SSL VPN error: no assigned address

Similar Questions

• agent of SSL VPN error without reason

  Hello

  Message error please refer to the attachment.

  If I'm right, this may be caused by the service of Sharing (ICS) Internet connection I used the network cable with my iPhone by creation-to-peer wireless network at the hotel and before that, she worked normally all the time.

  For the moment, I can also connect VPN successfully but the State always change to "reconnect" after 8 seconds and error message popup after that many try.

  I put the function ICS 'manual' or 'disabled' and make sure that it is not in running, but not useful.

  OS: Win7 Pro x 64 Sp1

  AnyConnect VPN Version client: 2.5.6005

  A response would be appreciated.

  Andy Xu

  There is error in the SSL protocol stack. try to reinstall the vpn client. It can work.

  I found the information for the error you get below.

  The VPN client agent SSL engine encountered an error. Please retry, or restart AnyConnect. 

  Description AnyConnect has encountered an unexpected and unrecoverable error in the SSL protocol stack. One possible cause is a flaw AnyConnect.

  Recommended user response restart the computer or the device, and then try to start a new VPN connection. If the problem persists, run DART (see DART helps collect troubleshooting information) and report the error to technical support for your organization and include the DART bundle.

  Recommended response administrator if the problem persists, open a case with the Assistance Center (TAC) Cisco technical and include the DART bundle.

  Here is the link

  http://www.Cisco.com/en/us/docs/security/vpn_client/AnyConnect/anyconnect25/user/messages/AC25-VPN-user-msgs.html

• THE SSL VPN CLIENT ERROR!

  VPN concentrator running 4.7. I have to connect to the web vpn session. The SSL VPN Client installs. Message that says: "so that the SSL VPN connection is pending" and later another message appears that says "HTTP RESPONSE received from gateway SSL VPN is not valid" appears.

  What is strange is that the VPN concentrator lists me as it is connected with an IP address assigned to the ACS, but I can't access anything whatsoever. BTW, no ACLs WEB or IP filters are configured for this group that would not allow me access to the network. In addition, with the same information identification and the same group, I have no problem to access the network when the client SSL VPN is not configured to be used. IE web vpn before 4.7.

  Any ideas?

  The "VPN SSL HTTP RESPONSE received from gateway is incorrect" message may appear if the configuration of the client of the concentrator contains over split tunneling 26 entries.

• SSL VPN Client - version 4.7 WebVPN session is over; Port error.

  Hi, I just upgraded to 4.7 and trying of the SSL VPN Client.

  He seems to spend the largest part of the installation on client machines. I tried more than one, ut I get this error from port.

  Any ideas?

  Try asigning the user, an ip address on the hub

• Error of java SSL VPN "ClassNotFoundException".

  I have a user who cannot access their bookmarks of Sonicwall Java running on our appliance virtual sonciwall. 5 HTML5 works, but it's slow and Active X works, but she would like to remotely from his mac, so I thought that java would be the best bet except that I cannot make it work in Internet Explorer. U45 8 Java is installed and active, however, when you click on the bookmark, we receive the below error.

  In the control panel under mixed Code Java, I've already activated "enable - hide warning and run with protections" and I added to the URL of the site on the Security tab, does anyone else have this problem?

  The firmware on our virtual appliance of Sonicwall's SonicOS SSL - VPN 8.0.0.1 - 16sv

  

  Pstoric you can open a support ticket with us?

  There are a few things, we want to check.

  It will be when you have access to the machine in question, of course.

• SSL VPN IP address other than the IP address of the interface?

  Hi,
  
  Is it possibe to use a differnt IP Address from the same Subnet of OUTSIDE
  
  INTERFACE? Instead of Interface IP Address itself. The Idea behind is,
  
  Clients should not use OUTSIDE Interface IP Address for SSL VPN, but whereas they can
  
  use from the IP Address Pool of OUTSIDE Interface.
  Regards

  Brassart Abbas

  If SSL is completed on an ASA firewall, you can finish it on all other ip addresses but the external interface.

  If it is completed on a router IOS, Yes, you can use a different ip address to put an end to the SSL VPN connection.

  Hope that answers your question.

• ASA 5520: SSL VPN by using a different IP address that the ASA public IP address

  Hi guys,.

  I'm trying to configure an SSL VPN on a Cisco ASA5520.

  Unfortunately port 443 interface OUTSIDE of the SAA is already used by Microsoft Outlook Web Access and I can not change the configuration of Outlook. This configuration already in place allows me to use the public IP address of the ASA as IP Cisco VPN for the Web page.

  I don't not want to use a different port so to keep life easy for users.

  I have a few available public IPs that I can use so I wanted to use one of them instead of the OUTSIDE of the ASA interface. Any idea how I could do?

  Thank you

  Dario

  Unfortunately you can not use any other public ip address, except the ASA outside IP interface to complete the SSL VPN.

  The only options that you have is to change the Outlook to use another port or the SSL VPN to use a different port.

• SSLVPN package SSL-VPN-Client (seq:1): installed error: others

  "Try to install the package anyconnect-victory - 2.5.2019 - k9.pkg on a Cisco 1811 running c181x-advipservicesk9 - mz.124 - 22.T5.bin router, when I run the command in config mode" webvpn install flash: anyconnect svc - win - 2.5.2019 - k9.pkg ' I get "

  "SSLVPN package SSL-VPN-Client (seq:1): installed error: others" some proposed to reformat the flash drive, does anyone know a workaround or a way to do it without losing the configuration running?  I think that there is a problem with the structure of files on the router, the installation package is capable of "webvpn" installation directory.  All ideas are welcome, thanks!

  hostname #sh flash
  -# - length - time - path
  1 23472512 February 23, 2012 21:10:34 c181x-advipservicesk9 - mz.124 - 22.T5.bin
  2 0 23 February 2012 21:37:50 webvpn
  3 4686889 23 February 2012 21:18:46 anyconnect-victory - 2.5.2019 - k9.pkg

  3772416 bytes available (28168192 bytes used)

  Processor of 1811 (MPC8500) Cisco (revision 0 x 400) with 118784K / 12288K bytes of memory.
  10 FastEthernet interfaces
  Serial 1 interface
  1 line of terminal
  31360K bytes of ATA CompactFlash (read/write)

  Configuration register is 0 x 2102

  Host name #.

  I think it's because you have not enough space - he's trying to copy the file to the directory of webvpn.

  Make sure that the install webvpn command isn't in your configuration.

  Move the anyconnect package in the directory of webvpn

  run

  WebVPN install svc flash:/webvpn/anyconnect-win-2.5.2019-k9.pkg

  And see if that helps.

• Installation of SSL VPN problem

  Hi all

  I am setting up a SSL VPN on our ASA 5510 using the Secure Mobility client.  After working through several problems, I was able to get the test server to download and install the Linux client, and he says that it is connected.  When I try to ping any server in the LAN, however, the first ping is responded to and the rest of out time.  On the firewall, I see a stream of errors like this:

  3

  October 11, 2014

  16:12:58

  SRV1

  172.16.40.185

  Refuse icmp incoming outside CBC: SRV1 outside dst: 172.16.40.185 (type 0, code 0)

  split tunneling seems to work fine, I can access the Internet yet, but any attempt to reach a server in the LAN will expire.

  Now I have had this before working with a Windows and a Mac client, but removed this configuration and (I thought) completely recreated when I updated the anyconnect images to include an image of linux.  Now I get this same problem with all 3 platforms.

  Can anyone advise me on what I may be missing or that I can provide to diagnose the problem?

  ASA is running v8.2 (5)

  I followed this guide to set up: http://www.techrepublic.com/blog/data-center/eight-easy-steps-to-cisco-a...

  Thank you!

  Ok thank you.

  If your clients are assigned addresses of:

  mask 172.16.40.185 - 172.16.40.190 255.255.252.0 IP local pool VPNTestPool

  You have exempted from this pool of NAT with the last entry in your acl sheep:

  access-list sheep extended permits all ip 172.16.40.184 255.255.255.248

  A potential problem I see is that the pool is a subnet dug into your internal network:

  IP 172.16.40.2 255.255.252.0

  The ASA believe hosts on this subnet to be connected, and your heart can be confused on the way forward.

  In addition, I don't see where you set the

   sysopt connection permit-vpn

  .. .command recommended in the configuration guide you followed.

  Also. in the first packet - trace, the source for client VPN traffic must be outside, not inside.

• Router WAN double with SSL VPN inaccessible for customers

  I have a configured in a Dual WAN setup Cisco 888. There is an ADSL link connected to the VLAN 100 and a SDSL link associated with the Dialer0. The customer wishes to use the ADSL link to the normal navigation and external SSL VPN users to complete on the SDSL connection. I tried to configure the link failover for the ADSL SDSL.

  What works:

  -Access to the Internet for clients the

  What does not work:

  -The ADSL SDSL connection failover.

  -Access SSL VPN for customers. Surf to the external IP address will cause only a page by default HTTP. Specification webvpn.html results in a 404 not found error.

  Here is my configuration:

  version 15.0

  no service button

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  no password encryption service

  !

  host name x

  !

  boot-start-marker

  boot-end-marker

  !

  logging buffered 51200 warnings

  enable secret 5 x

  !

  AAA new-model

  !

  !

  AAA authentication login local sslvpn

  !

  !

  !

  !

  !

  AAA - the id of the joint session

  iomem 10 memory size

  !

  Crypto pki trustpoint TP-self-signed-3964912732

  enrollment selfsigned

  name of the object cn = IOS - Self - signed - certificate - 3964912732

  revocation checking no

  rsakeypair TP-self-signed-3964912732

  !

  !

  TP-self-signed-3964912732 crypto pki certificate chain

  self-signed certificate 03

  x

  quit smoking

  IP source-route

  !

  !

  IP dhcp excluded-address 192.168.10.254

  DHCP excluded-address IP 192.168.10.10 192.168.10.20

  !

  DHCP IP CCP-pool

  import all

  network 192.168.10.0 255.255.255.0

  default router 192.168.10.254

  DNS-server 213.75.63.36 213.75.63.70

  Rental 2 0

  !

  !

  IP cef

  no ip domain search

  property intellectual name x

  No ipv6 cef

  !

  !

  udi pid CISCO888-K9 sn x license

  !

  !

  username secret privilege 15 ciscoadmin 5 x

  username password vpnuser 0 x

  !

  !

  LAN controller 0

  atm mode

  Annex symmetrical shdsl DSL-mode B

  !

  interface Loopback1

  Gateway SSL dhcp pool address description

  IP 192.168.250.1 255.255.255.0

  !

  interface Loopback2

  Description address IP VPN SSL

  IP 10.10.10.1 255.255.255.0

  route PBR_SSL card intellectual property policy

  !

  interface BRI0

  no ip address

  encapsulation hdlc

  Shutdown

  Multidrop ISDN endpoint

  !

  ATM0 interface

  no ip address

  load-interval 30

  No atm ilmi-keepalive

  PVC KPN 2/32

  aal5mux encapsulation ppp Dialer

  Dialer pool-member 1

  !

  !

  interface FastEthernet0

  switchport access vlan 100

  !

  interface FastEthernet1

  !

  interface FastEthernet2

  !

  interface FastEthernet3

  !

  interface Vlan1

  LAN description

  IP address 192.168.10.254 255.255.255.0

  IP nat inside

  IP virtual-reassembly

  IP tcp adjust-mss 1300

  !

  interface Vlan100

  Description KPN ADSL 20/1

  DHCP IP address

  NAT outside IP

  IP virtual-reassembly

  !

  interface Dialer0

  Description KPN SDSL 2/2

  the negotiated IP address

  IP access-group INTERNET_ACL in

  NAT outside IP

  IP virtual-reassembly

  encapsulation ppp

  Dialer pool 1

  Dialer-Group 1

  PPP pap sent-username password 0 x x

  No cdp enable

  !

  IP local pool sslvpnpool 192.168.250.2 192.168.250.100

  IP forward-Protocol ND

  IP http server

  local IP http authentication

  IP http secure server

  IP http timeout policy slowed down 60 life 86400 request 10000

  !

  pool nat SSLVPN SDSL 10.10.10.1 IP 10.10.10.1 netmask 255.255.255.0

  IP nat inside source static tcp 10.10.10.1 443 interface Dialer0 443

  IP nat inside source static tcp 10.10.10.1 80 Dialer0 80 interface

  IP nat inside source overload map route NAT_ADSL Vlan100 interface

  IP nat inside source overload map route NAT_SDSL pool SSLVPN SDSL

  IP route 0.0.0.0 0.0.0.0 x.x.x.x

  IP route 0.0.0.0 0.0.0.0 Dialer0 10

  !

  INTERNET_ACL extended IP access list

  Note: used with CBAC

  allow all all unreachable icmp

  allow icmp all a package-too-big

  allow icmp all once exceed

  allow any host 92.64.32.169 eq 443 tcp www

  deny ip any any newspaper

  Extended access LAN IP-list

  permit ip 192.168.10.0 0.0.0.255 any

  refuse an entire ip

  !

  Dialer-list 1 ip protocol allow

  not run cdp

  !

  !

  !

  !

  NAT_SDSL allowed 10 route map

  match the LAN ip address

  match interface Dialer0

  !

  NAT_ADSL allowed 10 route map

  match the LAN ip address

  match interface Vlan100

  !

  PBR_SSL allowed 10 route map

  set interface Dialer0

  !

  !

  control plan

  !

  !

  Line con 0

  no activation of the modem

  line to 0

  line vty 0 4

  privilege level 15

  transport input telnet ssh

  !

  max-task-time 5000 Planner

  !

  WebVPN MyGateway gateway

  hostname d0c

  IP address 10.10.10.1 port 443

  redirect http port 80

  SSL trustpoint TP-self-signed-3964912732

  development

  !

  WebVPN install svc flash:/webvpn/anyconnect-dart-win-2.5.0217-k9.pkg sequence 1

  !

  WebVPN install svc flash:/webvpn/anyconnect-macosx-i386-2.5.0217-k9.pkg sequence 2

  !

  WebVPN install svc flash:/webvpn/anyconnect-macosx-powerpc-2.5.0217-k9.pkg sequence 3

  !

  WebVPN context SecureMeContext

  title "SSL VPN Service"

  secondary-color #C0C0C0

  title-color #808080

  SSL authentication check all

  !

  login message "VPN".

  !

  Group Policy MyDefaultPolicy

  functions compatible svc

  SVC-pool of addresses "sslvpnpool."

  SVC Dungeon-client-installed

  Group Policy - by default-MyDefaultPolicy

  AAA authentication list sslvpn

  Gateway MyGateway

  development

  !

  end

  Any suggestions on where to look?

  Hello

  It works for me. When the client tries to resolve the fqdn for the domain specified in "svc split dns.." he will contact the DNS server assigned through the Tunnel. For all other questions, he contacts the DNS outside the Tunnel.

  You can run a capture of packets on the physical interface on the Client to see the query DNS leaving?

  Also in some routers, DNS is designated as the router itself (who is usually address 192.168.X.X), if you want to make sure that assigned DNS server doesn't not part of the Split Tunnel.

  Naman

• SSL VPN issues

  Hello

  We have had problems with the SSL VPN for quite awhile, but don't seem to be getting anywhere.

  This is an intermittent problem that we can not simply track down.

  Users can connect to the VPN, get an IP address and show as connected on GEORGE page.
  Users concerned, always shows a time of 0: logon. If they try to access anything whatsoever, they cannot, as looks that all traffic is blocked.
  I ran a trace of packets to an affected user, and it shows this. To me, it looks like a firewall policy blocks.

  (* Parcel number: 1 * header values: bytes captured: 74, real bytes on the wire: 74 Packet Info(Time:02/19/2016 18:01:42.256): in: X 1 * (interface), out:-, DROPPED, Code Drop: 582 Id of Module (package abandoned-denied by SSLVPN under user control strategy),: 27 (policy), (Ref.Id: _968_qpmjdzDifdl), 18:31) ether header Ethernet Type: IP (0 x 800), Src = [00:11:22:33:44:55], Dst = [c2 [:ea:e4:b1:8 b: 23] Type of IP header IP Packet: ICMP (0 x 1), Src = [192.118.201.6], [172.18.1.252] = Type ICMP ICMP Packet Header Dst = 8 (ECHO_REQUEST), ICMP Code = 0, 19407 value = ICMP checksum: [2] dump hexadecimal and ASCII of the package: c2eae4b1 8 b 230011 22334455 and 08004500 003c1a76 00008001 *... #... "3DU... E...<.v....* e8bfc076="" c906ac12="" 01fc0800="" 4bcf0001="" 018c6162="" 63646566="" *...v........k.....abcdef*="" 6768696a="" 6b6c6d6e="" 6f707172="" 73747576="" 77616263="" 64656667="" *ghijklmnopqrstuvwabcdefg*="" 6869="" *hi="">

  The only solution is to unplug / reconnect several times, until he started working. We cannot find a reason for this. Somedays it works very good and other days it is not.
  

  Any help would be greatly appreciated.

  Thank you

  Hello

  Just came across the same problem.

  We had some additional IP address ranges that had to go through the firewall on SSLVPN. I beilive source was the same.

  When configuring users > local users must also assign in selected authorized user access VPN (pencil icon on the right of the user name) Configure > VPN access.

  Once I created the Group of subnet for all subnets internal and permitted all Local defined users to access this group for VPN access settings, all traffic began to flow.

  I see that 1/2 of last year, but I just joined.

  Kind regards

  Rajko

• access of entrepreneurs and employees of the web site in-house using clientless ssl vpn.

  We have a layout of web SSL VPN without customer who allow employees and suppliers of connection and internal display web page.  I wonder if possible separate employees and contractors to access internal pages.  The internal web page has no authentication of users.  They would like to see if it is possible that traffic employees get proxy behind interface INSIDE IP de ASA and entrepreneur behind a different IP address proxy traffic.  Thus, the internal web page can check IP to contractor and only give them access to view certain web page, but not all pages.

  Hello

  Creating a group policy for each user group will be a good option, you can also use DAP to assign an ACL web to the user who logs on the portal without client, you can use the Radius, LDAP or Cisco attributes to associate the DAP for the user. For example, if you are using LDAP, you can create 2 groups separated here for employees and entrepreneurs and based on the LDAP user group membership, they will be assigned to specific web acl configured according to their access restrictions.

  You can follow this link to set up an acl of web:

  http://www.Cisco.com/c/en/us/TD/docs/security/ASA/asa83/asdm63/Configura...

  Once the ACL is ready, you can follow this guide to configure the DAP Protocol: "check the web for acls figure10.

  http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...

  Thank you, please note!

• IP NAT on the router on SSL - VPN appliance

  Someone at - it allows to transmit 443/SSL on a SSL VPN Cisco 891 - K9 unit?

  (I have never encountered this situation before as the router VPN terminated public face directly or we had several IPs public to assign the VPN device directly a public IP address).

  With ' ip nat inside source static tcp 44.55.66.255 443 10.10.10.150 443 extensible "is supposed to pass the SSL request to the appliance SSL VPN to 10.10.10.150 to have VPN applications ended here.

  But failed miserably body 891 - K9 created a virtual ARP entry for 10.10.10.150. So two MACs with the same IP address.

  So 443 requests were sent to its interface. At the hearing of NAT, I can't ssh inside SSL - VPN, but by the time the statemet disappeared, I can ssh and warning dupliacte ARP goes.

  * 1 Nov 19:22:46.871: % IP-4-DUPADDR: duplicate address 10.10.10.150 on Vlan10, a source of aaaa.bbbb.cccc
  * 1 Nov 19:23:18.083: % IP-4-DUPADDR: duplicate address 10.10.10.150 on Vlan10, a source of aaaa.bbbb.cccc
  * 1 Nov 19:23:48.295: % IP-4-DUPADDR: duplicate address 10.10.10.150 on Vlan10, a source of aaaa.bbbb.cccc
  RTR #sh clock
  * 19:24:26.487 UTC Sunday, November 1, 2015
  RTR #sh ip arp 10.10.10.150
  Protocol of age (min) address Addr Type Interface equipment
  Internet 10.10.10.150 - e02f.6d96.8dd0 ARPA Vlan10
  RTR #sh ip arp 10.10.10.150
  Protocol of age (min) address Addr Type Interface equipment
  Internet 10.10.10.150 - e02f.6d96.8dd0 ARPA Vlan10
  RTR #sh sh ip route 10.10.10.150

  Cisco TAC to reproduce this problem at the moment to report dev.

  Does anyone else have this problem or a workaround?

  Thank you.

  I may be misunderstanding but isn't your NAT statement backwards IE. If you want traffic to pass to 10.10.10.150 it shouldn't be-

  ' ip nat inside source static tcp 10.10.10.150 43 43 44.55.66.25x.

  isn't the device for SSL connection on interface 'ip nat inside '?

  Jon

• Cannot access internal network so AnyConnect SSL VPN, ASA 9.1 (6)

  Hello Cisco community support,

  I have a lab which consists of two virtual environments connected to a 3750-G switch that is connected to a 2901 router which is connected to an ASA 5512 - X which is connected to my ISP gateway. I configured SSL VPN using AnyConnect and can establish a VPN to the ASA from the outside but once connected, I can't access internal network resources or access the internet. My information network and ASA configuration is listed below. Thank you for any assistance you can offer.

  ISP network gateway: 10.1.10.0/24

  ASA to the router network: 10.1.40.0/30

  Pool DHCP VPN: 10.1.30.0/24

  Network of the range: 10.1.20.0/24

  Development network: 10.1.10.0/24

  : Saved
  :
  : Serial number: FCH18477CPT
  : Material: ASA5512, 4096 MB RAM, CPU Clarkdale 2793 MHz, 1 CPU (2 cores)
  :
  ASA 6,0000 Version 1
  !
  hostname ctcndasa01
  activate bcn1WtX5vuf3YzS3 encrypted password
  names of
  cnd-vpn-dhcp-pool 10.1.30.1 mask - 255.255.255.0 IP local pool 10.1.30.200
  !
  interface GigabitEthernet0/0
  nameif inside
  security-level 100
  IP 10.1.40.1 255.255.255.252
  !
  interface GigabitEthernet0/1
  nameif outside
  security-level 0
  address IP X.X.X.237 255.255.255.248
  !
  interface GigabitEthernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/5
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  management only
  nameif management
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  boot system Disk0: / asa916-1-smp - k8.bin
  boot system Disk0: / asa912-smp - k8.bin
  passive FTP mode
  permit same-security-traffic intra-interface
  network of the NETWORK_OBJ_10.1.30.0_24 object
  10.1.30.0 subnet 255.255.255.0
  network obj_any object
  network obj_10.1.40.0 object
  10.1.40.0 subnet 255.255.255.0
  network obj_10.1.30.0 object
  10.1.30.0 subnet 255.255.255.0
  outside_access_in list extended access permitted ip object NETWORK_OBJ_10.1.30.0_24 all
  FREE access-list extended ip 10.1.40.0 NAT allow 255.255.255.0 10.1.30.0 255.255.255.0
  access-list 101 extended allow any4 any4-answer icmp echo
  access-list standard split allow 10.1.40.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  management of MTU 1500
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any inside
  ICMP allow all outside
  ASDM image disk0: / asdm - 743.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside, outside) source obj_10.1.40.0 destination obj_10.1.40.0 static static obj_10.1.30.0 obj_10.1.30.0 non-proxy-arp-search to itinerary
  NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.1.30.0_24 NETWORK_OBJ_10.1.30.0_24 non-proxy-arp-search to itinerary
  Access-group outside_access_in in interface outside
  !
  Router eigrp 1
  Network 10.1.10.0 255.255.255.0
  Network 10.1.20.0 255.255.255.0
  Network 10.1.30.0 255.255.255.0
  Network 10.1.40.0 255.255.255.252
  !
  Route outside 0.0.0.0 0.0.0.0 10.1.10.1 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  without activating the user identity
  identity of the user by default-domain LOCAL
  Enable http server
  http 192.168.1.0 255.255.255.0 management
  http 192.168.1.0 255.255.255.0 inside
  http X.X.X.238 255.255.255.255 outside
  No snmp server location
  No snmp Server contact
  Crypto ipsec pmtu aging infinite - the security association
  Crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0
  registration auto
  full domain name no
  name of the object CN = 10.1.30.254, CN = ctcndasa01
  ASDM_LAUNCHER key pair
  Configure CRL
  trustpool crypto ca policy
  string encryption ca ASDM_Launcher_Access_TrustPoint_0 certificates
  certificate c902a155
  308201cd 30820136 a0030201 020204c 0d06092a 864886f7 0d 010105 9 02a 15530
  0500302b 31133011 06035504 03130 has 63 61736130 31311430 12060355 74636e64
  0403130 31302e31 2e33302e 32353430 1e170d31 35303731 32303530 3133315a b
  170d 3235 30373039 30353031 33315 has 30 2 b 311330 0403130a 11060355 6374636e
  64617361 30313114 30120603 55040313 0b31302e 312e3330 2e323534 30819f30
  0d06092a 864886f7 010101 05000381 8 d 0d 003081 89028181 00a47cfc 6b5f8b9e
  9b106ad6 857ec34c 01028f71 d35fb7b5 6a61ea33 569fefca 3791657f eeee91f2
  705ab2ea 09207c4f dfbbc18a 749b19ae d3ca8aa7 3370510b a5a96fd4 f9e06332
  4355 db1a4b88 475f96a1 318f7031 40668a4d afa44384 819d fa164c05 2e586ccc
  3ea59b78 5976f685 2abbdcf6 f3b448e5 30aa96a8 1ed4e178 0001300 020301 4 d d
  06092a 86 01010505 00038181 0093656f 639e138e 90b69e66 b50190fc 4886f70d
  42d9b4a8 11828da4 e0765d9c 52d84f8b 8e70747e e760de88 c43dc5eb 1808bd0f
  fd2230c1 53f68ea1 00f3e956 97eb313e 26cc49d7 25b927b5 43d8d3fa f212fcaf
  59eb8104 98e3a1d9 e05d3bcb 428cd7c6 61b530f5 fe193d15 ef8c7f08 37ad16f5
  d8966b50 917a88bb f4f30d82 6f8b58ba 61
  quit smoking
  Telnet timeout 5
  SSH stricthostkeycheck
  SSH timeout 5
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  VPN-addr-assign local reuse / 360 time
  management of 192.168.1.2 - dhcpd address 192.168.1.254
  enable dhcpd management
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  Trust ASDM_Launcher_Access_TrustPoint_0 vpnlb-ip SSL-point
  SSL-trust outside ASDM_Launcher_Access_TrustPoint_0 point
  WebVPN
  allow outside
  AnyConnect image disk0:/anyconnect-linux-3.1.09013-k9.pkg 4
  AnyConnect image disk0:/anyconnect-macosx-i386-3.1.09013-k9.pkg 5
  AnyConnect image disk0:/anyconnect-win-3.1.09013-k9.pkg 6
  AnyConnect enable
  tunnel-group-list activate
  internal GroupPolicy_cnd-vpn group policy
  GroupPolicy_cnd-vpn group policy attributes
  WINS server no
  value of server DNS 8.8.8.8
  client ssl-VPN-tunnel-Protocol
  by default no
  xxxx GCOh1bma8K1tKZHa username encrypted password
  type tunnel-group cnd - vpn remote access
  tunnel-group global cnd-vpn-attributes
  address-cnd-vpn-dhcp-pool
  strategy-group-by default GroupPolicy_cnd-vpn
  tunnel-group cnd - vpn webvpn-attributes
  activation of the alias group cnd - vpn
  !
  ICMP-class class-map
  match default-inspection-traffic
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map icmp_policy
  icmp category
  inspect the icmp
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  !
  global service-policy global_policy
  service-policy icmp_policy outside interface
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:261228832f3b57983bcc2b4ed5a8a9d0
  : end
  ASDM image disk0: / asdm - 743.bin
  don't allow no asdm history

  Can you confirm that this is correct, your diagram shows your IP address public on ASA as 30 while you have assinged on 'outside' interface like 29?

• WebVPN and remote vpn, ssl vpn anyconnect

  Hi all

  Differences between webvpn and remote vpn, ssl vpn anyconnect
  All require a separate license?

  Thank you

  Hello

  The difference between the webvpn and SSL VPN Client is the WebVPN to use SSL/TLS and port

  send through a java application to support the application, it also only supports TCP for unicast traffic, no ip address

  address is assigned to the customer, and the navigation on the web in the tunnel is made with a SSL

  Web-mangle that allows us stuff things in theSSL session.

  SSL VPN (Anyconnect) Client is a client of complete tunneling using SSL/TCP, which installs an application on the computer and

  envelopes vpn traffic in the ssl session and thus also an assigned ip address has the

  tunnel's two-way, not one-way.   It allows for the support of the application on the

  tunnel without having to configure a port forward for each application.

  AnyConnect is a client of new generation, which has replaced the old vpn client and can be used as long as the IPSEC vpn ssl.

  For anyconnect licenses please see the link below:

  http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/ANYC...

  Kind regards

  Kanwal