stream of while loop

Similar Questions

• What is READ the array returned by the DAQmx meter? How can I know the two functions DAQmx READ data stream in the same WHILE loop?

  I have a question about the order of execution.  In the WHILE loop, I have two things to measure, period and tension using the DAQmx READ functions for voltage and the meter.  In the end, I want to collect these data as points almost simultaneously as possible, as a pair and then send them together to another piece of code (not shown here) which them will result in some sort of command for an engine.  It would be run, and then I want to perceive the tension and the period at a time later and do the same thing.

  (1.) I'm a little confused on what the meter of the READ function is back because it's a table.  What is a picture of?  I thought that it was up to the value of the individual periods between rising edges.  The output of the counter 1 DBL d's a table. How many elements in this table, and what determines the size of this table?  Are the elements of the array the individual delays between the edges?  How many values are stored in the array by executing?   We take the AVERAGE of the last 15 items, but do not know if we are throwing some of the data or what.  How to understand the composition of this painting?  How can I change the composition of this painting?  Is it possible to measure only one period at a time, for example the time between TWO edges?

  2.) Will this WHILE loop execute as it gathers tension and a "period table ' (remains to be understood by me) by TIME running in a loop?  In particular, we want that the value of the tension associated with the value of the AVERAGE of the period "array", so we can use two data items to create orders of next control every time that the two values are reported.  The structure for the delivery of vi will be attached data in pairs like this?  I understand that one of the READING functions run not before the other function of READING in the WHILE loop.  I want that the period "means" and "strain (Volt) collected at the same pace. This vi will he?

  Thank you

  Dave

  Hi David,

  I suggest including the DAQmx Start Task function. If it does not start before the loop, it starts the loop and work very well, but it is not as fast and efficient. In the model of task status, task wiill go to run the checked each iteration of the loop and then back the time checked running when it restarts.

  The status of the task model: http://zone.ni.com/reference/en-XX/help/370466V-01/mxcncpts/taskstatemodel/

  Kind regards

  Jason D

  Technical sales engineer

  National Instruments

• HAVE multiple AO-synchronization-2 multiple while loops

  Hi all

  I want to characterize my RF circuit by using an additional narcotics control and map PXI-6229. I wrote a simple VI in Labview, which is almost similar to the example, multiple-HAVE-AO-synchronization, seen in LABVIEW. According to my VI, 4 analog outputs with different offsets dc, amplitudes and phase values must be generated to my RF circuit and 2 analog inputs must be acquired by this circuit simultaneously and continuously. But the problem with my VI is that I try to observe two diagrams at the same time to see the changes in signals generated and acquired. However, I don't see the two signals simultaneously. The second while loop, which belongs to the acquisition of analog signals, does not start while the first loop generates analog signals continuously. How can I synchronize these two while loops in order to observe the two parties in the diagrams?

  I have attached my VI.

  Thanks in advance.

  T. Eray

  Hi Eray,

  I will be brief and I'll keep it simple. If I understand correctly, you have trouble with the data stream in LabVIEW. When you work in LabVIEW, you must understand the order in which the blocks (functions/nodes/structers) are run in LabVIEW - stream. Each block can be executed just at the moment where there values on each entry. This means that if the 2 blocks are connected with a wire, the 2nd block waits until the first ends its execution.

  In your case, that means, this 2nd loop does not execute before the first loop (with the DAQ Assistant) ends its execution, because the son comes from the inside of the first loop, then they go to some DAQmx features and then DAQmx features they go to the 2nd loop.

  In principle, what you could do is to put the content of the first loop, where you prepare the signal generated in the 2nd loop. Good course without the DAQ Assistant. Instead, you can use DAQmx writing in the 2nd loop.

  Kind regards

  Martin

• Writing file case structure while loop?

  I would like to have a button on the front panel which indicates to start streaming data recording or not.  If the user does not press a button, no data is saved, and the façade works only as a display of data.

  I have now does not correctly.  The button is a while loop that is attached to a matter outside the loop structure.  I would like to a false statement to not save data to any file, but I needed to wire my knots of structure dealing with something, so the T and F are currently the same action (sort of).  How do I wire this configuration correctly please?

  Thank you!

  
  

• How to add the unique element (inside the while loop) to itself

  I have only digital output element that is in the while loop. Its value changes in each time the loop iteration. If lets say I want to adds the values of the ten first in iterations of the loop of this variable.  How can I do that.

  See attach image for more precision.

  Thank you

  JK

  

  Hi Joseph,.

  THINK THE STREAM!

  As the values are stored in the son and the shift registers (and NOT in any kind of variables), you must use these fundamentals of LabVIEW:

  

• While loop with reading of text file - calendar of events in a given period

  Hello world.

  I created a program that if serial interface via a port to a syringe push in my lab. Currently, the program reads in a text file-flow rate values and sends them to the pump, one by one, through various commands. I need to ensure that whenever a new flow rate value is sent to the pump, it does in a specific/hard time for a while. I.e. every 0.1 seconds, changes in flow rate and must are active until the next period. I tried to use a timed loop and I think I've succeeded, but it hogs system resources, so I was wondering if there was a way to do it using the number of cycles or something of this nature. I just started using LabView, so I'm slowly getting the hang of it (easy when you watch my VI!)

  See attached VI. I took orders from serial port and have instead orders display in an indicator. The nested and densely populated while loop contains the commands that need to be completed/last during the period (like 0.1 second).

  Thank you for your time and help!

  -Phebotalus

  Hi, you should read some introductory material on LabVIEW to down the idea of the stream.

  Basically, the data flow in the wires from left to right, and any node will not work until it has reached all of his contributions.

  The thread of the error is the best way to run data streams.

  ***

  In your VI I use data wires, their execution through structures, and forcing the structures to run in the sequence.  Using a structure of sequence you mentioned in your next post will force the two scripts to execute in the order of (the only one we discussed to be in race condition.)

  Similarly, for brevity, I would wrap the EMO and she is business structure in a single sequence and force it to run last using stream.  In this way the user has the most possible time to decide to hit the EMO before she is called by the application.  As it is now, it most likely is interviewed at the beginning of the loop, so if it's the exchange value you won't see results until the next loop.

  When running in execution of highlight you see the order of data flow, but that is not guaranteed to be the same for a normal performance, where the use of the data stream.

  ***

  The counter tick account ms up to a very large number and then "says" reset and start counting again.  I know you want to START the loop as close to every 10 ms.  Yes, using data flow, take the number of cycles first, perform actions, then return the number of cycles.   The second time of the tick read that you are in a nested loop that does not stop until you get 10 or more difference on the number of cycles.

  And, on the off chance that you must achieve "return" on the tick counter comes stops the nested loop then move.  (if the second measurement is less than the first, then the tick counter handed.  If you miss this situation while you'd have to wait a long time for the condition of the difference > 10 in the reunion, basically locked in the loop.

  ***

  You could put the EMO sequence, we have seen, in line with data streams.  Before or after the second control of ticks will not make much difference in terms of 10ms.  I would put it after checking the tick, again give the user more time to hit the EMO if necessary.

  ***

  I put in a queue for the stream error and removed the other stuff.

  LV2010

  Check out some of the LabVIEW intro docs, they are online, they discuss these issues and much more.

• stop a while loop in slot - VI

  Hello

  I have a Subvi, which has a while loop and it is in my main vi in a sequence structure, I want to stop the loop inside the Subvi using a Boolean value in primary vi.

  I tried global variable, but it has not worked since the stop in my main vi botton is not updated when the program is running...

  could you please help me?

  I appreciate any ideas

  Thank you

  Darya

  As a general rule, avoid using Structures of the sequence.  The reason being that they are violating data streams.  If you can control the flow of data with threads, it is the most effective way to make your program work.  The idea to get rid of your sequence structures is therefore to make an another Subvi to your expectation that also has an error and output error.  Then, you can use the cluster of error to force execution.

  And while loops inside the subVIs is a common beginner problem.  If you do not order when the loop ends based on a front panel of the mainVI control, then the loop must be in the main VI.

  I hope it's a good summary of what was said.

• Is it possible to execute a loop For independently within a while loop in LabVIEW 2013?

  In my program, I want to run a loop For inside a while loop and run independently, at their own rate of execution.  A test, I wrote a simple VI with a while loop with 1 second calendar and in this I inserted a loop For with 3 of a second.  I created indicators for the two terminals of the iteration.  When executing the VI, I found the while loop waiting for loop For run N times before the while loop is executed again.  I also found that sometimes the first iteration of the loop For ends at 1 second instead of 3 seconds and the STOP button to complete execution of the While loop does not always work.

  This is the expected behavior. LabVIEW is the language of s DATA stream. If you want the curls to be independent, it can be data forcing addictive so use separate loops.

• How to increase code efficiency in a while loop (using PXI5105 for sampling outside signal digitalizer)

  Theoretically, we want the PXI-5105 (digitizer) have 302 record with each record has a 1260 sample (the save operation is inside a while loop) in approximately 30ms, however we have found that for each period (30ms), the PXI5105 only perform about 10 records. It is so wired. I wonder if the operations inside the while loop consume more time (for example 3MS), so that he cannot have 302 records even the PXI-5105 have 60 M/s speed of sampling. Is it true, you can find my labview code and if possible can you give me some suggestion in the most short time of operation of the loop.

  

  Please find attached labview code.

  Hi g_l_g_s,

  The digitizer PXI-5105 acquires data at the speed that you specify and stores the data in its memory embedded (up to 512 MB). The data is then sent to your computer when the Multi Fetch Cluster.vi is called. In VI that you posted, you are only fetch record during each while the loop iteration. If you want to retrieve 302 records you will need to specify 302 files in the horizontal Timing.vi to configure. For more information about scanners, you might find the DevZone, hereuseful.

  To determine the amount of time it takes for each while the loop iteration, you can consider using the structure of code in the example comparison community calendar, which is located here.

• structure of the event + while loop

  Hello, I am trying to understand how to unite two while loops in attached VI for half a day

  The first loop creates a state machine solid which reacts on each key and runs one of the structure cases. (that part works very well)

  The second loop, always generates the random number, but it stops the generation during the time where one of the structure cases events are executed. (this is the part ticky)

  Any suggestions?

  If you want your random number to stop so that the user triggered events are running, you should be able to simplify your design a lot.

  It can be done with a loop using the case of timeout.

• Retaining the last value without a while loop

  Hello

  I'm using LabVIEW 2013. My VI is attached. I'll send in a 'Curr. Random random numbers TestPlan Row"time. I'm eager to keep his last number, whenever this VI is not called and then reset the value to its new value whenever the VI is called again and a new number has been sent. Also attached is a screenshot at the VI.

  Please note that I can't use a WHILE loop, so it must keep its value in a different way...

  Thanks in advance for any help!

  SM

  Maybe a feedback node?

• convert loop timed to normal while loop

  How convert a while loop time normal while loop with exact same properties and performance?

  I have donot need to worry about the exact date. But it takes the timed loop time will be run similar to loop.

  And also, is there any issue encountered when we use Timed loop? problems such as that crashing exe?

  Hello

  1 kHz is the used base clock. Then, you decide to use 10 as period (dt) which is 10 ms.

  The clock is selectable in real-time systems, you can use the 1 MHz clock, giving resolution µs

  But for your needs, using 1 kHz clock with dt = 10 and using a ms of waiting with 10 connected to it is exactly the same.

• Functions don't run when a loop running in a while loop

  Hi all

  I have a loop within a while loop. All main functions are running in this while loop. However, once the for loop executes other functions in the while loop don't work anymore until the loop for stop execution. Could someone help me with this problem? Thank you.

  Kind regards

  Nicky

  Hi Nicky,

  Ah, well I don't have much suggestions but maybe you can try with a conditional for the loop. I've attached an example. You can go through it. I don't know if it's a good idea to use this way, but again, if this can help, so I'm glad that.

  To create a condtional for loop, place a normal for loop on the block diagram, right-click and select terminal condtional.

  Kind regards

  Amine31

  (Give congratulations to good answers and Mark as a Solution If your problem is resolved)

• CPU utilization while loop

  Manual LabVIEW declare a while loop must always contain a "wait for ms" vi to unlock the task for this period.

  However, I thought that it the same fate if I use the same timeout ms for the timeout of a structure event inside the while loop

  and omit the "wait for ms" vi.

  Unfortunately the time-out of the structure of the event does not seem to unlock the task so that the façade reacts very inert in this case, even if it reacts
  prompt in either case.

  Does anyone have an explanation more in depth of this behavior?

  
  

• While loop, wait for the function and the stop button!

  Hello

  I have a while loop and a stop button. Inside my While loop - I have a 'Wait (x ms)' function. If I press the stop button, it does not block the program immediately, he expects ms x then stops the program. How can I get rid of this?

  Thanks in advance for the help!