Solve WiFi problems after upgraded 9.3

Similar Questions

• WiFi problem after upgrade to Windows 10

  Greetings!

  I read a few posts on WiFi problems after the (improper) upgrade of Windows 10. I have a ThnkPad T530 which I've upgraded to Windows 10 Windows 7 in September (too late to roll back). Here's my question:

  I have three computers on my desk. This standard T530 running Windows 10, a ThnkPad E555 running Windows 7 and a Dell running Windows 8. I used all three last Friday. I installed Norton on all three Friday and everything went without a hitch. When I first started their return to the top of this morning, the two others came online as usual. The ThinkPad T530 connected by a router in the company, but has no access to the internet. I can connect to the hotspot on my phone and it connects fine. I tried to turn the WiFi connection and then turn it on again, restart, by killing and restarting the business connection, etc. Nothing changes.

  Help, please

  Ben

  Try the following:

  Open administrator command prompt:
  http://winaero.com/blog/how-to-open-elevated-command-prompt-in-Windows-10/

  Then, run this command:
  netsh int ip reset c:\resetlog.txt

• Pavilion laptop g6 - Wifi problem after upgrade to 8.1 Windows

  KIM

  I have a Pavilion Notebook - C3M29EA #AB7 g6 and upgraded to 8.1 windows yesterday.

  Since then, I was unable to detect my own wifi connection while I am able to detect my neighbours. (Everything worked fine before the update).

  Any suggestions?

  -Same here.

  After an hour of time I will ever come back that I solved the problem.

  (1) go on the internet via the wired LAN port

  2) update drivers for Ralink wifi adapter

  Go: Right click on the wireless network connection icon: properties/Configure/tab Driverr/update driver

  (3) after a minute or two of updateing the PC reports that the driver has been updated

  (4) pull the network cable and turn on WiFi.

  What a pain in the anus,

  Anyway, as I said, corrected!

  Dansda.

• K3 Note Wifi problem after upgrade to the marshmallow

  Guys, after upgradation of Marshmallow in k3 note, there arise a problem of wifi, it just dropeout every minute like connect for 1-2 seconds and disconnect then automatic...
  If someone knows how to fix this please tell me... I have hard reset my phone but the problem is not solved... so please tell me the solution

  Note from the admin; phone added to the subject type

  
  

• Intermittent WiFi problem after upgrade to Windows 10

  My acer aspire V3 - 571 has been intermittently lose WiFi for the last 2 days since Windows 10 Windows 7 Home Premium upgrade.

  The Aspire has:

  Driver Atheros wireless network adapt AR5BWB222 10.0.0.38 Wednesday 2/15/12

  So far, I have:

  1. in the properties Atheros AR5BWB222 Wireless Network Adapter, I unchecked the box in the tab property management who read allow the computer to turn off this device to save power.

  1B. Made sure flight mode was in the off position.

  1 c. Forget exactly where I did, but made certain settings in another? location have been set to "Maximum Performance".

  2. check that the firmware is updated on my network router, the value 2 of WPA - PSK (AES) security.

  3. search through many forums to read the responses of people upgrading Windows 10 WiFi issues - seems it is a widespread problem, although no one said that the WiFi signal loss was intermittent, as is my laptop. Shots of the Internet for my research also shows WiFi problems occurred in the past for installation of Windows 8. (So far have not come across mentions of WiFi problems for the latest installations of Windows 7).

  4. in exploring my laptop, I came across a page of Microsoft Updates - SEE ATTACHED. I was surprised to find that these updates go out quite frequently during the day. For example, 10 separate updates between 23:30 and 16:24 on August 1 and 18 separate updates between 12 h 06 at 15:57 on August 2.  Included in the record of updates for August 1 and August 2. I am aware that Microsoft uses my WiFi to download updates AUTOMATICALLY. It is possible that this intermittent intermittent interruptions of the WiFi update download?

  5. this afternoon, when the WiFi did not work for Windows 10. I reinstalled as a dual boot Ubuntu 14.04. I have had no trouble to connect to the WiFi for Ubuntu.

  Not yet:

  1. I haven't tried connecting the laptop via an Ethernet cable to my router during one of these WiFi failure.

  2. my ISP is a VOIP/Internet, using a Westell and a single Cisco router configuration. I have not taken into account if they can be a cause of the problem.

  3. I read on a forum that someone corrected their problem with WiFi connection by changing their setting include TKIP security router

  NOTE: I need to put Windows screenshot attachment 10 updates in a response email separate to this post as this post does not accept the attachment.

  Would appreciate your comments and suggestions. Thanks in advance.

  I'll probably also put this on a Windows 10 forum elsewhere.

  Hello!

  FYI, this has worked for me, finally a solution!

  The strangest thing - I have uninstalled the driver Atheros. Do NOT reinstall it. After uninstalling the driver Atheros, a right screen Windows 10 panel immediately appeared style - either on advice of Panel or in the page settings of WiFi, was asleep, can't remember which - that contains an entry box marked my wifi password. I entered the password and boom, the wifi worked. He has been since.

  Once again thank you. Mark resolved.

• WiFi problem after upgrade to OS 10.11.2

  Hello

  I have a MBP 2010 I installed OS 10.11.2 yesterday because it was supposed to improve the performance of the wifi.

  Since my update the MBP does not see any network wifi more so that all of the other ipad and iphone at home are connected.

  I don't know how to activate the wifi to work again.

  Thank you for your help

  You have restarted your Mac since the upgrade? If this is not the case, try this, because sometimes a reboot solves things.

  You can also try a reset of the PRAM.

  If none of the above work:

  Try to turn WiFi off tension, and then back on... Or...

  Attempt to remove networks that you have connected to in System Preferences/network/WiFi/Advanced button/Preferred Networks. Then see if you are able to connect to a network... Or...

  Finally to try: System/Network Preferences, remove the entry from WiFi by selecting it in the networks list and clicking on the sign less . You may need to open the Panel with an administrator account and password. Then add the WiFi network, by clicking on the plus sign by selecting from the drop-down list WiFi Interface .

• Latitude E5520 Audio problems after upgrade to win 10

  I have audio problems after upgrade to win 10 64-bit.

  Dell Latitude E5520 IDT 92HDxxx HD Audio
  Hardware ID:
  HDAUDIO\FUNC_01 & VEN_111D & DEV_76E7 & SUBSYS_1028049A & REV_1001
  HDAUDIO\FUNC_01 & VEN_111D & DEV_76E7 & SUBSYS_1028049A

  (1) if I use the built-in driver to Win 10 ("high definition Audio Device") I hear speakers/headphones and switching between the speakers and the works of helmet very well but my laptop computer microphone does not work ("not connected").

  (2) if I use the latest Dell driver (IDT 92HDxxx HD Audio Driver) I hear initially via speakers, but as soon as I plug in headphones I can't switch back to the speakers (i.e. switching between the speakers and the headphones does not work) and my laptop computer microphone works.

  I would be happy to provide more information and help to debug.

  To a Microsoft Community Forum, I received the following reply from Rob Brown - Microsoft MVP:

  *************************************************************************
  Hello
  AS OEM Dell is responsible for the good operation of the equipment both
  and Windows. Check their documentation online with Dell Support, and
  drivers and ask questions in the forums about known problems. Make sure that you are
  Run the latest version of the BIOS, chipset and drivers.
  I hope this helps.
  *************************************************************************

  I understand that the Latitude E5520 does not appear on the Dell "Computers tested for upgrade to Windows 10" list... However I was hoping maybe Dell could find in the goodness of their hearts to a updated driver IDT 92HDxxx... pretty please?

  Thank you
  John D.

  johnsdagg

  AS OEM Dell is responsible for the good operation of the equipment both
  and Windows.

  Hi, John. It's quite nervous of a member of the MS forum say that Dell is responsible to operate Windows. It wasn't Dell but MS who claims that Win10 has most of the necessary drivers and if not then the drivers Win7 and Win8.1 would work.

  johnsdagg

  I was hoping that maybe Dell could find in the goodness of their hearts to a updated driver IDT 92HDxxx... pretty please?

  I doubt that it is possible for two reasons. Dell went from IDT Realtek as the audio seller so probably not more a a contract with IDT, if IDT even exist anymore. A year ago IDT was acquired by another company. I do not know its current status, but it is sure that the acquiring company will not be upgrading old software IDT. Reference Dell itself does not write the audio drivers. Even when IDT was the seller I believe that Win7 drivers are the final versions - no version 8 or 8.1 I think.

  johnsdagg

  If I use the built-in driver to Win 10 ("high definition Audio Device") I hear speakers/headphones and switching between the speakers and the works of helmet very well but my laptop computer microphone does not work ("not connected").

  The native Windows audio driver can't stand struggling external mic. It is a MS 'known problem '. MS must implement a decision-making support, but there is no indication that it will be. Meanwhile, you have two workaround solutions. You can switch backwards between the natives and the IDT drivers. At some point Win10 could leave the IDT driver works correctly. Or get an outlet cheap usb audio to the microphone. Struggling running out-audio driver usb Windows native usb and so dependent no driver IDT.

• Dell XPS Ultrabook 12 has network using WIFI connection problem after upgrade to Windows 10

  I have a Dell laptop XPS Ultrabook 12 that worked fine on Windows 8.1. When Microsoft prompted me to sign up for upgrade to Windows 10, I hesitated, but finally, I signed up for it. In recent months, I have been asked several times upgraded to Windows 10 but I just ignored and delay the update as much as possible, because I need to work with the laptop and I can't afford to have problems after the upgrade.  To my horror, Microsoft forced an install of Windows 10 this morning without allowing me to delay and just after the upgrade, I can't connect to my existing network. I have therefore no access to the internet and I am currently typing this complaint using another PC. I noticed that the laptop can connect to the network automatically when I walk my router but the connection will last only a few minutes, and then he'd cut off. I tried to connect and the message I get is "unable to connect to this network. I checked with "ipconfig/all", wifi said media disconnected. I checked with the Dell support website and downloaded and installed a newer driver, but the problem persisted. Apparently the surf on the internet, this problem is faced with a number and any suggestions to fix do not work (after that I tried).

  Help, please.

  You should be able to go back to 8.1 for Windows by following the instructions here:

  https://www.YouTube.com/watch?v=2Y3uc2FWlK0&index=3&list=PL1RkaknDn7v-w5LEVIDvTCvmKZ_1_NcZz

• Don't sign in business Wifi network after upgrade to Lollipop

  Hello

  After the upgrade to Lollipo my Xperia Z2 is unable to connect to my corporate wifi network. It shows just like white screen after I click on the sign in the notificaions network.

  Please suggest how to solve this problem.

  Thank you

  Sandeep

  Hello

  I did not try it, but I tried to install the mozilla browser and I tried to open google, then it took to the login page of my business network. After I signed, I was able to navigate.

  Thank you

  Sandeep

• iPhone 6s + had some problems after upgrade to iOS 9.3.2

  1st issue is the battery. Already before the upgrade to iOS 9.3.2 since iOS 9.3.1 my battery iphone 6 s + last latency time approximately 40 hours. Now after the upgrade to iOS 9.3.2,and it last only 15 hours. I noticed that the battery went from 100% to 60% in 8 hours without using it. I change all the settings after upgrade.

  2nd question is Siri Spotlight search Suggestion. I see more suggestion of Siri (recent call log and recent applications) in the Spotlight search. I also noticed that, to start the Spotlight search, I need to get to the bottom of the home screen. Previously on iOS 9.3.1 when I push upwards, search Spotlight is cancelled and return to the home screen. Now in iOS 9.3.2,and it no longer works.

  I also-hard reset by pressing Start button / stop and the "home" button together until I see the apple logo. Who will not help too.

  Have you checked the battery in use/settings/battery? All apps using the battery more than usual?

  If the power to restart the phone did not help, the next step after that which could be set back to factory settings and restore form the last backup, especially if you updated using the option 'Over the Air '.

  Use iTunes to restore your device to factory settings - Support Apple iOS

  For some users, removal and establishment of post counts once again solved the problem for others, connecting to iCloud and connect again after you stop the farm by a restart of drain.

• Right-click on the image with link problem after upgrade to 11.0

  After the upgrade, whenever I do a right-click on an image with a link, it opens the link rather than opening a menu drop-down. Any idea on what is causing this behavior?

  OK, think about it. Extension: Tab Utilities was the origin of the problem. Uninstall completely solved the problem, disable it does not solve it.

• ScanDisk USB Flash Drive problem after upgrade to El Capitan

  After the upgrade to El Capitan, I can't access the vault secure on my USB Cruzer facet flash drive. I have Plug and display files as usual but when I try to open the safe, I get the message ' Scan Disk Secure Access V 2.0 requires San Disk USB Flash Drive. Please insert one. »

  The Flash Player has worked fine before the upgrade to El Capitan and I can still use the files outside of the secure vault but, basically, I cannot now access the secure vault. I'd appreciate any thoughts on how this can be resolved. I only am not an expert so please, keep it pretty simple.

  Sounds like a problem of compatibility with the Secure Access software and the OS X El Capitan of SanDisk.  Try download and install the latest version of Secure Access of SanDisk.

  It seems also be other users having the same problem, you may get better assistance with this through SanDisk.  Someone else said that upgrading to the latest version of Secure Access has solved the problem.

  http://forums.SanDisk.com/T5/SanDisk-SecureAccess-2-0/SecureAccess-2-0-and-El-CA Dube/td-p/347378

• Problem after upgrade or install Microsoft SP2

  Hello
  I have a windows xp computer 2004
  I recently had to format my pc and when I reached and installed windows net framework 2 which is correct, but when I installed microsoft service pack 2, that would no longer be my pc access upgrades from microsoft or some other web pages!
  I received the message cannot display the page and no internet conection when I'm connected to the internet?
  I can get the correct browser page
  So I had to uninstall SP2 for microsoft access
  I tried updating my drivers, but have been informed that there is no better match!
  My pc is now at the stage where it wants to install the SP2 of Microsoft but I don't know how to avoid or solve the problem that I get that I reinstalled SP2 about 3 times
  because I contacted help and support just to be told to go to the FAQ site "very useful and not."
  I would be very gratefull if anyone can help me with this quest!
  Thank you very much
  wazuup

  Personal data backup (which none should be considered 100% reliable at this point) then format the HARD disk and do a clean install of Windows.  Please note that a repair installation (upgrade AKA on-site) won't fix this!

  HOW to do a clean install of Windows XP: see method 1 and http://michaelstevenstech.com/cleanxpinstall.html#steps in http://support.microsoft.com/kb/978307

  Once installed the clean, you will have the equivalent of a "new computer" in order to take care of everything on the next page before connecting the machine to the internet or one local network (i.e. other computers) otherwise and before using a flash drive or the SD card that is not brand new, or has not been freshly formatted:

  4 steps to help protect your new computer before going online
       http://www.Microsoft.com/security/pypc.aspx

  Other useful references include:

  HOW to get a computer that is running Windows XP Gold (no Service Pack) fully patched (after a clean install)
  http://groups.Google.com/group/Microsoft.public.windowsupdate/MSG/3f5afa8ed33e121c

  HOW TO get a computer that is running Windows XP SP1 (a) or SP2 fully patched (after a clean install)
  http://groups.Google.com/group/Microsoft.public.WindowsXP.General/MSG/a066ae41add7dd2b

  Tip: After getting the computer fully patched, download/install KB971029 manually: http://support.microsoft.com/kb/971029

  NB: No matter what Norton or McAfee free trial which is preinstalled on the computer when you bought will be reinstalled (but invalid) when Windows is reinstalled. You MUST uninstall the trial for free and download/run the removal tool before installing updates, Windows Service Packs, or updates IE and before installing your new anti-virus application (which will require WinXP SP2 must be installed).

  Norton Removal Tool
       FTP://ftp.Symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

  McAfee Consumer product removal tool
       http://download.McAfee.com/Products/Licensed/cust_support_patches/MCPR.exe

  If these procedures look too complex - and there is no shame in admitting this isn't your cup of tea - take the machine to a local, good reputation and stand-alone computer (that is, not BigBoxStoreUSA or Geek Squad) repair facility.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Latitude E5500 Intel GMA pixels problem after upgrade of RAM > 4 GB

  Hello, I use latitude e5500 with the following specifications:

  • Processor: intel core 2 duo
  • graphic: Intel GMA 4500 MHD
  • OS: Windows 7 SP1 64-bit
  • RAM: 6 GB (2 + 4) 800 MHz

  Recently I have upgraded RAM of 4 GB (2 + 2) 6 GB (2 + 4). They are of the same manufacturer, the two 800 MHz I checked the new memory with the Dell diagnostics - it's ok. After upgrade, I have a serious graphics - parts of my get pixelated screen problems. It is irregularly, with different applications ran - see the screenshot.

  I tried to uninstall the graphics driver - it's ok, but I'm not ;) mode 640 x 480 I have tried different drivers - no improvement. Also, I removed a 2 GB - it works very well with my new 4GBs

  

  Hello

  Yes, I solved the problem. I had to buy an another 4 GB from the same manufacturer with the same properties. With 4 GB + 4 GB, it works perfectly.

  Concerning

  Aleksander

• Keyboard problem after upgrade to 6.0

  Hello everyone

  I used 5.5 of Vmware Vsphere ESXI and Vcenter 5.5 without any problem of keyboard on the remote console on the guest operating system (win 7) after upgrade to esxi, vcenter 6.0 and 6.0, I have problems with the keyboard on the guest remote operating system, note I use french keyboard.

  french keyboard is also used by the operating system remotely.

  How can I solve this problem, so when I try the console remotely on the guest operating system display does'nt English keyboard us keyboard

  Thank you

  the problem is still persisting when using the web console, but when you use the remote console MRC the keyboard works normally