Tecra M4: Utility of AutoRotation should not turn external display

Similar Questions

• Tecra M9 - sometimes that it will not turn on

  Hello.

  I have a Toshiba Tecra M9 who has a problem. Sometimes it will not turn on. You must remove the battery and press the power button. When it loads will work fine until I have move or take it upward and then hangs and crashes. Then, you must take the battery out so he can turn it back on if it will be in all.

  I tried to reload xp, tried without battery, tried a known good ram in both slots, a different hd and took part to see if I can see something loose, I have now run out of ideas.

  any help would be good

  Thank you

  Hello

  Which is really strange, buddy... In my opinion, that sounds like a hardware problem, what do you think?
  You should contact a technician for laptop (authorized service provider). Guys can verify and Exchange defective equipment parts. Maybe a mailfunction of the motherboard or the CPU

  By the way: you have updated your BIOS? If this is not the case, to do this, first!

• Satellite A10: RGB Port is not installed - can not use external display

  Satellite A10 the RGB PORT is not installed & cannot be used as external display. I tried to install the communication or COM 1. interrupt code. What are the possible solutions?

  Hello

  What did you mean by "not installed"?
  Generally, you don't need to install anything. You don't need any drivers for this port 3.
  Windows XP drivers should work properly.

  Please check device manager if there are errors or yellow exclamation points.
  If the problem occurs for a short time, you can try to use the WinXP restore tool.
  This tool will reduce the BONE until the start.

• You can turn external display (after the last "update")

  I just installed last updated and I can not turn my external display! There is no option in the settings.
  Moreover, I'm afraid to install any new update because it always brings new troubles - where do you go Apple?

  In help, I found something like "If the drop down menu to display rotation is not available, then the computer did not support this function...". "What? I have set it to level or Downgrade?

• Broken LCD - can not get external display

  My screen is no longer good so im trying to connect an external display.

  Been trying for hours to try to get the external display to work to boot.

  Ive tried 2 sets of hd and svga cables change everything. The function key.

  The laptop does not recognize the display, but seems to go in something or powersave mode.

  The only way I can get the external display to work is if I remove the battery and wait a bit and then power

  the display works with a notice on the screen that the cmos will reset to default settings then restarts

  and back to where I was once again... IM thinking that it something in the bios that is the cause.

  I thank you and hope I can understand this.

  Pavilion dm4-1160us

  HI Ezfilez,

  I understand that you have a problem with the external screen on your Windows 7 computer.

  Sometimes it is in the BIOS. If you follow the link and update, that it should help solve your problem.

  http://support.HP.com/us-en/document/bph07110

  Please let me know if you need assistance.

  Thank you

• Tecra S11 - utility of fingerprints can not connect to the AES1660 probe

  Hello

  I'm a new user Tecra S11 (PTSE3E), but the former user of Toshiba.
  After two hours I was using the new laptop, fingerprint software no longer works.
  I tried to update the firmware of the sensor AES1660 (now is the version 9.0.8.21) but nothing!

  The OS is Windows 7 Pro, the BIOS version is 2.60, material management said that the sensor is connected and works well.
  When I run the utility of fingerprints, the "cannot connect to the sensor" message.

  Ever happened to someone?
  Little help? I already contacted support today!

  Thank you.

  Great man!
  Thanks for the comments!
  Very nice work!

• Tecra Z50 - utility of fingerprints can not connect on the sensor

  Although the latest version of the driver for validity sensor is installed the fingerprint utility cannot connect to the sensor.

  System: Win 8.1 64-bit

  You should put a little more information on your machine.
  Are you using the version Win8.1 as recovery image original Toshiba?
  I guess that if you use the laptop with the factory settings, everything should be OK.
  Have you noticed this problem with the original driver?

• Windows 7 starter edition: sceensaver not committed and does not turn off display

  I have Windows 7 starter on my Acer Aspire One.  The display has stopped turn off automatically (as it is supposed, by the power settings) when the computer has been sitting idle for some time.  I checked the power settings several times, as well as turned on the screen saver (but it won't commit).  I checked the display drivers & they are up to date.  I have not all connected devices that might wake the computer.  I have not installed new software recently and have any kind of function "awakening."   l normally play music by the bias of Windows Media Player or stream music online (Pandora and live365) when I fall asleep and so don't want to close the lid, but want the computer turns off the screen so that it would light up the room all night.  Please let know us what could go wrong.  Thank you!

  Hello

  Method 1: Run the troubleshooter of power

  You can run the troubleshooter of power to set your computer's power settings. The resolution of the problems of power check things as settings timeout of your computer, which determines how long the computer waits before turning off the display or enter the mode 'sleep'.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-power-Troubleshooter

  Method 2:

   

  Follow the post proposed by Serge D.

   

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-desktop/screen-saver-display-power-off-Don ' t-work-when/498b768d-c786-4741-81d4-28d6d189a88f

   

  Hope the above information is helpful.

   

• What should I do when Windows Update is blocked for 3 days, saying "do not turn off your computer.

  Windows Vista Home, automatic installation of updates 3 days ago, when it froze. He said 'do not turn off your computer', but ctrl + alt + delete does not work, so what do I do? I can't use all the controls while the update is frozen. If it's a difference, it is stuck on that updated 3/3 to 66%. Thanks in advance.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_update/computer-freeze-during-Windows-7-update/8968dba7-1e08-4594-bd49-3559d49c6cfe

  08/13 / 1115:29: 13:00 HTC

• Satellite L500 - can not turn on the new wireless network card

  I have little problem with client model T. Satellite l500-1ek. I change orginal at BCM94321MC wifi wifi card mini pci card (rev 6). Card works well - everything is ok - driver installed ok.
  But I can not turn on wifi with FN + f8 key - Windows.

  This isn't a software issue - this button should work before starting any kind of system, but do not work. I tried everything, including the update of the BIOS. Card works correctly, but can not turn on wifi: (.)
  Can anyone provide another solution than to change the map?

  PS.
  I have reinstaled value-added package and Flash utility support card - fn Panel works but buton f8 disappeared.
  PSP.
  I tested with another card from mnipcie and have same problem - can not turn on wifi - fn + f8 does not work

  Post edited by: Ipcur

  Hi Ipcur,

  Why you traded with another wireless network card model?

  He works with the wireless network card preinstalled Toshiba?

• K010 ENVY: my laptop will not turn off

  Hello

  When I shutdown/hibernate/standby/resume my laptop, it will die completely.

  All programs will be closed (when stop or restart) and I think that OS will also close. But the laptop will not turn off. Power LIGHT and fan will stay on.

  And when I try to Hibernate, everything is ok, but I have the same problem.

  Whenever I have to turn it off by holding the power button, otherwise the battery will be discharged.

  After manual turn off, when I turn it on again, everything works correctly:

  -If hibernation: OS will continue to last situation.

  -If start/stop: OS works normally without error or warning.

  After sleep, OS works from the beginning. Because the data stored in RAM and will be deleted after power off.

  Perhaps a portable automatic perevent equipment turned off. All the drivers are up to date.

  Is there a parameter/software to check and fix my problem?

  Thank you

  Hello

  You are welcome

  On some machines, the pilot for 11 series IMEI has been known to cause that kind of question of the judgment, so it may be worth trying an earlier version.

  You can use the following method to install an earlier version of the driver IMEI.

  Download driver IMEI on the link below and save it in your downloads folder.

  http://ftp.HP.com/pub/SoftPaq/sp66001-66500/sp66228.exe

  Disable your wireless card (should be f12 ).

  Open your download folder and run the installer - it warns you that it is an earlier version, but simply continue.

  When finished, restart the laptop.

  If the computer shuts down correctly, turn on your wireless adapter and use the utility on the following link to prevent Windows 10 to update automatically the driver IMEI again.

  https://support.Microsoft.com/en-GB/KB/3073930

  Kind regards

  DP - K

• HP Pavilion 15 p150nh: laptop does not turn off completely

  Hello!

  I have a laptop HP Pavilion p150nh 15. It does not turn off. If I want to close it will turn off completely. I have black screen but the vens are still on and the buttons start led is also single beds. I've tried everything. Updates, hard reset I was looking for BIOS but nothing.
  Help me please!

  Hello

  On some machines, the pilot for 11 series IMEI has been known to cause that kind of question of the judgment, so it may be worth trying an earlier version.

  You can use the following method to install an earlier version of the driver IMEI.

  Download driver IMEI on the link below and save it in your downloads folder.

  http://ftp.HP.com/pub/SoftPaq/sp66001-66500/sp66228.exe

  Disable your wireless card (should be f12 ).

  Open your download folder and run the installer - it warns you that it is an earlier version, but simply continue.

  When finished, restart the laptop.

  If the computer shuts down correctly, turn on your wireless adapter and use the utility on the following link to prevent Windows 10 to update automatically the driver IMEI again.

  https://support.Microsoft.com/en-GB/KB/3073930

  Kind regards

  DP - K

• Windows Updates Setup error: "configuration of the Windows updates failed. Restoration of the changes. Do not turn off your computer"stuck at 12%

  Just returned to windows 8, got my Norton security is and it.then update was of updates, so I can update to windows 8.1, but I got stuck when you try to update windows 8. It happened at 12%, and then tried to restart, it's 12% again.then what it says that windows does not not update reconfiguration do not turn off your computer.but I read someone post where they keyed off long the computer out the wireless USB mouse and took the card Sd, and the battery, put the battery back , but left the Sd Card and the mouse.and wireless USB, said, he started working.i tried all the this.and isn't yet working.it has been trying to run my computer hot.so I waited until what she calmed and it came again the same thing. ? Stuck in this mode.what do I do? I don't know if I should try just reset the computer of hole again or that it would be wrong.

  Original title: tried to update computers rose to 12%

  Hi Sandra,.

  Thanks for posting your query in Microsoft Community.

  You did it any significant hardware or change software on the computer before this problem?

  I understand that you can not install some updates with the error message "failure of configuration of the Windows updates...". ». I can imagine the disadvantages suffered by you and will certainly help you in the right direction to solve the problem.

  First place, according to the error message, I suggest you to try the steps in the following article and check if it helps.

  "Configuration of the Windows updates failed. Restoration of the changes. Do not turn off your computer"error when you try to install Windows updates

  Note: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  
  

  The question may arise if the Windows downloaded update packages are corrupt. So, if you are able to boot to the desktop with the help of the above article, I also suggest you try the following steps and check if the problem persists.

  Method 1:

  Try to run that Windows update utility provided in the following link.

  Problems with installing updates

  Try to install the updates after running the troubleshooter.

  If the problem persists, try the following method.

  Method 2:

  I suggest you to use Deployment Image Servicing and Management to fix Windows Update errors.

  (a) open an elevated command prompt. To do this, press the Windows key + Q and type in CMD right click on command prompt in the list and select run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click allow.

  (b) type the following commands. Press enter after each command

  • DISM.exe / Online/Cleanup-image /Scanhealth
  • DISM.exe / Online/Cleanup-image /Restorehealth

  (c) close the command prompt, and then run Windows Update again.

  Check if the problem persists.

  Hope this information is useful. Let us know if you need more help, we will be happy to help you.

• iPad IOS 10 - AutoCorrect keyboard does not turn off?

  I don't know if it is a problem of IOS 10 or if it is a question of the iPad. One of the first things I do when I get a new device is turn off easily. I hate to correct automatically, but it seems not turning off itself. I was typing a message to a friend of mine and to instead keep the word I typed (Pervy) it replaces (Percy).

  I just upgraded to IOS 10 and checked to see if the AutoCorrect has been disabled or if she has it on again. Even with typing this message, it keeps replacing words on me with words that I don't type and are not what they should be. It is not a question of spelling either, so I don't know what to do to fix, but it's very annoying.

  Hello. You may also need to disable predictive. If you are using a physical keyboard, there are different settings for it. They appear only when it is connected.

• MacBook will not turned off properly

  Hello

  my MacBook Pro 13 "2013 retina is not turned off properly after installing macOS Sierra.

  It takes about 20 minutes after clicking n closed. The screen is black and miss me closed animation (this circle loading bit). After a long time the circle appear and it takes 10-20 seconds (normal closing time) to shut down my computer.

  To me it seems that there is a program or task that can not shut down properly.

  How to see what program slowed down the process of closing?

  Thank you very much for your help!

  You can try a SafeBoot to clear the cache of the SafeBoot https://support.apple.com/kb/PH18760?locale=en_US files

  Try resetting the SMC http://support.apple.com/kb/ht3964

  Try resetting the NVRAM/PRAM http://support.apple.com/kb/ht1379 memory

  The recovery utility (R command at startup) try disc > first aid on your Macintosh hard drive

  You can always try reinstalling macOS 10.12 on top of your existing macOS 10.12

  Always good to have a current backup plan: make a clone of your boot disk bootable