spa 112 with firmware 1.0.2 update (006)

Similar Questions

• SPA112 firmware 1.0.1 update 22 to something else...

  When I go in the "Administration" tab, there are only options web change 80 or 443.

  No options on the left for the firmware, or anywhere else in the GUI.

  PLEASE HELP ASAP!

  Scott parks

  Read:

  • Don't miss features in firmware 1.02 in SPA112 that is no possible FW - ug?
  • spa 112 with firmware 1.0.2 update (006)
  • SPA112 firmware upgrade to 1.0.1 to 1.2.1 kills the SPA

• Stream SPA 112 unsuccessful T38 fax call scenario

  Hello

  I will try to explain the situation better than I can.

  A fax device is connected to the port of SPA 112 phone (Firmware Version: 1.3.5 (004_XU001) Sep 16 2014). ATA a T38 support is enabled and a Terminal gateway in this case. A voip account is configured and registered to a provider that supports T38 fax relay Protocol.

  Another fax device is connected to the originating gateway (in this case Patton Smartnode gateway analog) and another voip account is saved in the same provider. T.38 support is intentionally disabled on the originating gateway.

  I expect the following call flow:

  -Endpoint gateway answers the call (G711)

  -Gateway endpoint offers T38 when a fax signal is detected

  -originating gateway rejects the offer t38 (disabled on the device)

  -call is reinvited to G711

  If you look at debugging (zipped attachment, OCAP), seems that the appeal is made to G711, but there is no the SPA112 RTP stream after the G711.

  Any ideas on that?

  ARO

  Sebastian

  P. S.

  To explain the IP addresses used in the trace:

  10.128.3.1 - sip proxy

  10.128.3.4 - media proxy

  10.200.0.17 - originally gateway

  10.200.0.253 - destination gateway (SPA)

  I would like to analyze the captured file and comment on the most important steps. Let go.

  I see two sessions:

  A: 10.200.0.17-> 10.128.3.1	B: 10.128.3.1-> 10.200.0.253
  -> INVITE (with SDP, aLaw, media, 10.200.0.17, sendrecv) <-180 ringing="" (with="" sdp,="" alaw,="" media="" 10.128.3.1,="">	-> INVITE (with SDP, aLaw, media, 10.200.0.17, sendrecv) <- ringing="" (no="">

  The session is now is being "call setup" with installation accounting preliminary call audio ringtones, media 10.200.0.17,10.128.3.1 aloi, bidirectional (sendrecv).

  The session B is now in the phase "system call", no preliminary audio, call progress announced by SIP itself message

  A: 10.200.0.17-> 10.128.3.1	B: 10.128.3.1-> 10.200.0.253
  <- ok="" (with="" sdp,="" alaw,media="" 10.128.3.4,=""> <>	<- ok="" (with="" sdp,="" alaw,media="" 10.200.0.253,=""> -> ACK

  The session is now in phase 'call connected' with 10.200.0.17,10.128.3.4 audio quality, bidirectional (sendrecv).

  The session B is now in phase 'call connected' with 10.200.0.17,10.200.0.253 audio quality, bidirectional (sendrecv).

  Two RTP stream can be seen in the capture file

  1: leave the package 125 & 126 (seq. 4911) 10.200.0.17-> 10.128.3.4-> 10.200.0.253

  2: from the package 129 & 130 (seq. 210) 10.200.0.253-> 10.128.3.4-> 10.200.0.17

  NMC is passed through them and was detected by the endpoint device. So invite:

  A: 10.200.0.17-> 10.128.3.1	B: 10.128.3.1-> 10.200.0.253
  <- invite="" (with="" sdp,="" t.38,media=""> -> 488 not acceptable here	<- invite="" (with="" sdp,="" t.38,="" media=""> -> OK (with SDP, T.38. Media 10.128.3.4)

  T.38 was so successfully (re) - negotiated on session B as sip proxy approved the T.38. Remain sitting A in the former State (e.g. aLaw audio) from peripheral transition rejected T.38.

  Note that proxy media receive the 10.200.0.253 T.38 returns one as-is to 10.200.0.17 despite the existence is not T.38 negotiated here. Also, use packets received 10.200.0.17 are returned as-is from 10.200.0.253 (they are interpreted as T.38 packets).

  It's a little unfortunate behavior. Media proxy should recode media of the Protocol on the left side is not the same as the Protocol on the right side. Proxy SIP should not approve the change of Protocol unless it knows that the proxy media can handle them. On an ideal world, the SIP proxy should not OK T.38/reINVITE to 10.20.0.253, unless he received 10.200.0.17 OK. As a principal is not willing to talk to T.38 and media proxy cannot translate aloi<->T.38 termination invitations must be rejected.

  Well, we do not live in the perfect word and invitations request has been approved. Now, the SIP proxy know proxy media cannot handle the current configuration, then it starts attempt to return the two session at aloi (despite the A session is aLaw already):

  A: 10.200.0.17-> 10.128.3.1	B: 10.128.3.1-> 10.200.0.253
  <- invite="" (with="" sdp,="" alaw,="" media=""> -> OK (with SDP, aLaw. Media 10.200.0.17)	-> INVITE (with SDP, aLaw, 10.128.3.4 media) <- ok="" (with="" sdp,="" alaw.="" media="">

  The two sessions should be now in mode aloi. Unfortunately, despite the 10.200.0.253 received the passage to the quality he continue to use T.38.

  Conclusion:

  It seems that you hit the bug in the firmware. SPA112 must be:

  R: rejection invite T.38 to genuine, if she is unable to do it properly

  or

  B: do it right

  Moreover, in the case of 'A', the SIP proxy can nothing but complete two call legs. Aloi-> transition T.38 premature OK (as I described above) make incompatible with devices that are unable to return for T.38 to sound crude.

  What is now? You can turn in level 3 syslog and debug (voice-> System tab) and catch them. It can reveal more about the issue. But I don't know if it can reveal something that allow us to solve the problem. But you need the newspaper if you decide to report the bug to Cisco SMB TAC.

  You can report the bug in the firmware to SMB TAC even if you have no support agreement.

  Despite you have the contract assistance or not, do not put so much hope that Cisco will help you. And zero chance it will not solve the problem within a reasonable time.

• expansion card MAX capacity micro SD for Sansa e280v2 with firmware 03.01.14

  You just buy Sansa e280v2 with firmware 03.01.14 and try to buy the expansion micro SD card. Found all kinds of answers here on the forum of "anything over 2 GB will work" to "up to 32 GB is OK". So, that is it 2 or 32? Moreover, makes card manufacturer questions? What is important to search the map?

  I'll take the class 6 to off the mark on the class name brand 4 If the prices are the same.  Check the small print, too.  In particular, look for the actual reading and writing speeds listed for cards, if this information is available.  If the seller does not list a lot of detailed information, try the manufacturer's website.  I think that the writing speed is more important than speed reading, as it will be when writing files on the card are you more likely to get impatient waiting for the transfer at the end.

  If I were you I would go ahead and update to firmware 3.01.16, too.  It could have been a related bug fixes SD card.

• SPA 112 - make calls over WIFI between the lines?

  Dear community

  You just bought a SPA 112 which seems to work very well, except for one thing:

  We do not seem to place calls between them the two lines (long cable between two buildings).

  It sounds but is silent and hang up after making a call and end up on the other side. Any chance of a hint?

  Also curious to know if I need to put something specific for use in Sweden? Seems to work very well, but still.

  Do I edit something else? The dial plan?

  Thanks much for any help!

  Jan A.

  1. What is the long cable? What is the cable type (disclose AWG or diameter).

  2. turn on the syslog & debug (highest level) and catch them. It can help to analyze the issue.

   if I need to set something specific for use in Sweden

  According to your wishes. Your username cannot be content with US progress tones or ring US. You can configure some more appropriate for the Sweden , if you wish. Ring voltage waveform, and frequency of the ring should be configured according to your needs of end-phone. Plan of the PBX the SPA112 is saved as well as the requirement of the user of numbering Plan numbering must follow. There is nothing like "a suitable configuration requirements" plan of numbering - even for a given country, including the Sweden.

• SPA 112 Port Sip does not change

  Good day, there is a problem with spa 112. I want to use the different sip as 23405 port, I have change in web graphical interface under SIP PORT is aplied but really no, spa 112 continue to connect on port 5060? y at - it any resolution to this problem? version is 1.4.0

  Peripheral SPA are supported in the SMB community, you might want to settle this.

• Asslam o aliakum. I have a problem with itunes 12.3.2 it is not downloaded the 10 windows and when I connect m iphone with itunes and want to update to 9.2 says please download itunes new version for ios 9.2... help me with this... How to solve this probl

  Asslam o aliakum. I have a problem with itunes 12.3.2 it is not downloaded the 10 windows and when I connect m iphone with itunes and want to update to 9.2 says please download itunes new version for ios 9.2... help me with this... How to solve this problem.

  Greetings Dani56777,

  Thank you for using communities Support from Apple!

  I understand that you run Windows 10 and you must update iTunes to the latest version so that your iPhone will be recognized when connected. I do not know if you receive an error when you try to update iTunes or not.

  If you need information on how to update iTunes, please follow the instructions in the following link.

  Download the latest version of iTunes for Windows - Apple Support

  If you receive an error or alert, you can consider removing iTunes and all of its associated components and then reinstalling fresh iTunes on your computer. That would give you the latest version of iTunes. If you need execute this process, please follow the steps described in the following article.

  Remove iTunes Control Panel and its associated components

  Use the control panel to uninstall iTunes and software components in the following order:

  1. iTunes
  2. Apple Software Update
  3. Apple Mobile Device Support
  4. Hello
  5. Apple Application Support 32-bit
  6. Apple Application Support 64-bit

  On some systems, iTunes can install two versions of the Apple Application Support. What is expected. If both are present, do not forget to uninstall both versions.

  Do these elements in a different order, uninstall or uninstall only some of them. This could have unintended effects. After you uninstall a component, you may be asked to restart your computer. Wait to restart your computer until you finish remove all components.

  Remove and reinstall iTunes and software for Windows 7 and later versions - Apple Support components

  Have a great day!

• any ideas? Installation failure: Windows failed to install the following update with error 0 x 80070663: update of security for Microsoft Office System 2007 (KB972581). That's what I get away

  Installation failure: Windows failed to install the following update with error 0 x 80070663: update of security for Microsoft Office System 2007 (KB972581).

  
  

  any ideas?

  Suggestion: Try to do a repair of Office 2007 installation, then try the updates (after a reboot).

  How to install and repair 2007 Office features
  http://support.Microsoft.com/kb/924611 TaurArian [MVP] 2005-2010 - Update Services

• I stop my new laptop with Windows 7, install new updates. But now my laptop won't charge. There only dark blue screen. He won't even have to sign on the screen. Someone at - it happen?

  I stop my new laptop with Windows 7, install new updates.  But now my laptop won't charge.  There only dark blue screen.  He won't even have to sign on the screen.  Someone at - it happen?

  Hi ctgreen

  Welcome to the Microsoft Answers site!

  You can try the following and link methods under each method for more information on the same and see if one of them solve the problem.

  Method 1: Start the computer in last good known Configuration

   

  1. Remove all floppy disks, CDs and DVDs from your computer and restart your computer.

  Click the button start , click the arrow next to the button lock , then click on restart.

  1. Do one of the following:

  ·         If your computer has a single operating system installed, press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, you need to try again by waiting until the Windows logon prompt appears, and then stop and restart your computer.

  ·         If your computer has more than one operating system, use the arrow keys to select the operating system you want to start, and then press F8.

  1. In the Advanced Boot Options screen, use the arrow keys to select last good known Configuration and press ENTER.
  2. If your computer has multiple operating systems installed, use the arrow keys to select the operating system that you want to start using the last good known Configuration, and then press ENTER. Windows will then resume starting normally.

  http://Windows.Microsoft.com/en-us/Windows-Vista/using-last-known-good-configuration

  Method 2: Start your computer in Mode safe

   

  1. remove all floppy disks, CDs and DVDs from your computer and restart your computer.

  Click on the Start button , click the arrow next to the lock button , and then click restart.

  2. do one of the following:

  o If your computer has a single operating system installed, press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, you need to try again by waiting until the Windows logon prompt appears, and then stop and restart your computer.

  o If your computer has multiple operating systems, use the arrow keys to select the operating system you want to start in safe mode and press F8.

  3. in the display Advanced Startup Options , use the arrow keys to select the option of safe mode you want and press ENTER. For more information about the options, see Advanced startup options (including safe mode).

  4 log your computer with a user account with administrator rights.

  When your computer is in safe mode, you'll see the words Safe Mode in the corners of the screen. To leave safe mode, restart your computer and let Windows start normally.

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  If you are able to access the desktop in SafeMode I suggest you read the article in the link below for instructions on restoring the system.

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  Concerning

  Varun j: MICROSOFT SUPPORT

  Visit our Microsoft answers feedback Forum

  http://social.answers.Microsoft.com/forums/en-us/answersfeedback/threads/ and tell us what you think.

• Computer stuck with screen reading "Configuration of updates: phase 2 of 3-100% full." Do not turn off your computer. »

  Original title: my computer has been slain with screen reading "Configuration of updates: phase 2 of 3-100% full." Do not turn off your computer. "for a week.  What can I do to get it to progress?

  My computer has been slain with screen reading "Configuration of updates: phase 2 of 3-100% full." Do not turn off your computer. "for a week.  What can I do to get it to progress?

  Hello

  You can try the troubleshooting provided in the link below steps to fix the problem.

  An update is not installed successfully when you try to install the update in Windows Vista and Windows 7

  http://support.Microsoft.com/kb/949358

• Problems with Vista start after the update of Norton.

  I had problems with start-up since Norton updated and re-printing my subscription a few days ago.  Initially, the splash screen would freeze, I'll try to re-start, only to be refrozen.  After several attempts, with different amounts of time in between, I tried to start a 'normal', but are also intended to "launch fix."  Microsoft solution is to go back to "settings" before the new and improved Norton Security has been installed.  "Norton isn't too happy with this solution, warning: your firewall is disabled, you are vulnerable to all viruses known to humanity" and Norton resets security and the volley continues.  At some point, the screen may freeze, and I have to start all over again.  Had my Vista Home premium SP1 and SP2 installed this past year, patches and I have had no problems since, so far.  If anything is not easy? The pearls of wisdom would be greatly appreciated.  The garbage man comes tomorrow, I'm tempted to put my computer out of the trash.  Help. Please, I beg you.

  Hello, Heather,

  Boot safe mode with networking.  Download the following tool and run a full scan to exclude the malware.  If the system is infected, Norton will be compromised and would not be able to detect malware.

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&id=16

  Reboot - still problems with startup?  Uninstall Norton - use the uninstaller to remove all traces.  Restart your system and reinstall the software.

  Norton Removal Tool

  https://www-secure.Symantec.com/Norton-support/JSP/help-solutions.jsp?docid=20080710133834EN&LG=English&CT=United+States&product=home&version=1&PVID=f-home&entsrc=redirect_pubweb

  Once you have completed and reinstalled Norton, test - you still having the problem?  Try the link to clean boot troubleshooting below.

  The best advice I can give you is not no use Norton products.  Use Microsoft Security Essentials, which is freeware.

  Perform a clean boot

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

• Problems with aero after the latest updates

  Hello

  Someone had a problem with the latest Microsoft security updates
  touching the aero desktop theme.

  Since I downloaded the updates my aero as a theme stopped working.
  I did a roll windows back but I still have the same problems.

  The updates are #KB971029 and #KB971029 the
  updates have been downloaded on 03/17/11

  I hope someone can help with this problem.

  All the best

  Philip Davies

  Hello

  OK try to remove these updates to see if that helps. Sometimes manually
  install the updates one at a time will prevent topics such as this one (if the)
  mises_a_jour have been the question).

  Control Panel - Windows Updates - lower left Installed Updates - uninstall or change

  Or

  Remove an update
  http://Windows.Microsoft.com/en-us/Windows-Vista/remove-an-update

  Or

  The problems with the removal of updates
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-removing-updates

  Or

  How to uninstall updates in Windows Vista
  http://www.vista4beginners.com/how-to-uninstall-Windows-Vista-updates

  Disable or hide optional updates on Windows Vista
  http://www.howtogeek.com/HOWTO/Windows-Vista/disable-or-hide-optional-updates-on-Windows-Vista/

  AFTER removal of updates, do a system restore to before
  updates have been applied to the origin. Therefore, affect the total amount of
  updates are deleted.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html
  =======================================================

  If necessary:

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ======================================================

  If necessary try a repair Installation which allows to keep the programs and data however
  redundant backups are always a good idea.

  You can use another DVD that aren't copy protected but you you need to own
  Product key. It must be the same version 32 or 64 BIT Vista OEM. Also the system
  machine to usually sell the cheap disk since you already own Windows. Don't forget to make a
  good backup or 3 (security in redundancy).

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-the-recovery-console

  How to perform a repair for Vista Installation
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  I hope this helps.

• New IPad airprint can't find the Officejet Pro 8500 A909g series with firmware DLM1FN1006BR

  The series Officejet Pro 8500 A909g with firmware DLM1FN1006BR is satisfactory airprint on the new IPad?  If not, is there any difficulty?

  No, your printer is not capable of AirPrint and can not be.  You can try other printing applications, like HP ePrint home & Biz.

• Problems with the display after the update of Windows

  Hi guys,.

  I have not installed or updated all programs on my computer for at least a few weeks, with the exception of Windows Update, so part of MS updates, nothing has changed in recent weeks.

  A few days ago, my computer (HP dm1 laptop computer) screen acted funny - I took a screenshot of what happens and posted here:

  http://DL.dropbox.com/u/1076277/desktop_problem.jpg - basically, the display is all messed up with repetition of lines, etc.

  At first I thought it could be a driver problem, but the drivers are ok and were not being updated - in fact, in addition to the usual updates, the only new was the new update now live.

  I did a system restore (restore a week) and everything seemed normal again - this problem is intermittent, but very frequent, but within a few hours of use, there is no problems - until I run Windows Update, and it all started again...

  Any suggestions as to what might be the cause of the problem and a solution? I don't really have the time now to keep stable each item in the update...

  Thanks for the help.

  Hello

  If you want to study, it will take time but you can find the offending update.

  First update all updates (redundant, uh?).

  Make a note of all of the updates (KB numbers, etc.).

  Restore and install the updates one by one and not simultaneously.

  This way you can find the update 'wrong' and later come to conclusions based on what it is supposed to fix.

  Carlos

• Oh no! There is a problem with your recent payment. Update the details of payment for uninterrupted service.

  Hello

  I get this message:

  
  Oh no! There is a problem with your recent payment. Update payment details for uninterrupted service.

  But I have no idea what the 'problem' and payment information are correct...

  What should I do? It seems impossible to contact any Adobe
  

  Hi liamg9149512,

  I see that the payment issue is now resolved with your account.

  Please let us know if there is anything else, we can help you.