Target iscsi ESXI 5.0, active path connected, mounted, are not not in the data store data store
HI -.
I am looking for help to point me in the right direction. This problem occurred after a reboot of the system.
I'm in vmware esxi essentials 5.0.0 821926
I use the starwind software as my iSCSI target
I use ISCSI to connect to my server from storage to the esxi hosts.
I have 2 warehouses of data showing inactive under clusters of data storage and the data store. I have a third-party data store on the same server that is loading properly.
I currently have the same behavior on three esxi hosts:
under configuration - storage adapters is the ISCSI path is active. Data warehouses appear under devices and mounted. In data warehouses, they are inactive. On the same storage server
on the starwind Server - I have
built a new target
removed and added the databases to the new target
Changed the IP address of the target.
On Esxi hosts, I removed the ISCSI server, discover places BOF dynamic and static and added under the same or IPs news discovery
I can restart esxi hosts & storage servers and get to that same point.
Whenever I find myself in the same place - course assets, devices mounted, inactive in data warehouses
I don't know what else to share, let me know what you need to know to help out me.
Thank you
Dylan
OK, incase someone crosses my ramblings, it may help. My original question was warehouses of data that would not rise. They were visible as devices in the area of storage under devices and as devices in the scsi adapter.
When I would try to force mount them, add storage, keep the signature, mount they wouldn't mount. I did some research and my question was after a failed mount attempt strength as got data attached as snapshots warehouses. I then mounted force them and he tells will data warehouses and I got them back.
I followed this KB to identify and resolve the problem
manipulation of vSphere detected as snapshot LUN LUN (1011387)
When it was over, I tried to add vms back and found a new show. Power of vms would expire. the vmkernel.log showed;
2014 05-27 T 07: 20:40.010Z [verbose 'Vmsvc' 564D7B90] Vmsvc: filtering Vms: ignored not ready to request power state vm vim. VirtualMachine:75
AND
(2014 05-27 T 03: 45:47.821Z cpu4:2052) NMP: nmp_PathDetermineFailure:2084: SCSI cmd RESERVE failed on the vmhba35:C0:T1:L0 path, booking on eui.cff548d1952b1e4c of device status is unknown.
I had latency huge read write showing upwards, 3K and more
After several searches, I had in the ESXShell and found that there is no conflict of booking.
On a whim, I took inventory all virtual machines that are now inaccessible. I then added a DOS virtual machine. Alto! the latency down to version 1.2 a.7 ms for all data warehouses.
ultimately the instructions said you may need to add virtual machines in the inventory, but does not remove all virtual machines first. I was grabbing vms that were not in stock, so I didn't remove the old virtual machines in the inventory.
A recruit Mennonites, Yes.
Tags: VMware
Similar Questions
-
Hello
Below for the output of my blade IBM HS22., are there any problems with the configuration of the path.
List of paths esxcli storage nmp
SAS.5005076b08b7aaa4 - sas.a9501097faba7a - naa.600508e0000000007abafa971050a900
The Runtime name: vmhba0:C1:T1:L0
Feature: naa.600508e0000000007abafa971050a900
Full device name: FREE Serial Attached SCSI (naa.600508e0000000007abafa971050a900) drive
Group status: Active
Table priority: 0
Storage Array Type Config path: ATAS VMW_SATP_LOCAL does not support the configuration of the path.
Path selection policy path Config: {current: Yes; favorite: Yes}FC.2fff0000c900009f:2ffd0000c900009f - fc.500507680100 b b 680 680:500507680130 - naa.60050768018105afc000000000000df0
The Runtime name: vmhba2:C0:T3:L2
Feature: naa.60050768018105afc000000000000df0
Full device name: disk of IBM Fibre Channel (naa.60050768018105afc000000000000df0)
Group status: Active
Table priority: 0
Storage Array Type Config path: ATAS VMW_SATP_SVC does not support the configuration of the path.
Path selection policy path Config: {current: Yes; favorite: Yes}Kind regards
Surya
Hi Surya,
No, it's not any problem with the configuration of your path.
It only means that this policy does not allow additional configuration.
I.e. with fixed NMP, you would be able to configure a preferred path allowing you to manually distribute the i/o load.
Your current configuration does not offer this option.
Kind regards
Ralf
-
Hello!
After the end of my second day of test error, I put this question on the table:
I use ArraytoChannels function to store ADO recordsets as strings. What is strange, is that for the first Recordset, it works; but for the next time through the loop, it always fails with the error message 'cannot be added because the channels of the target are not all the same length.
I confirmed that:
the RowData sizes and the ChannelNames are equal,
both spend the isarray = true test,
I change the order of the ChannelNames,.
I have reconnected/disconnected from the oConnexion every time, nothing has changed.
Apparently I'm missing something - but crazy to know what! -If anyone can share his opinion I'll so much appriciate. Here is my code:
oTables = Array ("WellStates", "ChokeData", "WellParameters", "FlowData", "PumpData", "SensorsData", "ModelCalculatedData")
Call OpenSQLConnection
Set oRecordset = CreateObject ("ADODB. Recordset')
Call SelectWell
Call GetWellStateIDsData.Root.Clear
for j = 0 to ubound(oTables,1)sSQLSting = "select * []" & oTables (j) & "] where [WellStateID] between" & WellStateIDFirst & "and" & WellStateIDLast ".
oRecordset.Open sSQLSting, oConnexion
Protected oFieldNames: table: ReDim oFieldNames (orecordset. Fields.Count - 1).
for i = 0 to orecordset. Fields.Count - 1
oFieldNames (i) = orecordset. Fields.Item (i) .name
next
oArray = oRecordset.GetRows (-1, 0, oFieldNames)
Set oGroup = Data .root .ChannelGroups .Add (oTables (j))oArray, oFieldNames arraytochannels
oRecordset.close
oConnection.Close
nextSub GetWellStateIDs
sSQLSting = "select * from [WellStates] where [wellid] =" & WellID
oRecordset.Open sSQLSting, oConnexion
oArray = oRecordset.GetRows)
WellStateIDFirst = oArray (0,0)
WellStateIDLast = oArray (0, ubound(oArray,2))
oRecordset.close
EndSubSub OpenSQLConnection
Set WshNetwork = CreateObject
oComputerName = WshNetwork.ComputerName
oDB = "MX2. Player.DB ".
Set oConnexion = CreateObject ("ADODB. Connection")
oProvider = "Provider = SQLOLEDB.1; Integrated Security = SSPI; PeoExecuteist Security Info = True; Data Source ='
oProvider = oProvider & oComputerName & "\MX; Use procedure for prepare = 1; Machine translation = True; The packet size = 4096; Workstation ID ="
oProvider = oProvider & oComputerName & " Use encryption for data = False; Tag with column collation when possible = False; Initial Catalog ='
oProvider = oProvider & oDB
oConnection.ConnectionString = oProvider
oConnection.Open
EndSubAnother clue. If you check using DIAdem
Microsoft Windows Script Debugger
you are able to install the debugger in DIAdem.
It would potentially have shown that the command does not work as expected.
Sorry for the inconveniance
Andreas
-
Get the message "the network connections folder could not retrieve the list of the network adapters on your Machine. Please make sure that the network connections service is enabled and running. "I am NOT able to connect to the internet please help. I use Windows 7 OS
Hi Odile,
Thanks for posting your question in the Microsoft Community forum.It seems that you have a problem with the connection to the Internet and receive the error message "the network connections folder could not retrieve the list of the network adapters on your Machine. Please make sure that the network connections service is active and running".
I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.I may need a few more details to better understand the issue.
1. did you of recent changes on the computer before this problem?
2 do you have wireless or wired Internet connection?Method 1:
We'll first run check network troubleshooting if this can help.Using the troubleshooter from network in Windows 7
http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7Method 2:
If the problem persists, I suggest you try the procedure described in the article and see if it helps.Wireless and wired network problems
http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1Method 3:
If the problem persists, I suggest you try the procedure described in the article and see if it helps.How can I troubleshoot network card?
http://Windows.Microsoft.com/en-us/Windows7/how-do-I-fix-network-adapter-problemsFor more information, please see the link.Why can't I connect to the Internet?
http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-InternetGet back to us and let us know the State of the question, I'll be happy to help you. We, at tender Microsoft to excellence. -
I have Macbook & Office XP connected to the printer (HP Officejet 5746 e-all-in-one printer) necessary to connect Random cell phones to print the data. All directions? TIA Doc
You need a wireless setup to print from Android phones.
Please see this link for mobile printing options available:
http://www.HP.com/go/mobileprinting/
WyreNut
-
my Apple Watch does not record the data of my activity on my iPhone. The application of the activity is implemented on my watch and twinned with phone and not yet to record data.
HI - try the following steps:
On your iPhone close application of activity and also, if it runs in the background, the health app (you can close open apps, including the app shows):
-Double-click the Home button, and then drag upward on each of the app previews to close.
It can help to restart your iPhone and your watch. Turn on both devices off the power together first, and then restart your iPhone before restarting your watch:
-To switch off your watch: press and hold the button side until you see the cursor off the power; slide it to turn off;
-To switch on: press and hold the side button until you see the Apple logo.
If this does not resolve the problem, try next disconnect and rematching of your watch:
-L'app shows on your iPhone shows backups automatically, including a new when the unpairing via the application.
-Choose to restore the watch (backup restore) when provided the opportunity during the whole.
-Most of the data and settings will be restored, with a few exceptions (for example cards Pay Apple, access code).
-
The following files are not on the system: not a path >;
I tried to install several is based on different machines, but I have the following error:
The following files are not on the system:
Details:
CDK_Build_Invoke.VI.ProxyCaller > CDK_Build_Invoke.vi > CDK_Engine_Main.vi > CDK_Engine_PreBuild.vi > CDK_Engine_FileExists.viI've done several front facilities on the same project, I'm not sure what I could do to make it appear suddenly. Has anyone else seen elsewhere? How can I know which files the installer needs?
See this article: not a path error received when building an installer.
-
WRT1200ac and WRT1900ac OPENVPN can connect but can not see the network
I can connect but can not see the computers on the network. I've tried everything. Any help would be great. Thank you
Firewalls are disabled on remote computers?
-
How to find computers that are not on the domain in an Active Directory forest.
Hello
I'm looking for a tool that can scan a subnet and give me the list of computers that are not on the field, but connected to the network. My company has recently spent a lot of users of the task force to the area, but there is a population of users who are unwilling to join the domain and still using the local administrator to log on to the computer.
These computers do not meet the domain policies applied and causing many problems with the network and other systems on the field.
Help, please.
concerning
Syed M. Uzair
This issue is beyond the scope of this site and must be placed on Technet or MSDN -
EQL MEM Kit - active paths reduced from 4 to 2 after the installation of SDK Dell MEM
Hello
We currently have 1 group EQL which EQL 1, PS6100XS member. The PS6100XS Member currently has 3 data warehouses. In courses run ESXi 6.0 u2 and MEM kit 1.3.0.410095 (dell-eql-mem-esx6 - 1.3.0.410095). The ESXi host has 4 network dedicated to EQL iSCSI adapters. All networks are confirmed to be installed properly with good ESXi iSCSI Port binding.
Before you install the SDK Dell MEM on the ESXi host, active paths in the vSphere EQL data store shows 4 paths. After you install the SDK Dell MEM, it correctly sets the path to DELL_PSP_ROUTED but the railways reduced to 2 for each data store:
Note: it is not a high volume of traffic again on data warehouses because it was such an environment relatively new.
Any thoughts as to why there are only 2 active channels showing and not 4?
-Saud
Hello Saud,
This behavior is quite normal. MEM and the table negotiating connections as needed. Each connection consumes memory on the table, reducing the County means that more memory is available for the cache.
Even under load, you won't probably each approach the bandwidth of two GbE NICS. The only way to get that kind of flow is completely sequential loads with big block. Then only the backup of servers and video streaming servers generate this kind of load. Hypervisors tend to be just the opposite. Since you have multiple VMs all do another IOs load becomes very random storage. If the back-end storage tends to need of IO on MB/sec rates.
With more than 2 x cards and MEM, MEM will use different cards for different volumes. For network adapters will get used, but not every NIC for each volume. If a NIC fails, it will use another NIC to replace.
Also consider what happens to storage. A PS6100 has 4 x GbE NIC. If you max 4 x network adapters on a server you would also be max on the Board with a single node.
If you have installed SANHQ you will see this clearly enough.
Kind regards
Don
-
Active connection decreases do not when the application is closed
Hello.
High number of connections active and the current number of active connection in the pool of connections to data source in weblogic 10.3 decreases do not even when I connect from my ADF (disconnect) application. I put the maximum number of connections = 15. When the current number of active connection becomes 15 app gives exception "no resources found in connection pool please increase the size of the connection pool.
can any body tell me what is this and the solution of the other before increasing the size of the connection pool?
-Usman
Hello
Make sure also that the idle connection timeout is set to lower the value.
Thank you
Sharmela
-
Connection works only not with the PlayBar activated
I am using the branching feature in Captivate 5.5. I use the reading bar control to allow users to navigate through the course. Each slide is configured with a click box to pause the slide, forcing users to click on the next button on the playback bar to scroll through the course.
The ramification of the feature cannot be used with the automatic navigation (timed navigation)? I really hope I'm missing something simple just to allow the connection to work properly. Currently, the logic of branch is completely ignored I click in the course.
I am using Captivate 5.5; Windows XP SP3; THAT IS TO SAY 8
Thank you
Jay
The ramification is on interactivity. So she requires that the user is interacting with the course somehow and that it not be a variety of responses required under what they do.
If you are using either the interactive objects (click boxes, buttons, text input boxes) that allow the user to make decisions about what direction to take, or else you have advanced conditional actions implemented which are triggered by events drag enter who choose branching based on certain criteria (for example scenarios (, who glides the user saw, or quiz question scores etc.).
If you just use the PlayBar buttons, these are going only to the break, play, rewind, move to the next or a slide backward. These don't really give you options of branches because they just move things in a linear way. You need to design interactive options that create "fork in the road" in some way.
-
Remote Desktop connection options are not available
Original title - Remote Desktop connection
Im trying to use the remote desktop connection, but when I go to test to enable it, it won't give me the three options at the base that are:
1 do not allow connections to this computer2 allow the connection of computers running any version of remote desktop3 allow that connect the computers running remote...Can someone help me please?Hi JuanLeiva
1. which edition of windows vista is installed on the computer?
2. where exactly you check for settings?3. have you successfully activated the remote desktop connection to use?
I suggest to refer to the links below and try allowing the remote desktop connection, as a result, then check if the problem is resolved.
I hope this helps.
-
Wireless connection problem - "could not contact the primary DNS server.
Hello. As of today, I had an interesting problem with my connection wireless home.
I have DSL, and my router (an Actiontec GT704-WG, for reference), periodically decides to abandon the internet connection throughout the entire family. This includes our parent unit, as well as my lap top which relies on a wireless connection.
Today, I noticed that my laptop was switched to 'Access Local.' only I went to check my modem, only to find all the lights on the side were, and the computer was working fine. I tried to reset the wireless connection, activating / disabling the wireless and switch off, Plug and reconnect to the network without wire, as well as re-booting my computer. None of these things worked.
I also received and error message that tells me it: "could not contact the primary DNS (fe80::341b:6831:1247:6707 11%).
I don't know what this means, although I checked to make sure that my ISP address connects well, and as far as I can tell it is. I also checked everything that Microsoft suggested troubleshooting guides, nothing helps.
I don't know if that makes a difference, but I noticed to my lap top more close to the router, the connection would come periodically power on and off. Also, these problems started occurring after that I installed and then uninstalled Firefox. I use Internet Explorer, but I wanted to try Firefox.
Also, my computer is an application of Toshiba Satellite L305-S5944, running Vista Home Basic, I believe.
I hope I've provided enough information.
Go to the website of the manufacturer of your router > make sure you have the latest Firmware in Vista for it.
Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > look for it last network adapters Vista drivers > download/install the.
Try without commitment TCP/IPv6:
If you still have internet connection probs, one thing to try is the separation of the TCP/IPv6 (which is done by going to network connection > right click > properties > it uncheck > OK.)
http://digitalmediaphile.WordPress.com/IPv6-how-to-unbind-from-a-NIC-in-Windows-Vista/
See you soon.
Mick Murphy - Microsoft partner
-
After import of archive site Internet 10g, resources are not in the path
Hi all
I try to import the example WCM site in GR 11, 1 newly installed material (11.1.1.7.0) using site studio backup and restore utility.
http://www.Oracle.com/technetwork/middleware/WebCenter/content/WCM-sample-site-131561.zip
Important message of the site, when I access the pages I could see that images and other resources are not rendered as paths of the images could not be resolved.
For example: the image of the logo. site is looking for the image at the following location.
/CS/groups/public/documents/wcmwebasset/oracle_logo_15h.PNG
Where as post import this image lies inside
cs\weblayout\groups\public\documents\wcmwebasset\x2xv\z29f\~edisp\oracle_logo_15h.PNG
How can we come to these problems?
To give you a bigger picture, I'm working on a CEP to migrate a site of 10g and 11g. What is the right strategy to adopt. Right now I'm doing the following.
(1) install 11 g R1 install.
(2) to use folder_g as a network interface.
(2) export 10 g Web site (I'm sure this could be split into several stages)
3) import in 11 g
(5) use the migration utility to move a folder interface folder_g to setting records.
I wasn't going to upgrade inplace, mainly because the customer wants to retain the 10g install for some time yet and didn't want to corrupt the existing installation.
I appreciate any help in this regard.
Thanks in advance,
Steven K.
Hi stephanie,.
You see the new path for the files due to the dispersion principle UCM 11 g from rule (which by default is set to the file store provider). This behavior can be changed by the following steps:
1. check what the default rule, you must Access the FileStorage field select Administration - Applets - Configuration Manager admin - modify and check what is the default setting.
It should be DispByContentId
2. remove the rule of dispersion of the weblayout / web / vault of paths of Administration - suppliers - bank file by default -
- Edit. 3. update - updated
Before you start with the above points, you must run an archive server full export target (11 g) and select the option "remove content after successful export. This will delete the server and it will be a perfectly clean instance.
Then after changes in store files, server restarts, provider import archive created and then, with the same path as seen in the instance of 10g.
Positions of reference:
https://forums.Oracle.com/message/10058823
https://blogs.Oracle.com/ecmarch/entry/working_with_the_new_fsp_dispe
https://blogs.Oracle.com/ecmarch/entry/when_is_the_default_storage
I hope this helps.
Thank you
Srinath
Maybe you are looking for
-
How to allow some windows popup in 3.6.6?
Since his arrival in version 3.6.6 I cant get Firefox for all popup windows. Adding names of sites to the list of exceptions makes no difference. Or uncheck the "block popup windows" option. This has happened Each time Firefox opened Is Upgrade 3.6.6
-
How can I get the old version of Skype back I tried a lot of things and looked at old posts on this topic, but I cant get their work and the new Skype is too crowded and constantly crashes I get 2 messages, then it crashes please help me to solve thi
-
HP Pavilion dv7-4272us: win 10 rejects my key
I bought my dv7, the original owner, recorded with HP, with win7 preinstalled. Updated win10 to flash for a clean install. Cannot activate, key invalid - why? I have no idea! error 0x803F7001 Found using key ShowKeyPlus. Cut out and glued in activati
-
Pavilion p6280t: replacement motherboard
I need to replace the motherboard (Benicia-GL8E) on my desk p6280t. I intend to buy a card Berkeley mother HP-GL8E-GS211-69001 PN: 5189-2129 replacement. 1 / is this compatible mobo with my system? 2 / I need to reinstall the o/s? (I don't have a wi
-
What are the audio problems with the Toshiba Satellite L305-S5928?
The Audio on my Toshiba Satellite L305-S5928 jump, when listening to music or movies. It often looks like tearing, or as if it gets stuck.