Wireless connection problem - "could not contact the primary DNS server.

Similar Questions

• Windows cannot contact the primary DNS server

  Troubleshooting after trying to connect HP laptop to the internet, the result was that windows cannot communicate with primary DNS server. How should I do?

  What type of Internet connection you are on, wired or wireless? If you are on a wireless connection, try switching to a wired connection and try the download.

  Click Start, type: cmd

  Right-click on cmd, and then click Run as administrator

  At the command prompt, type the following:

  ipconfig/release

  then

  ipconfig/renew

  then

  ipconfig/flushdns

  leave the command prompt

  Click Start, type: folder

  Press enter

  Delete the contents of the temp folder

  Restart the computer and try to download again.

  If the problem persists, try resetting your router if you are connected to one.

  Turn off the router, unplug it, wait 10 minutes

  Plug it in again, power up once again

  Reconnect the Ethernet cable

• How can I stop the yellow browser bar to appear? one that says "could not contact the server connection?

  This yellow bar appears constantly while I'm using the internet. It is said"LastPass could not contact the server connection, etc. etc. »

  It is very annoying and causes my screen to jump on when it is active.

  I use windows 7 on a HP desktop computer.

  Or disable LastPass until you contact LastPass support for help.

• RH10: Test connection displays error: could not contact the site at the specified url.

  Hello

  I am using sharepoint as a control source code for my project. Here are the steps mentioned in the link of reference robohelp 10.

  • Configure RoboHelp for SharePoint settings
  • Configure the SharePoint document library settings
  • Add a project to a SharePoint document library

  Step 1 & 2 are completed successfully. But in step 3, when I add version control, an error message appears.

  File-> Version Control-> add to version control-> connector Sharepoint RoboHelp-> Ok-> enter Sharepoint site-> test the connection

  Error message: "test connection displays error: could not contact the site at the specified url.» There is no web named *. "/ _vti_bin/sites.asmx.

  Help, please.

  Hello

  Using SharePoint 2010? Earlier versions are not supported for version control.

  What is the URL that you use? You must point RH on the site or subsite holding library. Not the library itself.

  Take a bow

  Willam

• Windows 7 "the network connections folder could not retrieve the list of the network adapters on your Machine. Please make sure that the network connections service is enabled and running. »

  Get the message "the network connections folder could not retrieve the list of the network adapters on your Machine. Please make sure that the network connections service is enabled and running. "I am NOT able to connect to the internet please help. I use Windows 7 OS

  Hi Odile,

  Thanks for posting your question in the Microsoft Community forum.

  It seems that you have a problem with the connection to the Internet and receive the error message "the network connections folder could not retrieve the list of the network adapters on your Machine. Please make sure that the network connections service is active and running".

  
  I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.
  I may need a few more details to better understand the issue.
  1. did you of recent changes on the computer before this problem?
  2 do you have wireless or wired Internet connection?
  Method 1:
  We'll first run check network troubleshooting if this can help.
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7
  Method 2:
  If the problem persists, I suggest you try the procedure described in the article and see if it helps.
  Wireless and wired network problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1
  Method 3:
  If the problem persists, I suggest you try the procedure described in the article and see if it helps.
  How can I troubleshoot network card?
  http://Windows.Microsoft.com/en-us/Windows7/how-do-I-fix-network-adapter-problems
  For more information, please see the link.
  Why can't I connect to the Internet?
  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet
  Get back to us and let us know the State of the question, I'll be happy to help you. We, at tender Microsoft to excellence.

• Could not contact the Flickr web service

  In recent weeks, I am unable to upload pictures directly from LR on Flickr.

  The message I get:

  "Cannot update this collection.

  Could not contact the Flickr web service. Please check your Internet connection. »

  
  

  LR version 2015.1.1

  Generation 1032027

  
  

  Flickr Pro account.

  
  

  Any advice? I'm happy test the beta fix only if available.

  
  

  I used to use the plugin to Jeffrey, and it's (I think still is) a fantastic product. Again, having a built-in feature delivered with LR has won my heart.

  BTW: it seems that the issue is on the side of Flickr and relates to their limitation (IP based) network. I don't understand why they do it and why too drastic. Try again potentially additional native plugin LR Flickr could help.

  It was enough for me to activate VPN to route traffic through a server in San Francisco and it's all very well now. My original traffic was from London.

  Boring, but has less there is a workaround.

• vCenter Single Sign we install fails (could not contact the search service)

  I try to install the first server vCenter our Organization and he keeps fails with the error "could not contact the Search Service.  Please check VM_ssoreg.log in the temporary folder of the system for more information".  I checked the system temporary folder and there is no file that is created, but there was one called vminst.log.  In the file, I found the following, but I can't find a way to solve the problem:

  VMware VirtualCenter-build-1123961: 07/08/13 08:40:03 see vm_ssoreg.log in the temporary folder of the system

  VMware VirtualCenter-build-1123961: 07/08/13 08:40:03 SSO registration tool failed with return code 2

  VMware VirtualCenter-build-1123961: 07/08/13 08:40:03 get the property UILevel = 5

  VMware VirtualCenter-build-1123961: 07/08/13 08:40:03 updated property ProductName = VMware vCenter Server

  I try to install the server 2008R2 64-BIT STD and have done the following to try debugging the problem:

  1 server is part of Active Directory, and the FULL domain name can be resolved successfully by using nslookup.

  2 time server is correct.

  3. manually added the name of the computer in the host file

  4. I tried installation 5.1 update 1 b

  Any help would be greatly appreciated.

  Yes, it could be the problem. the non-ASCII characters, semicolon (;), double quote (' '), single quote ('), circumflex (^) and backslash (\). is not supported by the SSO passwords.

• Can't set Messages again for me iPad 4.  A change of email address it took me to change my apple ID and password.  I tried 3 days pretty regularly to set up messages and I thought who could not contact the server iMessage.

  I tried to put in place the Messages in my, new to me, iPad 4.  A new email required adaptations of apple id and password.  For three days, fairly regularly, I have tried this and the message that could not contact the server iMessage.

  My new ID Apple seems to be OK.  My e-mail and password are accepted at every attempt.  I'm stuck.  Help please or suggestions.  Thank you very much.

  What is an iPad only WiFi or cellular capacity?

  If WiFi only - you are on the same network as the corresponding phone, on which you have enabled iMessage?

• Problem with the primary dns server, get the error "There could be a problem with one or more network adapters on this computer."

  Hello

  I was all of a sudden having problems connecting to my wifi at home. When I was diagnosed, he says cannot communicate with primary dns server. I tried all methods in similar positions, but nothing works. I am also unable to connect to internet with my iphone and the itouch. It's really frustrating, because I've already tried all of your suggestions. I just ran another ' diagnose connection problems and it says the following:
  "There could be a problem with one or more network adapters on this computer." Help, please!
  Thank you!

  Thanks for your help, but I have tried this before. In the end I just unplugged my modem and plugged in again and it worked? I feel a bit silly not to try first.

• Satellite L500D - Iinitially had a problem "could not load the profile.

  Satellite L500D initially had a problem 'could not load profile' then stop. It is now the windows installation discs that I don't have. Where can I get them? They can be downloaded from Microsoft or Toshiba sites?

  Error message:
  File: \boot\BCD
  Status: OxcOOOOOOf
  Info: an error occurred while trying to enter the boot configuration data

  ANY HELP WILL BE GREATLY APPRECIATED THANKS

  Hey Buddy,

  > They can be downloaded from Microsoft or Toshiba sites?
  No, the disc can t be downloaded because it s not for free.

  You can start in safe mode?

  In the worst case operating system is confusing to the top and you have to reinstall Windows, but so you can take the Toshiba Recovery disk that will restore your notebook back to factory with all the drivers and tools of Toshiba.

• Windows Experience Index problem: could not measure the performance of video playback

  My pc is not yet rated. When I click on rate appears on this computer, a msg error saying that Windows Experience Index for your system could not be calculated, could not measure the PERFORMANCE of VIDEO PLAYBACK. What should I do. Help, please

  Hello

  Here are a few things to check before launching performance index Windows (WEI).

  • Quit all running programs, and restart the computer before running the assessment (WEI).
  • Check with the manufacturer of the computer or the motherboard manufacturer for BIOS updates.
  • Make sure you have the latest Windows 7 compatible drivers for the graphics device installed (video card).
  • If you have any third-party media players installed, uninstall them until the end of the evaluation of the WEI.
  • If you have installed any third-party Media Codecs, try to uninstall them until the end of the evaluation of the WEI.

  Open Windows Explorer and navigate to the folder C:\WINDOWS\Performance\WinSAT .

  You should see the following 8 videos.

  2 files with .mp4 extension.

  3 files with the .mpg file extension.

  3 files with .wmv file extension.

  Double-click each of these files. They should open and play in Windows Media Player. These are the files that WEI runs video performance.

  One thing to remember is that the WEI score is only an indicator of the ability of the main components of hardware on the computer. It has no effect on the performance of the system.

  Tell us what you find.

  Concerning

• OfficeJet Pro 8600 Plus: loss of wireless connection, printer does not accept the password wireless

  My printer has suddenly lost its wifi connection. It's the only phone connected to my network to do so.

  Through the Wireless Setup Wizard to restore the connection. Assistant tells me that I entered an invalid password wireless, that is not true. (I confirmed that all devices connected to the network using the same password).

  Reset the router (Technicolor of Time Warner). Reset the printer. The 'Restore default network' done. No luck.

  Zero has changed since yesterday, when my printer was working fine. I used the same router for months, do not change any settings. Any thoughts on what may be the issue? A bad update happen?

  Thanks in advance.

  My apologies for the late reply. I managed to get this problem resolved by phone to customer service.

  The security mode of the router had to be changed to 64 WEP for wireless connection to be restored. According to Support HP, it's a common problem with the routers in Technicolor. There was no explanation as to why the printer has suddenly lost the ability to connect wirelessly when safety was created to WPA2-PSK. The network has been configured this way for more than a year.

  I have almost solved this problem on mine (I had read about changing of security in a different post), but ran into a hiccup because of Safari. For some reason, Safari prohibited access to a menu page for my router security settings. You can imagine how boring it is to look at the HP Support use Firefox to access the router and do what a mouse click more, and then I had to make the change. So, if you make this change, be sure not to use Safari to access the gateway of the router Technicolor. Use Chrome or Firefox.

• Cannot contact the primary DNS 64.13.4.5

  Operating System: Windows Vista Version: Internet Explorer 8

  

  Just today I started having intermittent problems with my internet connection while playing an online video game.  Then he stopped just working altogether.  He cannot communicate with the DNS server.

  I called my ISP and determined that it was my machine.  I plugged in my laptop (windows xp) and it works fine.

  Here is the ipconfig/all command to the broken machine

  C:\>ipconfig/all

  Windows IP configuration

  Name of the host...: *-PC
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
  ... Description: Marvell Yukon 88E8056 PCI-E Gigabit Ether
  Net controller
  Physical address.... : 00-19-21-54-54-A9
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  IPv4 address...: 64.13.4.226 (Preferred)
  ... Subnet mask: 255.255.254.0.
  Lease obtained...: Friday, October 29, 2010 21:00:20
  End of the lease...: Saturday, October 30, 2010 21:00:20
  ... Default gateway. : 64.13.4.1.
  DHCP server...: 64.13.4.6.
  DNS servers...: 64.13.4.5.
  64.13.115.12
  NetBIOS over TCP/IP...: enabled

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {59491320 FDB5-405-AD8F-A5AA7722D
  0 C 3}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 9:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  The connection-specific DNS suffix. :
  ... Description: Card 6TO4
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2002:400d:4e2:400d:4e2 (Preferred)
  ... Default gateway. :
  DNS servers...: 64.13.4.5.
  64.13.115.12
  NetBIOS over TCP/IP...: disabled

  C:\ >

  ... And here is the ipconfig/all command for my laptop that works fine.

  C:\>ipconfig/all

  Windows IP configuration

  Host Name . . . . . . . . . . . . : ****
  Primary Dns suffix...:
  Node... type: broadcast
  Active... IP routing: No.
  Active... proxy WINS: No.

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
  Description...: Realtek RTL8139/810 x Family Fast Eth
  ernet NIC
  Physical address.... : 00-16-36-07-D6-C9
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  ... The IP address: 75.93.168.202
  ... Subnet mask: 255.255.240.0.
  ... Default gateway. : 75.93.160.1.
  DHCP server...: 64.13.4.6.
  DNS servers...: 64.13.4.5.
  64.13.115.12
  Lease obtained...: Tuesday, September 28, 2010 02:09:10
  PM
  End of the lease...: Wednesday, 29 September 2010 09: 2.1
  0 H

  Ethernet wireless network connection card:

  State of the media...: Media disconnected
  ... Description: Broadcom 802. 11b / g WLAN
  Physical address.... : 00-14-A5-60-BD-35

  C:\ >

  I tried a technical support at the ISP, they concluded that the problem is with my computer...

  I tried

  system restore

  NETWORK card driver update

  disable TCP Window Scaling

  ipconfig/flushdns

  ipconfig/registerdns

  ipconfig/release

  ipconfig / renew

  netsh winsock reset catalog

  netsh int ipv4 reset reset.log

  netsh int ipv6 reset reset.log

  I can't ping any Web site, including DNS or gateway, or live.com, using the IP address or other.

  I can ping 127.0.0.1

  I also tried to adjust my computers IP to non-working parameters exactly as it is on my laptop, nothing works

  nothing seems to work:(serait-ce une sorte de défaillance matérielle?) Device Manager indicates that the NETWORK adapter does not work correctly

  I bought a new NETWORK card, and it works with the new NIC. weird

• Could not contact the server hotfix, check your connection

  There is nothing wrong with my connection. I am runnimg version 6.4.22722 and would like to update.

  Someone at - it ideas/suggestions

  2nd edition,

  It used to be free for 100 devices

  then it was free for 200 devices

  now its free for the 200 interfaces, for only 30 days?

  can someone clarify the situation

  Hi Todd,

  Your question relates to Foglight NMS, so your best option is to post in the Discussion NMS Foglight group.

  A search on the forum of NMS Foglight reveals a few posts with similar symptoms:

  Free Quest network tools will not activate

  Can not activate Quest free network tools

  It seems that the problem will be resolved by upgrading to the latest version (6,7).

  The SMN experts who monitor the Foglight NMS community should be able to clarify your question about the free version.

  Kind regards

  Brian Wheeldon

• Web interface error - could not contact the server at this time

  Hey all,.

  Immediately after completing the deployment of the new 2.1 UM I'm running an obstacle when connecting to the web interface. After authentication, with the web interface, I get the following when you select my user type (service provider or aggregator - anyone):

  

  I redeployed the VAPP twice is not a transient deployment problem. Networking seems fine - I can ping from areas on the Internet from the SUSE console. Not sure that this message refers on the 'server' is in contact with. It is deployed on ESXi 4.1 in a cluster vCentre vswitches standard, nothing special.

  Any ideas?

  Kind regards

  Daniel Whittaker.

  Daniel,

  When you get the message after installation, click OK and then refresh the page or click F5.  The message should appear is no longer.

  Kind regards

  David