SSL & amp; Problem FLASH, IE & amp; IIS, caching

Similar Questions

• Monitor the problem flashing on the reactivation of the computer.

  Monitor the problem flashing on the reactivation of the computer.

  I have a new HP laptop G60 - 243 CL of Costco and a new HP W2207h monitor. The screen flashes when the laptop wakes fashion "sleep" with the HDMI cable connected. It works very well with the VGA cable. Any assistance in finding the cause would be much appreciated. Here is my hardware spes and a newspaper detailed observations.

  Thanks in advance,

  Paul

  --

  HP W2207h monitor

  680 x 1050 hz @60

  Laptop:

  HP G60 - 243 CL

  AMD Turion X 2 RM - 72 2.1 GHz

  3 GB RAM DDR2

  320 GB SATA, 5400 RPM HARD DRIVE,

  NVIDIA GeForce 8200 M G, with up to 1407 MB total graphics memory (shared).

  16 "16:9 1366 x 768 display

  Drive x drive LightScribe 8 with support double layer
  HDMI

  Here is my log.

  25/01/09

  1 unpack the monitor. With mobile connection cables on: HDMI, USB, power Turn on the monitor. It flashes. Black for about 2 seconds, then the light for a split second, repeat, ongoing. Turn off monitor, the driver of the CD W2207h monitor, restart. Monitor works normally.

  The monitor HP w2207h Readme says driver using driver Nvidia 10.65 or later version.

  The Control Panel on the computer laptop G60, NVIDIA GeForce 8200 M g: Device driver 7.15.11.7614, 11/07/2008 (this is the latest driver from the HP support page. See on 27-01-08 below).

  Install W2207h Monitor driver CD and restart the computer. Control Panel, device, Manager I see two monitors, the two "monitor PNP generic", first Hardware ID "MONITOR\HWP26A8", the second "MONITOR\SEC314C", both with the 6.0.6001.1840 driver (longhortn_rtm.080118 - 1840), I wonder if, maybe, the pilot did not.

  2 put the laptop into sleep mode. Wake the portable computer and monitor flashes market, as described in (1). Image appears normally while the monitor is turned on for fraction of a second intervals. If reboot laptop, follow the work properly.

  Occasionally, flashing monitor heal without rebooting. Out of about 10-15 tent: once the monitor began to function properly while the computer shuts down. Once the monitor was OK on the reactivation of the laptop. Once, while the screen flashes, I removed the USB cable and the monitor started working. None of this is repeatable.

  3 removed the HDMI cable and started using the VGA cable and an audio cable. No more flashing on the reactivation of the computer. Very repeatable. About 7 7 times.

  01/26/09

  Control Panel, two monitors, Device Manager, the two "monitor PNP generic," first of all we have the Hardware ID "MONITOR\HWP26A8", second is "MONITOR\SEC314C", both with the 6.0.6001.1840 driver (longhortn_rtm.080118 - 1840), I wonder if, maybe, the pilot did not.

  27/01/08

  Download NVIDIA drivers

  Downloaded from Nvidia support: Version 179,28, 2008-12-18, 179.28_notebook_winvista_32bit_beta.exe Beta (attention: are not supported by the laptop to the manufacturer.)

  HP support: Version 7.15.11.7614 has, 2008-09-08, sp40385.exe (same version that is installed.

  Version of the driver installed is the same that the one on HP support site, so did not not update driver.

  w2207h monitor download driver

  Download and install A Rev 2.0, 4.0.100.1189, 2008-10-16

  Version of the file now reads 6.0.6001.18000 (longhorn_rtm.080118 - 1840), I think it's the same as the driver already installed.

  Flashing problem is unchanged.

  –

  end

  It was the monitor! I brought my laptop and a HDMI cable at Staples where I bought the monitor and tried on the w2207h on set. It has worked well. Took the phone in and out of fashion 'sleep' several times. I'm in the store week return policy 2 stables will replace it. The seller was very accomodating to let me try different monitors with HDMI and VGA cables and my laptop while I was there. I even brought in a large piece of cardboard to protect the ceiling :).

• Some icons in my computer, in Windows Explorer on the desktop, or on the Quick Launch bar change randomly. This problem occurs if the icon cache is not updated correctly. How can I rebuild the icon cache solves this problem

  Some icons in my computer, in Windows Explorer on the desktop, or on the Quick Launch bar change randomly. This problem occurs if the icon cache is not updated correctly. How can I rebuild the icon cache solves this problem

  http://www.Vistax64.com/tutorials/117229-icon-cache-rebuild.html

  How do I rebuild the icon Cache in Vista

  See you soon.

  Mick Murphy - Microsoft partner

• Whenever I open the bridge, I get the Message "bridge has encountered a problem and cannot read the cache. Please try to purge central cache in the cache preferences to correct the situation. »

  Whenever I open the bridge, I get the Message "bridge has encountered a problem and cannot read the cache. Please try to purge central cache in the cache preferences to correct the situation. »

  Please suggest solution.

  Hi Adam,.

  Well, you purge the Cache?

  If not, did you go to the preferences, go to the caching and the last option is to purge the Cache.

  Also @Debbie: you could try to rebuild settings. To do this off bridge and then restart Bridge. However, having fingers on shift-Option-control at the start of Bridge. Keep until a window offering to reset preferences, purge entire thumbnail Cache and reset Standard workspaces. I suggest you choose the first two.

  And Abdul, you might want to try that as well.

  Let us know if this does nothing for you

• Bridge has encountered a problem and cannot read the cache

  For past couple of months, whenever I have start Adobe Bridge directly (and), it gives me an error saying: "bridge has encountered a problem and cannot read the cache. Please try to purge central cache in the Cache preferences to correct the situation. " I do the same through the preferences. And then the bridge takes a long time to load the thumbnails. And next time when I restart Adobe Bridge, same problem.

  It started hapennign all of a sudden for the last two months. It has been previously very quickly.

  Please notify all solutions.

  This notice of page adobe faecebook worked for me:

  Sometimes the purge of preferences is not all MS... So, you can manually go and delete the cache folder Bridge CS6.

  1. exit the bridge
  2. If mac goto: Users/username/Library/Caches/Adobe /.
  3 remove the Bridge CS6 (or whatever version you have) file
  4 restart Bridge. He will rebuild the folder and the files included in this one.

  HTH

• Can someone help me solve the problems Flash install on my iMac and Macbook please?

  OS 10.7.5

  Safari

  On both machines the installation program runs, starts to download the update, is from 7% for about 30 seconds then skip to 47% and abandons the download with the message 'download timeout '.

  It's exactly the same thing every time. I tried to uninstall the previous version of Flash, but it made no difference.

  The things that machines have in common are:

  -they are on the same network, sharing the same internet connection

  -they are running the same version of the OS and Safari (with the exception of the differences between the iMac and Macbook versions)

  I don't know what to try next. Any ideas?

  Thank you

  Hello

  Could you please download Flash Player from the following link: http://helpx.adobe.com/flash-player/kb/installation-problems-flash-player-mac.html#install er

  After the download, close all browsers and double-click on the downloaded file.

  Thank you

  Sunil

• Authentication of JRun & amp; IIS

  After that I connected JRun and IIS on the same machine and tried to open an html
  page I always see a window asking me to provide the user name and
  password. But if I only use IIS (no link with JRun) I'm able to open
  This page in the web browser without any problem. Does anyone know why I get the
  Connection dialog window?
  
  Thank you very much.

  It has proved to be a problem of NTFS permissions.
  After that I assigned the permissions of files and folders targeting designated users, it works fine now.
  Thank you.

• CS4 installation problem: Flash/Dreamweaver/Fireworks does not open

  Hi, I was wondering if someone could help me. I want to install Design premium CS4 on 32-bit Windows Vista. The installation goes by apparently fine, but then when I try to open Dreamweaver, Flash or Fireworks it evokes error message saying

  "The application is not initialilze properly (0xc0150004)" with these details

  Signature of the problem:
  Problem event name: APPCRASH
  Application name: Flash.exe
  Application version: 10.0.0.544
  Application timestamp: 48 c 73089
  Fault Module name: ntdll.dll
  Fault Module Version: 6.0.6002.18005
  Timestamp of Module error: 49e03821
  Exception code: c0150004
  Exception offset: 00009eed
  The system version: 6.0.6002.2.2.0.768.3
  Locale ID: 2057
  Information additional 1: 9 day 13
  More information 2: 1abee00edb3fc1158f9ad6f44f0f6be8
  Information additional 3: 9 day 13
  Additional information 4: 1abee00edb3fc1158f9ad6f44f0f6be8

  All other programs work fine, it's just who does not even open. I tried to reinstall in all different directions that I can think of, without AV, MS SQL and IIS cut, office with selective startup, you name it and it still has the same problem.

  Can anyone help me with what could be the cause of the problem? don't know if its a problem installation or a problem of windows (a setting or something) but I would really like to have ideas anyone might have.

  Thank you

  Tom

  Oh yes, when I look in install also newspapers, it evokes this error

  ERROR

  Journal of: object

  isRunning {string}: 0

  percentComplete {string}: 100

  message {object}: [object Object]

  Journal of: object

  {string} code: 0

  args {object}: [object Object]

  which I think refers to the installer of freezing when you check the profile of the system during installation, but it seems to go through install well. It also has the following errors.

  ERROR

  The payload with AdobeCode: {35304775-CB5F-101B-A142-83B5468C225C} demanded dependence on:

  Family: InDesign

  ProductName: Adobe InDesign CS4 icon Manager x 64

  MinVersion:

  This dependency is not satisfied, because this payload is x 64 and is not supported on this computer.

  Removing this dependency of the list. Product may work correctly.

  Had the same error, try to run Dreamweaver CS4 on my Dell Studio XPS laptop:

  This sorting me and works fine now:

  2. use the registry (Regedit) editor to locate and expand the following registry key:

  'HKEY_LOCAL_MACHINE\COMPONENTS\DerivedData\Components\ '.

  4. from the long list on the left, remove the following key:

  'x86_microsoft.vc80.mfc_1fc8b3b9a1e18e3b_8.0.50727.762_none_0c178a139ee2a7ed '.

  Then uninstall, reboot, and install

• RAM upgrade problem: Flash the BIOS? or upgrade the processor?

  Hi, I jumped in with both feet and now need help to get out me!

  I have a desktop PC HP Pavilion Elite HPE-470uk who becomes a bit slow (processor card here http://ark.intel.com/products/48505/Intel-Core-i3-550-Processor-4M-Cache-3_20-GHz). After you have added a bluray player that I noticed that it's getting a bit slow so thought I would add little RAM.
  

  I bought a few Hyper X8GB of HyperXbeast 1600hhz, slipped in and the PC did nothing but to turn on and off several times. I checked the two sticks and they both do it. I then (plow in front) checked what memory, the processor can handle and discovered "The Intel® Core™ i3 - 5xx / Intel® Core™ i3-21xx processors handle memory DDR3 1066/1333 MHz" by http://www.intel.com/support/processors/corei3/sb/CS-031175.htm

  After a discussion on another forum, that it has been suggested that I have updated the BIOS because it can allow the processor to manage memory 1600 mhz, but I don't know where to start on this or what version to selected download. I'd appreciate any help you can offer on this.

  The other way, that I can see is to update the processor itself. I thought of nothing too fancy just an i5 because it will allow me to run 3d blurays and should allow me to run some apps at the same time. After reading this http://m.wikihow.com/Upgrade-a-Processor it seems too complicated. Is it really just a matter of taking off the fan, declipsant the old processor, nine droping in and then put on some cooling stick stuff?

  Or should I just return the memory and get good memory?

  See you soon

  Atdot.

  Here are the specifications of original factory for your desktop HP Pavilion Elite HPE-470uk and its card mother MS-7613 (Iona-GL8E). Based on these specifications, this model can support up to 16 GB (4 GB x 4 DIMMs) as follows:

  Dual channel memory architecture
  Four DDR3 DIMM sockets (240 pin)
  PC3-10600 (DDR3-1333)
  PC3-8500 (DDR3-1066)
  Memory non - ECC, unbuffered
  Supports up to 16 GB on 64 bit computers

  In addition, this model can support the following Intel processors;

  Maximum frequency of the processor of the heart < = 2.93GHz
  Intel Core i7 - 8xx (Lynnfield core)
  Intel Core i5 - 7xx (Lynnfield core)
  Intel Core i5 - 6xx (Clarkdale core)
  Intel Core i3 - 5xx (Clarkdale core)

  If you do not have to worry about the update of the BIOS, there is no updates available for your computer BIOS. Honestly, I return the incorrect memory and upgrade to a minimum of 8 GB of RAM. Then, if it solves all your problems, you could also upgrade the processor.

  As the computer is nearly 4 years old, you can consider a factory HP restore to return the computer to a facoty as State. In many cases, it returns original full speed of the computer. The reason why this helps, because the BONE is swollen and clogged over time.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• Rendering problem Flash player video

  Hello I have a problem with my flash video. When I play the YouTube video and scroll with my mouse wheel, the static part of the video is redrawn with the rest of the site. The dynamic part is rendered correctly. It is difficult to explain in words so please see the photo.

  Does anyone have an idea how to solve this problem? Already tried reinstalling the flash plugin.

  Do not hesitate to ask another info of what you need to know to help me solve this problem.

  Firefox 4 beta uses the Direct2D GPU acceleration, try turning off all: config

  change "mozilla.widget.render" to 0.

• SSL connection problem

  Hi, I tried to connect to a server (Openfire) XMPP set up on my machine of. I'm an EOFException at the opening of the connection:

  SecureConnection secureConnection = (SecureConnection) Connector.open("ssl://10.14.1.94:5222;deviceside=true", Connector.READ_WRITE);
  

  I tried pointing to another server XMPP (talk.google.com) and instead, I had a TLSIOException.

  What is a certificate problem? The Openfire Server uses a self-signed certificate.

  Thank you!

  OK I found the solution and it's a little embarrassing, I was using port 5222, but the server was listening on port 5223 ssl...

• Installation of SSL VPN problem

  Hi all

  I am setting up a SSL VPN on our ASA 5510 using the Secure Mobility client.  After working through several problems, I was able to get the test server to download and install the Linux client, and he says that it is connected.  When I try to ping any server in the LAN, however, the first ping is responded to and the rest of out time.  On the firewall, I see a stream of errors like this:

  3

  October 11, 2014

  16:12:58

  SRV1

  172.16.40.185

  Refuse icmp incoming outside CBC: SRV1 outside dst: 172.16.40.185 (type 0, code 0)

  split tunneling seems to work fine, I can access the Internet yet, but any attempt to reach a server in the LAN will expire.

  Now I have had this before working with a Windows and a Mac client, but removed this configuration and (I thought) completely recreated when I updated the anyconnect images to include an image of linux.  Now I get this same problem with all 3 platforms.

  Can anyone advise me on what I may be missing or that I can provide to diagnose the problem?

  ASA is running v8.2 (5)

  I followed this guide to set up: http://www.techrepublic.com/blog/data-center/eight-easy-steps-to-cisco-a...

  Thank you!

  Ok thank you.

  If your clients are assigned addresses of:

  mask 172.16.40.185 - 172.16.40.190 255.255.252.0 IP local pool VPNTestPool

  You have exempted from this pool of NAT with the last entry in your acl sheep:

  access-list sheep extended permits all ip 172.16.40.184 255.255.255.248

  A potential problem I see is that the pool is a subnet dug into your internal network:

  IP 172.16.40.2 255.255.252.0

  The ASA believe hosts on this subnet to be connected, and your heart can be confused on the way forward.

  In addition, I don't see where you set the

   sysopt connection permit-vpn

  .. .command recommended in the configuration guide you followed.

  Also. in the first packet - trace, the source for client VPN traffic must be outside, not inside.

• Audio problems (Flash Professional CS6)

  I have 2 problems:

  I have a problem with the audio. The problem is that if I play audio lets say in the middle of the audio editing and press play, it will not play the song. But if I play of

  the beginning, the sound will play.

  My second problem is that

  Even if I play the audio from the beginning, and then press ENTER again to stop the music, it's just going to keep playing the audio.

  If you have encountered this problem on Flash CS6 professional or animate the CC (which I think has the same options as Flash Professional CS6)

  Please answer me.

  

• White screen problem Flash 20.0.0.267 - URGENT!

  Since the last update (.267 - made December 28, 2015) flash, download our application can not load correctly.

  After loading, the app (under IE) displays a white screen (image below).

  To downgrade to a previous version (20.0.0.228), it works fine.

  Many of my colleagues who run similar applications using Flash are the white screen problem and our customers are furious

  
  

  Why is this?

  How can it be solved without asking all customers to downgrade their versions of Flash?

  Please help as soon as POSSIBLE.

  

  Hello

  20.0.0.270 is now Live. It contains the fix for the problem.

  Thank you

• Failure of the conversion due to SSL certificate problems - can work around this problem?

  I began the process of migration of a collection of virtual machines in an environment of KVM to an existing cluster of vSphere and try to use the converter (5.5) do a dynamic conversion/migration of a Ubuntu box, but it does not reason create the virtual disk on one of the hosts because of the SSL certificate, and I found no other messages or articles specifically on this (looks like most associated with SSL include improving speed)

  In the worker newspaper, I can see that:

  • The converter is able to successfully create the target VM
  • The attempt to create the virtual disk is defective for the certificate SSL is not invalid (all systems in the cluster appear to be using default certificates from VMware).  In the log file of the worker:

  2014-08 - 07T 09: 35:13.947 - 07:00 [warning 06620 'Default'] [, 0] SSL_IsVerifyEnabled: failed to read the registry value. Falling back to the default behavior: verification on. LastError = 0

  2014-08 - 07T 09: 35:13.947 - 07:00 [warning 06620 'Default'] [, 0] SSL: SSL unknown error

  2014-08 - 07T 09: 35:13.947 - 07:00 [warning 06620 'Default'] [, 0] SSL: connection failed

  2014-08 - 07T 09: 35:13.947 - 07:00 [warning 06620 'Default'] [, 0] NfcNewAuthdConnectionEx [NFC ERROR]: unable to connect to peer. Error: The certificate of the remote host has these problems:

  ->

  -> * The host certificate chain is incomplete.

  ->

  -> * unable to get local issuer certificate

  2014-08 - 07T 09: 35:13.947 - 07:00 [info 06620 'Default'] Sysimgbase_DiskLib_OpenWithPassPhrase failed with 'NBD_ERR_NETWORK_CONNECT' (error code: 2338)

  • The goal of the virtual machine is removed.

  Is it possible to simply disable the validation of certificate for this process?  In the newspaper, it looks like a registry key that it would control, but I have not found any information on this subject (or guessed correctly).  Or can I import this certificate on the local Windows system running converter to get around it (I could not with this approach, but either)

  It's really not clear to me which system validation.  While the worker log shows it connect to the vSphere host, there is no such line indicating it connects to the host where the target VM is located, and it looks like this is the host with the certificate which is considered not valid.   Validation occurs not on my local system running the converter? (the parameters of the vCenter server shows that the box 'vCenter requires a verification of certificates SSL host' is unchecked already)

  Thank you

  Scott

  You might want to take a look at Re: an error occurred when opening a virtual disk. Make sure that the converter server and source running machines have network access to the ESX/ESXi hosts source and destination and let me know if it works for you.