K3 Note Wifi problem after upgrade to the marshmallow

Similar Questions

• WiFi problem after upgrade to Windows 10

  Greetings!

  I read a few posts on WiFi problems after the (improper) upgrade of Windows 10. I have a ThnkPad T530 which I've upgraded to Windows 10 Windows 7 in September (too late to roll back). Here's my question:

  I have three computers on my desk. This standard T530 running Windows 10, a ThnkPad E555 running Windows 7 and a Dell running Windows 8. I used all three last Friday. I installed Norton on all three Friday and everything went without a hitch. When I first started their return to the top of this morning, the two others came online as usual. The ThinkPad T530 connected by a router in the company, but has no access to the internet. I can connect to the hotspot on my phone and it connects fine. I tried to turn the WiFi connection and then turn it on again, restart, by killing and restarting the business connection, etc. Nothing changes.

  Help, please

  Ben

  Try the following:

  Open administrator command prompt:
  http://winaero.com/blog/how-to-open-elevated-command-prompt-in-Windows-10/

  Then, run this command:
  netsh int ip reset c:\resetlog.txt

• Intermittent WiFi problem after upgrade to Windows 10

  My acer aspire V3 - 571 has been intermittently lose WiFi for the last 2 days since Windows 10 Windows 7 Home Premium upgrade.

  The Aspire has:

  Driver Atheros wireless network adapt AR5BWB222 10.0.0.38 Wednesday 2/15/12

  So far, I have:

  1. in the properties Atheros AR5BWB222 Wireless Network Adapter, I unchecked the box in the tab property management who read allow the computer to turn off this device to save power.

  1B. Made sure flight mode was in the off position.

  1 c. Forget exactly where I did, but made certain settings in another? location have been set to "Maximum Performance".

  2. check that the firmware is updated on my network router, the value 2 of WPA - PSK (AES) security.

  3. search through many forums to read the responses of people upgrading Windows 10 WiFi issues - seems it is a widespread problem, although no one said that the WiFi signal loss was intermittent, as is my laptop. Shots of the Internet for my research also shows WiFi problems occurred in the past for installation of Windows 8. (So far have not come across mentions of WiFi problems for the latest installations of Windows 7).

  4. in exploring my laptop, I came across a page of Microsoft Updates - SEE ATTACHED. I was surprised to find that these updates go out quite frequently during the day. For example, 10 separate updates between 23:30 and 16:24 on August 1 and 18 separate updates between 12 h 06 at 15:57 on August 2.  Included in the record of updates for August 1 and August 2. I am aware that Microsoft uses my WiFi to download updates AUTOMATICALLY. It is possible that this intermittent intermittent interruptions of the WiFi update download?

  5. this afternoon, when the WiFi did not work for Windows 10. I reinstalled as a dual boot Ubuntu 14.04. I have had no trouble to connect to the WiFi for Ubuntu.

  Not yet:

  1. I haven't tried connecting the laptop via an Ethernet cable to my router during one of these WiFi failure.

  2. my ISP is a VOIP/Internet, using a Westell and a single Cisco router configuration. I have not taken into account if they can be a cause of the problem.

  3. I read on a forum that someone corrected their problem with WiFi connection by changing their setting include TKIP security router

  NOTE: I need to put Windows screenshot attachment 10 updates in a response email separate to this post as this post does not accept the attachment.

  Would appreciate your comments and suggestions. Thanks in advance.

  I'll probably also put this on a Windows 10 forum elsewhere.

  Hello!

  FYI, this has worked for me, finally a solution!

  The strangest thing - I have uninstalled the driver Atheros. Do NOT reinstall it. After uninstalling the driver Atheros, a right screen Windows 10 panel immediately appeared style - either on advice of Panel or in the page settings of WiFi, was asleep, can't remember which - that contains an entry box marked my wifi password. I entered the password and boom, the wifi worked. He has been since.

  Once again thank you. Mark resolved.

• WiFi problem after upgrade to OS 10.11.2

  Hello

  I have a MBP 2010 I installed OS 10.11.2 yesterday because it was supposed to improve the performance of the wifi.

  Since my update the MBP does not see any network wifi more so that all of the other ipad and iphone at home are connected.

  I don't know how to activate the wifi to work again.

  Thank you for your help

  You have restarted your Mac since the upgrade? If this is not the case, try this, because sometimes a reboot solves things.

  You can also try a reset of the PRAM.

  If none of the above work:

  Try to turn WiFi off tension, and then back on... Or...

  Attempt to remove networks that you have connected to in System Preferences/network/WiFi/Advanced button/Preferred Networks. Then see if you are able to connect to a network... Or...

  Finally to try: System/Network Preferences, remove the entry from WiFi by selecting it in the networks list and clicking on the sign less . You may need to open the Panel with an administrator account and password. Then add the WiFi network, by clicking on the plus sign by selecting from the drop-down list WiFi Interface .

• Bootcamp problem after upgrade of the El Capitan!

  Hello

  I just upgraded to El Capitan Yosemite on my iMac, so I can't find my bootcamp. I tried to do with lonely T instructions, but yet, I think I did something wrong (not very tech savvy just follow the instructions). Bootcamp volume appears in the finder and accessible but non-startup disk. Protection of the integrity of the system has been disable by running csrutil the command disable on recovery mode. I need help!

  additional notes: I have an extra partition named Extra, and I went through the same process using gdisk when I added the partition when using Yosemite. He works at this time, but not now after El Capitan upgrade.

  And I realize that I don't have "No CoreStorage groups of logical volumes found".

  

  Not sure if necessary additional info:

  

  

  Thanks in advance, please guide me in the process.

  Derrick

  Please enter 'p' to the list of files in the last Data MS and after the release. What does the 'Extra' on your Mac partition? Do you have 'lost' Windows when you created "Extra"?

• Z3 messaging, contacts, system settings and more unresponsive after upgrade to the marshmallow

  most of my function of system such as e-mail, contacts, settings storage system no longer works when I just have to upgrade to Android Marshmallow.

  @Hippopothomas

  If you updated over the old system, I suggest you to back up your important data and run a repair using PC Companion software.

• Pavilion laptop g6 - Wifi problem after upgrade to 8.1 Windows

  KIM

  I have a Pavilion Notebook - C3M29EA #AB7 g6 and upgraded to 8.1 windows yesterday.

  Since then, I was unable to detect my own wifi connection while I am able to detect my neighbours. (Everything worked fine before the update).

  Any suggestions?

  -Same here.

  After an hour of time I will ever come back that I solved the problem.

  (1) go on the internet via the wired LAN port

  2) update drivers for Ralink wifi adapter

  Go: Right click on the wireless network connection icon: properties/Configure/tab Driverr/update driver

  (3) after a minute or two of updateing the PC reports that the driver has been updated

  (4) pull the network cable and turn on WiFi.

  What a pain in the anus,

  Anyway, as I said, corrected!

  Dansda.

• HTP.p does not like usual after upgrade to the apex 4.2.6

  Hello everyone,

  We have recently upgraded the Apex 4.0.2 on Oracle 11 g using Embedded PLS door of entry to the Apex 4.2.6 on Oracle 11 g using ADR.

  The initial series of unit tests seemed well until a few questions supported around "htp.p".

  The scenario is like this:

  1. the user fills some fields on the page-10 and click the Save"" button.

  2. This button then performs a redirection to a pop up page where some inputs more are invited to enter.

  3. when the user clicks "OK" on the popup:

  i. an anonymous PLSQL block is executed in the backend (as after presenting processes).

  II. another PLSQL block is executed, which closes the popup windows and returns the control to the parent page.

  This is achieved using htp.p...

  For example:

  HTP.p ("< body > '");

  HTP.p ("< script type =" text/javascript "> '");

  HTP.p ("var alertMsg =" &. P38_PO_AMOUNT has been paid";");)

  HTP.p ('javascript:Alert (alertMsg)');

  HTP.p ("window.opener.location.href =" f? p = & APP_ID.:7: & SESSION.) " ;") ;

  HTP.p('window.) Close (this);') ;

  HTP.p ("< /script >" ");

  HTP.p ("< /body >" ");

  The anonymous block under step 3.i. is well executed and done what it takes in the backend.

  Its the next step which is driving me crazy, I tried to add debugging but to no avail.

  The weird part is that the message "& P38_PO_AMOUNT. has been paid' getting appears on the pop-up itself instead of parent.

  Any ideas or pointers to this problem would be a great help. I have come to the forums and metalink for any position and had no luck so far.

  Kind regards

  Madhu.

  Hi Sunil,

  Thanks for the reply and apologize for the delay in responding.

  But 2 doubts which do not appear in your code:

  1. why you placetag through PTH again? Body will be already present on the page 7

  2. What is "this" in your window close event? 'this' will be indefinite in my opinion

  Thetag and the reference to 'this' was used because the application was developed first on Apex 3.x

  This piece worked through the upgrade to 4.0.2 and it starts to play up only after this upgrade (to 4.2.6).

  I had followed the suggestions from the link you posted, made some changes and the flow is as follows:

  1, as well as the original

  2 as well as the original

  3. when the user clicks "OK" on the popup:

  i. an anonymous PLSQL block is executed in the backend, under process, like submit it: after calculations & Validations.

  II. the 2nd block PLSQL for close & redirect the page is now part of 'Branch of PL/SQL procedure' with branch point ' on Submit: after the treatment (after calculation, Validation and treatment). The PLSQL code is as follows:

  BEGIN
    htp.p('');
  END;
  

  The behavior is always the same and seems not to have changed. I'm a little lost, try different options.

  I'll try to reproduce the scenario on apex.oracle.com and in the meantime of inputs/suggestions would be helpful.

  Kind regards

  Madhu.

• Solve WiFi problems after upgraded 9.3

  After installing iOS 9.3 on my mini iPad, the device could not connect to my Airport network.

  The busy light was all the time spinnig, but the connection never got established.

  I could press the i key to display the IP etc but all entries were completely empty.

  I have zero network and turn on the unit and goes out, but not had any luck.

  I then abandoned static DHCP and all typed manually and suddenly everything started working, the busy flag disappeared and the symbol of a Wi - Fi connection appeared in the status bar!

  This seems to be a good workaround for now, maybe someone finds it useful.

  To close!

• Xperia double Z3, slow after upgrade to the marshmallow

  My double z3 updated last night (~ 1 GB throughout the app 'software update'), but it slows down the passage of open applications, view contacts, view the settings and just about anywhere you can think of a phone.

  I update another double of z3 and everything is OK? No! This is the best, with numerous app I have on it.
  Viva Sony

• Scan C5180 not working after upgrade of the mavericks

  After upgrading my Macbook Air to the operating system of Mavericks, my software of scan C5180 does not include the overview / dots a longer selection.  These are the points that allow you to select only part of the image of bed scanner for treatment.

  The scanner / printer software has been updated by the o/s update Lion to the Mavericks.

  MacBook Air does not include a CD option, so I can't go back to the original driver.

  Thanks, but none of it helped.

  I got running again by installing an older driver from a site "archived drivers."  And I will decrease just suggestions more Apple to upgrade a current driver for the C5180.

  Search Google proposed this solution after a number of other people had the same problem after upgrading them to the Mavericks.

  / Dual rear wheels

  I consider this matter closed.

• WiFi problem after update of lollipop

  Is anyone having problems with their wifi connection after updating to the pacifier. Mine was working fine before the update. A move 35mbps ookla speed test download when connected to my home fibre broadband before the update, but now even hit 1mbps after update. Keep buffering when watching videos. Home broadband Checked speed on pc and getting 34mbps so it's not my Internet problem. Would appreciate ideas. Thanks.Using xperia D6603 z3.

  That's what I'll do, fix the phone with PCC

  PC Companion (CCP)

  Bridge (for Mac)

  Alternatives on how to backup Xperias

  http://talk.sonymobile.com/thread/36355

  and uninstall any antivirus > check again.

• Latitude E5520 Audio problems after upgrade to win 10

  I have audio problems after upgrade to win 10 64-bit.

  Dell Latitude E5520 IDT 92HDxxx HD Audio
  Hardware ID:
  HDAUDIO\FUNC_01 & VEN_111D & DEV_76E7 & SUBSYS_1028049A & REV_1001
  HDAUDIO\FUNC_01 & VEN_111D & DEV_76E7 & SUBSYS_1028049A

  (1) if I use the built-in driver to Win 10 ("high definition Audio Device") I hear speakers/headphones and switching between the speakers and the works of helmet very well but my laptop computer microphone does not work ("not connected").

  (2) if I use the latest Dell driver (IDT 92HDxxx HD Audio Driver) I hear initially via speakers, but as soon as I plug in headphones I can't switch back to the speakers (i.e. switching between the speakers and the headphones does not work) and my laptop computer microphone works.

  I would be happy to provide more information and help to debug.

  To a Microsoft Community Forum, I received the following reply from Rob Brown - Microsoft MVP:

  *************************************************************************
  Hello
  AS OEM Dell is responsible for the good operation of the equipment both
  and Windows. Check their documentation online with Dell Support, and
  drivers and ask questions in the forums about known problems. Make sure that you are
  Run the latest version of the BIOS, chipset and drivers.
  I hope this helps.
  *************************************************************************

  I understand that the Latitude E5520 does not appear on the Dell "Computers tested for upgrade to Windows 10" list... However I was hoping maybe Dell could find in the goodness of their hearts to a updated driver IDT 92HDxxx... pretty please?

  Thank you
  John D.

  johnsdagg

  AS OEM Dell is responsible for the good operation of the equipment both
  and Windows.

  Hi, John. It's quite nervous of a member of the MS forum say that Dell is responsible to operate Windows. It wasn't Dell but MS who claims that Win10 has most of the necessary drivers and if not then the drivers Win7 and Win8.1 would work.

  johnsdagg

  I was hoping that maybe Dell could find in the goodness of their hearts to a updated driver IDT 92HDxxx... pretty please?

  I doubt that it is possible for two reasons. Dell went from IDT Realtek as the audio seller so probably not more a a contract with IDT, if IDT even exist anymore. A year ago IDT was acquired by another company. I do not know its current status, but it is sure that the acquiring company will not be upgrading old software IDT. Reference Dell itself does not write the audio drivers. Even when IDT was the seller I believe that Win7 drivers are the final versions - no version 8 or 8.1 I think.

  johnsdagg

  If I use the built-in driver to Win 10 ("high definition Audio Device") I hear speakers/headphones and switching between the speakers and the works of helmet very well but my laptop computer microphone does not work ("not connected").

  The native Windows audio driver can't stand struggling external mic. It is a MS 'known problem '. MS must implement a decision-making support, but there is no indication that it will be. Meanwhile, you have two workaround solutions. You can switch backwards between the natives and the IDT drivers. At some point Win10 could leave the IDT driver works correctly. Or get an outlet cheap usb audio to the microphone. Struggling running out-audio driver usb Windows native usb and so dependent no driver IDT.

• do not start cc2015 after upgrading Windows 10

  Do not start CC2015 after upgrading Windows 10!

  What can I do?

  A time CC2015 open and that thr program stop and closed.

  Can I read a text at the present time it is not possible.

  What can I do?

  Best regards

  Sandte

  Hi Brucgovn, thanks for the answer! Just sorted and came here to update the post.

  My method is similar, I just do the following:

  1. Go to C:\Program Files (x 86) \Adobe\Adobe Creative Cloud\CoreSyncExtension (this was the only file on the left, all others had been removed from the CreativeCloudCleaner use of the Adobe Creative Cloud cleaning tool to solve installation problems running
  2. I came across the problem trying to remove, so used Unlocker (Download Unlocker 1.9.2 - FileHippo.com) to unlock. Then deleted. It's explorer.exe using the process, which I think caused questions... the process is using the file
  3. Reinstalled and everything seems to work.

• Mac Book (end 2008) not dΘmarre after upgrading to El Capitan 2016 (1511.3.1)

  Mac Book (end 2008) not dΘmarre after upgrading to El Capitan 2016 (1511.3.1) in order to prepare for Sierra

  I tried safe mode > disk utility, which took a lot of time and the disc seems to be OK.

  Extensions have nucleuses, almost all these .kext, but I'm not able to get rid of them.

  -What do you mean by? "Extensions have nucleuses, almost all these .kext, but I'm not able to get rid of them."?

  Did you delete anything?

  -The Mac can't you start mode (boot with the SHIFT key) safe?

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  https://support.Apple.com/en-us/HT201295

  Subject of memory NVRAM and PRAM

  https://support.Apple.com/en-us/HT204063

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  https://support.Apple.com/en-us/HT201262

  -Start to recovery and repair the startup disk

  OS X: on OS X Recovery - Apple Support

  https://support.Apple.com/en-us/HT201314

  -If it is repairable reinstall the OSX

  How to reinstall OS X on your Mac - Apple Support

  https://support.Apple.com/en-us/HT204904

  -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.

  Format the boot disk and then do a fresh install of Mac OS x