Stream network between end myRIO PC

Similar Questions

• Visa name cluster resource to the stream network writer causes error 42.

  If I try and pass this heap of 'data engine' with a VISA embedded resource name:

  

  for a Writer of stream network in this way:

  

  Then I get this error of the VI "write only to flow."

  

  If I change the data engines TypDef cluster so that a chain control is used instead of the VISA reference, the error disappears and data crosses the stream network without problem.

  

  This is expected behavior?

  I thought that the 'data' (type = "POLY"?) as one located on the VI 'Write one element to flow' was supposed to take just about anything...

  Hi Rolf and WNM,

  After further investigation, I was able to reproduce the problem and agree that it is a bug. This was reported to R & D (#395047) for further investigations. As mentioned previously, a possible workaround is using the address of the cluster instead of the resource VISA VISA. Thanks for the comments!

  Doug W

• Home network between 2 computers by LAN does not.

  I am trying to establish a network between 2 computers per LAN. They are in the same workgroup and I see each computer on the other computer. When I try and open or use of disks from one computer to another, I get 2 messages. 1. you don't have administrator rights. 2. this drive is not accessible. I used the wizard of network at home several times without success. Both computers have Windows XP. ????? Is there an easier way?

  Robbo,

  You can visit the pages below:
  http://www.duxcw.com/FAQ/network/xpshare.htm
  http://support.Microsoft.com/kb/304040
  See you soon ~!

• Configure a wireless network between 2 computers

  Original title: How can I set up a network between 2 computers

  I would like to set up a network between my woman computer and my laptop can we establish a wireless connection with a wireless router.

  Hello

  Click on the link below.

  Establishment of a network (Vista) wireless

  Hope this information helps.

• Home networking between Vista & Win7

  I'm trying to access a printer (hosted on a machine to Vista o/s) of an o/s Win7 machine on my home network.  Is networking between these two operating systems feasible?

  Yes.  These web pages have the details to help you implement:

  Sharing files and printers with different versions of Windows
  Networking of computers running different versions of Windows

  Boulder computer Maven
  Most Microsoft Valuable Professional

• Need help to set up a network between two Windows 7 computers

  I have two Windows 7 computers at home: one is a desktop computer that is connected directly to the internet (with a network cable), and the other is a laptop computer that is not directly connected to the internet with a network cable.  We have a configuration of wireless network for your laptop is set up of this network and has internet access.

  What I want to do is set up a network between the two of them, so that the laptop can access the printer that is directly connected to the desktop computer.  I got this configuration when both computers are Windows XP, but since we their past to Windows 7 I can not it works.  I tried to create a home network, I set the printer on sharable and given him a name, but I can't access it on the laptop.

  The printer is actually a photocopier, but it is directly connected to the desktop computer.  In fact, it is connected to the router than the phone company provided.  But we want the laptop to be able to access it and use it.  As I said, we had this configuration when these computers are computers Windows XP, but I tried following the instructions to do this for Windows 7 and I can't make it work.

  Also, I'm not that computer savy, so please if you tell me to run a program it please tell me how to find and launch this program.

  Thanks for any help.

  Hello

  Welcome to the Microsoft Community Forum.

  Before you start with the troubleshooting steps, I would need some information on the subject, so that we can better help you.

  1. What happens exactly when you try to access the shared printer on the network home?
  2. You receive an error message/code?
  3. Have you tried sharing the computer and using collective housing resources?

  As you mentioned, you can share printer for two other computer running on Windows 7, you can check the items below that will provide you with information on how to work with the host group, and also another article that will you provide steps on how to share a printer on the network.

  Homegroup from start to finish

  Share a printer

  Hope that the information provided is useful. Let us know in case you need additional assistance.

  Thank you.

• How can I share network between the computer laptop windows 7 into a window of 8 tab?

  How can I share network between the computer laptop windows 7 into a window of 8 tab?

  Hi HollyMcColl,

  Thanks for posting your query in the Microsoft Community Forums.

  I understand from the description of the issue you are trying to share the computer network between Windows 7 and Windows 8. I will certainly help you in this regard.

  I appreciate if you could help me with more information.

  -Using Windows 8 Surface RT?

  Note: You can create a Windows RT PC home group, but you can join one.

  I suggest you to consult the help articles and check if it helps.

  A Wi - Fi & networking

  http://Windows.Microsoft.com/en-in/Windows-8/HomeGroup#1TC=T1

  Share files on a home network or your Surface

  http://www.Microsoft.com/surface/en-us/support/storage-files-and-folders/share-files-on-a-home-network?LC=1033

  Share files and folders on a network or shared PC

  http://Windows.Microsoft.com/en-us/Windows-8/share-files-folders

  Get back to us if you need further assistance on Windows 8. We will be happy to help you.

• javax.xml.stream.XMLStreamException: unexpected end of Document

  from one moment to the other occurred to me this error. I did not something new. can someone help me?

  < 19 August 2015 11:33:54 CEST > < critical > < WebLogicServer > < BEA-000386 > < server subsystem failed. Reason: weblogic.security.SecurityInitializationException: loading of the OPSS java security policy provider failed because of the exception, see exception stack trace or the root server log file. If still don't see no obvious cause, turn on debugging of the flag - Djava.security.debug = jpspolicy for more information. Error message: cannot read the policy store. Reason is the error PolicyStore javax.xml.stream.XMLStreamException: unexpected end of Document

  weblogic.security.SecurityInitializationException: loading of the OPSS java security policy provider failed because of the exception, see exception stack trace or the root server log file. If still don't see no obvious cause, turn on debugging of the flag - Djava.security.debug = jpspolicy for more information. Error message: cannot read the policy store. Reason is the error PolicyStore javax.xml.stream.XMLStreamException: unexpected end of Document

  at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.loadOPSSPolicy(CommonSecurityServiceManagerDelegateImpl.java:1398)

  at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initialize(CommonSecurityServiceManagerDelegateImpl.java:1018)

  at weblogic.security.service.SecurityServiceManager.initialize(SecurityServiceManager.java:873)

  at weblogic.security.SecurityService.start(SecurityService.java:141)

  at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64)

  Truncated. check the log file full stacktrace

  Caused by: oracle.security.jps.JpsRuntimeException: cannot read the policy store. Reason is the error PolicyStore javax.xml.stream.XMLStreamException: unexpected end of Document

  at oracle.security.jps.internal.policystore.xml.XmlPolicyStore.buildFromFile(XmlPolicyStore.java:496)

  to oracle.security.jps.internal.policystore.xml.XmlPolicyStore. < init > (XmlPolicyStore.java:276)

  at oracle.security.jps.internal.policystore.xml.XmlPolicyStoreProvider.getInstance(XmlPolicyStoreProvider.java:100)

  at oracle.security.jps.internal.policystore.xml.XmlPolicyStoreProvider.getInstance(XmlPolicyStoreProvider.java:74)

  at oracle.security.jps.internal.core.runtime.ContextFactoryImpl.findServiceInstance(ContextFactoryImpl.java:139)

  Truncated. check the log file full stacktrace

  Caused by: oracle.security.jps.JpsRuntimeException: javax.xml.stream.XMLStreamException: unexpected end of Document

  at oracle.security.jps.internal.core.datastore.xml.XmlDataStoreParser.getDataStoreEntryStax(XmlDataStoreParser.java:166)

  at oracle.security.jps.internal.core.datastore.xml.XmlDataStoreParser.getDataStoreEntry(XmlDataStoreParser.java:180)

  at oracle.security.jps.internal.core.datastore.xml.XmlDataStoreParser.getDataStoreEntry(XmlDataStoreParser.java:187)

  at oracle.security.jps.internal.core.datastore.xml.XmlDataStore.loadXmlDataStore(XmlDataStore.java:411)

  to oracle.security.jps.internal.core.datastore.xml.XmlDataStore. < init > (XmlDataStore.java:276)

  Truncated. check the log file full stacktrace

  Caused by: javax.xml.stream.XMLStreamException: unexpected end of Document

  at weblogic.xml.stax.XMLStreamReaderBase.getElementText(XMLStreamReaderBase.java:289)

  at oracle.security.jps.internal.policystore.xml.StaxPolicyStoreParser.getElementText(StaxPolicyStoreParser.java:4815)

  at oracle.security.jps.internal.policystore.xml.StaxPolicyStoreParser.processPermission(StaxPolicyStoreParser.java:4760)

  at oracle.security.jps.internal.policystore.xml.StaxPolicyStoreParser.processGrant(StaxPolicyStoreParser.java:4309)

  at oracle.security.jps.internal.policystore.xml.StaxPolicyStoreParser.processJaznPolicy(StaxPolicyStoreParser.java:4253)

  Truncated. check the log file full stacktrace

  >

  < 19 August 2015 11:33:54 CEST > < opinion > < WebLogicServer > < BEA-000365 > < changed failed State Server >

  < 19 August 2015 11:33:54 CEST > < error > < WebLogicServer > < BEA-000383 > < is not an essential service. The server will shut down >

  < 19 August 2015 11:33:54 CEST > < opinion > < WebLogicServer > < BEA-000365 > < server status changed to FORCE_SHUTTING_DOWN >

  Process is complete.

  I have change the file system-jazn-"Data.xml" and his works.

• How to configure the network between the host (Windows 8) and Guest (Linux)

  Hello

  I am trying to configure network between the host (Windows 8) and Guest (Linux). Guest on VMware Workstation 8.

  Using this network, I want to configure putty so that I can access comments linux to a PuTTY that is installed on the host (Windows 8).

  Thank you.

  Abdul

  To obtain external access to comments (access the guest from the host), you must configure the IP static within the guest (Linux) as below and restart the network (service network restart)

  eth0 is a dynamic IP (DHCP) to get wireless internet access

  eth1 is a static IP address

  

  

• Networking between virtual machines on different hosts

  Hello

  I need some advice on the basic approach to networking between virtual machines, each running on a different host machine.

  Consider the following configuration:

  I have a few processes that are running in a Machine virtual Ubuntu. Call this guest1.  I guest1 race inside a real computer running Windows XP SP3 and VMware Workstation 7.x; Call this host 1.

  I have a copy of this virtual machine that I put on another machine.  Call this Guest2.  I have Guest2 running on a separate physical computer, also runs Windows XP SP3 and VMware Workstation 7.x; Call this host 2.

  Now, I would like to guest1 and 2 comments to make networking with eachother.  I wish they were able to ping, SSH, etc., among others.

  This is where I am stuck. I tried setting the virtual machines to use the bridged network mode.  I tried to connect my router on each computer and manually assigning IP addresses to each host and each virtual computer.  When I do this, guest1 can Host1 and Host2 ping, but cannot ping Guest2 and vice versa.

  What is the right way to do this kind of network?  This seems like an obvious application, if you want to perform simulations on multiple virtual machines residing on different computers on the network.

  I apologize if this is the answer elsewhere, I had to dig and was not able to find the solution.

  Thanks in advance!

  Charles

  Guests must be on the same subnet, like 'real' hardware machines.

  1 when you copied the VM and then started, what did answer you the question of copy/move? (this determines if a new MAC address is applied)

  2 view each guest and ' ipconfig/all' results 'ifconfig - a' by the hosts.

  Lou

• Build a private network between two physical hosts in ESXi 4.0 for VM guests

  Hi all

  I am a newbie in the use of VMWare ESXi for my company testings and I have a question on networks

  in ESXi. In fact, I always do my tests in my VMware Workstation, and it's pretty easy to build a virtual

  private network between two guests of computer virtual and it needed to do more real testings on ESXi environment.

  But now I have two Dell servers mounted and with two ESXi 4.1 installed on these servers.

  Each server has two network cards connected to the same network switch.

  In this essay, I have to install a RAC Oracle 11 g as guests of virtual computer on two separate server Dell for

  two RAC nodes.

  The installation Guide for the PAP, I need to build a network between two nodes.

  My superficial knowledge network, the private network address is not the same as

  the public network address, in this case, the IP address provided by the network switch is

  10.1.10.X and it should be public network address.

  In this case, how can I do the private network of ESXi settings?

  I do the settings of the network switch? I'm not the guy of networking and really

  want your expertise in this area.

  If you have an idea or experience to share, please kindly help.

  Thank you very much

  Ray

  SonyRaymond wrote:

  Then private network can be established between NIC (N1) and NIC (N2) with address 192.168.1.X

  range?

  Yes, that's correct. It would have made you have a private network layer 3 between the two guests in the 192.168.1.x address range.

  In general, you also want to isolate a layer 2 (ethernet) with the VLANS on the physical switch, but if this is not possible at this time then it could be implemented now and you could later add VLAN in the switch.

  It is also the reason why I think you should create a new portgroup on the same vSwitch as other existing exchanges. If you later configure VLAN to the physical switch, it will be very easy to activate this on the "private" portgroup

• will be failover testing with success when the network between the site of protect and recover is broken

  Hi friends,

  When the network between the site of protect and recover is broken, will be the successful test SRM failover?

  Thank you.

  Hello

  There was a theme with exactly the same question, but I'm not.

  IIRC, the answer was: it depends on storage / Some SRA. of them need connectivity.

  Michael.

• Create a simple internal network between two or more virtual machines

  Hello guys,.
  I just wanted to ask how to create an internal network between several virtual machines without the host must be a part of.

  I don't want that your network has a NAT, but I want to HOST a part of another network.

  
  I tried the changes on network cards, but does not work...
  Obviously with VMware Workstation 8

  Yes, your "Virtual Machine settings" - screenshot #1 - Select VMnet2 (for example).  Do this for each customer that you want on this private network, "Guest-only.  Note that you need to configure the network settings on each client within each guest OS; or have a guest to be a server with a dhcp server running that other clients can obtain an IP address configuration of.

• Networking between the virtual machine with the operating system Linux in VMWorkstation

  I'm new to Vmware Workstation 7

  I had installed vmware workstation on XP. I created two virtual machines with RHEL 4. I am unable to network between two virtual machines.

  I can't make a ping a machine to other Linux, which is the operating system on both the machine. However, cannot connect ftp or can't see computer networked in computer > network under linux...

  I had used the guest network only on both the machine with the same adapter vmnet8 (considering as switch) and have assigned static IP address at a time

  ORDI1 - 192.168.42.21

  COMP2 - 192.168.42.10

  and also have installed vmware tools on both the machine...

  can someone help me on this...

  muzaffar700 wrote:

  I can't make a ping a machine to other Linux, which is the operating system on both the machine. However, unable to

  ftp connection or may not see computer networked in the computer > network under linux...

  Disable all firewalls in your linux guests.

  I had used the guest network only on both the machine with the same adapter vmnet8 (considering as switch) and have assigned static IP address at a time

  ORDI1 - 192.168.42.21

  COMP2 - 192.168.42.10

  and also have installed vmware tools on both the machine...

  can someone help me on this...

  Host-Only is VMnet1, you used only NAT. static use of intellectual property and switch to DHCP for now. Make sure that the VMWare DHCP Server service is running. Put network cards in comments to "host-only '.

  Post your host ' ipconfig/all'.

  AWo

  VCP 3 & 4

  Author @ vmwire.net

  \[:o]===\[o:]

  = You want to have this ad as a ringtone on your mobile phone? =

  = Send 'Assignment' to 911 for only $999999,99! =

• Catalyst 3560 liaison network between two servers ubuntu 12.04

  Hello world

  I'm trying to transfer data with more than 1 Gbit/s between two servers, but I just get a card (approximately 1 Gbps) NETWORK performance. Here is my configuration:

  srvnettest1 and srvnettest2 are two 12.04 servers ubuntu with three network cards in each. management eth0, eth1 and eth2 are network cards that should work as a team. ;-) Here are the relevant parts of fit it:

  [email protected]/* */:~# less /etc/network/interfaces
  ...
  auto bond0
  iface bond0 inet static
  address 172.16.200.100
  netmask 255.255.255.0
  bond-mode 4
  bond-miimon 100
  bond-slaves none
  bond-lacp-rate 1
  bond-primary eth1 eth2
  auto eth1
  allow-bond0 eth1
  iface eth1 inet manual
  bond-master bond0
  auto eth2
  allow-bond0 eth2
  iface eth2 inet manual
  bond-master bond0
  ...
  
  

  
  [email protected]/* */:~# less /etc/network/interfaces
  ...
  auto bond0
  iface bond0 inet static
  address 172.16.200.200
  netmask 255.255.255.0
  bond-mode 4
  bond-miimon 100
  bond-slaves none
  bond-lacp-rate 1
  bond-primary eth1 eth2
  auto eth1
  allow-bond0 eth1
  iface eth1 inet manual
  bond-master bond0
  auto eth2
  allow-bond0 eth2
  iface eth2 inet manual
  bond-master bond0
  ...
  
  

  It's the switch configuration (btw, this is a version of IOS in course WS-C3560G-48TS 12.2 (55) SE)

  Switch#show running-config
  ...
  interface Port-channel10
  switchport access vlan 200
  switchport mode access
  !
  interface Port-channel20
  switchport access vlan 200
  switchport mode access
  !
  interface GigabitEthernet0/1
  switchport access vlan 200
  switchport mode access
  channel-group 10 mode active
  !
  interface GigabitEthernet0/2
  switchport access vlan 200
  switchport mode access
  channel-group 10 mode active
  !
  interface GigabitEthernet0/3
  switchport access vlan 200
  switchport mode access
  channel-group 20 mode active
  !
  interface GigabitEthernet0/4
  switchport access vlan 200
  switchport mode access
  channel-group 20 mode active
  ...
  

  This is my summary etherchannel:

  Switch#show etherchannel summary
  Flags:  D - down        P - bundled in port-channel
  I - stand-alone s - suspended
  H - Hot-standby (LACP only)
  R - Layer3      S - Layer2
  U - in use      f - failed to allocate aggregator
  M - not in use, minimum links not met
  u - unsuitable for bundling
  w - waiting to be aggregated
  d - default port
  Number of channel-groups in use: 2
  Number of aggregators:           2
  Group  Port-channel  Protocol    Ports
  ------+-------------+-----------+-----------------------------------------------
  10     Po10(SU)        LACP      Gi0/1(P)    Gi0/2(P)
  20     Po20(SU)        LACP      Gi0/3(P)    Gi0/4(P)
  

  My test tools are nuttcp (by transfer) and bmon (to watch what is happening during the transfer). Unfortunately, I am not able to transfer more than 1 Gbps:

  [email protected]/* */:~# nuttcp -i1 172.16.200.100
  97.1875 MB /   1.00 sec =  815.2409 Mbps     0 retrans
  98.0625 MB /   1.00 sec =  822.4763 Mbps     0 retrans
  98.0625 MB /   1.00 sec =  822.7321 Mbps     0 retrans
  98.1250 MB /   1.00 sec =  823.1001 Mbps     0 retrans
  98.0625 MB /   1.00 sec =  822.5306 Mbps     0 retrans
  98.0625 MB /   1.00 sec =  822.7560 Mbps     0 retrans
  98.1250 MB /   1.00 sec =  822.9890 Mbps     0 retrans
  98.0625 MB /   1.00 sec =  822.6753 Mbps     0 retrans
  98.0625 MB /   1.00 sec =  822.5528 Mbps     0 retrans
  98.0625 MB /   1.00 sec =  822.7058 Mbps     0 retrans
  982.5000 MB /  10.03 sec =  821.9606 Mbps 21 %TX 37 %RX 0 retrans 0.32 msRTT
  

  In bmon, I see that a NIC (eth1) of bond0 the uplink and the other a (eth2) made the downlink:

  #   Interface                RX Rate         RX #     TX Rate         TX #
  qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq
  srvnettest2 (source: local)
  0   lo                         0.00B            0       0.00B            0
  1   eth2                     269.26KiB       4175       0.00B            0
  2   eth1                     123.00B            0     102.56MiB      71030
  3   eth0                     179.00B            2     491.00B            1
  4   bond0                    269.38KiB       4176     102.56MiB      71030
  

  I tried a lot of things, but now I have no idea what to do or what to try next. It is true that I have no deep understanding of Cisco etherchannels yet, so I guess that my mistake is somewhere in the IOS configuration.

  Thanks a lot for your support and welcome to Germany

  Stephan

  Hello Stephan,

  With EtherChannels, a single flow (the flow of images/packages with the same source and destination) is always carried by a single link only. Implementation of Cisco implements not balancing on connections in an EtherChannel load by package, and it avoids a reason: executives could get reorganized, something this plain Ethernet never should do. This means that you will not see an improvement in bandwidth on the speed of a single link to your EtherChannel for a single stream. It is only the overall bandwidth for several stream which increases. The advantage of EtherChannel becomes therefore obvious that if your server starts many conversations and several stream handling.

  Best regards

  Peter