Synchronization between EBS and OID

Similar Questions

• Questions about the synchronization between output and analog input

  Hi all

  I now have a simple task which head a signal voltage (from PXI ao0) on a circuit and then your comments a voltage at the terminals of a component, for example, that one of the resistors in the circuit, through ai0 on PXI. So in this case, the synchronization between analog input and analog output must be made to avoid error of phase shift.

  I tried to build my VI by learning this example: https://decibel.ni.com/content/docs/DOC-3882

  However I have a few questions.

  1. I noticed that there is a merged error fed the "start task" sub VI for the analog output.  What is the point of fusion to mistake?

  2. I enclose my VI (also shown below) for the output voltage. I put my writing of DAQmx Subvi in the while loop so that I can change the voltage while the VI is running.

  

  However, in the example, the author has been reading outside of the loop and before even the start task. What difference will it make?

  3. I have also attached my synchronized VI. I always put the wavegeneration and the DAQmxwrite in the loop. A bulging guard error saying about samples is not available and needs to a higher sampling rate or a longer wait time. What causes this?

  I appreciate that these problems can be solved. Thanks to you all.

  (1) first you need start the task of acquiring, he'll wait for trigger here. And then you start the build task that provides this trigger. If acquisition could trigger and never start.

  (3) you must first write something in the buffer (writing DAQmx), then only you can generate it (Daqmx Start).

  Check Cont Gen tension Wfm - Int Clk - no Regeneration.vi in the help-> examples for example.

• Data impossible classic BlackBerry PIM synchronization between Outlook and classic

  I have problems to synchronize contacts and calendars between Outlook and my phone. I tried to uninstall and reinstall BB link but it doesn't give any help.

  As you use Microsoft Outlook 2016, I believe that Blackberry link has a compatibility issue with this version on the synchronization of contacts and calendars.

  System requirements: BlackBerry link for Windows

• Role of synchronization between OIA and IOM

  I am new to OIA and try to integrate OIA and IOM. My requirement is "role of OIA to the IOM of provision. My two IOM and OIA is at version 11.1.1.5.
  
  I am following the steps mentioned in http://docs.oracle.com/cd/E24179_01/ doc.1111 /e23377/integratingwithoimpreferred.htm #BABEFAAI. Step 3 (section 1.4.3) is very confused. It is said:-
  
  Connect to the Oracle Identity Manager Design Console.
  Open the form designer.
  For each resource, the following properties must be added to certain foods identified for import of accounts, policies and clearances:
  AccountName - identifies the single account in the target system
  ITResource - identifies the field of unique resource for the target system
  Payment - identifies the account reserved for the privileges attribute
  OIAParentAttribute - this property identifies the parent or the attributes of compulsory payment.
  
  Now what form it comes? I have only OID associated with forms like UD_OID_USR, UD_OID_RL, UD_OID_ROLE etc. It's because I have the autodeploiement to resource OID. In this integration, I should treat only IOM (xellerate) - user and IOM-role not to the resource of the DIO, right?
  I do not see the corresponding USR xellerate form available in the list of "Forms Designer".
  
  Help, please...
  Thank you!
  Kabi

  That's right, if you're not dealing with all resources like user OID just skip this section, in any case not required.

  I do not see the corresponding USR xellerate form available in the list of "Forms Designer".

  Do not map the details of identity using a form so there is no form. When you say that you have completed the document I believe you already have section * 1.4.2 step 2: modify the Oracle identity analytics Configuration files *. Thanks to the integration, synchronization would automatically create identities to OIA of IOM with some default attributes. In the same section of the instruction 3 * 3. (Optional) * talks about adding some custom attributes for IOM UDF etc.

  So if you come to skip step 3 with all the things in place and try to run the synchronization via step 6 you should be able to synchronize identity information and the role (links below)

  * 1.4.6.6 import roles *.
  * 1.4.6.7 import users * +, accounts, group memberships of user roles and rights.

• ICX session sharing between EBS and ADF. Navigate from EBS page by page of ADF custom application. but every time I get the session as a GUEST, even if I give valid credentils to enter into EBS.

  Hello

  I am integrating EBS and ADF through sharing of session ICX. Navigate from EBS page by page of ADF custom application. but whenever I get session as GUEST (VALID_GUEST), even if I give credentials valid at the EBS system. I should get a valid session that I have connected with a valid user. As it it a VALID_GUEST that the status of cookie icx, back (he got newspapers/debug) and I am.  Comparing with status cookie VALID icx, so every time system opens the Apps login page.  I used fndext.jar to do this. Please help me on this. I'm not sure it's a problem with DB/EBS EBS system, or the code of the adf. My code spruce is given below.

  import java.io.IOException;

  import java.sql.Connection;

  import java.sql.SQLException;

  Import javax.faces.application.FacesMessage;

  Import javax.faces.context.FacesContext;

  to import javax.servlet.http.HttpServletRequest;

  to import javax.servlet.http.HttpServletResponse;

  Import oracle.adf.controller.v2.lifecycle.Lifecycle;

  Import oracle.adf.controller.v2.lifecycle.PagePhaseEvent;

  Import oracle.adf.controller.v2.lifecycle.PagePhaseListener;

  Import oracle.apps.fnd.ext.common.AppsRequestWrapper;

  Import oracle.apps.fnd.ext.common.CookieStatus;

  Import oracle.apps.fnd.ext.common.EBiz;

  Import oracle.apps.fnd.ext.common.Session;

  / public class MyCustomPhaseListner implements PagePhaseListener {}

  public MyCustomPhaseListner() {}

  Super();

  }

  AppsRequestWrapper wrappedRequest = null;

  HttpServletRequest request = null;

  HttpServletResponse response = null;

  String currentUser store = null;

  String currentUserId = null;

  {} public void afterPhase (PagePhaseEvent pagePhaseEvent)

  If (pagePhaseEvent.getPhaseId () == Lifecycle.PREPARE_RENDER_ID) {}

  System.out.println ("in phase");

  If (wrappedRequest! = null & &)

  wrappedRequest.getConnection ()! = null) {}

  try {}

  If (! wrappedRequest.getConnection () .isClosed ())

  wrappedRequest.getConnection (m:System.NET.Sockets.Socket.close ());

  } catch (SQLException e) {}

  }

  }

  }

  }

  {} public void beforePhase (PagePhaseEvent pagePhaseEvent)

  If (pagePhaseEvent.getPhaseId () == Lifecycle.INIT_CONTEXT_ID) {}

  Channel agent = null;

  System.out.println ("forward Phase");

  FacesContext fctx = FacesContext.getCurrentInstance ();

  request =

  (HttpServletRequest) fctx.getExternalContext () .getRequest ();

  answer =

  (HttpServletResponse) fctx.getExternalContext () m:System.NET.FtpWebRequest.GetResponse ();

  CookieStatus icxCookieStatus = null;

  try {}

  Connection EBSconn = ConnectionProvider.getConnection ();

  EBiz instance = EBizUtil.getEBizInstance ();

  wrappedRequest =

  new AppsRequestWrapper (request, response, EBSconn,

  (instance);

  A session = wrappedRequest.getAppsSession (true);

  tried with "a session = wrappedRequest.getAppsSession ();" / / do not return not of any session

  icxCookieStatus =

  session.getCurrentState () .getIcxCookieStatus ();

  Agent = wrappedRequest.getEbizInstance () .getAppsServletAgent ();

  If (! icxCookieStatus.equals (CookieStatus.VALID)) {}

  response.sendRedirect (agent + "AppsLocalLogin.jsp");

  return;

  }

  currentUser = session.getUserName ();

  currentUserId = session.getUserId ();

  } catch (Exception ob) {}

  ob.printStackTrace ();

  }

  FacesMessage message =

  new FacesMessage ("Session is:" + icxCookieStatus + "" +)

  currentUser + "" + currentUserId);

  fctx.addMessage (null, message);

  }

  }

  }

  Have you checked

  https://blogs.Oracle.com/jruiz/entry/adf_and_oracle_e_business

  https://blogs.Oracle.com/jruiz/entry/adf_and_oracle_e_business2

  http://www.Oracle.com/technetwork/tutorials/EBS-SDK-ADF-1887167.PDF

  https://www.YouTube.com/watch?v=9wGv7yxRgVU

  Timo

• Notes of synchronization between icloud and on my mac

  I'm under El Capitan on my MacBook Air and use a lot of Notes. My notes are mainly on iCloud, but I wonder if there is a way to automatically sync local copies iCloud notes? The problem with out having only in iCloud, is that if I am where I cannot or would rather not log in iCloud, I can't work on my notes. In comparison, of MS OneNote synchronizes local and OneDrive versions of their notes.

  Also, how can one know if there are upgrade notes? Watch as they have always done mine.

  You should be able to work on your notes and they will re-sync when connected to iCloud.

  Information about the upgrade

• Synchronization between XP and Win8.1, both on FF 32.0.1 does not work, why?

  I'm trying to get the new synchronization to work. I have two machines, one XP and other Win8.1; both have FireFox 32.0.1 (and say they are completely up to date).

  Sync on each machine goes to the same account. 'Manage' the settings are the same. The machines are on the same network segment.

  I get to the point where I believe that this is the case: "After log you in, Firefox Sync will begin synchronizing your information on your devices connected.", but nothing does.

  Why am I missing a step, a button, some security settings?

  Whereas, my thought is that Sync has not been installed on this PC yet.

  When you click the button open the Menu ' 3-bar ' , which appears under the white area with the icons above to customize?
  Sign in to Sync?

• I can't synchronize between Android and the Office

  I configured the synchronization of my office. I have an Android device. As near as I can understand, I must now go for the Droid and perform the routine of Sync. This will give me a code I have then (I think) put on the desk. The problem is that aid tells me to run the Sync routine since the start page of the Droid. Well, there was one when I started, now it disappeared. I can't understand how to recover this Sync routine on the droid. The help file says it must be on the start page. But when I launch Droid of Firefox, it gives me a search bar, the 'Top Sites' I visited and - downstairs - Add-ons completely useless for your section of Firefox. How can I get the Sync routine appears on the Droid so I can actually run?

  I'll post my response. Basically, the option to set up sync on my Android never reappeared and I could never find. So I uninstalled Firefox since the Droid, re-installed and the option is back. I ran the routine, got the code, put it in my office and voila!, they have been synchronized. It seemed pretty much my only option.

• Possible bug-> CompactDAQ synchronization between HAVE and counter - sync error depends on the sampling frequency (exactly).

  I have a system with a map of the 9234 compactDAQ 4 Groove and a 9401 in slot 5.

  I use a function generator to create a 5V square wave frequency sweep.

  The frequency of scans from 1 Hz to 10 Hz in 3 seconds.

  I have this tee in my door to counter 0 (PFI1 - 16 Pin) and an analog input channel 0.

  In LabView, I do a period measure counter that has a trigger defined on the trigger to start ArmStart HAVE.

  Piecemeal the signal into two channels, I see the time counter correspond to zero-level positive slope crossings in the data to HAVE it.

  By the presence of a square with a mutation frequency wave, I know for sure that the time is not out of a period.

  I noticed the downturn to take samples, the greatest moment of the synchronization error.

  Here is the data that I have saved:

  sampling rate 1 / (sync error times)

  51200 1250

  25600 625

  10240 256

  2048 51.8

  1651 37

  It worked of Y = 0,0244 X + 1.1262 with R ^ 2 = 1.0

  So it could be, I have a programming error, or that there is a bug in the hardware or the base software.

  Thanks for any help to understand this question.

  BTW, I use this system to make an analysis program in the stopped vehicle with direct sequence over time - of course analysis based on the revolutions.  I found that order analytical tools was not flexible enough for what I had done, so I started from the ground upward.

  Hi Greg,.

  Looks like you see the entry delay the NI 9234 (Group delay).   As specified in the instructions for use NI 9234, entry delay is equal to 38.4 / fs + 3.2us.  This is because of how the sigma delta ADC works - after the start, it must acquire a certain number of samples before returning the first valid sample.  This delay is expected.

  Here is a knowledge base on the subject.  There are a lot more, just do a search of the knowledge base for "group delay.

• Synchronization between desktop and mobile Outlook

  I would like a place to work from and synchronize with my laptops and desktop.   It was a challenge that I travel a lot.  There are 2 of us who would use a calendar and tasks, maybe 3.   We want to use Outlook and share contacts and calendar as well.  We do not use Microsoft Windows Live Hotmail or Microsoft Office Live Mail accounts.  Please let know us if your service is suitable for it and what the costs are.  We are looking for the most cost-effective method and checking in MS Exchange server, the costs were astronomical.
  Thank you for the support.
   

  Outlook:

   

  http://www.Microsoft.com/Office/Community/en-us/flyoutoverview.mspx

  Office newsgroups

  http://www.Microsoft.com/Office/Community/en-us/default.mspx?DG=Microsoft.public.Outlook.General&lang=en&CR=us

  Discussions of general issues of Outlook.

  They will help you with your Outlook questions when repost you in the Office discussion groups above.

  See you soon.

  Mick Murphy - Microsoft partner

• BlackBerry smartphones synchronization between BB and MS Office - "Unable to open default folder in the group"

  Has been able to sync without problem before Christmas.  Copied personal records on memory stick, then to the laptop.  Return process, reverse, Overwrite original files.

  Now unable to complete sync process and do not know what is happening.  Believe the items entered in Schedule BB have been removed in the synchronization process, but no message appeared to support.

  Software problem?  Restart the computer?  Reload the software?  Others?

  If the software, please give a link to the current version of the software for BB 8800.

  Very welcome thoughts.

  Hi and welcome to the forums!

  Here is the info about your error message.

  Basically, you want to try remove the intellisync folder and reconfigure the configuration settings.

  If the problem persists, you may need to remove specific databases on your device.

  Thank you

  Bifocals

  http://www.BlackBerry.com/BTSC/search.do?cmd=displayKC&docType=kc&externalId=KB03093&sliceId=1&docTy...

• use of the port between db and OID

  If my database with ldap.ora makes a request to the OID ldap, it communicates with the ldap Protocol (3060) or ldaps (3061)
  
  What is the Protocol and port on the way back from OID to DB?
  
  is this /ldaps ldap or tcp/ip and does go to the listening port?
  
  
  Environment:
  ------------------
  
  Databases on 11 GR 2
  
  LDAP.ora on databases:
  
  default_admin_context = "dc = mydomain, dc = com"
  directory_servers = (oid.mydomain.com:3060:3061)
  directory_server_type = OID
  
  
  OID 11.1.1.4.0
  with the repository on 10.2.0.5.0
  
  
  Kind regards
  
  Peter

  Peter wrote:

  What is the Protocol and port on the way back from OID to DB?
  is this /ldaps ldap or tcp/ip and does go to the listening port?

  LDAP is a protocol of application. As is Oracle SQL * Net, SMTP, FTP, IMAP, and so on.

  Application protocols running on a wire protocol. Generally used wire protocols are TCP and UDP. (protocols in the suite of protocols IP/Internet Protocol)

  LDAP use TCP protocol. Trivial FTP (tftp) use UDP. Etc.

  Oracle Listener uses mainly TCP - don't remember having seen the listener supporting / using UDP. The listener to turn "supporting a number of application protocols - such as Oracle Net, WebDAV, HTTP and so on." (the listener itself does not use these application protocols - incoming TCP connections are reset to the Oracle server process and these 'speak' this specific application with the client TCP protocol).

  A customer talk application LDAP over TCP protocol to a Server LDAP (for example the OID).

  A customer can talk the application Oracle Net over TCP to the Oracle server protocol - and if that customer is a LDAP server, it will always use the client default protocol Oracle Net to communicate with the database server.

  Remember that the client-server is a s/w architecture - and s/w can be a server (for example, the LDAP server) and a customer (for example the client database Oracle).

• Synchronization between Windows and iOS

  I've used PhotoShop Elements on Windows for quite awhile.

  I make heavy use of key words.

  Now we have a couple of iPads, iPhones, etc.

  I'm looking for an app that will benefit from the investment I made in keyword tagging with PSE under Windows.

  I would like to be able to get all my photos to my iPad. Then, perform a search by key words in a manner similar to

  what I do now in organizing PSE. Also, it would be great if the albums I have on the EPS can be viewed on the devices as well.

  Creative cloud is maybe a solution that could do this? I think I'll probably continue to do most of my editing on Windows.

  So I don't think that I need a lot of editing on iOS. I want to large display and organization capabilities, however.

  Thanks for all the tips of thoughts!

  Yes, I use the iTunes sync PSE Album now.

  That works very well for basic albums.

  It does not support the smart Albums.

  This is a limitation.

  The iPad has a fantastic screen.

  The interface is really nice and friendly.

  I can find all kinds of applications on the iPad for photo editing.

  But for the Organization, I guess that I've simply become spoiled by the organizing power of PES.

  I have not found an Adobe or any other application that will do that.

  I tried to Revel. It allows the creation of tags 'event '. And Albums.

  But if there is something revel who focuses on existing metadata, I of course could not find.

  It seemed that I could see my library in a sort of 'All media' view.

  Or view where the images are ordered by date.

  Maybe the update of Windows support will add this feature?

• Relationship between users and roles OID

  Hi team,

  We have created users and roles in the IOM and the synchronization of these OID values. Users and roles create under different containers in OID.

  We have the relationship between users and roles of the IOM. How the relationship between users and roles are maintained in the OID.

  Could you please help me on this. Thanks in advance.

  Thank you and best regards,

  Narasimha Rao

  For 11 GR 2 IOM, roles map to the OID groups if there is a ldap synchronization (between IOM and the OID). I know that it works for IOM 11.1.2.2 and OID 11.1.1.7 (also 11.1.1.6 OID as well).

  Between the IOM and the OID ldap synchronization will automatically synchronize users of IOM in OID. So if you add a user to the IOM it will come in OID under the users container.  You create the role of IOM, you should see a group created under the OID. Similarly, if you add users to the IOM for a role of IOM, it will map/synchronization user in OID OID group.

  (Hope this helps, please indicate your answer as answered if it solved your query)

• Synchronize the values of variables of substitution between Essbase and planning

  Hello
  In EMP 11.1.2.1 version (but we noticed the problem also in previous versions of EPM) when we set the value of a variable substitution in Essbase, the value is not immediately updated in planning: for a while, we see the old value. The value in the planning remains unchanged even to disconnect or exit planning and reconnect.
  On the contrary if we restart the planning service, the value is immediately updated
  Since we would like to use the Essbase substitution variables to manage some selections in forms of Entru data planning, is it possible to force a synchronization, or increase the frequency of synchronization between Essbase and planning?
  
  Concerning
  
  Francesco Quaranta

  Take a look at the definition of ownership of planning SUBST_VAR_CACHE_LIFETIME

  http://docs.Oracle.com/CD/E17236_01/EPM.1112/hp_admin/properts.html

  See you soon

  John
  http://John-Goodwin.blogspot.com/