Starting Dell U2713HM resolution problem

Similar Questions

• Dell U2412M resolution problem

  Try to change the resolution to 1280 x 800.  Instead of 1280 x 800, he turns in 1280 x 960.  Any thoughts?  TIA

  The proper for the U2412M resolution is 1920 x 1200 60 Hz. It can do the following lower resolutions:
  1920 x 1080
  1680 x 1050
  1600 x 1200
  1280 x 1024
  1024 x 768
  800 x 600
  720 x 400
  640 x 480

  Any other resolution is cuased by the video card driver and is considered to be "custom".

• Dell Studio 1555 - screen resolution problem

  As I said, I have a Studio 1555 purchased in 2009. Recently, I had a hard disk problem and had to replace it. With replacement, I reinstalled Vista and drivers; However, the resolution of the screen only now allows up to 1152 x 864 - which spans a bit the screen horizontally. My hard drive before, it only lasted in the slightest. I think that I can not have installed the factory properly drivers, but I'm not positive. My replacement hard drive is slower (5400 RPM as apposed to my previous 7200 RPM), but I was told that this would have nothing to do with my resolution problem. Any thoughts? I'm a graphics guy and amateur photographer, so this problem of resolution just doesn't fly. Any help would be greatly appreciated.

  Update: it was indeed a driver didn't install I guess. I installed it and everything is right with the world now.

• Dell U2713HM on Asus HD7970-DC2T

  Starting today, I am the proud owner of a Dell U2713HM monitor, which I connected to my Asus HD7970-DC2T video card, using the Dual link DVI cable provided with my monitor.

  Unfortunately, I can't set my resolution of 2560 x 1440.

  Only I get to the resolution is 1920 x 1080

  I tried the two DVI ports on my video card (with a reboot after changes), installed the driver from Dell for the monitor, researched internet if it is possible to set the maximum using DVI resolution (must be determined according to the time the Dell website and specifications of my video card).

  So, any help would be much appreciated.

  Video card: http://www.asus.com/Graphics_Cards/HD7970DC2T3GD5/

  In the end, I managed to solve my problem.

  After a lot of searching on the internet, I found that the mentioned video card has a little switch that decides one of the DVI ports is to double bond or not.

  So I turned off my pc, open the computercase, flipped the switch, rebooted the system and there it was: 2560 x 1440

  The mentioned switch position can be seen in the image below:

  

  I hope that this will help people who runs into the same problem.

• DisplayPort U2713HM frustrating problem

  I just got a new Dell U2713HM monitor and tried to connect it via cable DisplayPort 1.2 from a PC brand new.

  The monitor says "No DVI not connected" and enters a power saving Mode.

  Symptoms:

  1 connect only DP of PC from Dell U2713HM-> monitor goes into power saving (and on no detected DVI companing) Mode

  2. connect only Dell U2713HM-> DVI monitor to the PC up to 1920 X 1080 display resolution (not enough and clumsy to be honest)

  3 - connect the DP and DVI simultaneously - monitor behaves strangely. He blows a small portion of the screen, so you can't see the other parts of the screen. I can see the mouse moving through. Right-click on the screen and go "Screen Resolution" displays a maximum resolution of 2560 X 1440, but I get to use it and it does not change this mode of supply.

  This seems to be a problem in the new range of Dell of whose very disappointing for this superb rather monitor.

  No idea how to solve this problem?

  I have corrected the problem. In fact, it was not a problem, but rather a configuration problem.

  Go to Dell menu and set the display Port input source (it is not detected automatically)

• Screen resolution problem. Cannot set above 680 x 480.

  Screen resolution problem

  I have a dell latitude d630 2.5 GHz computer laptop under XP Professional 64-bit operating system.  The screen resolution will not be set above 680 x 480, and when I try to increase the computer stops with a black screen message that don't stay long enough onscreen to read.  Dell advised that they don't or support this machine with the XP operating system and that they have no drivers or other fixes for the problem.  I hope that you will be able to help and thank you.

  Hi dduck11,

  ·         What is the default screen of the laptop resolution?

  You need to update the graphics (video) drivers for the laptop. I see that there are Windows XP drivers available for the same thing. Download and install the updated drivers to see if it helps.

  Drivers & downloads for Latitude D630

• resolution problem with my monitor every time I turn on

  I have a monitor to display wide w1907 h p on nvidia gforce7050/nvidia nforce 6101.2 weeks I had restore the desktop pc top of page back to default settings since then every time I turn on the screen starts to the resolution of the game and then after a few seconds, it turns into the resolution.i minimum re on this return to the recommended resolution and it stops on this setting until I have put it off and then when I use the PC again I have to repeat the process thanks t..

  Hi Tony,.

  Have you checked that you have the correct nvidia gforce drivers installed from the manufacturers Web site?
  This problem may appear when you have a general driver for the graphics card.

  You could try reinstalling the drivers for the graphics card because it could have been corrupted somehow when return you to the default settings.

  Kind regards

  Joel

• Hi, I just upgraded my 4s to 9.3.2 and now it is completely dead and will not start. Had no problem with any other previous updates.

  Hi, I just upgraded my 4s to 9.3.2 and now it is completely dead and will not start. Had no problem with any other previous updates.

  Sorted now

• Satellite C70 - A - 16 L - screen resolution problem

  Hello

  I recently had a screen resolution problem with my laptop (C70 - A - 16 L).
  The max screen resolution which is imparted to me is 1366 x 768, whereas before I think he used 1600 x 900.

  I tried the latest drivers, Bios, etc. and have also restored the operating system to a previous backup, as well as a new installation.
  I also tried to roll back to Windows 7 (with proper drivers). They all offer the same problem.

  This new maximum resolution display correctly - as if the LCD does not deal with the timings of 1366 x 768.
  I believe that the Panel is OK and the problem he reports the EDID information properly - to force windows to use the new resolution.

  Is there a download monitor.inf file that can be used to bypass the EDID reported by the Panel?

  Kind regards

  Antwist.

  If the right to display drver is usually installed everything should be OK.
  Have you installed Intel driver Toshiba download page 9.17.10.3062 version?

• Go off & on several times before the monitor turns on. Comp seems to start OK but the problem is with the screen.

  Original title: XP start help please...

  ... are to be turned off & on several times before monitor lights. Comp seems to start OK but the problem is with the screen. Do I have to make a boot disk & if so - HOW?

  Hello

  ·         What is the brand and model of the computer?

  ·         You get the error message?

  ·         Did you check the connection of the cable to the monitor?

  ·         Have you tried to update to the latest graphics card and motherboard chipset drivers?

  First, try to connect your monitor to a well known PC, maybe the old laptop that you use now. If the monitor works, the problem is with the video card in your PC. If the monitor does not light, the monitor. It is usually cheaper to buy a new monitor that in order to be an old repaired, unless the monitor is still under warranty.

  Try connecting a monitor well known to your PC. If the monitor works, your old monitor is fried and needs to be replaced.

  If your monitor works when connected to another PC, the problem could be your video card. First, and then you turn on your PC, the power and cooling case fans run they. If they do not, it could be the power supply.

  Then, open the computer case. Before you do anything inside, unplug the power supply.

  IMPORTANT! Touch any metal part of the computer case to connect to the PC. A single static spark can destroy computer circuits.

  If the video card is the type of card that plugs into a slot on the motherboard, remove the screws or attached at the top of the card, remove the card, to manipulate the card by the edges to avoid disturbing the circuits on the card, carefully and re - install the card. Sometimes simply reinstalling the card corrects the problem.

  If this does not work, replace the video card with a card of similar type. Perhaps now is the right time for an update of video card.

  If the video card is integrated into the motherboard, you can install a new card in one of the PCI slots on the motherboard. When the PC starts for the first time, go into the bios and disable the onboard video.

  Resources for troubleshooting problems in Windows XP

  http://support.Microsoft.com/kb/307960

• Why start having internet connection problems when I watch a lot of videos in windows vista?

  Why start having internet connection problems when I watch a lot of videos in windows vista?

  Bandwidth saturation, perhaps?

• Start of updates causing problems

  Hello

  I have a vista operating system.

  Since a few months now whenever windows installs an update on my computer, the next time I go to start it it refuses to do.

  So I changed the settings to make sure it didn't install anything without anything to say then, but for some reason that the computer keeps deciding to change these settings on it installs and own agreement anyway. Which means that every week or two my computer will not start again. These problems occur only when it installs the microsoft windows updates that are not security ones or curiously Java.

  Anyone has an idea why it continues to be and how to stop it because it's getting pretty boring.

  Thank you.

  Java has its own update system, it does not use Windows Updates settings.  Open the Java Control Panel in the control panel to configure updates.  Probably something similar happens with other products you have to check their update setting.

  "Maxi_Jay" wrote in the new message: * e-mail address is removed from the privacy... *

  Hello

  I have a vista operating system.

  Since a few months now whenever windows installs an update on my computer, the next time I go to start it it refuses to do.

  So I changed the settings to make sure it didn't install anything without anything to say then, but for some reason that the computer keeps deciding to change these settings on it installs and own agreement anyway. Which means that every week or two my computer will not start again. These problems occur only when it installs the microsoft windows updates that are not security ones or curiously Java.

  Anyone has an idea why it continues to be and how to stop it because it's getting pretty boring.

  Thank you.

• Animation starts in low resolution after editing with 'Air Desktop Embedded LENGTH 20'

  The test of my animation of inside film CC animate using 'Control -' Test', it launches high resolution and works very well.

  After having published 'Air 20 desktop', "Application with the Runtime shipped", it works well but starts in low resolution and I can't change it!

  'Get Info' has the box "Open in a low-resolution" checked and grayed out.

  How to set the animation to begin in high resolution (preferred option) or change it once running?

  Kind regards

  EM.

  There is an XML file in the publication. It will be named something like MyApp - App.Xml. Which open in a text editor and add the line to the section of the initialWindow.

• Screen resolution problems (Windows 10)

  I downloaded the latest trial 9 Captivate for Windows 10 and screen resolution problems. Basically, making the software unusable. A lot of screens and dialog boxes seems larger than the current window, they are in, making the right and downstairs parts invisible window (usually, this is where the 'OK' and 'Cancel' buttons for example).

  I'm Captivate on a laptop running 64-bit Windows 10 (Sony Vaio with an NVidia GT 640 M map graphic with the latest drivers)

  Does anyone know how to fix this? Here are some examples:

  

  

  

  No retina.

  What is the size of the police on? Win10, it is often larger than 100%, which is not really necessary for your resolution, but that's a retina display. I am using Captivate on Win10, but Surface Pro and laptop have a retina display.

• Hi, when I click on the blue arrow on my widget options, its not letting me see everything cos its too big. and I can't scroll upwards or downwards to see the options. It might be a resolution problem do not know. Help.

  Hi, when I click on the blue arrow on my widget options, its not letting me see everything cos its too big. and I can't scroll upwards or downwards to see the options. It might be a resolution problem do not know. Help.

  Hello

  Have you tried to rename the folder Preferences for Muse.

  Nearby Muse > GB appdada % in windows explore > rename the folder named as com.adobe.AdobeMuseCC.2014.3 in com.adobe.AdobeMuseCC.2014.3_old.

  Concerning

  Vivek