T61 screen became ballistic, now red and green.

I upgraded my xp pro to 7pro t61. read all the articles and I don't want to read about external sites and lenovo. I installed all the updates and Device Manager was perfect without any problem. There were originally, but lenovo community, I was able to fix everything.

Today, I got an ssd crucial m500 with 240gig. I was looking upward on u-tube and the lenovo site to make sure that I installed the new SSD correctly. just before my last article, the screen became lucky. red lines up and down the screen. I turned off the computer and then rebooted (hard coded with button / stop). the screnn has the same at the start and played the usual startup sound. I have attached an external monitor and the same result.

I read that the nvidia I have is a problem and, eventually, the card mother. I bought this new (t61 7662 cto) and love it. I like to keep this unit... it is a work horse. any suggestions... Thank you

I've never had a problem before and I'm very careful with the unit, not abusive.

Welcome to the forum!

I'm sorry to say that your T61 is another victim of the infamous "nVidia bug". A replacement motherboard will be necessary.

Good luck.

Tags: ThinkPad Notebooks

Similar Questions

  • Features red and green Qosmio F30-117 - display problems-

    Hello

    I have a qosmio F30-117, and until recently, I was thrilled with everything about it.

    Then, mid session, graphics started to deteriorate, which fixed a reboot.

    Then a few days later, he did it again and this time when I rebooted it came with a display corrupted, a lot of aa in all directions then red and green lines everywhere.

    Managed to get by selecting safe mode with network and got a desktop computer but still with red and green lines everywhere.

    Now its got worse again, when I start the screen of the laptop itself is empty, becomes something because it is not completely black as if it was when its engine turned off, but his Blanck.

    To check I have connected to an external monitor and managed to get again in safe mode with network, but still very bad and always red and green lines everywhere.

    I started to take a ride on the old good www and there are many posters and articles with problems and many mentioning the lines red and green etc...
    so I'm not alone, but no one seems to know exactly what it is.

    Some have mentioned the grateful Toshiba this as a problem and make even if out of warranty repairs.
    Thus, ideas, advice and does anyone know if Tosh have agreed the problem and offer any help?

    Thanks in advance

    Hello

    In my opinion, this looks like a problem of graphics card GPU eventually started to malfunction, and in this case to replace the motherboard.

    > Some mentioned Toshiba grateful that as a problem and make even if out of warranty repairs.
    Thus, ideas, advice and does anyone know if Tosh have agreed the problem and offer any help?

    It doesn't have to be dull I ve also found this update from Toshiba product support page, but there is nothing listed on the problems of F30
    http://EU.computers.Toshiba-Europe.com/innovation/generic/PRODUCT_UPDATE_SUPPORT

    What to say. Seems only a technician ASP might solve your problem, but replacing motherboard is a costly affair so it s your own decision to want to do

    In any case... good luck...

  • Toshiba 40L5441DG - Led shows red and green light

    My Toshiba 40L5441DG were now waiting for 72hrs, and the Led is showing red and green lights.
    I just bought 3 weeks ago... I need help pls.

    If I understand you right when you try to turn on your TV on the LED is green, but there is no pic, right?

  • 32W1333DB does not turn on - standby blinks red and green

    IV recently bought nine toshiba Led backlight LCD 32w1333db.
    can someone help tv doesn't turn on no tv or distance, standby flashes red and green...

    Thank you

    Unplug the power to the TV and wait a bit.
    Then reconnect and press the power button on the remote to power ON the TV.

    It work?

  • Windows Movie Maker, after the problem - red and green

    When I change my movie with Windows Movie Maker preview is fine, but after the publication of the project, the film is red and green. What can I do to fix this?

    I solved this problem. But I think it was because of the video quality of my webcam. Director of Windows try to enhance the video at the time of publication. So that's my new problem. Can I update my webcam as well?

  • RED and green flashing 1532 AP

    Hello

    I have a 5508 controller with internal antennas 2700 Series and external antenas. All work fine, internal APS APs green led and when someone connect turn blue.

    But with the external antenas, the led flashes green and red, I check the AP and is perfectly recheable of ping, is well recorded on WLC and have the user and EVERYTHING works fine! ...

    My question is what does flashing red and green?

    PD: the newspaper of WLC nothing shows up not bad

    Thank you

    your 2700 has enough power?

  • Red and green frames

    I work with first CS6. in my CS6-Projekt I imported an AVCDH Clip of my Panasonic HDC-TM700. An AVCHD Clip from a Canon camera, I had stabilized a color corrected and the new blocks to a H.264, HD1080i25.mp4 and also imported for my project. When I take this Clips to my timeline, I have red and green frames on my Panasonic AVCHD-original file. When I made this file I also have red a green frames in the new file.

    Why export a movie as a file and then re - import? You can always add an existing sequence in a new sequence (nesting) to make a new, less cluttered way of working. In this way made even frames red and green?

  • DeskJet 932C, Windows 7, a red and green light on the machine will not work

    Both my red light and green light are on and printer has stopped working.  What, on the contrary, do in addition to become another printer? When I press red light nothing happens. When I turn printer off and on again the same lights appear.  When I open the cover, nothing happens.  Should I throw away it and get a new one or can it be fixed?

    It seems that the camera is blocked in an error state.  There is a section in the user guide for the printer Deskjet 932C which covers when there are flashing lights.  I'll link this information below.

    The user guide can be found here.  Page 40 of the user's guide provides information about the error lights up on the product.  Follow the recommended steps and let me know the result.

  • The HP Omni100 5155 PC: HP omni100 5155 red and green lines on the screen

    I used a music cd in my pc one day and the next day I had thin green and red, vertical lines throughout the screen. I did a number of bugs, but the problem persists. I was wondering what I need to do or it sounds like a graphics card? Although I checked it and the message says: "the device is functioning properly."

    I tried the things:

    • updated drivers
    • scanned for viruses
    • cleaned the ram
    • memory diagnostic tool
    • update graphics card

    Sorry, for obvious reasons, I'm not here to sell you a computer.  Most of the all-in-one computer today have the specifications you are looking for, except perhaps the webcam integrated according to the model.  You can see the HP, Amazon or Tiger Direct store as examples.

    If you are looking to buy the same more or less the same model as you have now, they are abandoned or not available unless used or refurbished which I would not recommend it.

    Before doing something drastic, discover the repair costs to the one you have now.

  • The monitor shows red and green lines

    my laptop is to jump up and down with green and red lines through it

    original title: my screen jumps up and down and has green and red lines through it

    It is normally a sign of a graphics issue.

    Download the latest graphic drivers:

    Go to the website of the manufacturer of your computer/laptop > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

    If the problem persists on board graphic Hardwarre could be at fault.

    Contact the manufacturer of the laptop computer,

    See you soon.

    Mick Murphy - Microsoft partner

  • Small yellow, red, and green bars next to the names of the participants

    This indicates their connection is good or bad, or their participation in the meeting?

    I had heard both and I don't know what is is now.

    Thank you!

    They used to be an indiction of what the user said their bandwidth was (green = equal to or greater than the bandwidth setting room, yellow = a length less than the bandwidth of room setting, red = two steps below the room bandwidth setting). But since nobody never set their bandwidth at a level of lowe, and he was never automatic bandwidth detection, this function disappeared with Connect 7 (I think). Now, this is related to the nacelle of the commitment, if you have access and will show the participation (read that focus the Connect room on their computer) in the logon session.

  • My computer screen (flat screen) shows the colors Blue and green neon.

    What can I do to solve this problem.  My resolution is higher than 32 bit.  I'm on Vista.

    Hi Zululand,

    Thank you for your message.

    "BLUE COLORS ARE COMING BEHIND MY PHOTOS AND MY ICONS"

    This happens anywhere else outside the office, where are your icons?

    Here is an article on the reinstallation of the drivers:

    http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

    See the section "manually install the drivers' specifically.

    Even if the driver says it's OK for the graphics card, I would like to reinstall it.


    Chris
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • How can I fix the system to show red and green colors to customize (you are looking for all colors)?

    Preium Running Windows Vista Home Edition, Service Pack 2.  Currently only display black, white, gray, yellow, blue & Brown under START - control panel - appearance & personalization - customize the colors.  How can I fix system to show "all colors".  Note: This affects all MicroSoft applications as well.

    Hi Martin,

    To provide the proper resolution, I would need more information on your side.

    1. you are trying to change the color of Windows?

    You can read the article and check if it helps.

    Change the colors on your computer
    http://Windows.Microsoft.com/en-in/Windows-Vista/change-the-colors-on-your-computer

    Check out the link for more information.

    Customize your computer
    http://Windows.Microsoft.com/en-in/Windows-Vista/personalizing-your-computer

    Hope this information helps. Answer the post with an up-to-date issue report to help you further.

  • When I use tilt-shift filter red and green ghosting occurs

    TiltShift.gif

    In fact, all the new blur filters exhibit this behavior.

    How should I do?

    I fixed it. 'Coder CL' power in the graphics processor options off advanced.

    No thanks to chat online Adobe ;)

  • Re: Pink and green screen on the Satellite X 200

    A difficult for all a... my laptop screen is a nice pink and green but if I connect to my TV via HDMI, it works perfectly
    Thank you
    Trevor

    >... but if I connect it to my TV via HDMI works perfectly
    You did very good test. Graphics card is correct and troublemaker is LCD.

    On eBay you can find fairly cheap.
    Can share you one?

Maybe you are looking for