Store full of internal data in the file "Blah blah" format.

Similar Questions

• Write delay failed unable to save all the data for the file $Mft

  Have a frustrating problem.  Help is greatly appreciated.  Learned the hard way and lost a dwg important issue which was unrecoverable.  Bought a new drive external hard seagate.  Could not back up the entire system with software pre-installed.  Download acronis true image home 2011.  Tried to backup system.  Receive error when trying to backup messages; 'Delay to failure of Scripture; Reading of the sector; Windows was unable to save all the data for the file $Mft. The data has been lost.  Have tried many fixes.  Unable to disable write caching method (grayed out / unclickable).  Played regedit 'EnableOplocks' is not listed to select.  Attempted to run microsoft 'fix it' and got the blue screen of death.  Short hair out of my head.  Suggestions appreciated.

  I don't know where Microsoft 'Technical support engineers' get their information.

  Write caching without a doubt "does apply to external hard drives", but it is usually disabled to prevent to sort the problem you are experiencing.

  I've seen several positions reporting to the same question that you do.  All of these positions were with SATA drives.  Is your Seagate eSATA drive?

  The disc is recognized as an external drive in Device Manager?  In Device Manager, go to the drive properties dialog box and click the policies tab.  An external drive should have two options: "Optimize for quick removal" and "Optimize for performance".  An internal hard drive shows the options as gray (with 'performance' selected), but there should also be a checkbox "Enable disk write cache" under the second option.

  What shows in your policies tab?

  If I understand correctly, "writeback" or "write behind" is implemented by disc material or its pilot.  If the option is not available on the drive properties > policies tab, I would suggest to contact Seagate support.

• Why Lightroom does not change the creation date of the file? (Mac OS)

  I find that Lightroom changes the creation of files present during the incorporation of metadata. I noticed that this behavior is different from the bridge, which reaches to write metadata changes to the file without affecting the creation date, affecting only the modification date.

  I read in other threads that it doesn't matter when even because moving files between disks will write a new file and, therefore, a new date of creation, but if this can be true in some systems (I don't know) is certainly not the case with Mac OS. For example, I have files dating back at least 1998 which have been moved from disc to disc to disc but still retain their original creation date. Which is as it should be. For many of my older images, there seems to be no capture embedded recognizable don't date anyway, so the creation date of the file is the single timestamp.

  It seems quite logical that the modified date of a file must be updated to take into account that the file has been modified (for example if adding metadata), but it seems to make sense that the date of creation of the file should be kept as the date, this file has been created. Changing them both on the same date seems to be a needless loss of information.

  Some would say that the process of adding metadata to a file creates a new file, the creation date must be updated to reflect this. But I would say that the creation date should be which would include a normal user as the creation date. We do not expect the creation date to change everything simply because a file is rewritten to the disk (for example when the defragmentation), however technically accurate, it would be to say that it is a newly created file. And the difference in behavior between Bridge and Lightroom shows that there is some confusion on this subject.

  Photo software ignores generally the operating system created by file-modification dates, and when he is not ignoring them, treated generally in a non-standard way that varies from one program to a program.  Rather than rely on the dates of the files of the operating system, the photo industry has defined fields of metadata with all sorts of specific photos dates: capture date/time (when the shutter button is depressed), date/time of scanning (when a movie or a print image was scanned digitally), date/time software photo altered image or metadata date/time of GPS location.   While some photo software will attempt to maintain the dates of file-created and - updated, many programs and services Web will not (including, but not limited to, LR).  In addition, many utilities files not always to preserve created and set dates to day that you move, copy it, backup and restore files.

  Therefore, I highly recommend that if you care photo dates and times (as I do), so no matter which photo software you use, you store the dates of capture in pictures industry standard metadata by using the tools provided by LR and other photo software.   In this way, you migrate the program to the program over the years, are you more likely to preserve that important metadata.

  Old photos and scans without that metadata, when you first import into LR, LR will assume that the capture time is the hour of the modified file.  LR to rewrite the date of capture of metadata in the file by selecting and making the metadata you can do > edit Capture time, clicking OK and then by metadata > save metadata to file. You can do it in batch - choose all your old photos and make metadata > edit Capture time, click OK, to metadata > save metadata to file.  LR will affect its time updated each file capture time.   If you want to set the time captured in the file create time, select this option in the window change the Capture time before clicking OK.  But beware that many Windows and Mac file utilities cannot preserve create time, even if they retain changed time, in order to create your files time can be wrong.   And of course, make sure that your backups are up to date and valid before making any new procedure file with which you aren't familiar.

  But if you really want to use non-standard file dates to keep your metadata information, and you want Adobe to modify accordingly the LR, so please give your opinion and vote on it in the Adobe official feedback forum: Bug report: Lightroom modifies the image files creation date. This forum is a user forum in which is rarely involved Adobe, Adobe said they read every post in the forum comments (and sometimes they respond).

• Read data from the file into ArrayList

  Hello
  I have a class called product describing the charactristics of products such as the name, id, price etc.. I have the whole set and use the get methods in my class of product. I store the information on my products in an ArrayList. I can write the information on my products in a file.
  so far, but so good...
  
  I want now to re-read the data from the file and store it in my list of tables again. I know I can use Parsing and read in data in an ArrayList as String, int, double etc. but is anyway to read in from 'Product' (then it would be up to my class of product)?
  
  Thank you in advance.

  1. are you aware of serialization?
  2. get a name, I love not dealing with numbers.

  DB

• write table 2D data in the file but the file is empty

  Hello

  I tried to write all reading of powermeter data to a file in two ways, I can see the output in the Arrais indicator data but when I write to "File.vi of the worksheet" or write to 'text file', the files are empty.

  Please help me.

  Try to remove the vi "STOP".

  I suspect, it prevents the main vi before the backup occurs.

  As a second point: given that you save data inside a while loop be sure you add the data from the file and not crash each time.

  wire that is a 'real' terminal 'Add file '.

  Kind regards

  Marco

• LabVIEW backup only 2 seconds of data in the file

  Sorry for this question of beginner, but after a few hours of searching for an answer and trying to solve the problem, I still can't understand.

  I use a DAQ Assistant vi, displaying the data on a chart in waveform, and to help to write it into a file as vi to try to save the data I collect (this is a while loop). A .tdm file is created successfully, but only about 2 seconds of data (25 k samples) are saved in the file. In addition, I write custom vi set to 'Add '.

  I need to save the data for the duration of my collection (between 2-20 min).

  I'm sure the solution is brutally simple, but any help would be greatly appreciated.

  Thank you!

  surffl wrote:

  Yes, I use the importer of CT in OpenOffice as provided for by the regulation.

  Do you trust to OpenOffice?  What do you get when you use the importer with MS Office?  I don't think you have a problem with your VI, but a problem with the importing program.  LabVIEW is certainly save more than 1 second of data in the file.  I thought that after each section headers might have caused and the file reading problem, but if you say settting it only write a header still causes problems with importing the data, I think that the problem comes from the importer.

• Best way to record 50 kech. / s data to the file

  I'm reading a data acquisition data at a sample rate of 50 kech. / s and save it in a file. My application must run for at least a few hours. At first, I tried a model of loop of consumer-producer with a writing on measurement file Express VI, but he wrote the data too slowly, and my queue. Now, I'm trying to use the Write to VI file spreadsheet with or without a loop of producer-consumer model (see attached screws). Both seem to write data to the file, but no written records the number of datapoints I expect (the two have a lot less datapoints).

  What is the best way to write data to the file? Seems like a basic question, so if it has already been discussed in detail in another forum, or if there are examples of what someone could point me to, that would be appreciated also.

  Thank you!

  Hvea look at "stream directly to disk with TDMS in LabVIEW".

• How can I write snapshot of my data to the file measured every 5 seconds

  Hello

  I try to take a snapshot of my stream once every 5 seconds and write it to a. File LVM. I have problems with the VI "write to a measurement file. The pace at which it writes data to the file seems to be dictated by the 'Samples to Read' parameter in the DAQ assistant. I tried placing the VI 'Write in a file measure' within a business structure and the launch of the structure to deal with a "time up" VI. As a result only in a delay of 5 seconds before the insiders 'Write in a file as' VI. Once the VI 'Write in a file as' is launched, it starts writing at 20 x per second. Is there a way to change it or dictate how fast the exicutes VI 'Write in a file measure'?

  My reason for slowing down the write speed are, 1) reduce space occupied by my data file. (2) reduce the cycles of CPU use and disk access.

  The reason why I can't increase the value of 'Samples to Read' in the DAQ Assistant (to match my requirement to write data), it's that my VI will start to Miss events and triggers.

  I don't know I can't be the only person who needs high-frequency data acquisition and low-frequency writing data on the disk? However, I see a straight road to key in before that.

  The equipment I use is a NI USB DAQ 6008, data acquisition analog voltage to 100 Hz.

  Thanks in advance for your help

  See you soon

  Kim

  Dohhh!

  The re - set feature has not been put in time elapsed VI!

  Thank you very much!

  See you soon

  Kim

• How can I change the creation date of the file through Labview 2012?

  I want to change the format of the data stored in text files, but I want the dates of the files to stay the same.  Currently, my program creates files with the new dates.

  LabVIEW to my knowledge has no native functions to do.

  You can use functions to get/set CreationTime, LastAccessTime and LastWriteTime .NET on Windows.

  See attached VI (LabVIEW 8.6)

• Error message on Windows XP, "Windows-Delayed Write failed, windows was unable to save all the data for the file.

  I use windows xp as the operating system. I bought the new 3G huawei data card. While surfing internet, between a pop-up is displayed

  «Windows-delayed write failed, windows was unable to save all data in the file C:\Documents and settings\new\Local Settings\Application Data\Google\Chrome\User Data\Default\Session Storage\004285.log.» The data has been lost. This error can be caused by a failure of your computer hardware.

  After this computer freezes and I have to restart my computer. Please help me how to fix this problem.

  The error basically says that he tried to write something on your hard drive and for some reason that unfinished write operation.  This could indicate a bad sector on your hard disk, damaged disk or a problem with your hardware.

  Whenever a problem involving a disk read or write appears, my first approach is to perform a verify operation of the disc to the hard drive.  Even if this is not your problem, it is a step of good routine maintenance. Run the disk check with the "/ R" or "Repair" option.  Note that the real disk check will be presented at the next reboot, will run until Windows loads completely, cannot be interrupted and can take more than a few hours to run depending on the size of your hard drive, the quantity and type found corruption and other factors.   It is better to perform during the night or when you won't need your computer for several hours.

  'How to perform disk in Windows XP error Cherking'

  <>http://support.Microsoft.com/kb/315265/en-us >

  HTH,

  JW

• Access to the data in the file permissions

  I have a html file that is generated by a third-party application.
  I want to give only the permissions to write data in the file, I don't want to give permissions to remove content.
  (it's not the file's content in the file)
  How can I put it please suggest me.

  As I said...  I don't think that what you want is possible.
  If someone can write (Edit) a file, then it can also remove all the contents of this file.

  It seems to me that you are looking for a software revision control... something that helps other people to make changes to a [copy of a] set of files, but gives a control authority the word to say as to when and if changes go in the direct copy.  It also regression to an earlier point in time.

  "Comparison of revision control software.
   <>http://en.Wikipedia.org/wiki/Comparison_of_revision_control_software >

  HTH,
  JW

• How to use the date of the file, when you download a file?

  Using the basics of 12 c, APEX 5.0 and IE11

  I am creating a file upload feature for my application.  I'm able to get the upload├⌐ file in my table, but one of my requirements is that I fill in a value in the table with the "file date".

  Is there an easy way to get the "file date" in the file being downloaded and fill a field for all records with this date?

  Tillie

  Tillie says:

  Using the basics of 12 c, APEX 5.0 and IE11

  I am creating a file upload feature for my application.  I'm able to get the upload├⌐ file in my table, but one of my requirements is that I fill in a value in the table with the "file date".

  Is there an easy way to get the "file date" in the file being downloaded and fill a field for all records with this date?

  That depends on your definition of 'easy '...

  The HTML5 File interface can be used to access date in browsers supportthe file was last modified.

  1. Add a hidden page that contains the file download point (P6_FILE_DATE in this example).

  2. create a dynamic action of change on the file upload question (P6_FILE):

  Event: Change

  Selection type: Agenda

  Region:

  Real Actions

  Action: Run the JavaScript Code

  Fire on Page load: NO.

  Code

  console.log('Get file modification date:')
  var fileItem = $x('P6_FILE');
  if (window.File) {
    if (fileItem.files.length > 0) {
      var file = fileItem.files[0];
      if (typeof file.lastModifiedDate !== 'undefined') {
        console.log('...lastModifiedDate for file \"' + file.name + '\": ' + file.lastModifiedDate);
        apex.item('P6_FILE_DATE').setValue(file.lastModifiedDate);
      }
      else {
        console.log('...browser does not support the HTML5 File lastModifiedDate property.');
      }
    }
  }
  else {
    console.log('...browser does not support the HTML5 File interface.');
  }
  

  If the browser has support for the File interface and lastModifiedDate property, the date, the file was last modified will be presented in the P6_FILE_DATE article in the form:

  Fri Jul 17 2015 10:43:44 GMT+0100 (GMT Daylight Time)

  You can analyze and convert your data load process to obtain a TIMESTAMP or DATE value according to the needs.

• Issue while loading data using the file Rules Essbase

  Hi all

  I am facing problem while loading data using the Rules file. In the rules file, I rejected several members in two areas (two dimensions). Now if I load the data using the rules file I'm getting errors for all members in the dataload.err file. If I reject mutiple members of a single field, the data load without settling errors in the dataload.err file.

  I want to know how rmany members of several fields of ejection for loading data using the file Rules Essbase? Is it possible?

  Okay, okay... I think that you must assign Global Select / reject Boolean in the parameters of loading data as 'Or':

  

• I have problems with anchors named in my htm file. I clearly identify them as being in the document (ie., internal links within the file).  When I preview the file in a browser, the links point to my hard drive, which is totally false. What do I need

  I have problems with anchors named in my htm file. I clearly identify them as being in the document (ie., internal links within the file).  When I preview the file in a browser, the links point to my hard drive, which is totally false. What should I do to change it?  I use DreamWeaver 2004 on a PC.

  You will need to correct the links that begin with "file".

  Now that your site has been defined, you just delete the bad links and DW left write the good ones for you.

  Click on the yellow folder on the property inspector, and then select the target page.

  

  If your site is small, you can edit the links manually (remove the part in red)

  content.htm file:///C:/desktop/localRootFolder/subfolder/subfolder/images/

  It would be useful that post you your code on the page so that we can see if you use the old technique or new for these links.

• "Scratch disk" was almost full attention. I deleted the files opened to create space. However, photoshop CC, crashed before that I was able to free up space. I tried several times to re - open Photoshop CC but within 2 seconds it crashes when loading. I t

  "Disk zero" was almost full warning. I deleted the files opened to create space. However, photoshop CC, crashed before that I was able to free up space. I tried several times to re - open Photoshop CC but within 2 seconds it crashes when loading. I then decided to upgrade to the 2014 version, update. He worked twice and now repeat the same problem, I have lived before update. This only happens when I'am connected under "other user account" as I had been when the accident happened first and not as an administrator. I purged the cache, more space for performance, etc. in Admin mode, I ran permission repair in public services, but when I change the user account, photoshop crashes with seconds loading. Please notify 2.8 GHz Intel Core i7, 8 GB 1600 MHz DDR3

  As you can already read in your crash report - the crash has little to do with Photoshop and everything to do with your Nik/Google SelectiveTool plugin.

  Disable this plugin and contact Nik/Google for an update that fixes bugs in this plugin.