Studies of physics, usable software?

Similar Questions

• A10: You are looking for a physical formatting software

  Hello
  I am looking for software to do a physical format for my HARD drive. I have a Satellite A10.
  I want to erase all sector and create a new one because I have a serieus probem.
  If anyone knows where I can find it please help!

  Thank you

  Hello

  Please visit this link.
  http://www.dposoft.NET/

  I think that this s.

  Good bye

• Flow Control on iSCSI physical NIC software

  Hello

  I want to activate flowcontrol throughout the network iSCSI - how to activate it on the network adapters that are related to the initiator of the software?

  This is a deployment ESX 4.0 U1.

  Concerning

  I'm reasonably sure that the flow control is enabled by default on GB ethernet

  You can use ethtool to view / change settings of network adapters.

  ~ # ethtool vmnic0
  Settings for vmnic0:
          Supported ports: [ TP ]
          Supported link modes:   10baseT/Half 10baseT/Full
                                  100baseT/Half 100baseT/Full
                                  1000baseT/Half 1000baseT/Full
          Supports auto-negotiation: Yes
          Advertised link modes:  10baseT/Half 10baseT/Full
                                  100baseT/Half 100baseT/Full
                                  1000baseT/Half 1000baseT/Full
          Advertised auto-negotiation: Yes
          Speed: 1000Mb/s
          Duplex: Full
          Port: Twisted Pair
          PHYAD: 1
          Transceiver: internal
          Auto-negotiation: on
          Supports Wake-on: g
          Wake-on: g
          Current message level: 0x000000ff (255)
          Link detected: yes
  

  Use

  ethtool -A vmnic0 rx on tx on
  

  to enable flow control for transmit and receive.

• Camileo H20 - a few questions and the new firmware?

  OK, many users know that it is one of the worst cameras, you can buy.

  Firmware is really sick, then, how to use it?

  To start, I'll repeat known bugs:
  -very slow development, so its impossible to zoom in/out
  -camera is not connector to plug in an external microphone
  -internal MIC is the gift of a hell, he died later, big bang.
  -Its hard to listen to the people, because internal microphone is sensitive as one of the worst last factory of China
  -light balance is crazy, the processor is switching mode light for fun in automatic mode
  -record is worse than much cheaper cameras and more, is probably preferable to buy an old camera from Sony again Toshiba

  I don't like Toshoba, because its my third bad product Toshiba.
  After good notebook Toshiba, I bought new a lot less good and the other and the camera. I think that production will only worse in 2005.

  Camileo H10 was also sick, but for this unit was out of usable software.

  Last year, I bought used Camileo H20 with part number PX1478E-1CAM on eBay and use it from time to time. I use it mostly to the outside because if there is no light in the room I m not so satisfied with the quality of the photo.
  Sound is not the best but not so bad, and in General, for this price the cam is OK.

  When I read the list of known bugs, the first thing I have to say is: you bought the bad cam.
  What you need is the cam of high quality and the price for this cam is around 700 Euros. I wish I had this cam too but I'll wait for prices to fall a little.

  Please note: Camileo H20 costs 140 Euros only. For that money, the cam is really OK.

  With laptops is the same: it depends on phone model. The quality for the Satellite C model is certainly not the same as that of the P of Satellite series. Best evidence is the price.

  In my country, we have a saying that applies: that cannot pick up the right product, must buy expensive. It is difficult to translate, but I think you know what I'm talking about m. ;)

• HP Pavilion a6000n desktop: adding false graphic RAM and freezes start.

  Well, I'm back with the same machine as the previous assignments.  I ordered the recovery of Surgeons of the computer disks and that they were unnecessary because the computer does not see any cd/dvd I have to install.  Finally gave up and ordered a Windows Vista recovery usb flash drive and installed the operating system.  I used it very well with the RAM minimum (1 GB).  I decided to upgrade the memory to use all 4 GB.  All four are recognized in the BIOS/Setup with the full 4 GB dispalyed.  The new brand of memory is Samsung.  Everything seems to be as it should.

  Here's the problem: the Windows splash screen appears with the scan progress bar and when it gets to the sixth pass it freezes as black and alternating vertical lines distorted graph color vertical lines appear.  It will remain so until I have shut down, because he has not answered all the keyboard commands.

  I removed two 1 GB modules and restarted without problem.  I've tried three, and he did nothing.  Swapped the output for the two 1gbs modules, I removed and they worked perfectly.  With four on board is the problem presented and only when windows is loading.

  I also tried safe mode.  All four ram modules work with the VGA drivers in safe mode without graphical distortions or freezes.

  I tried to restore the computer to an earlier time with the console of Windows Vista repair because he found from the problems and suggested this course of action.  When I did, he removed my Firefox browser.

  Has anyone seen this problem before or a solution?  Thank you for help.

  What follows is my computer information system:

  Name of the Microsoft® Windows Vista™ Home Premium operating system
  Version 6.0.6002 Service Pack 2 Build 6002
  Another Description of the OS is not available
  Manufacturer of operating system Microsoft Corporation
  Name of the system
  System manufacturer HP-Pavilion
  System model RX885AA-ABA a6000n
  System Type X 86-based PC
  Processor AMD Athlon (TM) 64 X 2 Dual Core Processor 4200 + 2200 Mhz, 2 Lossnay, 2 logical processors
  Version/Date Phoenix Technologies, LTD 5.13, 29/10/2007 BIOS
  SMBIOS Version 2.4
  Windows directory C:\Windows
  System directory C:\Windows\system32
  Boot Device \Device\HarddiskVolume1
  The local United States
  Hardware Abstraction Layer Version = "6.0.6002.18005".
  Username
  Daylight saving time from the centre of zone
  Physical memory (RAM) installed 2.00 GB
  1.87 GB total physical memory
  Available physical memory 775 MB
  Total virtual memory 3.99 GB
  2.49 GB available virtual memory
  Page file space 2.17 GB
  Paging file C:\pagefile.sys

  HP Pavilion a6000n specifications

  Before that I inform you of why 4 GB will not work, I will inform you of the steps, I took in coming to my conclusion.

  First of all, I found an old PCI VGA card and installed.  Then I started the installer and changed to display pci dashboard.  F10 save and exit.  I left Vista find the new hardware and drivers.  Power off and swapped the cable from the monitor with pci card.  Restarted.  Last good known Configuration.  Made to the desktop with large icons, display etc.  Power off.  Installed all four modules of memory of 1 GB.  The installer confirms the mms of 1 GB in all four banks.  Save and exit.  A frozen fourth passage on the starting Windows progress bar screen.  Display is now less than a hundred multicolored pixels (it looks like stars in the night sky) scattered across the screen with barely perceptible ms inside progress bar.  Killed power as no response to input devices.  Modules removed from DIMM0 DIMM2 (banks 1 and 3) and installed two 512 MB mms instead.  Power, entered installation.  Confirmed 1 GB, 512MB, 1 GB, 512MB in DIMM0-4 (banks 1-4).  Save and exit.

  Eureka!  Starts directly on the desktop with no complications.  Vista even automatically the Resolution 1600 x 900 display value.

  Power off.  Remove the PCI card.  Has changed from the monitor to the integrated connector cable.  Powered on the Setup where I changed the display on board.  Saved and get out.  Straight to the desktop.  All right.  Vista indicates on the installed 3,072 GB 3.0 GB.

  I had read a useless article on the HP Forum that said that HP had made disappear the memory alternative banks.  Thank you for that.  Thanks kaoutar to straighten me out on this.

  After studying the limits of memory on Windows os systems, I made a discovery.  Due to the limitations of physical or software address, Vista cannot use 4 GB RAM in the 32-bit operating system.  You must install os 64 bit where it can use 8 GB to 16 GB.

  Here are a few discussions of support, I found to cooberate my conclusion that 4 GB will not work on this computer, as this is with Vista 32 bit installed.

  Thanks for the reply and assistance Erico.  Installation of Bank alternation of RAM modules corresponding coupled to the reduction of two of these 512 MB back is the solution.  It was an error of installation of equipment so many restrictions imposed by hardware and software manufacturers.  If I or anyone else, wants more RAM under Vista or 7, will need the 64-bit versions.

• Have an old drive anytime upgrade from Vista, it'll work now on a Vista, Microsoft discontinued anytime Vista?

  Buy a Vista anytime upgrade with a key, if I had a key usable software?

  A Windows Anytime Upgrade Vista disc can be used if you have an existing running Windows Vista installed and running.  It can be activated if you have a Windows Anytime Upgrade Vista genuine product key.

• How to get around Windows 7 SP1 requirement?

  I have a laptop DELL D630 old provided with Windows XP.

  I did the basic modernization of a few years ago (more large, RAM disk), and it is now running Windows 7 x 64.

  Everything on the laptop is very good for my development needs. It is fast enough, never has a problem and is connected to my docking station works well on my two monitors.

  I tried to install the Service Pack of Windows 7 a few times; However, installation fails because it cannot find compatible display and audio drivers. I already have the latest for both my old Intel onboard graphics and my audio is not DirectX 9 compatible.

  I need my screen and my audio, so I have not installed Service Pack 1.

  Now, I find that a lot of software out there will not install on my PC just because I'm still Win7 instead of Win7.1 (Paint.Net, Visual Studio 2013).

  So, what exactly is Windows 7 with Service Pack 1?

  Microsoft Web site:

  Windows 7 Service Pack 1 (SP1) is an important update that includes updates for security, performance, and unprecedented stability for Windows 7. SP1 includes new improvements to features and services in Windows 7, as an improved reliability when connecting to audio devices HDMI, printing using the XPS Viewer and restore previous folders in Windows Explorer after reboot.

  Ok. I do not allow any Windows updates on my PC and my laptop doesn't have HDMI. Therefore, these features do not seem an advantage to break on my PC.

  Essentially, it seems that there is nothing in Windows 7 preventing another installation physically new software that there are some entries in my Windows operating system that signals that is not quite new.

  Is there a way to change PC settings so that the installation of the software think that my PC has this service pack?

  So I ended doing some research on the Dell Web site.

  There, I had the model and version of the Intel integrated audio/video, then found an upgrade than on the Intel Web site, which was released this past August (was unavailable the first time I tried to upgrade to Windows 7 SP1).

  Then I upgraded the Dell BIOS to a version that was released in 2013. Before, I was recommended only to upgrade the BIOS in the reinstallation of the operating system, so I have not elected to do this. This time, it worked or I would like to reinstall Windows.

  After the reboot, I used Windows Update to select SP1 installed and rebooted.

  I came again with other than SP1.

  I used Windows Update again, even once selected and installed the Win 7 SP1. Yet once restarted.

  Second time's a charm. The second installation worked.

• network Windows 7 problem

  The problem is with a computer windows 7, which worked fine until the last update (windows Defender definition) February 3, 2014.  looks of stack network OK open cmd and ipconfig and ping the router correctly. Be able to see the configuration page of the router in IE11 and Firefox, however not able to see Web pages. Verified the remote desktop and can display the server's desktop. Outlook cannot see the mail server. Turn Windows defender, windows firewall and the antivirus firewall. have manual reset for ip and DNS tcpip however no change have used netsh reset in a cmd window tried to do a system restore but it fails. the problem must be with the software were used starting in minimal mode and safe mode with networking with the same result.
  Entered in the static ip address for a remote server and received a correct notification (you are not authorized to view this page) running options

  Hi Anil

  The computer of windows 7 is one of the 8 on a network with a windows 2008 Server. All computers bar you can see the internet.  The router status page indicates that it works correctly. I can RDP into the server from a remote location.  The tcpip and DNS for the computer with the problem have been working with the network card, no problem device is present in System Manager. I can't do a ping of the defective computer to all others on the network. In line at the seven layers of the OSI physical and software layers work properly, looks like it's fire to the walls of IE11 and Outlook.  Checking that all firewalls is turned off. System Restore starts and fails them.

  Have now resolved the issue. The last update to the computer was an update definitions for windows defender. I removed the update in safe mode with network and was able to do a system restore to the day before the problem. Windows defender is turned off and has been for many months, but this late update to the walls of the system software.
  Thank you

  concerning

• Win 7 freezes in HP p7 - 1137c

  Win 7, 6 GB ram, Hp p7 - 1137c

  Win 7 freezes several times a day, but not the cursor.  Also, I am able to "Ctrl-Alt-Del" via the keyboard to get in the Task Manager, but not immediately.  After 10-15 seconds, the Task Manager opens and Win 7 thaws. Help, please.

  Hello konadan

  Has anything changed since you first began to notice the problem (of the physical changes, software changes, etc.)? I suggest following the article below to solve your problem of freezing. You also use 32-bit or 64-bit Windows 7? Let me know what happens.
  Computer hangs or freezes (Windows 7)

• BlackBerry smartphones how cover the 8300 OS device?

  I have a Curve 8330 from Sprint, I wanted to use for my work eMail (BES).  Our IT guy apply all the tools the company official security and limits to allow me to be connected to the corporate mother ship.  I now left this employer and need to get my device back to the standard configuration (detail).

  If I download the new 4.5.0.295 device software package, will that physically restore software platform with version 3.4.0.55 and 4.5.0.175 Applications or is there something that needs to be done to clean the device first?

  Any help would be greatly appreciated.

  Thank you

  Ardyr

  Hi and welcome to the Forums!

  Not quite... Once you have a COMPUTER policy (which is what is applied with BES), you have to take much more radical measures to eliminate it. See the following article:

  • http://supportforums.BlackBerry.com/T5/BlackBerry-storm-BlackBerry-9500/remove-it-policy-from-person...

  Good luck and let us know!

• Applications available for blackBerry Smartphones

  Can I buy for my Curve 8520 newly gifted GSP? And what other useful applications should I look for? I'm 81, retired and nothing else to do but to be thrilled by the possibilities of this wonderful instrument.

  Hi and welcome to the Forums!

  Browndot513 wrote:

  Can I buy for my Curve 8520 newly gifted GSP?

  See this page of product specifications:

  • http://us.BlackBerry.com/smartphones/blackberrycurve8500/#! phone-specifications

  The 8520 has no internal GPS radio physics no software can overcome this physical limitation. You be relegated outside devices only, connected either via USB or BT, they are on the market, but I have no idea which are compatible with your specific model BB. You should look in GPS units that you like and then inquire of these manufacturers, if they are compatible with your BB.

  Browndot513 wrote:

  And what other useful applications should I look for?

  It is a difficult question... "useful" is a personal and subjective thing. I suggest you install AppWorld and browse here to see what would be useful to your different needs, desires and tastes.

  • http://us.BlackBerry.com/apps-software/appworld/

  I also suggest that spend you some time at this place:

  • http://us.BlackBerry.com/support/blackberry101/#tab_tab_style

  Good luck and welcome to the world of BB!

• Disable or password protect safemode

  I would like to password protect the safe mode.  Family members bypass the filters operating under safe mode.  How can I do this?

  I'm not aware of a built-in method to avoid a restart in Mode safe, but you can probably achieve your goal with a little effort, as follows:

  1. Create a Restore Point so that you can retrieve in case you get too locked.
  2. Burn a CD to repair unless you already have a.
  3. Identify a service which does not run in Mode without failure. I think that the Task Scheduler service is one of them.
  4. Place the below batch file in the following folder:
     C:\ProgramData\Microsoft\Windows\Start Menu\Programs\Startup
     Any name will do, for example, Startup.bat
     You need administrative privileges for this.
     The batch file stops the PC when opening of Safe Mode unless you log on under your own account.
  5. Log in Mode safe under one account other than your own to test the script.
  6. Make sure that none of your users have accounts with administrator privileges.
  7. Keep the passwords for all the secret of admin accounts.

  off @echo
  net start | Find /i "Task Scheduler" 1 > 2 draw > draw & goto: eof
  If/i "%nom user %" == "Administrator" goto: eof
  If/i "%nom user %" == "XXX" goto: eof
  stop/f/p

  Replace XXX with the name of your own account.

  Also note that you can start a trench warfare. Whatever you do for Windows, you can't prevent a person with the skills appropriate to cancel it if he or she has physical access to your machine. Instead of developing physical or software barriers, you can discuss with your family on a personal level. Play games of cat and mouse will not help everyone.

  Post again if you need more detailed instructions.

• Where to find the UI scale in Photoshop elements 12?

  I have the microscopic UI on my Lenovo Yoga 900 with Windows 10.  I have seen that this can be resolved by the UI scale to 200%, but no option appears under Edition > Preferences > display (or anywhere I can find).  Other suggestions are welcome - anything to redo my usable software.

  you run Photoshop elements 12, if you can't find it under Edit-> preferences-> display & cursors

  This feature is not available in 12 items

  The following 14

  

• Why Lightroom 6 continually freezes with 10 windows recently.

  Although it is completely happy with 5 Lightroom, I upgraded to 6 only because my new camera compact Olympus TG-4 did not had been supported in 5. For the past weeks 6 Lightroom has been almost completely useless in terms of being able to change anything before, it crashes and I had to go back to the previous version to have a usable software. Hoping that it is not a costly mistake?

  Hi xnalanx

  Adding to the suggestion of markl . Please save (using Adobe Photoshop Lightroom |) Back up a catalog) your catalog once before resetting the preferences of Lightroom. Refer to retrieve the catalog and images after resetting preferences

  Let us know if this helps

  Concerning

  ~ Assani

• Jumbo Frame on 1 Gig network

  Hello

  I'm using iSCSI based shared the storage configuration on the 1 Gig host connectivity, iSCSI, physical switch software and storage.

  Should I enable the jumbo frame on all devices of connection in order to have a higher flow rate?

  It will cause no problem as the connection to the store of data or something like that?

  Kind regards

  Sushil

  Allow executives to Jumbro for the IP storage is recommended, in any case may be a glance on the following link to see a few considerations and test results on the Jumbo Frames: Jumbo Frames comparison test with storage over IP and vMotion & raquo; boche.net & #8211; VMware vEvangelist