SpeechUI constructor has no public constructor

Similar Questions

• Is it possible to put behind a NAT DMVPN hub? (Speaks has a public IP address)

  I he tried for a few days and couldn't make it work. The schema and configuration is in the attachment.

  Crypto isakmp profile: QM slowed down on both sides.

  Profile of crypto ipsec: NO ipsec profile established on both sides.

  Show ip PNDH (side hub): nothing is saved at all. Empty.

  Any ideas?

  Thank you!

  Difan

  As long as the HUB has a static nat translation it should work, try to set your transformation mode of Transport rather than tunnel on two spokes and hub, close your tunnel on the hub and the spokes and then turn it back on, does make a difference?

• Network sharing - cannot access local share of localhost on public IP - wrong password

  Hello. I have a PC that has a shared folder. This PC (A) a public static IP 192.168.1.1. This (A) PC, I try to access \\192.168.1.1 and it works fine.

  This PC (A) has a public IP 1.2.3.4 (roads of firewall on the router on 192.168.1.1 points). I can access both \\192.168.1.1 and \\1.2.3.4 of any PC on the network. Form (A) PC trying to access \\1.2.3.4 - he asks user name and password. After you have entered the correct user name and password it goes back to the connection with the error box that username or password is incorrect. I tried to enter user name & password of every user on this PC (A). I see that it selects the correct user (because of avatar), but don't always accept password. Of course, the same credentials works fine on any PC on the network. Password sharing out of switching does not work - it is still asking for password. There are Windows 7 Professional installed on PC (A).

  EDIT: I can't access from outside LAN network using \\1.2.3.4. Disable the firewall does not help. I have access to the remote desktop on 1.2.3.4 without problem.

  Hello

  Thank you for visiting Microsoft Community.

  I suggest you to post your query on our Forums TechNet social as this question should be better there.

  Please refer to the reference to the link below to send your request:

  https://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking

  Hope this information helps.

  Thank you.

  Sincerely,

  Ankit Rajput

• A Site to remote access VPN behind the same public IP address

  Got a problem quite stupid.  We have a VPN from Site to Site configured for a new data center, which will be responsible for general traffic management.  In addition, some users need to use use a VPN client to access certain areas.  The firewall at the Office only has a public IP address, so the two will come to the Site to Site VPN for remote access from the same source.

  This seems a problem with legacy Cisco VPN clients because encryption card matches the entry VPN site-to-site, even if they use VPN clients.  A good/simple solution to solve this problem?

  Some newspapers (198.18.85.23) is the address public IP for the office and the tom.jones is the user.  192.168.1.0/24 is the pool of the VPN client.

  January 7, 2014 19:12:52 ASA5515: % 713130-5-ASA: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, transaction mode attribute unhandled received: 5

  January 7, 2014 19:12:52 ASA5515: % 737003-5-ASA: PISG: DHCP not configured, no viable servers found for tunnel-group "Corp-VPN.

  January 7, 2014 19:12:52 ASA5515: % 713119-5-ASA: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, PHASE 1 COMPLETED

  January 7, 2014 19:12:52 ASA5515: % ASA-3-713061: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, IPSec tunnel rejecting: no entry for crypto for proxy card remote proxy 192.168.1.4/255.255.255.255/0/0 local 0.0.0.0/0.0.0.0/0/0 on the interface outside

  January 7, 2014 19:12:52 ASA5515: % ASA-3-713902: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, error QM WSF (P2 struct & 0x00007fff28dab560, mess id 0x37575f3c).

  January 7, 2014 19:12:52 ASA5515: % ASA-3-713902: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, peer table correlator Removing failed, no match!

  January 7, 2014 19:12:52 ASA5515: % 713259-5-ASA: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, Session is be demolished. Reason: political crypto card not found

  January 7, 2014 19:12:52 ASA5515: % ASA-4-113019: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, disconnected Session. Session type: IKEv1, duration: 0 h: 00 m: 02s, xmt bytes: 0, RRs bytes: 0, right: not found card crypto policy

  January 7, 2014 19:12:53 ASA5515: % 713904-5-ASA: IP = 198.18.85.23, encrypted packet received with any HIS correspondent, drop

  Hello

  Don't know if this will work, but you can try the following configuration (with the rest of the VPN configuration)

  list-access CLIENT VPN ip enable any 192.168.1.0 255.255.255.0

  card crypto OUTSIDE_map 4 is the VPN CLIENT address

  card crypto OUTSIDE_map 4 set peer 198.18.85.23

  card crypto OUTSIDE_map 4 set ikev1 transform-set ESP-AES-128-SHA ESP-3DES-SHA

  The idea would be to have the ACL matches the VPN full Tunnel that the Client attempts to establish. (destination "any" from the point of view of the customer, the ASAs view source)

  I tested briefly on my own SAA by connecting from an IP address to which the ASA offers free VPN in L2L. But as I don't have the operational L2L VPN, I can't really verify the VPN L2L at the moment. Thus, certain risks may be involved if you can afford it.

  -Jouni

• Menu start a username like mine and a Public default - is a problem of security and safety?

  I want to secure my PC as much as possible. I had a pirate that I had to pay an expert to check out it. Now, I try to learn more about my PC. When I go to the System Configuration and then tap tools and then look in system information and then expand software environment and click program groups - I see not what follows, and I want to know if the - access Public is correct and what is it? And it is a threat to security?

  My Start Menu has a Public Start Menu name and a user name Public as he looks and a "defect".

  Start a Public programs: programs on the Start Menu
  Public's early Menu\Program\Accessories: Star Menu\Program accessories
  There is a Menu\Programs\Administrator Public: start

  Now; I have mine listed as well and also a 'default', I need to fix this? If I please give me instructions step by step. Thank you

  ' p

  Hello coldtoes10 a welcome to the forum of Microsoft.

  It doesn't matter its content in your menus, but if you want to be sure it's something I can do

  one of the following will improve your security greatly,

  First off get your firewall in bulk to the top ethical hackers are paid to hack to help you improve your security

  Ethical Hacker

  never do anything on an open wy - fy. buy a router, when you configure the network goto this site and create a network password

  http://www.random.org/passwords/

  30 digits should do

  15chiffres of computer passwords, 45 figures to break is almost impossible

  10 digits for all online accounts

  then on the Internet, don't spread your IP instead use Tor navigation Pack your completely anonymous being online

  then read a ton of books on security Internet here are just a couple

  COMPUTER security for Dummies

  Computer security handbook

  If you want to be proud look high-tech in your firewall, Spike

  {note: spike is notorious of very effective malicious code entering your firewall}

  Good luck

• With PUBLIC IP VPN client

  Could Hi someone help me? There is a PC VPN client whose public (without NAT router) IP address, it can connect to the server EZVPN and recive reoutes but traffic is not passing,.

  Yes

  the Transport TCP value on the client side, with the tcp f.i. 10000 port and make sure that the VPN box can talk tcp 10000 more too.

  If a customer has a public ip address, it will be successfully Setup a VPN, but can't access anything via UDP with NAT T.

  If configure you the TCP transport, it will be.

• Outlook does not, Exchange is a virtual machine on my iMac with public IP address

  My iMac is connected to my switch and my switch is connected to my NVG589 of ATT modem.  My iMac draws a DHCP ATT modem and the intellectual property IP is 192.168.1.64.

  I am running VM Fusion on the Mac, version 7.1.3 (3204469) and I've updated for yesterday.

  One of the virtual machines on my iMac is Exchange 2013 and it has a public IP address.

  So, to summarize, my iMac is DHCP with a private class C address and my VM is static in a class A public address.

  Before the update I could open my outlook on my iMac and it connected to my server exchange very well.

  After the update, my vision and my iMac OWA do not work.  My outlook to connect, but it won't draw down of any mail and my own just can't OWA load.

  Exchange and OWA work from any another machine other than the iMac.

  I can't help thinking that it's something in the update that has done this because it worked before the update 7.1.3 (3204469).

  The NIC is auto detection against NAT or bridged and I haven't changed it.

  Can anyone suggest something that I have not tried?

  Thank you

  Cliff

  This has just started tonight.  very strange

• NSO - existing public API? documented?

  We have an account of Fusion CRM, with a Social network as part of it.

  Yes, it is possible to share a CRM object in NSOS (as described in Implementing Oracle 11 g Release 7 (11.1.7) social - integration network), but we want to add more "automatic" functions to it.

  We can try to call scripts Groovy CRM, or perhaps an application hosted on the outside.
  

  
  

  It seems assuggestion OSN has a public RESTful API (see http://dgielis.blogspot.com.au/2012/10/integration-of-oracle-social-network.html), but I can't find referenced to this API.

  It exist at all? Is there documentation? Are no Web Services API?

  Thank you.

  Dmitri Tchikine

  Dmitry-

  We provide an API for working with the Social network of the Oracle to do this custom development you describe.  We make this documentation available to known clients, and I will follow to the top with you directly in the next day with the location you can get it back.

  Best regards

  Josh

• public access to an apex

  Hi, I'm just familiarize themselves with Apex. I want to create an application that has a public access... They just click on a link on our intranet and go directly in the App (it's just a bunch of classic and graphic reports). However he keeps asking the authentication scheme (and I don't want one)
  
  What is the best way to implement?
  Ed

  Hello

  What is your version of the Apex?
  Check if this similar post help
  Page access without asking for password

  Kind regards
  Jari

• Wanted: simple example of the class of data with a signal?

  Been looking for a tutorial on that in the examples and find nothing.  Maybe I missed it?

  I'm looking for an example of simple data class that has a public method to define an observer, similar to this:

  class MyDataClass : QObject // I'm guessing I would subclass QObject
  {
    public:
    int getSomeValue();
  
    signals:
     void setObserver(const QObject* receiver, ...?);
  
    private:
    int m_someValue;
  };
  
  // ...and cpp file with setting the connection
  

  There in this code example?  If this isn't the case, could someone put an example of class?

  I've seen samples in QML, but I'm looking for C++.

  Thank you!

  #include 
  
  class Settings : public QObject
  {
      Q_OBJECT
  public:
      explicit Settings(QObject *parent = 0);
      static Settings *sharedInstance();
  
      QString getTargetIPAddress();
      void setTargetIPAddress(const QString &ipAddress);
  signals:
      void targetIPAddressChanged();
  };
  
  ---
  
  #include 
  
  #include "Settings.h"
  
  const char *targetIPAddressKey = "targetIPAddress";
  
  Settings::Settings(QObject *parent) :
      QObject(parent)
  {
  }
  
  Settings *Settings::sharedInstance()
  {
      static Settings settings;
      return &settings;
  }
  
  QString Settings::getTargetIPAddress()
  {
      QSettings settings;
      QVariant v = settings.value(targetIPAddressKey);
      if (v.isNull())
          return "192.168.0.1";
      return v.toString();
  }
  
  void Settings::setTargetIPAddress(const QString &ipAddress)
  {
      QSettings settings;
      settings.setValue(targetIPAddressKey, QVariant(ipAddress));
      settings.sync();
      emit targetIPAddressChanged();
  }
  
  ---
  
  Some other class:
  
  .h:
  protected slots:
      void targetAddressChanged();
  
  .cpp:
  [...constructor...]
      Settings *settings = Settings::sharedInstance();
      QObject::connect(settings, SIGNAL(targetIPAddressChanged()),
                   this, SLOT(targetAddressChanged()));
      targetAddressChanged(); // for initial setup
  [...]
  
  void UDPClient::targetAddressChanged()
  {
      Settings *settings = Settings::sharedInstance();
      // Do something with settings->getTargetIPAddress()
  }
  

  I hope this will help.

• How do I send a call to voicemail?

  Hi, I am a new BB developer. I have finished and understood the "Hello World" project, and I now move on to what seems to be the mandatory "Rejection of calls" program (where you can specify what calls are allowed to sound).

  I found a good tutorial on the basics of working with the calls and the phone class (net.rim.blackberry.api.phone.Phone): tutorial here

  So far, my code looks like this (Please be gentle, I'm new to Java and did not change the sample code little but more important still, I understand):

  /* * MyPhone.java */package MyPhone;
  
  import net.rim.blackberry.api.phone.*;import net.rim.device.api.system.*;import net.rim.device.api.ui.container.*;import net.rim.device.api.ui.*;import net.rim.device.api.ui.component.*;import net.rim.device.api.util.*;import java.util.*;
  
  public final class MyPhone extends AbstractPhoneListener {
  
    /* Simulate a list of numbers to send to voice mail */    public String[] badNumbers = {"+15555551212","+11234567777"};  
  
    /* My Entry Point */    static public void main(String[] args)  {    MyPhone.registerOnStartup();  }
  
    static private void registerOnStartup()  {    MyPhone phone_handler = new MyPhone();    Phone.addPhoneListener(phone_handler);  }
  
    /* Constructor */  private MyPhone(){}
  
    /* Handles Calls */  private void checkCall(String ehandler, int callid)  {    PhoneCall callInfo = Phone.getCall(callid);
  
      if ( callInfo != null ) {
  
          /* If we have an incoming call, loop         * through all bad numbers, and send         * to voice mail if we found a match.         */
  
          if(ehandler == "callIncoming"){                     for (int j = 0; j < badNumbers.length; j ++) {            System.out.println("Bad number is: " + badNumbers[j]);          }        }
  
         System.out.println("Event Handler: " + ehandler);       System.out.println("Telephone No: "  + callInfo.getDisplayPhoneNumber() );       System.out.println("Elapsed Time: "  + callInfo.getElapsedTime());       System.out.println("Call Status: "   + callInfo.getStatusString());    }  }
  
    // A call has been added to a conference call  public void callAdded(int callId)  { checkCall("callAdded", callId); }
  
    // User answered a call  public void callAnswered(int callId)  { checkCall("callAnswered", callId); }
  
    // Conference call established  public void callConferenceCallEstablished(int callId)  { checkCall("callConferenceCallEstablished", callId); }
  
    // Network indicates a connected event  public void callConnected(int callId)  { checkCall("callConnected", callId); }
  
    // Direct-connect call connected  public void callDirectConnectConnected(int callId)  { checkCall("callDirectConnectConnected", callId); }
  
    // Direct-connect call disconnected  public void callDirectConnectDisconnected(int callId)  { checkCall("callDirectConnectDisconnected", callId); }
  
    // Call disconnected  public void callDisconnected(int callId)  { checkCall("callDisconnected", callId); }
  
    // User ended call  public void callEndedByUser(int callId)  { checkCall("callEndedByUser", callId); }
  
    // Call has been placed on "hold"  public void callHeld(int callId)  { checkCall("callHeld", callId); }
  
    // New call has arrived  public void callIncoming(int callId)  { checkCall("callIncoming", callId); }
  
    // Outbound call initiated by the handheld  public void callInitiated(int callid)  { checkCall("callInitiated", callid); }
  
    // Call removed from a conference call  public void callRemoved(int callId)  { checkCall("callRemoved", callId); }
  
    // Call taken off of "hold"  public void callResumed(int callId)  { checkCall("callResumed", callId); }
  
    // Call is waiting  public void callWaiting(int callid)  { checkCall("callWaiting", callid); }
  
    // Conference call has been terminated  // (all members disconnected)  public void conferenceCallDisconnected(int callId)  { checkCall("conferenceCallDisconnected", callId); }
  
    // Call failed  public void callFailed(int callId, int reason)  {    checkCall("callFailed", callId);
  
    }}
  

  In my loop where I check to see if there is an incoming call, I'll see if it corresponds to a wrong number. If so, I don't want no phone in the same ring, just ignore and go to voicemail.

  My question is, how? I've scoured through the API and do not see anything remotely close to send a call to voicemail.

  Thank you!

  John

  the menu item went into new versions of the OS, typing only injection remains - unless there is another method that the community does not know.

• ... does not support the measure

  Hello
  When I deploy a custom newspaper followed plugin server-side log shows [servername] can't measure.
  
  I have:
  
  # 1 class of measure specified in the AC - plugin.xml. It is inside the server tag. I have only 1 server and no service.
  #2 this class has a public constructor that takes no parameters
  #3 if I comment on the content of the manufacturer that it does not show this message.
  
  Any ideas?
  
  Thank you
  Sylvester

  The file of your builder of does not exist on the server, like this is that what is causing the error?  If so, can you just conditonalize if (new File (name) .exists ()) {...} to avoid the error?

• How to create a class?

  Hey everybody! I'm a flash newbie. can someone tell me how to create a class?

  I guess you know what a class is right there. In case you haven't, a class is essentially an action plan which new objects are instantiated. He describes the State and behavior that objects of the class all share. You can learn more on this topic in detail in wikipedia. Creating a class in flash is rather simpler than in C++ and a bit different since you need not all definitions of prototype. Let's take an example. Create an active 'FLA' with AS3 file and an external ActionScript file (which is a text file with the extension ".as"). In the file AS to place this code:

  package / /package can have a name next to it

  {

  public class MyClass //class definition

  {

  private var nMemberVarValue:Number;

  public void MyClass(nSomeValue:Number) //Constructor

  {

  nMemberVarValue = nSomeValue;

  }

  public function getTheValue (): number function //Member

  {

  Return nMemberVarValue;

  }

  }

  }

  In this example, you have a class named "MyClass" that has a constructor (should be the same name as the class) that accepts a single parameter. It has a public function (accessible method by external objects) "getTheValue" and a variable private "nMemberVarValue" which is encapsulated in the class. Now in the 'FLA' file, place the following code that instantiates an object of your class 'MyClass ':

  import MyClass;

  var cMyInstance:MyClass = new MyClass(1234);

  trace (cMyInstance.getTheValue ());

  You'll see when you run your file with CTRL + ENTER, it will trace the value 1234 in the output window. Best practice is to keep in the classroom through ActionScript (.as) file. 1234 is only an example setting. You don't need a constructor to accept all settings, depends on what you plan to do class.

• Events not captured

  I have a strange behavior with one of my custom events. (my other events are very good).
  
  The event is distributed with this code:
  
  private void handleLoginResult(event:ResultEvent):void {}
  var user: XML = new XML (event.result);
  If (user! = null & & user.userId! = null) {}
  var e:LoginEvent = new LoginEvent (user, 'loginProcessed');
  this.dispatchEvent (e);
  Alert.Show ("send event");
  }
  }
  
  
  I see my alert, every thing is good up to this point. My metadata looks good, here's the list:
  
  < mx:Metadata >
  [Event (name = "loginProcessed", type = "events. LoginEvent")]
  < / mx:Metadata >
  
  
  I have a LoginEvent.as class in the package "events". This is the standard, extends from flash.events.Event, has a public constructor:
  public void LoginEvent (user: XML, type: String, bubbles: Boolean = false)
  
  I have in my main application, create a custom panel and declare the listener:
  < v2:Login title = "Login" id = "loginPanel" loginProcessed = "Alert.show ('debug')" / > "
  
  Now, when the event is raised I do not see the alert "debug". Can someone help me understand why this is?

  dimival, whoever you are, you are generous. The manufacturer had a superclass appellant of the problem. I am listing below. The compiler does not care to catch my error, but you did!

  
  package events
  {
  import flash.events.Event;

  SerializableAttribute public class LoginEvent extends Event {}

  public var user: XML;

  public void LoginEvent (user: XML, type: String, bubbles: Boolean = false) {}
  Super (user, type, bubbles);
  This.User = user;
  }
  Public Overrides function clone (): Event {}
  return of new LoginEvent (user, type, bubbles);
  }
  }
  }

• Export the SSL keys problem

  I am trying to export ssl certificates & keys of Keychain Access on our server (5.1.7) for purposes of future recovery disaster. I have multiple ssl certificates installed and most is very well, but one in particular has 4 public keys and 5 private keys. I don't know what keys to export! I tried to export several public keys and compared; they are all different. I don't know how to determine which is correct. As you can see below, none has yet a timestamp.

  

  Any ideas? Alternatively, is there another way I can go about this?

  There is a reason any you do not export only each of them? They are very small files and if you guess wrong and one to exclude your claim won't go well.

  C.