SWMagent keeps restarting on my laptop.

Similar Questions

• My laptop will not work, he said of updates step 3 of 3, but it is at 0% and keeps restarting itself. How can I get rid of this to open a session?

  My laptop will not work, he said of updates step 3 of 3, but it is at 0% and keeps restarting itself. How can I get rid of this to open a session? I tried the safe mode and do a system restore, which get rid of it. And suggestions? Thank you.

  Hello

  1. have you made changes on the computer before this problem?

  2. do you get an error code?

  Follow the mentioned article:

  Error: Failed to setup of the Windows updates. Restoration of the changes. Do not turn off your computer when you try to install Windows updates

  http://support.Microsoft.com/kb/949358

  Note that it takes as much time to do the upgrade as to reinstall the operating system. In addition, some of your custom Windows settings may be lost through this process.

  WARNING: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  How to back up and restore the registry in Windows

  Hope the above information is helpful.

• COMPUTER TOSHIBA LAPTOP KEEPS RESTARTING ITSELF

  Hello

  I HAVE A LAPTOP TOSHIBA WITH WINDOWS 7.  MY LAPTOP KEEPS RESTARTING ON EACH 30 MINUTES OR... I BOUGHT DEFEDER PRO 15-1 TO SOLVE THE PROBLEM, BUT I CANNOT COMPLETE THE SCAN BECAUSE OF THIS PROBLEM. BEFORE IT RESTARTS I GET THREE DIFFERENT MESSAGES IN A SMALL WINDOW THAT OPENS AND ARE FOLLOWING... "WINDOWS MUST NOW RESTART BECAUSE PLUG AND PLAY ENDED UNEXPECTEDLY", "WINDOWS MUST NOW RESTART BECAUSE THE SERVICE OF POWER ENDED IN UNEXPECTED WAYS ' AND ' WINDOWS MUST NOW RESTART BECAUSE THE FINISHED UNEXPECTEDLY DCOM SERVER LAUNCHER. I TRIED SCANNING IN SAFE MODE BUT STILL HAVE THE SAME PROBLEM.  ANY SUGGESTIONS ARE WELCOME. Thank you..

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forum for questions on Windows 7.

  Windows 7 questions should be directed to the it.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• computer laptop VAIO keeps restarting

  I bought my computer laptop sony vaio (model SVF15318SNB windows 8TM) April 2014 but on the month of August I have encounter a problem even now the laptop itself keep restart displaying the vaio icon but after restart 5 times or less he launched little windows. Fortunately, windows doesn't crash at all, but after 10 or 30 min it stop and restart itself. So, I look at sony nursery they check the Ram system, control the fan unfortunately, they do not find the specific target, they said that maybe it's the operating system that is causing the problem. Thus, they recover the windows. After recovery, the laptop works fine without problem. But after a few days the problem occur.so I take a recovery action after that and that during the system recovery itself close and restart this worst case is that the windows driver is impossible lock to update the system everything is lock

  I also ran the RAM, hardware scan both he could not find any error. Furthur consultation for the vaio Center care havnt done yet.

  So if there are suggestions please post and I will appreciate it.

  Hello Vishwaschangamayum,

  Thank you for believing in us giving the opportunity to help you.

  I can understand the level of frustration through which you are going. As you mentioned in your post that the problem began in August. Thus, there could be a chance that the problem originated on the Windows Update, released by Microsoft in the same month, as many customers were faced with the same question.

  These types of errors usually occur with a blue on the computer screen, when a serious problem causes Windows 8 to stop or restart unexpectedly. There are several reasons why this type of error occurs on the computer. They occur generally when there is some driver problems in the computer. However, it can be also a few other software/hardware reasons.

  Please refer to the suggestion provided by rvuerinckx replied on August 15, 2014 in the following thread.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_update/blue-screen-Stop-0x50-after-applying-update/6da4d264-02d8-458e-89e2-a78fe68766fd

  Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

  Thank you.

• Satellite P300 itself keeps restarting after the initial splash screen.

  My Satellite P300 itself keeps restarting after the initial splash screen.

  Start-up of the first screen with the F2 and F12 options down is displayed, the screen goes black, then a cursor appears in the upper left corner and flashes once or twice. Then the laptop stops and restarts and goes through the same process again and again.

  That's all with the power adapter is plugged in. If disconnected, he goes through the above process and close with no reboot.

  Any help or advice would be much appreciated.

  Post edited by: aic-poppy

  Start your laptop and enter the settings of the BIOS (F2). Set to its default value. Restart your computer, and press F8 to access the advanced boot menu.
  To start the laptop in safe mode and let us know if it works, try it please.

• Satellite M40 - 277 keeps restarting - button / stop?

  I have the problem that the (per hour to enter acient) laptop Satellite M40 277 of mine keeps restarting unpredictibally. Initially I have if it was a problem of overheating, so I used SpeedFan and CPU-Burn a test, but the computer does not restart until the airflow to the bottom is fine (I consider that the entry of the fan on the bottom a design error, but it's something else). Now, if the air flow is a bit stuffy, the laptop stops at about 83 and then it will have difficulty to challenge. Ok.

  However when the laptop is about 63C it restarts sometimes and I feel, it can be a power button is stuck. I have XP installation so that it will always ask before you actually stop, and when I pick up the phone on the side (the plastic box where the power button is integrated in waiting) I often question of the judgment. NP, just click away. But I also feel that the button can get stuck and then the system turns off after 5 seconds of 'holding company' the power button.

  So I just tried to get a quick glance and we should normally be able to remove the keyboard, but this M40 is a challenge. Even after that the keyboard is free, I don't see the actual power button.

  Is there anyway to loook under high elegant green rim the power button? How to open this thing up?

  Tom

  Hello

  As far as I know this little switch cover is fixed by 6 latches and connected with small flat cable to the motherboard. It just seems but if you don't know how to remove it you can damage these small latches and later you won't be able to fix the new.

  Anyway, if you think that this power button / troubled maybe just make the switch cover replacement may solve the problem.
  What say about it? Try to get the spare part and ask if anyone can exchange it for you.
  Of course, the best thing is to ask for professional help, but it will cool somewhat.

  Another way, do a risk and try to replace one.
  Let me know what you think of this.

  Good bye

• Satellite L655-1E3 keeps restarting in an infinite loop

  Hello

  It seems that I have installed an update of the BIOS not adapted to my Satellite L655 1E3. Now my laptop is never reach the Windows startup and keeps restarting in all about 3 seconds after the Toshiba screen display.

  What I tried to do is reinstall my Windows with the Windows CD: does not not when starting on the CD/DVD

  I still have access to my data located in the hard drive when I took it out of the laptop and makes a transfer on the other hard drive.

  Can you please help me and suggest me some ideas to do?

  > It seems that I have installed an update of the BIOS not adapted to my Satellite L655 1E3.

  I m wondering how could I know if you would try to update the BIOS to the version that is not compatible, the BIOS update procedure would be interrupted and it is not possible to Flash the ROM module
  That is why I think this might be the case.

  However, you said that you see the Toshiba start screen.
  Question: are you able to access the BIOS of the F2 keys?

  In the case where this is possible, the value of the default BIOS and try to start the machine again.
  Where this is not possible, remove the AC adapter and the battery.
  Press and hold the power button / stop along 30 sec. Then reconnect both sides and try to turn on the unit.

  Your comments and good luck would be appreciated

• Equium A60 keeps restarting after installation of the graphics driver ATI

  I have installed the Toshiba ATI graphic driver, but when I restart the laptop, it does not start, keeps restarting before surposed to go on windows XP. Help, please.

  Hello

  Try please solve it as described on this Microsoft article http://support.microsoft.com/?kbid=293078

  Generally, the display driver installation should help. As you know sometimes it is not easy to fix this kind of problem and sometimes is much better recovery procedure.

  You can not write about any common problem if you n t know exactly why this happens. If you are recovering the unit it will be working well. A negative influence on the graphic can have some games preinstalled or many other additional software.

• Satellite A305 keeps restarting

  I have a Satellite A305-s6857.
  Windows xp 64 bit vista.

  This is what is happening, please bare with me it gets really confusing. Laughing out loud

  My laptop keeps restarting on its own.
  at first I thought it was overheating - so I downloaded SPECCY and clean the radiator using carbon Spray. CPU temperature average around 60 degrees.

  so after ANOTHER REFORMAT. the computer worked fine, installed all the drivers using the recovery CD. (computer remained without restarting)
  everything worked well. After you have installed all the drivers, I restarted the computer and it came

  "your account has been disabled. Please contact your system administrater' so I went safe mode created an administrator account.
  Another thing to install TOSHIBA came after rrestarting the computer where I would choose an account name and password.
  so after that I got through the process, he went on the desktop.

  After that, he did it again. Computer keeps restarting, sometimes only takes a few seconds, sumtimes lasts 5 minutes.

  RELATED ISSUE: Tuner FM from Toshiba keeps repeatedly installation and restart the computer.
  then I went to msconfig and disabled everything on start up.

  I don't know much about laptops, but in MY OPINION.

  It is a software problem, VISTA/driver problem, if its vista I think it has something to do with the admin default thing, cus when I am connected to this account, that it has not been restarted.
  but when this thing "account disabled" came and I had to use a new user, he did it again.

  AND ALSO: When in safe MODE, the computer does not restart.

  someone please get back to me.

  Thank you
  Jason winter

  Hello

  > I have a Satellite A305-s6857 running windows xp 64-bit vista.

  What Windows environment it restarts: Win Xp or Vista or both?

  > so after a REFORMATER FEES. the computer worked fine, installed all the drivers using the recovery CD. (a computer stayed on without restart) everything worked fine. After you have installed all the drivers, I restarted the computer and it came

  It looks like a driver/driver causes reboot.

  > SECONDARY QUESTION: Toshiba FM tuner keeps several times install, then by restarting the comp. I went to msconfig and disabled everything on start up

  Can remove you it at all to check?

• iPod Classic keeps restarting. Already tried several solutions, I can find.

  My classic iPod keeps restarting randomly. Sometimes he can play for a few hours, other times its a few minutes.

  I got it over a year and he had a spare battery rise (by Apple), in December, but no problems until this week.

  When I plug in my laptop (Windows) it gets usually recognized and appears in iTunes but usually disappears iTunes but says still 'connected' to the screen.

  So far I have tried:

  -Reset the iPod. (sometimes it's very slow)

  -Restore iPod to the factory via iTunes settings.

  -Check MP3 files for MP3 Diags with MP3val errors. Deleted everything that could not be repaired.

  -Put the iPod in disk and search mode of disk errors. No error found.

  Is there anything else that I could try or nobody knows what could cause this problem? Thank you.

  Take a look at Re: corrupted iPod classic. If the device cannot read the part of a multimedia file, it can skip to the next track, but if he struggles to read other data that may cause a reboot.

  TT2

• MACBOOK PRO KEEPS RESTARTING ITSELF.

  Hello world!

  Now, I don't know if it's happening because of this macbook was good for me and my aunt (perhaps after a mobile phone rate business here in Australia) brought the laptop is supposed to be refurbished (ect)

  Now it keeps restarting itself which is annoying, because I'm working on it. I clicked open the report and this is what I got:

  Anonymous UUID: 95CFAC8B-1883-70D4-607F-AE56B9B3818D

  Sea 6 Jan 19:45:16 2016

  Panic report *.

  panic (cpu 1 0xffffff8014816df2 appellant): Kernel trap at 0xffffef7f962f7778, type 14 = page fault, registers:

  CR0: 0 X 0000000080010033, CR2: 0XFFFFEF7F962F7778 CR3: 0X000000000A966000 CR4: 0 X 0000000000002660

  RAX: 0XFFFFFF810F0CBAF8, RBX: 0XFFFFFF810F0CBD60 RCX: 0XFFFFFF810F0CBAF0 RDX: 0000000000000008 0 X

  RER: 0XFFFFFF810F0CBAD8, RBP: 0XFFFFFF810F0CBB60, IHR: 0 X 0000000000000001, RDI: 0XFFFFFF80DF2C4000

  R8: 0XFFFFFF810F0CBAF4, R9: 0XFFFFFF810F0CBAF8, R10: 0XFFFFEF7F962F7778 R11: 0000000000000000 0 X

  A12: 0 X 0000000000000002, R13: 0XFFFFFF80DF2C4000, R14: 0XFFFFFF7F96379250 R15: 0XFFFFFF810F0CBC30

  RFL: 0 X 0000000000010202, RIP: 0XFFFFEF7F962F7778, CS: 0000000000000008, SS 0 X: 0 X 0000000000000010

  Lack of CR2: 0xffffef7f962f7778, error code: 0 x 0000000000000010, CPU error: 0 x 1

  Backtrace (CPU 1), frame: return address

  0xffffff810f0cb780: 0xffffff801472ad21

  0xffffff810f0cb800: 0xffffff8014816df2

  0xffffff810f0cb9c0: 0xffffff8014833ca3

  0xffffff810f0cb9e0: 0xffffef7f962f7778

  0xffffff810f0cbb60: 0xffffff8014d01523

  0xffffff810f0cbbc0: 0xffffff8014cfed83

  0xffffff810f0cbd00: 0xffffff80147e1307

  0xffffff810f0cbe10: 0xffffff801472ef8c

  0xffffff810f0cbe40: 0xffffff80147139f3

  0xffffff810f0cbe90: 0xffffff801472429d

  0xffffff810f0cbf10: 0xffffff801480231a

  0xffffff810f0cbfb0: 0xffffff80148344c6

  Corresponding to the current thread BSD process name: WindowServer

  Mac OS version:

  14F27

  Kernel version:

  14.5.0 Darwin kernel version: Wed Jul 29 02:26:53 PDT 2015; root:XNU-2782.40.9~1/RELEASE_X86_64

  Kernel UUID: 58F06365-45C7-3CA7-B80D-173AFD1A03C4

  Slide kernel: 0 x 0000000014400000

  Text of core base: 0xffffff8014600000

  Text __HIB base: 0xffffff8014500000

  Name of system model: MacBookPro5, 5 (Mac-F2268AC8)

  Availability of the system in nanoseconds: 10

  Model: MacBookPro5, 5, MBP55.00AC.B03 of BootROM, 2 processors, Intel Core 2 Duo 2.53 GHz, 8 GB, MSC 1.47f2

  Graphics card: NVIDIA GeForce 9400 M, NVIDIA GeForce 9400 M, PCI, 256 MB

  Memory module: DIMM0/0 BANK, 4 GB DDR3, 1333 MHz, 0x80AD, 0x484D54333531533642465238432D48392020

  Memory module: DIMM0/1 BANK, 4 GB DDR3, 1333 MHz, 0x802C, 0x31364A54463531323634485A2D3147344D31

  Airport: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8D), Broadcom BCM43xx 1.0 (5.106.98.100.24)

  Bluetooth: Version 4.3.6f3 16238, 3 services, 27 aircraft, 1 incoming serial ports

  Network service: Wi - Fi, AirPort, en1

  Serial ATA Device: KINGSTON SV300S37A240G, 240,06 GB

  Serial ATA Device: HL-DT-ST DVD - RW GS23N

  USB device: ISight built-in

  USB device: Memory card reader internal

  USB device: Apple keyboard / Trackpad

  USB Device: IR receiver

  USB device: Hub BRCM2046

  USB Device: USB Bluetooth host controller

  Crush Bus:

  Refurbished Mac Apple is also covered under a 1 year warranty.  Call Apple technical support.

  

• P50T-B satellite keeps restarting randomly

  My laptop keeps restarting, so I lose some work if I'm in the middle of something. It was a very occasional problem, but now it becomes more regular. Someone at - it an idea what is the problem?

  I don't want to have to replace it under warranty as I put additional software on now.

  Thank you.

  Hello

  What exactly happens? What you think what could be the reason for this? I mean on this virtual path that none of us can say with certainty what could be the problem.

  Is machine hot enough when this happens? It happens when you use some specific software?
  You know there are several reasons why this can happen.

  Since when have you noticed such behavior of s to laptop?
  Try to provide some important information about your machine. Maybe this can help us understand what may be wrong with your machine.

• Vista keeps restarting after the installation of updates

  I have IBM laptop computer a customer T61, Vista Home Premium. Starts and goes to the "Configuring updates 3 of 3, then it goes to"shutting down"and keeps restarting."

  I tried safe mode, last good, from CD and repair of Windows, nothing worked.

  Any ideas on what else to do only a reinstall full?

  Thank you

  Ed

  Try this
  http://support.Microsoft.com/kb/949358

• HP Pavilion dv2000t keeps restarting...?

  My friend has a laptop HP Pavilion dv2000 and it was incredibly slow. Someone had installed a variety of free antivirus and firewall for them programs, but it seemed that there was still a virus somewhere and nothing turn scans. The laptop is used primarily for access to the internet and has not been inflated with the software. We decided that a new facility would be the best bet. I used my external hard drive to back up all the files that they wanted to keep and we used the recovery DVD (we had to order one of hp because the burned game could not be located) to reinstall Vista. Initially, he started not as I expected to (na not ask name of the administrator or the zone or something like that, but I tell myself it's because it's a "valuation" and not a new installation) and the task bar and start menu was set to classic mode (not a huge problem (, but I thought the default was aero). Now the operating system takes about 5 minutes before it restarts. We tried to disable automatic reboot in case of system error, but that doesn't seem to make a difference. I have a feeling that the virus survived the process of "valorisation" but I'm not sure. Safe mode seems to be stable. Any suggestions?

  Has nother thing interesting I discovered everything in tinkering with him last night is that the recovery process while retaining a (c) for only 24 GB, the total capacity of the HD is 160 GB. The optical drive is labeled (d) and there is no HP_Recovery partition, which I thought to be a factory default. On another laptop HP (dv6000) there are two partitions (C :) and (d), (d) being the HP_Recovery partition and the optical drive marked (e). The system continues to restart without any error message. Finally does anyone know if recovery disks (disk: this is a single dvd) are able to completely reinstall the operating system? For example if I used a live CD to completely erase the hard drive (overwrite with zeros or) can I still restore Vista with the recovery disk? Or part of the operating system should remain intact because it is just "valorisation"? Thank you,

  Leonard Ortega

  Message edited by clueless384 on 01/12/2008 11:36

  Yes we finally thought to it. It keeps restarting as part of the new installation procedure. I don't know why he has to do, but for some reason any HP needs to restart the system several times in order to get all the speed. Just start it upward and let it keep restarting, we had to let it run all night, so it may take a few hours. Just let it go, and it should work after that. Let me know if it works!

• Booted XP went into the mode options regurly of open windows, or knowledge last configuration or safe mode. No matter what I choose, keeps restart and return to this page

  Original title: frozen configuration page

  My laptop running windows xp pro was fine, when I went to bed last night, but this morning I woke and went to use the lt and it started as usual but then in a mode options regurly windows open or to last working configuration, or 3 safe mode options. And no matter what I choose, it keeps restart and return to this page and has continually repeated the same steps over and over again... someone can please help me with this?

  It seems that your XP hangs for some reason any...

  Why do we know almost nothing about your system (except a laptop with XP Pro)?  I know this isn't your fault...

  Please answer these questions and to implement the following:

  Provide information on your system, the better you can:

  What is your system brand and model?

  What is your Version of XP and the Service Pack?

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a working CD/DVD (internal or external) drive?

  You have a genuine XP installation CD bootable, which is the same Service as your installed Service Pack (this is not the same as any recovery CD provided with your system)?

  If there is a problem starting, XP is configured to automatically try to start again and you can stuck in a loop not being able to go beyond the screen boot options, or none of these startup options you choose will work only.

  Sometimes, when XP has a problem starting or falls down and tries to start again, it will give you a "short" menu of boot options and none of them will appear to be good to get your system going again.  You have tried them all!

  The options are similar to the Advanced Boot Options menu XP, but the only option that you need (disable automatic error system reboot) are not offered, because XP went too far during the boot process and offers a limited number of boot options.

  If this is the case, you must call Options menu advanced boot yourself until you do not see the option:

  Disable the automatic restart in the event of system failure

  When you get the XP Advanced Options correct start menu you want to see, he has options on it like these:

  Safe mode
  Safe mode with networking
  Safe mode with command prompt

  Enable Boot logging
  Enable VGA mode
  Last good Configuration known (your most recent settings that worked)
  Directory Services Restore Mode (Windows domain controllers only)
  Debug mode
  Disable the automatic restart in the event of system failure

  Start Windows normally
  Reset
  Return to OS Choices Menu

  You need to choose in this menu is the option:

  Disable the automatic restart in the event of system failure
  
  Then if XP does not start normally, you will see an error screen with information and clues about the problem and then you can decide what to do next.

  If you do not see the automatic restart on system failure option turn it off, you must reset your system and start typing the key F8 on the keyboard until you see her disable automatic restart on system failure option.

  If you miss the window of opportunity F8, you must try again and start tapping the F8 key with more urgency (earlier and more frequently) until you see disable automatic restart on system failure, and then select.

  You must keep trying the F8 menu until you see disable automatic restart on system failure option, and select it.

  If your system has a Blue Screen of Death (BSOD), we need to know what the screen says:

  Here's a BSOD example showing information you provide:

  http://TechRepublic.com.com/i/tr/downloads/images/bsod_a.jpg

  Send for the nose and the Red arrows (3 to 4 lines total).

  Send all * line STOP message since there are clues in the 4 parameters.

  If it looks like there is some kind of name listed in the STOP message file, send this line also.

  Ignore the boring text unless it seems important to you.  We know what a BSOD looks like, we need to know what your BSOD looks like.

  Answering queries and results report of the disable automatic restart on system failure screen and you can decide what to do next.