Static ARP entry telnet command - techies check pls!

Similar Questions

• -an ARP entries

  Hello

  I have a quite a beginner. The following were - an arp entries. I know that the first three topics are the ones I put in place. What are the others? How to find based on three MAC address? RSV4000 is my router.

  Interface: 192.168.1.108 - 0xc
  Internet address physical address type
  192.168.1.1 xx-xx-xx-xx-xx-xx Dynamics
  192.168.1.100 xx-xx-xx-xx-xx-xx Dynamics
  192.168.1.104 xx-xx-xx-xx-xx-xx Dynamics
  192.168.1.255 ff-ff-ff-ff-ff-ff static
  224.0.0.22 01-00-5e-00-00-16 static
  224.0.0.252 01-00-5e-00-00-fc static
  239.255.255.250 01-00-5e-7f-ff-fa static
  255.255.255.255 ff-ff-ff-ff-ff-ff static

  Thank you.

  Well, if you are a beginner, don't play with arp.

  These are all standard arp entries, indicated by "static", meaning that they are predefined.

  192.168.1.255 255.255.255.255 match LAN broadcast IP addresses. They are mapped to the dissemination ff-ff-ff-ff-ff-ff ethernet address.

  224.0.0.22 and 224.0.0.252 are used for IGMP/multicasts, mapped to the corresponding ethernet addresses.

  239.255.255.250 is used for the SSDP/UPnP protocol.

• Bar is not signed RDK bar isn't signed AUTHOR this bar contains unsigned entries that did not check integrity.

  I created an application with qt creator, it works very well on my z10. But when I download the bar file to blackberry, I got this message

  "Bar is not signed RDK bar isn't signed AUTHOR this bar contains unsigned entries that did not check integrity.". "

  I am registered already BlackBerry signing authority and I also have a debug_token.

  The qt project has to a file of bar - descriptor.xml, information of the author are the debugging token.

  Can someone tell me how I can solve this problem?

  Problem solved.

  use the following two command lines

  BlackBerry XXXXX.bar bar-descriptor-XXXXXX-qtc-nativepackager-package - generated.xml

  BlackBerry-sign - storepass yourstorepass XXXXXX.bar

• How to create a static ARP using SNMP?

  Hello

  I want to create a static ARP using SNMP.

  I can delete an ARP by setting oid ' 1.3.6.1.2.1.4.22.1.4' to '2'.

  But none of

  '1.3.6.1.2.1.4.22.1.1 '.

  '1.3.6.1.2.1.4.22.1.2 '.

  '1.3.6.1.2.1.4.22.1.3 '.

  '1.3.6.1.2.1.4.22.1.4 '.

  can be modified or created

  SNMP-server community is RW

  I can change the other oid, for example 'type sysName' oid 1.3.6.1.2.1.1.5.0

  I used this command to create a new ARP:

  set SNMP v2 192.168.10.1 private oid 1.3.6.1.2.1.4.22.1.1 integer 1

  the answer:

  SNMP response: reqid 16, errstat 11, erridx 1

  ipNetToMediaEntry.1 = 1

  errstat 11 is NOCREATION

  And I used the tool "Mib Browser" to set a static ARP.

  the answer is NOCREATION too.

  I searched a lot of time, a lot of people have this problem,

  someone said the oid ipNetToPhysicalPhysAddress or inetCidrRouteTable is alternative,

  but our switch do not have these oids.

  I can't find a solution.

  I want to know if the task can be performed.

  Help, please.

  Concerning

  Dear Fu

  Thank you to reach small business support community.

  I'm not positive, that this can be done on small business goes, however, what is your version of the model and the firmware of the switch so I can continue the investigation.

  I'll be looking forward to your reply.

  Kind regards

  Jeffrey Rodriguez S... : | :. : | :.
  Support Engineer Cisco client

  * Please rate the Post so other will know when an answer has been found.

• [Can't press Ctrl +] to the telnet command, it doesn't seem to work?

  [Can't press Ctrl +] to the telnet command, it doesn't seem to work?

  Hello

  1. have you made changes on the computer before this problem?

  2. the computer is on a domain network?

  Follow these steps to escape the Telnet connection.

  a. to start a Telnet session
  b, click the Start button, click Run, and type command prompt.

  c. type telnet {destination or IP address}

  [(d) in order to escape the Telnet connection, type Ctrl +].

  Also, please provide an explanation more detailed of how you try to get the command works and what you expect to happen.

• command to check the tablespace is read or write mode State?

  command to check the tablespace is read or write mode State?

  SELECT status FROM dba_tablespaces WHERE nom_tablespace = 'MY_TS ';

  The State values are online, offline, or READ only. ONLINE is READ WRITE.

  HTH,

  Brian

• command to check the level of patch of OIM 11 g R2

  Hello
  
  Could if it you please let me know the command to check the current patch of OIM 11 g R2.
  
  Please also let me know the steps to run this command.
  
  Thank you

  Export ORACLE_HOME = / opt/oracle/middleware/oracle_idm1
  $ORACLE_HOME/OPatch/OPatch lsinventory

  -Kevin

• Command to check vmnic driver

  I've been on with the support of a few weeks there is a problem and we understood that part of the problem may be due to updated drivers vmnic.  I already have two guests day and I have the patch bundle on one of data warehouses and I have control to install the update, but I don't remember the command to check the driver information.  I "think" it's an ethtool command, but I'm not 100% sure.  Is someone can please help me remember the command?

  The command to check the drivers for your network card is:

  ethtool-i vmnic0

  Best regards, Robert

  Post edited by: RvdNieuwendijk

  Changed typo.

• VPN client and contradictory static NAT entries

  Hello, we have a VPN IPSEC implemented on a router for remote access. It works very well, for the most part. We have also a few PAT static entries to allow access to a web server, etc. from the outside. We deny NATting from the range of IP addresses for the range of VPN client and it works except for entries that also have PAT configurations.

  So, for example, we have web server 10.0.0.1 and a PAT redirection port 10.0.0.1: 80 to the IP WAN port 80. If a VPN client tries to connect to 10.0.0.1: 80, the syn - ack packet back to the customer WAN IP VPN on the router! If the VPN client connects to the RDP server 10.0.0.2:3389, it works very well that this server is not a static entry PAT.

  Is there a way to get around this?

  Thank you!

  There is a way to get around, use the same settings you have for your dynamic nat in your nat staitc entries, something like this:

  Currently, it should show as:

  IP nat inside source static XXXXX XXXX 80 80

  you need to take it

  IP nat inside source static 80 XXXX XXXX 80 map route AAAA

  When your itinerary map YYY refers to something with an acl that you refuse traffic from inside your router for the pool of vpn

  IP Access-list ext nonat

  deny ip 10.0.0.0 0.0.0.255

  Licensing ip 10.0.0.0 0.0.0.255 any

  route allowed AAAA 10 map

  match ip address sheep

  You even need all the static PAT

  HTH

  Ivan

• Command to check the tunnel VPN S2S awhile in the cisco router

  Dear all,

  Please share the command check S2S tunnel of time that is configured on the router.

  There are commands that define the lifetimes of (his) IPSec Security Associations, ISAKMP.

  For example:

  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  life 3600

  life 3599 seconds crypto ipsec security association

  ... and you can determine the remaining lifetime for these SAs with the following commands:

  SH detail session crypto

  SH in detail its crypto isakmp

  SH crypto ipsec his

  The delta between the lifetime (s) configured and remaining life will tell you how much time has passed since the last regeneration, but that is as close you are likely to have to determine when the tunnel came first.

  You could use other means as States of syslog for you say when a Tunnel is a transitioning upwards or downwards.

  Best regards

  Mike

• ESXi 6.0 - SSH Command to check the status of running tasks

  Hi all

  What I'm trying to do is quite simple, but do not know whether it is complex or not.

  I'm checking the State of a task via SSH. You know, like that of the lower part of the vSphere Client where it shows you the task and the status of it. I need to monitor the % of the deployment of the MV EGGS in various hosts via a script but can't find the command to do, but would be nice to be able to check any task and its status.

  What I found so far:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1013003

  But that was not helpful at all. I tried but could not get information about the deployment.

  Thank you all for any help or lead, you may have.

  Hello world

  I found the answer myself, which was indeed in the URL I posted.

  I just had a problem to see a small change in orders.

  In step 7, it says task_info and I wrote get.tasklist with the task identifier.

  Thank you guys and I hope at least that it might help someone trying to do what I'm doing and reading VERY well orders, haha

  Kind regards

  Martin

• How a router via the Telnet command file

  Dear boss

  I have a few remote cisco router and have telnet access to the router (172.16.1.1, 172.16.2.1...). I want to add a route to the router through a windows batch file. How do I? Please help me with the sample.

  Thanking you

  Shahid

  Hey Shahid,

  The issue of Windows XP, you have posted is better suited for the IT Pro TechNet public. Please post your question in the

  TechNet Script Center for assistance.

  Hope the helps of information.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• How to disable the command CHKDSK - Check Disk start up for Windows 7

  I have some problems, when I start my laptop I am prompted with a black screen saying

  

  I found no solutions on how to disable this on my computer, but I want to because after the seconds say 1, its stays for a while... and I've left on during some time, the screen is still asleep when I turn... The page is black... Can someone help me to disable the calendar checking for windows 7? Thank you very much! : D

  Hi PikaBrian,

  Welcome to the Microsoft Answers site!

  To disable automatic disk checking at the start of Windows through registry, go to the following registry key:

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 how to back up and restore the registry in Windows: http://support.microsoft.com/kb/322756

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Session Manager

  In the right pane, double click BootExecute.

  The default value of the key is autocheck autochk *

  * means that each drive is checked for consistency. Just add /K:C to the end before *. /K switch will disable autocheck on C: drive at Windows startup. If the final value should look like this:

  / k: C to autocheck autochk *.

  If you want to add more drives, the key should look like this: (by disabling the drives C and D)

  / k: D / k: C autocheck autochk *.

  If you want to restore all default, just replace the key with the default i.e.

  autocheck autochk *.

  You can also follow the link given below and check if it is of no help.

  http://social.answers.Microsoft.com/forums/en-us/vistaperformance/thread/a8ab415b-4559-45C6-99a4-a54e27e5a836

   

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• What is the command to check ASM disk space

  Hello guys of ASM.
  
  Can someone tell me how to check the disk of the ASM is available, occasion etc... amount of space between the views of data.
  
  Thank you, Mitra

  Use it to exact query

  Select name, total_mb, free_mb, usable_file_mb, round ((total_mb-usable_file_mb) / (total_mb) * 100, 0) pct_used v$ asm_diskgroup

  Kind regards
  Dominique Piron

• N2000 - arp with Enhanced hash mode issues

  Hello

  I want to report a problem, I got after pass a set of three switches the 6.2.6.6 version N2048 to version 6.3.0.16

  After the upgrade, some PC on some VLANs failed their gateway more. I found that these devices don't y mac of the bridge in their arp table. It would seem that their arp requests would be removed in the channel port connecting the N2048 to the rest of the network stack. Add a static arp entry on the affected PC has enabled them to reach their front door.

  I know that there has been a bug (fixed in 6.3.15) with package falls on the port channels using the (strengthened) 7 mode. It gave me a clue and today I changed the mode of hash for 6 (IP Source/Destination and source/destination port TCP/UDP) and I removed the static arp entries, that I had created to circumvent the problem of the day before. Then I could see the bridge as a dynamic desktop entries, as it should.

  It seems that there is always a with improved hash bug in 6.3.0.16. I'll be happy to send my config and / or more information on demand to help you study the problem.

  Kind regards

  Martin

  cool, which is literally just released although there was a lot of outings lately.

  See you soon

  Jamie