T wr pix 6.3.1 or sh run pause

Similar Questions

• Outdoor access for users of PPTP on PIX

  Hello everyone I have a PIX 506 6.3 (5) software running and configured to accept PPTP VPN from outside connections.  It works very well, the PPTP users get a local IP address of the configured pool and can access inside the hosts as expected.  What I want now, is that PPTP users can access the internet from here like inside hosts using dynamic NAT to the external interface. On ASA5505 this is achieved by the same-security-traffic permit intra-interface and corresponding nat (outside) configuration (with IPsec-VPN-Clients, not PPTP). On the PIX with the PPTP clients, I can not get this result.  Is it possible somehow?  Thanks a lot for any suggestion, Grischa

  grischast wrote:
  Dear all  I have a PIX 506 running Software 6.3(5) and configured it to accept PPTP VPN connections from outside.  This works very well, PPTP users get a local IP address from the configured pool and can access inside hosts as expected.  What I want now is that PPTP users can access the internet from here just like inside hosts via dynamic NAT to the outside interface. On ASA5505 this is achieved by    same-security-traffic permit intra-interface and corresponding    nat (outside) configuration (with IPsec-VPN-Clients, not PPTP, though). On the PIX with PPTP clients I cannot achieve this result.  Is it possible somehow?  Thanks a lot for any suggestion,  Grischa
  

  Grischa

  Unfortunately no, it is not possible on the pix 506 v6.x running. The reason is that the feature you need is called "bundling", which is activated by using the command "permit same-security-traffic intra-interface". But it is not available on code v.6.x pix.

  It is available on pix v7.x code and leave, but unfortunately the pix 506 cannot be upgraded to code v7.x. The minimum pix model that can run code v7.x is a pix 515E.

  Jon

• PIX, pat and static

  Hi all

  I have a pix connect my Internet when you run pat. (only a single public address)

  I would like to install a mail server on my private network.

  do I need a second public ip address or can I make a static with port 25 on the same ip address add that my global nat?

  Thanks in advance

  Hello

  You do not need another public address to the internal mail server. You can simply create a static port using the PAT address as the global address to the static. For example, something like this should work fine:

  static (inside, outside) tcp host 25 25

  I hope this helps.

  Scott

• SNMP poll PIX VPN Tunnel

  I have a pix to the United Kingdom that connects via the internet to a VPN in Aus concentraiter.

  I have a network of monitoring box in AUS I want to query the PIX to the United Kingdom.

  The problem is that I want to follow the internal interface of the pix and have traffic go through the ipsec tunnel.

  It looks like:

  NMBox - FW - VPN CON - Internet - PIX-Inside

  I can see the connection udp hit the pix in the newspapers, but it does not appear the return circulation. The SNMP configuration outside the pix is:

  SNMP-server host 1.1.1.1 inside poll

  !

  someDodgeySNMPstring SNMP-Server community

  SNMP-Server enable traps

  Any ideas would be most appreciated :)

  Thank you

  Daniel,

  What you need to do is to activate your access to administration UK PIX (assuming your code of PIX is 6.3 +), inside interface that is

  (in config mode)

  management-access inside

  Now, if you ping inside the interface of Aus IP, you will get a response from the PIX. BTW, you can also run PDM now too.

  Hope this helps and pls rate messages! :)

  Jay

• SSH version pix 6.3.3 is the name of user pix, you can connect to?

  I test the SSH version 1 connections in a 515 6.3.3 I configuration of usernames within the pix and ssh allows connections via running ip address. THS problem is I can only connect to the PIX via the username "pix" and it will only allow one connection at a time.

  Does anyone know why not accept logings via SSH using user names defined in the device?

  Thanks in advance. Mike

  Enter the commands 'aaa-server protocol LOCAL local' and 'ssh LOCAL console aaa authentication. "

  You will then be able to connect using the local usernames on the Pix.

• VPN site to Site between 6.3 (3) PIX and PIX 7.0 (1)

  Hi all

  I am configuring a VPN site-to site between my office and a new site. This is my first time doing a real VPN site to site, in the past we have always just used MS PPTP VPN.

  My office firewall is a 6.3 (3) 506th PIX running, and unfortunately this can not be upgraded to 7.0.

  My new site has a pair of PIX 525 in a failover configuration, running version 7.0 (1).

  The only documentation that I could find on this subject is a http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a0080094761.shtml, which corresponds to an even earlier version of the software firewall (although orders seemed to be valid on the 6.3 software).

  I ran through the VPN Wizard in the ASDM on the new firewall of sites, and the output produced in the firewall rules is not really what I expected. Commands like 'ISAKMP key' have been depreciated and replaced by "tunnel-group.

  What I'm really after a pointer in the right direction for certain documents which covers this type of scenario, I can't be the only one trying the link between the different versions of PIX.

  Hi M8,

  In quick words, more of the config is always the same (sets of transform, ISAKMP policy, Crypto Maps and Crypto ACL).

  The only thing that changes is the:

  ISAKMP key * address x.x.x.x

  and it is replaced by the tunnel-group command:

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group ipsec-attributes x.x.x.x

  pre-shared-key *.

  you put the IP peer under the name of tunnel and as you can see, you will write the key in ipsec-attributes sub-mode.

  I see straight forward and I think that you will find it easy once you get used to the question of the tunnel-group.

  Hope that helps.

  Salem.

• Fleeing bad IPS

  Hi, when I set up a signature to block the action of the host connection, I see that the IP addresses are not fleeing the connection (TCP port), SPI block the host for all ports.

  I don't know if this is a normal action.

  The shun command display on PIX sho is the next

  Shun (outside) 200.122.333.213 0.0.0.0 0 0 0

  When I think that the display of the order is

  Shun (outside) 200.122.333.213 192.168.1.1 25 where '25' is the port that I need to block and 192.168.1.1 is the ip address of the internal server.

  Thanks for the reply.

  The Pix does not support the elusive connection.

  It supports full fleeing host.

  Be aware that the following two commands will be shun the 200.122.333.213 any address.

  Shun (outside) 200.122.333.213 0.0.0.0 0 0 0

  Shun (outside) 200.122.333.213 192.168.1.1 5555 25 tcp

  The first command lists only the address of the source, while the second lists information about a connection. Both, will, however, avoid the whole source address.

  The connection in the second command information do not limit the shun just in this regard. Rather just the Pix to use additional connection information remove this connection special it's internal connection table.

  Why is what is needed if the source is being avoided anyway?

  The first reason is little basis for cleaning the connection table.

  The second reason is to ensure that the specific connection is torn down. Without removing the connection from the connection of the Pix table there is a remote possibility that, after the sensor removes the shun command, that the connection will always be in the table of connection of the Pix. This means that in the event of an attack, the attacker may be able to continue his original tcp connection after the shun is deleted because the original connection is always in the table of connection of the Pix.

  He is briefly mentioned in the examples section of the presentation of Shun Pix commands:

  http://www.Cisco.com/en/us/products/sw/secursw/ps2120/products_command_reference_chapter09186a00800ec9eb.html#1026366

  Since the Pix itself does not support a connection shun, the sensor can only send host avoids the Pix.

  Sometimes these hosts run will contain login information and sometimes simply IP source address.

  But in both cases, it's still a host of shun.

  When he sends connection information and when it does not?

  When users select event host the Shun Shun actions is usually sent with the connection information. This is because the sensorApp shun request contains the connection information.

  When users select actions event connection Shun sensor winds usually sending a Shun with connection information (even if it ends in fact a Shun on the Pix host). It's because sensorApp shun request contains the connection information.

  When several shun connections are considered with the same source address, the sensor will modernize these occult connection deliberately to a complete host Shun. In this scenario, the host Shun is an intental upgrade and not a sensorApp shun asks. An update internal multiple connections, there is no connection for her information. SO, the sensor will send the shun with just the IP Source address.

  Right now it is actually considered a very low gravity bug that the sensor sends a connection Shun the Pix that winds upward being a host Shun.

  In the future versions of the sensor will not send the connection saves the Pix until they have been upgraded to host Shuns.

  There is low gravity because most connection leaks wind upward upgraded to host avoids anyway.

  When only fleeing on the Pix it is therefore better to simply use the event host Shun actions and not do event connection Shun actions since they end up the same as anyway.

  Now if you manage the routers or switches instead of the Pix, you can enjoy the ostracism of connection event actions.

• Opening of port (s) IPSec on perimeter router

  I currently have a PIX515E session behind a perimeter. This perimeter is connected to the Internet. It has configured ACL security. I want to do is use the PIX as a VPN endpoint and so need to open some ports on the perimeter router numbers to reach the PIX. I would use IPSec running mainly between the NCP and the PIX, but have no idea what to do with the ACL on the router. It's I would say "ip permit any fw - PIX" or should I say "permit tcp PIX - fw" Can anyone help with the port number is possible. Thank you.

  You must enable the following ports.

  ISAKMP - UDP 500

  IPSEC - ESP (Protocol)

  access-list 101 permit udp any host eq 500

  access-list 101 permit esp any host

• authorization for AAA and GANYMEDE unavailable server scenario

  I installed a PIX for users authentication for telnet and enable access. I have permission to install a subset of users can run only display orders. This set works as expected.

  The problem is when I simulate and network failure and try to get access the PIX console. I can't run the enable command because the command shall not be permitted. I have to use means of recovery of password to access the PIX. How to do this? Can I have permission to order processed locally? Can I associated with the command show a lower level of the priveledge? If so, how and how can I limit the user to this level of privilege (via GANYMEDE)? I confiscate doing?

  Thank you

  If the PIX is configured for GANYMEDE authentiaction and RADIUS server is unavailable for authentication, there is no way to rescue or get around this issue at this time.

  You can configure the pix to get back to local authentication if Ganymede is not available.

  Release then (I think 6.3 and above) who will be available.

• Unable to access the private key

  Someone knows what the message 'Cannot access private key' means when PIX starts?

  I'm running a PIX515 and I just upgraded to 6.3 (4). I'm reconfigure the PIX and currently it's nothing more than a very basic connectivity.

  Here's the start:

  ******************************* Warning *******************************

  Copyright (c) 1996-2003 by Cisco Systems, Inc.

  Legend restricted rights

  Use, duplication, or disclosure by the Government is

  subject to such restrictions as set out in paragraph

  (c) Commercial - limited computer software

  The rights to FAR clause 52.227 - 19 and subparagraph s

  (c) (1) (ii) rights to technical and computer data

  Clause of DFARS 252.227 - 7013 section software.

  Cisco Systems, Inc.

  170 West Tasman Drive

  San Jose, California 95134-1706

  address of the external interface added to the pool of PAT

  address of the interface added to the pool of PAT DMZ

  Cryptochecksum (Unchanged): xxxxx

  Cannot select private keyType help or '?' for a list of available commands.

  Pix1 >

  Thanks in advance,

  Doug.

  The pleasure is mine,

  Please close it as resolved, they removed the post from the list.

  Thank you

  Patrick

• VPN via a natted router

  Hello

  I think that vpn via nat is 'enabled' in the 6.3.1 software for the pix? I have problems to run. Can someone give me directions, including everything I need to know about the router?

  I guess that everything that I have to do is create a static nat from 1 to 1 of the legal IP outside the pix outside IP router? Then configure the vpn as usual to accept vpn as usual (I use the 4.0.1 cisco client).

  I'd appreciate any help.

  Thanks for your time

  Andy

  I think that you need to configure the NAT-Traversal, the command to do this is isakmp nat-traversal]

  NAT - T can be enabled or disabled:

  By default? OFF for site to site tunnels

  By default? We'RE for hardware and software VPN clients

• can I buy a device to download pix on my phone to free up space when I'm traveling?

  Can I buy a device to download my pix that I travel to free up space on my iphone 6

  Any laptop would work fine, but a better option may be to look with Dropbox or similar storage service online. Perhaps if you could provide more information on your plans and your needs we can offer other suggestions. How much space you have on your phone? How long will you be away from your computer at home? Any estimate on how many pictures will you take?

• FF 27 - my fonts are pixely and I can't understand why.

  Hello friends,

  About 4 weeks ago, fonts on all the pages I visit using Firefox became pixely (some letters appear in bold, the lines seem to be low resolution, etc.). I tried the following steps to fix without success:

  -Update of FF 27
  -Reset by default
  -Turn off hardware acceleration

  Here is a link to a comparison of the FF27 vs Chrome vs IE screenshot: http://i.imgur.com/f8EBC6p.png

  The only thing I can think of that may be the culprit, it is at the same time, I got a new monitor that requires a display installed on my laptop driver.

  What other troubleshooting measures can I take to help address the display of police while I use my beloved Firefox?

  Any help is appreciated.

  Thank you.

  Try to play with this:
  =

  layers.acceleration.disabled: True
  

  And make sure that firefox has the updated driver, you can check in "subject: support.

  and try turning off hardware acceleration: try disabling graphics hardware acceleration. As this feature has been added to Firefox, it has gradually improved, but there are still some problems.

  You will have to perhaps restart Firefox for it to take effect, so save any work first (e.g. you compose mail, documents online that you are editing, etc.).

  Then perform the following steps:

  • Click on the orange top left Firefox button, then select the 'Options' button, or, if there is no Firefox button at the top, go to tools > Options.
  • In the Firefox options window, click the Advanced tab, and then select 'General '.
  • You will find in the list of parameters, the checkbox use hardware acceleration when available . Clear this check box.
  • Now restart Firefox and see if the problems persist.

  In addition, please check the updates for your graphics driver by following the steps in the following knowledge base articles:

  • Troubleshoot extensions, themes, and issues of hardware acceleration to resolve common problems of Firefox
  • Update your graphics drivers to use hardware acceleration and WebGL

  This solve your problems? Please report to us!

  Thank you.

• Best approach and Apps to manage Pix taken on the iPhone and sync.

  Can someone direct me to articles or the spirit to give me a quick post re: a great way to manage my pix that I take on my iPhone 6 then organize into folders easily and have the synchronization of files to my other mobile devices and Apple computers? My iPad and iPhone are both on the same iOS but my computers are a little different: I always use Lion (10.7.5) on my Mac Pro and Yosemite (10.10.5) on my Macbook Pro. My equipment is:

  1. iPhone 6 (iOS 9.3.2)
  2. Air iPad (iOS 9.3.2)
  3. MacBook Pro (OSX Yosemite 10.10.5)
  4. Mac Pro (OSX Lion 10.7.5)

  Basically, I want to be able to create a folder of say on my iPhone and put relevant pix in it and have the folder synchronization and pix of my devices above. And if I were to edit or delete a photo on another device synchronization of changes to the other 3 devices. Key word is easily. The best analogy I just with that is IMAP for email, and whose changes are instantaneous and fluid to all other connected devices assuming that you use the same AppleID devices of course.

  Maybe it's me, but I find a bit intuitive Photo Apple application so thinking maybe someone has created a more robust application and intuitive that works on all the other computers and mobile devices Apple.

  I read reviews on App Store and Googling but thought maybe I'd get a stronger recommendation here among the Digerati Apple

  Thank you

  Steven

  the built solution just for this is iCLoud library except for the Lion system - there is no transparent and automatic solution for Lion do what you want

  iCloud Photo library FAQ - Apple Support

  LN

• Cannot find the backup store in DOCS n Toshiba drive external HARD to PIX

  Hi guys,.

  a few days back I have backup my loads of PIX and Documents TOSHIBA external HARD drive (3.5-inch USB 2.0 Black + Silver HARD drive, 2.5-inch USB 2.0 HDD Black + Silver) in-store "My PIX" and "My Documents" backup of your laptop. Now I'm trying to restore it on another laptop but I can't find them through TOSHIBA REGEN backup software. But first I couldn't find my music store of movies but the itch to get through 'repair catalogue' in the software... Has anyone asked similar problem as I do? Any help of suggestion will be highly appreciated.

  Thanks in advance!
  Nukesh

  Hello

  To be honest I m no owner of these HARD drives.
  But I wonder why you use the backup store to retrieve files

  Why you n t access HARD drive and just copy and past the files to another location