember a specific which corresponds to your symptoms, I would say you try 8.3 (2) instead, or maybe even the last available version of a temp (currently to 8.3 (2.4):)

http://tools.cisco.com/support/downloads/go/ImageList.x?relVer=8.3.2+Interim&mdfid=279916854&sftType=Adaptive+Security+Appliance+%28ASA%29+Software&optPlat=&nodecount=9&edesignator=null&modelName=Cisco+ASA+5510+Adaptive+Security+Appliance&treeMdfId=268438162&modifmdfid=&imname=&treeName=Security&hybrid=Y&imst=N

If you still see the problem, then, check

entry Packet-trace within the udp 172.16.2.2 1025 172.16.0.1 detail 123

entry Packet-trace inside tcp 172.16.2.2 1025 172.16.0.1 detail 123

and check what's different.

HTH

Herbert

the WAN connection becomes too slow after you have configured the VPN (Site Site)

Hello

I have two branches connected via WAN (MPLS) connection using two 2921 routers.the connection is 2 M.

I set up a VPN between these two sites, but after the connection has become very slow.

y at - it something I can do to speed up the speed of connection.

VPN proposals are:

Proposals of the phase 1: 3DES, pre-shared,.

Phase 2 proposals: esp-3des esp-sha-hmac

I don't think that lower levels of security proposals will add a lot to the speed...

Hi Marc,

one thing you should definitely is a hardware encryption go if you do not already tht, it also reduces the load on your cpu

You can try other things is play with mtu, according to your line mtu and what applications are mainly used. try setting the mtu of at least 60 odd bytes lower than the mtu and also sometimes server line recommended mtu settings like server many have obligation to mtu to 1300 or 1400, if that's not it can cause a lot of re transmissions, you can also try fragmentation before encryption

http://www.Cisco.com/en/us/docs/interfaces_modules/services_modules/VSPA/configuration/guide/ivmvpnb.PDF

Ping of ASA to remote VPN site

I am haivng a weird question. I have two ASA in place with a VPN tunnel from site to site between the two. The traffic is through the tunnel without problem. I have a whole allowed for the two locations on the tunenl IP. The issue I'm having is that when I'm on the ASAs I'm not able to ping what anyone at the remote location. PC between locations communicates very well via the VPN tunnel however.

The reason that I need is to have the ASAs information to syslog for my syslog server appliances. Y at - it something that I'm missing that will allow the ASA contact materials at the remote location?

When you try to ping, do you "ping inside?

Also, your custom logging, haven't you set up "logging inside the host"?

Cannot access remote network by VPN Site to Site ASA

Hello everyone

First of all I must say that I have configured the VPN site-to site a million times before. Stuck with it. First of all I can't ping outside the interface of my ASA remote. Secondly, VPN is in place, but no connectivity between local networks

ASA local:
hostname gyd - asa
domain bct.az
activate the encrypted password of XeY1QWHKPK75Y48j
XeY1QWHKPK75Y48j encrypted passwd
names of
DNS-guard
!
interface GigabitEthernet0/0
Shutdown
nameif vpnswc
security-level 0
IP 10.254.17.41 255.255.255.248
!
interface GigabitEthernet0/1
Vpn-turan-Baku description
nameif outside Baku
security-level 0
IP 10.254.17.9 255.255.255.248
!
interface GigabitEthernet0/2
Vpn-ganja description
nameif outside-Ganja
security-level 0
IP 10.254.17.17 255.255.255.248
!
interface GigabitEthernet0/2.30
Description remote access
VLAN 30
nameif remote access
security-level 0
IP 85.*. *. * 255.255.255.0
!
interface GigabitEthernet0/3
Description BCT_Inside
nameif inside-Bct
security-level 100
IP 10.40.50.65 255.255.255.252
!
interface Management0/0
nameif management
security-level 100
IP 192.168.251.1 255.255.255.0
management only
!
boot system Disk0: / asa823 - k8.bin
passive FTP mode
DNS server-group DefaultDNS
name-server 192.168.1.3
domain bct.az
permit same-security-traffic intra-interface
object-group network obj - 192.168.121.0
object-group network obj - 10.40.60.0
object-group network obj - 10.40.50.0
object-group network obj - 192.168.0.0
object-group network obj - 172.26.0.0
object-group network obj - 10.254.17.0
object-group network obj - 192.168.122.0
object-group service obj-tcp-eq-22
object-group network obj - 10.254.17.18
object-group network obj - 10.254.17.10
object-group network obj - 10.254.17.26
access-list 110 scope ip allow a whole
NAT list extended access permit tcp any host 10.254.17.10 eq ssh
NAT list extended access permit tcp any host 10.254.17.26 eq ssh
access-list extended ip allowed any one sheep
icmp_inside list extended access permit icmp any one
icmp_inside of access allowed any ip an extended list
access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh
RDP list extended access permit tcp any host 192.168.45.3 eq 3389
rdp extended permitted any one ip access list
sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0
NAT-vpn-internet access-list extended ip 192.168.121.0 allow 255.255.255.0 any
NAT-vpn-internet access-list extended ip 172.26.0.0 allow 255.255.255.0 any
NAT-vpn-internet access-list extended ip 192.168.122.0 allow 255.255.255.0 any
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.60.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.50.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 192.168.0.0 255.255.0.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 172.26.0.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.254.17.0 255.255.255.0
GHC-ganja-internet access-list extended ip 192.168.45.0 allow 255.255.255.0 any
Standard access list Split_Tunnel_List allow 192.168.16.0 255.255.255.0
azans 192.168.69.0 ip extended access-list allow 255.255.255.0 any
permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.121.0 255.255.255.0
permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.80.0 255.255.255.0
pager lines 24
Enable logging
emblem of logging
recording of debug console
recording of debug trap
asdm of logging of information
Interior-Bct 192.168.1.27 host connection
flow-export destination inside-Bct 192.168.1.27 9996
vpnswc MTU 1500
outside Baku MTU 1500
outside-Ganja MTU 1500
MTU 1500 remote access
Interior-Bct MTU 1500
management of MTU 1500
IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0
IP local pool ssl 192.168.121.130 - 192.168.121.200 mask 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any outside Baku
ICMP allow access remotely
ICMP allow any interior-Bct
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
global (outside-Baku) 1 interface
global (outside-Ganja) interface 2
3 overall (RAS) interface
azans access-list NAT 3 (outside-Ganja)
NAT (remote access) 0 access-list sheep-vpn-city
NAT 3 list nat-vpn-internet access (remote access)
NAT (inside-Bct) 0-list of access inside_nat0_outbound
NAT (inside-Bct) 2-nat-ganja access list
NAT (inside-Bct) 1 access list nat
Access-group rdp on interface outside-Ganja
!
Router eigrp 2008
No Auto-resume
neighbor 10.254.17.10 interface outside Baku
neighbor 10.40.50.66 Interior-Bct interface
Network 10.40.50.64 255.255.255.252
Network 10.250.25.0 255.255.255.0
Network 10.254.17.8 255.255.255.248
Network 10.254.17.16 255.255.255.248
redistribute static
!
Access remote 0.0.0.0 0.0.0.0 85.*. *. * 1
Outside-Baku route 10.0.11.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.33.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.150.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.170.0 255.255.255.0 10.254.17.10 1
Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1
Route outside Baku 10.254.17.32 255.255.255.248 10.254.17.10 1
Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 192.168.27.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1
Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.66.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1
Outside-Baku route 192.168.80.0 255.255.255.0 10.254.17.11 1
Access remote 192.168.121.0 255.255.255.0 85.132.43.1 1
Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1
Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1
Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1
Route inside-Bct 192.168.254.0 255.255.255.0 10.40.50.66 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol Ganymede GANYMEDE +.
AAA-server GANYMEDE (Interior-Bct) 192.168.1.8
key *.
AAA-server GANYMEDE (Interior-Bct) 192.168.22.46
key *.
RADIUS protocol AAA-server TACACS1
AAA-server TACACS1 (Interior-Bct) host 192.168.1.8
key *.
AAA-server TACACS1 (Interior-Bct) host 192.168.22.46
key *.
authentication AAA ssh console LOCAL GANYMEDE
Console to enable AAA authentication RADIUS LOCAL
Console Telnet AAA authentication RADIUS LOCAL
AAA accounting ssh console GANYMEDE
Console Telnet accounting AAA GANYMEDE
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.1.0 255.255.255.0 Interior-Bct
http 192.168.139.0 255.255.255.0 Interior-Bct
http 192.168.0.0 255.255.255.0 Interior-Bct
Survey community SNMP-server host inside-Bct 192.168.1.27
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto ipsec transform-set newset aes - esp esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac myset2
Crypto ipsec transform-set esp-3des esp-md5-hmac raccess
Crypto ipsec transform-set esp-3des esp-sha-hmac vpnclienttrans
Crypto ipsec transform-set vpnclienttrans transport mode
life crypto ipsec security association seconds 2147483646
Crypto ipsec kilobytes of life security-association 2147483646
raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map
correspondence address card crypto mymap 10 110
card crypto mymap 10 peers set 10.254.17.10
card crypto mymap 10 transform-set RIGHT
correspondence address card crypto mymap 20 110
card crypto mymap 20 peers set 10.254.17.11
mymap 20 transform-set myset2 crypto card
card crypto mymap interface outside Baku
correspondence address card crypto ganja 10 110
10 ganja crypto map peer set 10.254.17.18
card crypto ganja 10 transform-set RIGHT
card crypto interface outside-Ganja ganja
correspondence address card crypto vpntest 20 110
peer set card crypto vpntest 20 10.250.25.1
newset vpntest 20 transform-set card crypto
card crypto vpntest interface vpnswc
vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1
card crypto interface for remote access vpnclientmap
Crypto ca trustpoint ASDM_TrustPoint0
registration auto
name of the object CN = gyd - asa .az .bct
sslvpnkeypair key pair
Configure CRL
map of crypto DefaultCertificateMap 10 ca certificate

crypto isakmp identity address
ISAKMP crypto enable vpnswc
ISAKMP crypto enable outside-Baku
ISAKMP crypto enable outside-Ganja
crypto ISAKMP enable remote access
ISAKMP crypto enable Interior-Bct
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 20
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 40
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Crypto isakmp nat-traversal 30
No vpn-addr-assign aaa
Telnet timeout 5
SSH 192.168.0.0 255.255.255.0 Interior-Bct
SSH timeout 35
Console timeout 0
priority queue outside Baku
queue-limit 2046
TX-ring-limit 254
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Server NTP 192.168.1.3
SSL encryption, 3des-sha1 rc4 - md5 aes128-sha1 sha1-aes256
SSL-trust point ASDM_TrustPoint0 to vpnlb-ip remote access
SSL-trust ASDM_TrustPoint0 remote access point
WebVPN
turn on remote access
SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image
enable SVC
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
internal group ssl policy
attributes of group ssl policy
banner welcome to SW value
value of DNS-server 192.168.1.3
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
group-lock value SSL
WebVPN
value of the SPS URL-list
internal vpn group policy
attributes of vpn group policy
value of DNS-server 192.168.1.3
Protocol-tunnel-VPN IPSec l2tp ipsec
disable the PFS
BCT.AZ value by default-field
ssl VPN-group-strategy
WebVPN
value of the SPS URL-list
IPSec-attributes tunnel-group DefaultL2LGroup
ISAKMP retry threshold 20 keepalive 5
attributes global-tunnel-group DefaultRAGroup
raccess address pool
Group-RADIUS authentication server
Group Policy - by default-vpn
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
IPSec-attributes tunnel-group DefaultWEBVPNGroup
ISAKMP retry threshold 20 keepalive 5
tunnel-group 10.254.17.10 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.10
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
type SSL tunnel-group remote access
attributes global-group-tunnel SSL
ssl address pool
Authentication (remote access) LOCAL servers group
Group Policy - by default-ssl
certificate-use-set-name username
Group-tunnel SSL webvpn-attributes
enable SSL group-alias
Group-url https://85. *. *. * / activate
tunnel-group 10.254.17.18 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.18
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
tunnel-group 10.254.17.11 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.11
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
type tunnel-group DefaultSWITGroup remote access
attributes global-tunnel-group DefaultSWITGroup
raccess address pool
Group-RADIUS authentication server
Group Policy - by default-vpn
IPSec-attributes tunnel-group DefaultSWITGroup
pre-shared key *.
!
type of policy-card inspect dns migrated_dns_map_1
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect sunrpc
inspect xdmcp
inspect the netbios
Review the ip options
class flow_export_cl
flow-export-type of event all the destination 192.168.1.27
class class by default
flow-export-type of event all the destination 192.168.1.27
Policy-map Voicepolicy
class voice
priority
The class data
police release 80000000
!
global service-policy global_policy
service-policy interface outside Baku Voicepolicy
context of prompt hostname

Cryptochecksum:4f35f975ba7a0c11f7f46dfd541d266f
: end
GYD - asa #.

ASA remote:
ASA Version 8.2 (3)
!
ciscoasa hostname
activate the encrypted password of XeY1QWHKPK75Y48j
2KFQnbNIdI.2KYOU encrypted passwd
names of
DNS-guard
!
interface Ethernet0/0
nameif inside
security-level 100
IP 192.168.80.14 255.255.255.0
!
interface Ethernet0/1
nameif outside
security-level 0
IP 10.254.17.11 255.255.255.248
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
nameif management
security-level 100
no ip address
management only
!
boot system Disk0: / asa823 - k8.bin
passive FTP mode
access-list 110 scope ip allow a whole
192.168.80.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.0.0 255.255.0.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
management of MTU 1500
Within 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow all outside
ICMP allow any inside
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside) 0 access-list sheep
Route outside 0.0.0.0 0.0.0.0 10.254.17.9 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.80.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto ipsec transform-set newset aes - esp esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac myset2
life crypto ipsec security association seconds 2147483646
Crypto ipsec kilobytes of life security-association 2147483646
correspondence address card crypto mymap 10 110
card crypto mymap 10 peers set 10.254.17.9
mymap 10 transform-set myset2 crypto card
mymap outside crypto map interface
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 20
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 40
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN

tunnel-group 10.254.17.9 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.9
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns migrated_dns_map_1
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname

Cryptochecksum:1c1ac60e2fb84f65269d15d53f27c21b
: end
ciscoasa # $

Still, I can't ping ASA remote outside from outside of the Local interface. And there is no connectivity between the 192.168.80.0 distance and local don't say 192.168.1.0. I have run out of ideas

Would appreciate any help. Thank you in advance...

If the tunnel is up (phase 1), but no traffic passing the best test is the following:

Add order management-access to the Interior , and then try to PING the intellectual property inside ASA counterpart.

inside x.x.x.x ping --> x.x.x.x is the IP of the ASA peer inside

The test above shows if the traffic passes through the tunnel (check encrypted/decrypted packets of sh cry ips its).

Test on both directions.

Please post the results.

Federico.

Issue of ASA vpn site to site isakmp

Hello

He has been asked to configure on ASA a new vpn site-to-site. For that vpn should I put:

crypto isakmp identity address
crypto ISAKMP allow outside

.. the configuration of my identity crypto isakmp is automatic and isakmp crypto is not enabled on any interface. I love vpn with ike enabled on the external interface. My question is: why should I enable isakmp on the external interface and especially can create disturbances to ike vpn that are already in place?

By elsewhere-group or tunnel-group strategy, it was me asked to set up, the two do not have indication of ike. Never seen this kind of configuration before vpn, something new.

Thank you

Hi, Giuseppe.

The crypto isakmp command activate outside changed ikev1 crypto Enable outside in the new ASA versions you need not enable this.

There is also no need configure isakmp crypto identity address such that it is set to auto.

This command indicates that the tunnel would be negotiated on the basis of the IP address but since it is set to auto it on it own will therefore not need to specify this command.

Yes, you can create a new group policy group for this new tunnel and tunnel and there should be no impact on other tunnels of work.

Kind regards

Aditya

Please evaluate the useful messages and mark the correct answers.

ASA 5505 <>ASA 5510 VPN Site to Site

Try to configure a vpn site-to site beetween an ASA 5505 and a 5510. I can't get anything thrown, there are now debugging messages or the other. I must have done something wrong, I followed this paper: http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080950890.shtml but I can't make it work. Anyone can have a peek at my configs, maybe I forgot something.

OK, if you go ahead and add this command to all two firewalls 'inside access management' and try to one side inside the 10.21.32.10 ping always nothing passing by?

VPN site to Site with NAT (PIX 7.2)

Hi all

I hope for more help with config PIX. TBH I would classify myself as a newb on PIX, only dabbling in it every 6 months or so...

I have to configure a VPN site-to site between our UK and US Office, to replace our frame relay link. I have configured multiple VPN site to site on the before PIX, so am reasonably okay with the appearance of the config of who. What is a new concept for me is the needs of NAT'ing between the IPSEC tunnel.

The U.S. Agency requires us to NAT source addresses (i.e. 192.168.1.0) usable on their side address (i.e. 143.102.89.0). The tunnel must then be set to encrypt traffic between 143.102.89.0/24 and 172.24.0.0/14.

I added the following config and hoping to test it at the U.S. office happens online today.

If I Ping from 192.168.1.0 to 172.24.x.x source and run a SH NAT inside, the NAT translation seems good.

is the intellectual property inside 192.168.1.0 255.255.255.0 outside 172.24.0.0 255.252.0.0
static translation at 143.102.89.0
translate_hits = 4, untranslate_hits = 0

Could someone please go through the following lines of config and comment if there is no error?

Thank you very much

Kevin

/ * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-margin : 0 cm ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

IP 143.102.89.0 allow Access-list ipsec - dallas extended 255.255.255.0 172.24.0.0 255.252.0.0

policy-nat-dallas-list of allowed extensive access ip 192.168.1.0 255.255.255.0 172.24.0.0 255.252.0.0

public static 143.102.89.0 (inside, outside) - list of access policy-nat-dallas

Crypto ipsec transform-set esp-3des esp-md5-hmac 3desmd5set

card crypto map dyn 40 correspondence address ipsec - dallas

set dyn-map 40 crypto map peer 143.101.6.141

card crypto dyn-map 40 transform-set 3desmd5set

dyn-map interface card crypto outside

crypto isakmp identity address

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

md5 hash

Group 2

life 86400

tunnel-group 143.101.6.141 type ipsec-l2l

IPSec-attributes tunnel-group 143.101.6.141

pre-shared-key *.

You can configure NAT/Global pair for the rest of the users.

For example:

You can use the initially configured ACL:

policy-nat-dallas-list of allowed extensive access ip 192.168.1.0 255.255.255.0 172.24.0.0 255.252.0.0
NAT (inside) 1 access list policy-nat-dallas

Global 1 143.102.89.x (outside)

The static statement that you configured previously will take precedence over the above. So the printer gets statically using a NAT to 143.102.89.10, and the rest can do another ip address 143.102.89.x PATed.

Please note that for PAT, traffic can only be initiated from 192.168.1.0/24 LAN to 172.24.0.0/14, not the other way around.

Hope that helps.

[VPN Site-to-Site] Network that overlap

Hello

We have a Cisco ASA 9.1 and many VPN clients that work very well to this topic.

Now, he must connect to a partner with VPN Site to Site site.

We have a few problems:
- Duplication of IP address (we use 10.145.0.0/16 10.0.0.0/8 and partner use)
- Partner cannot use NAT on the router
What are the best solutions to configure the VPN Site to Site?

Thanks for your help,

Patrick

Hi Patrick,

Best option here is that you can specify the required subnets only in the field of /encryption cryptomap...

said in other 10.0.0.0/8 need access only a few subnets 10.1.0.0/24, 10.10.20.0/24... You can specify only in your crypto acl... Alternatively, you can use refuse instruction for the specific 10.145.0.0/16 crypto card but am not sure if this gives you the best result.

If you have the required access is mixed with several 10.x.x.x/8 instructions... then you can have the crypto ACL like sub areas of encryption... Here you jump only 10.145.0.0/16 of the subnet range...

10.0.0.0/9 to 10.145.0.0/16
10.128.0.0/12 to 10.145.0.0/16
10.146.0.0/15 to 10.145.0.0/16
10.148.0.0/14 to 10.145.0.0/16
10.152.0.0/13 to 10.145.0.0/16
10.160.0.0/11 to 10.145.0.0/16

10.192.0.0/10 to 10.145.0.0/16

but make sure you have not all servers in 10.145.0.0/16 on your local network that the client requires access...

Link to have refuse to crypto ACL'; s

https://supportforums.Cisco.com/discussion/10909276/crypto-ACL-question

Concerning

Knockaert

[VPN site to Site] Are route explicit LAN remote necessary?

Hello

I have configured the VPN Site to be used inside the interface of the ASA (9.4.1)

site2site_inside.jpg
1. The computer in the Zone 1 (192.168.1.1), I can access the Intranet all and it works without a problem--> all traffic through the VPN.
For example, I can use 10.0.0.1 on remote desktop.

2. in the other direction, 10.0.0.1, I try to use the remote desktop on 192.168.1.1, the traffic is not routed over the VPN.

Journal: ' build incoming TCP connections to inside:10.0.0.1/1539 outdoors: 192.168.1.1/3389.

In case 1 (when it worked), he says "build the incoming TCP connection for inside:192.168.1.1/2039 to inside:10.0.0.1/3389.

To fix it, I had to add specific route on ASA: 192.168.1.0/24 inside

It works on both directions.

Is this a normal behavior?

I thought that cryptomap and IPSec SPI would be sufficient.

Thank you

Patrick

Yes, because the cryptomap is mapped to the output interface. The research of the way occurs before you hit the cryptomap. The opposite lane works because you already have a connection (in which are defined interfaces to use).

VPN Site to Site not upward Tunel on a router

Hello

First time I try to configure the VPN Site to Site on the two routers X and Y. I use cisco SDM

X router that I have set up on this path http://www.tekkom.dk/mediawiki/images/e/ee/IP_sec_site-to-site_sdm.pdf

Then I create a mirror and spent on router Y I tunel up VPN router Y.

But I have problem with router X. When I try to the top of Tunel, I have two problems:

The peer must be routed through the crypto map interface. The following host is routed through the non-crypto map interface. (1) 79.*. * **. **

(79.* *-it is the WLAN router address Y)

Destination of traffic of the tunnel must be channelled through the crypto map interface. The destination following (s) is routed through non-crypto map interface. (1) 10.*. * **. **

(10.* *. *-is router LAN address Y)

Configuration of routers in the files.

Apologies for the lack of your answer.

You have the same card encryption applied to the physical interface and dialer0 interface. You can try removing it from the dialer0 interface and a new test.

If it does not can try you backwards IE. remove physical and apply to the dialer0 only.

Jon

Split tunneling VPN site-to-site

Dear all,

I have two ASA 5510 with VPN site-to-site, I can send all Internet traffic to the central site (HQ),

How to set the split tunneling to access Campus LAN (192.168.2.0/24) of LAN2.

Thank you in advance.

Best regards

Zoltan

You can have 'decline' instruction on your ACL crypto and he will deviate the traffic is encrypted to the site-to-site VPN tunnel.

For ASA 1:

access-list extended 100 permit ip 10.10.16.192 255.255.255.192 10.10.16.128 255.255.255.192

access-list extended 100 permit ip 10.0.0.0 255.0.0.0 10.10.16.128 255.255.255.192

access-list extended 100 deny ip 192.168.2.0 255.255.255.0 10.10.16.128 255.255.255.192

access-list extended 100 permit ip any 10.10.16.128 255.255.255.192

For ASA 2:

access-list extended 100 permit ip 10.10.16.128 255.255.255.192 10.10.16.192 255.255.255.192

access-list extended 100 permit ip 10.10.16.128 255.255.255.192 10.0.0.0 255.0.0.0

access-list extended 100 deny ip 10.10.16.128 255.255.255.192 192.168.2.0 255.255.255.0

access-list extended 100 permit ip 10.10.16.128 255.255.255.192 all

Hope that helps.

ASA Configuration of VPN Site to Site - NAT issues

Similar Questions

site2site_inside.jpg

Maybe you are looking for