SpeedStep technology is available in Satellite L300-11 q

Hello!

Is option SpeedStep included in model Toshiba Satellite L300-11 q?

Thank you!

Hello

I think that this device does not support the Intel SpeedStep technology.

Why? It of very simple to explain this;
If I m not wrong not the Satellite L300-11 q was equipped with the Intel Celeron processor 550 Merom 2.00 GHz and this processor does not support the SpeedStep.

Best regards

Tags: Toshiba

Similar Questions

  • Cannot connect by Satellite L300-1BW to wireless technology

    My Satellite L300-1BW has recently ceased to connect the my Wi - Fi.

    It shows that wireless networks are available, I can see my secure network and there is no red cross through the icon but when I click on IE, it only says: unable to connect.

    I tried with 2 of my friends houses on their connections without wire (previously connected) and it just does the same thing.
    I can see all the networks concerned, but it won't take me actually to my homepage.

    I do not understand why it has just stopped working - drives my lan are up-to-date. Help..!

    Hello

    You can see the WLan, which means that the WiFi is enabled correctly.
    But have you used the good encryption and encryption password in order to connect to the WLan router?

    Please check this!

    Please also check the firewall settings!

  • Stereo mix is available for the L300 Satellite?

    Hello

    I've looked everywhere to see if I can learn how to get the stereo mix for the L300 and I can't seem to find something for her.
    Stereo mix is available with the L300 satellite?
    I can get it and if I can how?

    Hello

    What piece of sound card do you have?
    Is - this audio chip Conexant?

    To my knowledge the chip audio Conexant does not support that I have a laptop with Conexant audio chip and the other audio laptop chip Realtek.
    Laptop computer with Conexant sound card does not support the stereo mix. The Realtek made.

  • How to enable Intel Speedstep on Satellite L300-1BD

    Hello

    Today, I bought the Toshiba L300 - 1BD that Vista is preinstalled.

    To improve my batterylife, I changed vista to 'classic design' and the option of energy "energy saving".
    Although it does not use the Intel Speedstep technology.

    When I run the utility: CPU - Z, it shows that the speed of the CPU is at 2000 Mhz. normally, when the CPU is idle, it must change the multiplier to low, screaming result in approximately 1000 mhz. This can save a lot of battery!

    Does anyone know why it does not work, or how to make it work?

    Thanx and Greetz from Germany!

    Are you sure that the processor supports the Intel speed step technology?

    I googled a little bit and it seems that this unit was equipped with the 667 MHZ Celeron 575 Merom (2.00 GHz) CPU

    And I m 100% sure this CPU * DOESN T * support speed stage.

  • Satellite L300: Where to find a free software available for HD-DVD playback

    I have a toshiba satellite L300 and a drive of xbox 360 hd - dvd.
    I can't the Toshiba hd dvd player software without having to pay as I initially normal dvd play software?
    If not does anyone know if there is a freeware software for hd - dvd playback

    Thank you

    As far as I know, HD-DVD player was offered for equipped laptops of HD-DVD player and your computer laptop doesn t have it so what you can try is Google around a little bit.

    By the way: you want to watch movies HD-DVD on your laptop or what?

  • Satellite L300 - cannot install Microsoft updates after replacing HARD drive

    I am repairing a Satellite L300, which had a dead HARD drive. I replaced death 160 GB of HDD with a 500 GB WD, then used the recovery disks to install Windows Vista SP1 at the exit of the State of the box.

    Now, Windows update does not work, won't install autonomous not of Vista SP2 I downloaded, MS Security Essentials moved there also.
    Then I borrowed a 160 GB of work and went through the same process and everything works fine.

    To make it work with a 160 GB HARD drive, but not a 500 GB HARD drive. Why?

    > ... Standalone Vista SP2 I downloaded will not be installed
    Usually after installing recovery image, you have just to connect laptop to internet and after a short period of time, you will get messages about available Windows updates. Just install the offered updates process automatic Waterer and install important updates only.

    Let the system to install all the updates and don t force the installation of some own downloaded stuff.
    Last month I've updated HARD drive (320 GB I think) and installed Win7 on friends L300 and I didn't noticed any problem here.

  • Satellite L300 - upgrade from Vista Home Basic to Home Premium issues

    Hi all

    I recently got a Satellite L300 with a basic family OEM of Vista Edition version.
    I have a copy of Windows Vista: drive home edition Premium (upgrade) and decided to use it on the laptop.

    I put the disc in and followed the steps but the upgrade option is removed... It is if I use the product key provided with the disc or not.
    The laptop comes with Service Pack 1 is already installed and the drive I have is released in stores before Service Pack 1.

    My main question is really how can I get my drive to upgrade my version of Vista. I tried the Google search, this Web site, Microsoft Web site and I get the same answer.

    Basically, go into options and upgrade Express. They're all for me to buy from Microsoft that would be kinda useless as I already have a copy.
    I read something to a site that said my drive would have to have service pack disk and I've seen a site with some sort of disk editing program for Vista but I am not too keen to use it and the 'how' was not very easy to understand.

    Also, I am not too keen on appellant Toshiba or Microsoft on surcharge numbers to get something, I already bought and paid for and should be as simple as a few steps.

    Anyway hope someone can help as I really want to upgrade.

    Hello

    I understand and it is really annoying, but what to do now? the fact is that Toshiba has offered this book with some version of Vista. This version should be updated to better Microsoft security and the most recent available. Because of this Toshiba supply with the last option of SP1.

    So now, you try to install proposed update it there long and probably offered before SP1 was on the market. I understand your point of view but, in my opinion, has nothing to do with Toshiba now, and you should try to find the solution with Microsoft. For example you can also get info from http://support.microsoft.com/kb/930733

    Clean Vista Home Premium can be installed without any problem. All the drivers, tools, and utilities are downloadable on Toshiba support & download page.

  • Satellite L300 - MSKLC1.4 keyboard layout creator does not work properly

    Hello

    I installed the MS MSKLC 1.4 tool. on Toshiba Satellite L300 and Vista32. This tool is to generate a clean keyboard layout.

    I wanted to implement Gujarati signs for a friend. To do this, we put signs and letters on three 'levels' in this keyboard layout:

    1 Standart "a, b".
    2. pass the speeds as "A B"
    3 Altgr + key

    The first two levels with letters not run very well, but the last of them.

    We have tested in Open Office 3.1 and MS Works Word. The two programs do not accept Altgr + key letter.
    Open Office has no special function keys altgr +.

    In an editor that comes with MSKLC 1.4, level 3 also works very well. NO problem here!

    How this can happen? What should I do?

    Jens

    MSKLC 1.4. is available:
    http://www.Microsoft.com/downloads/details.aspx?FamilyId=8be579aa-780D-4253-9e0a-e17e51db2223&displaylang=en#overview

    > On a German-Toshiba A50 with XP.
    > THREE States appear Gujarati letters.

    To be honest I never tried to MSKLC1.4 keyboard layout creator but I n t think that it s a question of Toshiba.
    I think that it s related to the UK keyboard layout because he of working with available German (as you suggested).

    My personal suggestion could change the layout of the UK keyboard for the German language in Control Panel-> regional options & language control

    Check if this help

  • Need help with the recovery of the System Satellite L300-149

    Hello

    We have a Satellite L300-149.
    Was running really slowly then wanted to reset it to factory settings.

    Doesn't the "press F12 during startup, insert the disk in" etc etc BUT have a horrible feeling that I put a disc to which belonged in fact to a different Toshiba, we used to use a U300.
    'Give' was that the manual for the U300 is now on the desktop on the Satellite :-/

    I hope that this would not be a major problem BUT the F8 key is gone now it's impossible to connect to the internet.

    I looked online and read that the L300 sometimes doesn't come with a disc that the info is kept on a separate part of the disk hard hope so I could reset it back to settings to factory again but when I click on F2 on start up and go to the option to restore it, noting happens.

    Can someone please help?

    Hello

    Forget HARD drive recovery now
    You have recovered the system using another disc and it has been removed and the HARD recovery disk image files. If this option is NOT possible!

    You reason that the L300 and all other laptop does not come with recovery discs.
    The recovery disk must be created using the recovery disk Creator called preinstalled software. But it is also NOT possible because you deleted the preinstalled system and the files that are needed for this recovery disk are no longer available!

    But if everything is working properly except the WLan FN + F8 key, then I recommend you only install the Wlan driver. I think that the key does not work because the right WLan driver is not installed.

    I think that the Satellite L300-149 supports the smart WiFi Realtek RTL8187B.
    Then install the right driver Wlan you can find here:
    http://APS.toshiba-tro.de/WLAN/?page=downloads

  • Re: Satellite L300-255: how to increase the shared memory graphic

    Hello

    My laptop is Satellite L300-255. I have improved it's ram to 4 GB. I want to increase the graphics card 1 340 MB. In the specifications of the laptop, he said that the graphics card can increase if the Ram has increased to 3 GB

    Thank you

    Post edited by: PauPau

    Hello

    Shared graphics memory is controlled by GPU driver. You cannot add or edit it manually.

    More depends on the Windows OS you use, because the 32-bit system can manage max 3.2 GB of system memory.

    For example:

    * (32 bit OS) *.
    System memory: 2GB | 4 GB
    Dedicated video memory: 128 MB | 128 MB
    Shared system memory: 702MB | 1214 MB
    TOTAL available graphics memory: 830MB | 1342 MB

    * (64 bit OS) *.
    System memory: 2GB | 4 GB
    Dedicated video memory: 128 MB | 128 MB
    Shared system memory: 702MB | 1631 MB
    TOTAL available graphics memory: 830MB | 1759 MB

    Hope I could help you

  • Re: Drivers Win XP for Satellite L300-PSLB8A - 0d 5004

    Hello...

    Recently I did something stupid... to install windows xp on a windows vista computer...

    Anyway, Ive a messed up but now on this windows xp Toshiba Satellite L300-PSLB8A - 5004 0d I'm missing some drivers... I was wondering if someone could give me the correct driver links so I could download them please...

    the following drivers are missing:

    _ * ethernet controller: * _ PCI\VEN_10EC & DEV_8136 & SUBSYS_FF661179 & REV_02\4 & 38F101EE & 0 & 00E0
    _ * ethernet controller: * _ PCI\VEN_168C & DEV_001C & SUBSYS_7128144F & REV_01\4 & 318470AD & 0 & 00E1
    _ * device on high definition audio bus modem: * HDAUDIO\FUNC_02 & VEN_11C1 & DEV_1040 & SUB _ SYS_11790001 & REV_1002\4 & 1760F043 & 0 & 0101
    _ * Video controller: * _ PCI VEN_8086 & DEV_2A43 & SUBSYS_FF671179 & REV_07\3 & B1BFB68 & 0 & 11
    _ * Video controller (VGA compatible): * _ PCI VEN_8086 & DEV_2A43 & SUBSYS_FF671179 & REV_07\3 & B1BFB68 & 0 & 10

    When I go into run and type msinfo32 then expand the items and check problems for ethernet controllers it says that this device is not configured correctly and for the res, it tells the drivers for this device are not installed. There is also 1 * not AVAILABLE * uninstalled car door a PNP ID number if someone wants.

    Please can anyone help... I urgently need these drivers...

    This will help you to identify the device and to get good drivers:
    [How to identify an unknown device (e.g. LAN wireless module)? | http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=78]

    But at first glance, it seems that you have need of a driver for the graphics card, modem, LAN and WLan driver.

  • How to enable virtualization on Satellite L300-1DN?

    Hello
    I would like to know how to enable virtualization on Satellite L300 1DN please?
    Thanks in advance

    Hello

    General virtualization is not available on all computers laptops because it s based on the material and it must be supported on the CPU.
    On many models with processor supports virtualization, this option is added in the BIOS. Sorry, but if this option is not available in the BIOS settings nothing you can do about it.

  • Satellite L300 - after what Win8 load DVD drive does not work

    I've just loaded Windows 8 on my Satellite L300. The DVD no longer works with a 39 error message, it indicates that the driver is corrupted. Also attached external DVD is not recognized. I can't find a driver to reload.

    All of the suggestions.
    Concerning

    See this article:
    http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/bulletinDetail.jsp?PF=true&soID=3516888

    If the TOSHIBA Recovery Media Creator or TOSHIBA Disc Creator is installed on the HARD disk, there could be a problem between Win 8 and software mentioned
    So to uninstall these tools, then restart your PC using the power--> reboot option in Windows 8. Your CD/DVD should be available now.

  • Satellite L300 - 1 8 - Microsoft Works Suite has stopped working

    Hiya,

    first I will say that I am only on my 2nd computer so im not exactly a brainbox on them.
    I have a Satellite L300 - 1 8 with microsoft vista home premium 32 bit.

    I only had this laptop for less than 2 months today, when I was with microsoft works suite, word processor he suddenly stopped, I rebooted a document she had auto saved and then closed.
    When I tried to open another document empty it let me, but he wouldn't let me stick to what I needed.
    Now, I can't open anything in microsoft works and if I try I get the message:
    + ' A PROBLEM CAUSED THE PROGRAM TO STOP WORKING CORRECTLY. " WINDOWS WILL CLOSE THE PROGRAM AND NOTIFY YOU IF A SOLUTION IS AVAILABLE. +

    What is - this and why the habit he work?
    I him have not used much in fact I think it's maybe the first time. I was on the site of microsoft and its Greek to me, in any case the bit I understand he said "If your windows is preinstalled go to Toshiba" or words to that effect.

    I've been on the Toshiba site and it's all Greeks too. I don't understand all this and I can't seem to find any assistance on their part, the only help I can find is this site with everything what you smart people on the resolution of our problems to us.
    Then I can help you, in simple language please.

    Thank you. Julia :D

    Hello

    It is a simple generic error message that you will always see when the programs or applications crash.

    Something was wrong, but I can't tell what's wrong with your MS works.
    If you want the event viewer for errors, but to be honest, you can check this will not help you much if you're not computer.

    I gogoled a little and some people brought on the same error in MS Word, but like I said above; This is a generic error message.

    However, the people have this problem than by the new installation of MS Works.
    I don't know if you received a MS Works Mr. disc if so, remove/uninstall the MS Works the system first, reboot the laptop and use the MS Works drive for new installation.

  • Satellite L300 - losing wireless connection

    Hello

    (loss of wireless connection)
    I'm not technical interest in this area, but rather disturbing and it is worse, I thought I would post this question to see if anyone new what it was.

    This laptop is new (Toshiba Satellite L300-1BV) Home premium 32-bit.
    This happens a lot and it can be "A PAIN" and really fustrating, I suddenly lost my wireless connection and I can't view available wireless networks to try to connect again, especially since I have to restart the laptop and everthing is back to normal.

    He can be nice days then all of a sudden, this will happen, but why am I not pick up all other available networks.

    Network provider... BT YAHOO TO BROADBAND
    Router... BT HOMEHUB 2.0
    network card... REALTEK RTL8187B WIRELESS 802. 11B / G 54MBPS USB 2.0 NETWORK ADAPT.

    I know for interference and have done everthing possible to avoid this...

    Hello

    -Update the display driver
    -Update the BIOS
    -Disable the Save feature in WLAN power Windows power management
    -Check the WLAN standard (for example: 802.11 g or Draft N)

    In addition, you should read the hundreds of threads here in the forum on the problems of WIFI. It might be very useful! ;)

Maybe you are looking for