Tecra R840 stop energy eco-mode

Similar Questions

• Tecra R840 - Win8 - energy hibernation mode

  Hello

  I did the upgrade offered to W8, I am very satisfied with the W8 system, but the problem is that the laptop consumes battery also in hibernation mode.

  I wouldn't understand that energy consumption will be in mode 'sleep', but on the hibernation mode?

  I discovered that when the computer is in sleep or Hibernate, and I opened the lid, the computer automatically starts EVEN if the 'power computer when open cover' option is unchecked.

  When I select to shut down the computer - it does not react to open the lid, I have to press the power button.

  The problem may come from the windows system, that BONE tolds the computer wake up once the lid closed.

  The problem is, the computer starts to load whenever I wake up after hibernation (I had my 15 minutes of the Home Office, and it consumes about 1 to 2% of battery.

  It is quite annoying that my battery capacity full load is about 83% of the original (I bought my PC in June2012).

  I got Lenovo T60 7 years ago, and there was an option to start to charge the battery only when the battery charge was less than 95% and it saves the battery capacity.

  Does anyone has some clues?

  Thank you!

  Fact is that the battery capacity will decrease even if the laptop is turned OFF completely. Capacity of the battery will lose some percent of capacity. To reduce this review - http://aps2.toshiba-tro.de/kb0/FAQ9C015N0001R01.htm
  A useful document for you can also be http://aps2.toshiba-tro.de/kb0/HTD9401AZ0001R01.htm

  > I Lenovo T60 7 years ago, and there was an option to start to charge the battery only when the battery charge was less than 95% and it saves the battery capacity.
  As far as I know that this option is not available on Toshiba laptops. When it is connected to AC notebook power supply starts to load the battery automatically.
  There is no possibility to change anything.

• Tecra R840 - energy SSD after closing

  Hello

  Could someone tell me what than a ssd power consumption when the computer is turned off?

  I have a laptop Toshiba Tecra R840-16J (bougth 6 months ago) with a sweet Plextor M5Pro 512 GB ssd intalled. Yestarday, after a charge of 100%, I liquidated the laptop and today (after 4 pm) I turn it on! The battery was at 93%. Is this normal? What could be the cause of this decline of 7%?
  I use a bluetooth mouse but I thing that when I stop the laptop everything must be switched off!

  Kind regards
  Paulo

  Hello

  Some options such as wake on LAN or wake on keyboard drain on the battery even if the laptop is turned OFF.
  To avoid this, you need to turn off these options in the BIOS.

  Note: Don't forget save changes when settings have been changed.

• My screen saver does not work all the time, usually this seems to happen once the aircraft stopped in the energy saving mode.

  Original title: my screensaver does not work all the time

  My screen saver does not work all the time.  First time I have turn on computer, it works OK.  Later in the day, this isn't.  Usually, this seems to happen once the aircraft stopped in the energy saving mode.  After the reactivation of the computer (do not), the screen saver does not work when it should. How to run all the time?  I am running Kapersky Internet Security 2011.  This would be closed by the screen saver?
  Thanks, Garybuyit

  Hi garybuyit,

  Thanks for posting your question in the Microsoft answers Forums.

  Just so I'm clear, updated you the graphics cards in Device Manager? You have access to a Windows XP installation disc. If so, follow the steps in this document to make a scan of the SFC. This analysis will attempt to repair or replace any missing or corrupted system files.

• TECRA R840-16V to win7 64-bit to win10 level

  I tried to upgrade my Tecra R840-16V (number PT429E-05M00KGE) form windows 7 64 bit pro to windows 10 pro through windows update. During the upgrade procedure is complete all seemed ok, but after a while, the system froze (even the mouse). I did a reboot in my system via the power button / stop, the system has worked well for about an hour and froze again. I did a reboot via the Start button / stop, one more time and I had the same problem after all. I did a restore of the system in windows 7 and everything works fine without any gel at all.
  Is this a known issue? Is there a solution or suggestion to update my system without problems on windows 10 pro?

  Thank you

  Posted by axiotidis
  

  I tried to upgrade my Tecra R840-16V (number PT429E-05M00KGE) form windows 7 64 bit pro to windows 10 pro through windows update. During the upgrade procedure is complete all seemed ok, but after a while, the system froze (even the mouse). I did a reboot in my system via the power button / stop, the system has worked well for about an hour and froze again. I did a reboot via the Start button / stop, one more time and I had the same problem after all. I did a restore of the system in windows 7 and everything works fine without any gel at all.
  Is this a known issue? Is there a solution or suggestion to update my system without problems on windows 10 pro?

  Thank you

  Hello

  Never solved this problem, I have the same problem with my Tecra R840. I have windows 10 initial installation when it was first released, however had the freezing issue (System fan would also begin running at 100%, that is very strong but whole machine was locked and would require a hard reset). After a few weeks of this question, that I started Windows 7 and which would be fine.

  However, just tonight I thought I would try the anniversary 10 Windows Update to see if that had solved the problem, unfortunately the same problem persists. After you have installed update Windows 10 anniversary (updated to Windows 7), the laptop freezes still. There a simple 3 minutes after connecting the fan turns 100%, and everything froze upwards.

  Thoughts/ideas or help here would be appreciated?

  See you soon

• Tecra R840-16J - Win 7 installation - how?

  Hello

  I want to make a new one. Clean instal win7 Pro in my Tecra R840-16J (a BSOD appeared only 6 months after I bought it!). I'll install an SSD too!

  Could someone tell me how to do? (I mean, which drives should I have to install hel?) I downloaded al 48 discs and Aps for my model when using win7 64 bit.

  Kind regards
  Paulo

  Hello

  Install the drivers in the following order:

  Windows 7 64 bit

  Driver USB-Serial V1.3.0
  PlayReady PC Runtime 1.3
  Infineon TPM professional package 3.60.2071.00
  SW 9.2.0.1015 Chipset installation utility
  Intel Management Engine Interface 7.00.02.1164
  Intel AMT 7.00.02.1164 software
  8.801.2.1 - 101225 a-111146C-Toshiba AMD display driver
  Intelligent management of the TOSHIBA v1.0.2.0M screen
  Driver Intel Rapid Storage Technology 10.1.0.1008
  Realtek Audio Driver 6.0.1.6271
  Intel LAN driver 15,7
  USB3.0 Driver 2.0.32.0rior
  ALPS Pointing Device Driver v7.x6.303.106_A
  Synaptics Touch Pad Driver 15.2.4.4
  Driver O2Micro 1.1.4.207G smart card reader
  TOSHIBA value added package 1.4.1
  Ricoh 2.11.17.02 card reader
  Intel Wireless LAN Driver 14.0.0.113.0.s64
  Intel Proset 14.0.1.0.0.s64 & 13. 3.0.0.1.s64
  ConfigFree 8.0.35
  TOSHIBA Network Device ID registry setting tool 3.0.32.4 - 13
  TOSHIBA Fingerprint Utility V1.0.2.36
  TOSHIBA Web Camera Application V1.1.2.13
  3.1.3 TOSHIBA face recognition
  Utility of rotating 180 degrees TOSHIBA v1.4.0.0
  TOSHIBA eco Utility 1.2.21.64
  TOSHIBA HDD/SSD Alert 3.1.64.6
  TOSHIBA HDD Protection 2.2.0.12
  TOSHIBA Service Station 2.1.45
  TOSHIBA PC Health Monitor 1.7.3.64
  TOSHIBA Sleep utility 1.4.1.7F
  TOSHIBA V4.00.4.12 VCR - HAS
  Intel Wireless Display 2.0.27
  TOSHIBA v2.0.4 synchronization utility
  TOSHIBA Media Controller 1.0.85.4
  TOSHIBA Media Controller plugin 1.0.5.13
  PatchFiles

• Tecra R840-10 t has no work webcam or USB 3.0 port

  Even if this [another thread | http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=62061&start=15&tstart=0] has been marked as resolved, the problems remain, but are not related to the bone, hw-partners.

  1 week after that I got a Tecra R840-10 t (PT429E-00M007EP) of Windows 7 have frozen at startup and the fan run at maximum speed. All I could do was to enter safe mode. After a factory reset (reinstalling OS of the hidden HD partition), not even the safe mode worked!
  Took back to the store, 2 days later a local Toshiba representative referred to the store as fixed (they have updated the BIOS...)

  2-3 weeks later, same problem. I called Toshiba directly, they have picked up the laptop, took almost 2 weeks and sending parts of the Germany twice before they sent it. I had to call them to find out they were going to deliver the next day. So far it seems to be fixed, Windows has not frozen since.

  However, now, little more than a month after I bought this laptop from professional quality, I noticed that, on his return, the USB 3.0 port (as long as this port) and the webcam does not work. They do not appear in the Device Manager, update their drivers through page for the download of Tecra yields nothing (and you have to go through hoops to actually install the webcam driver), nothing. It's as if they did not exist. I guess that any material they brought in wasn't exactly in perfect condition, or someone forgot to plug it into some pine trees.

  I tried several Linux LiveCD as well, they all recognize the material to varying degrees (being the most comprehensive Debian), but no recognize the USB 3.0 port or the webcam as well.

  Not an OS problem. Call them once again, waiting for a response from a representative Monday morning. Seriously considering to move directly to a repair center and asking the complaints book. There is no guarantee that this laptop won't break again.

  Not a happy camper.

  Hello

  > I tried several Linux LiveCD as well, they all recognize the material to varying degrees (being the most comprehensive Debian), but no recognize the USB 3.0 port or the webcam as well.

  Have you tested this with Toshiba configured OS?
  It would be interesting if Windows 7 would get the same problems, recognizing the USB 3.0 and the webcam

  by the way: this is a user forum to...

• Qosmio X 875 - ECO mode does not work immediately after Win 8 upgrade

  I used the upgrade Toshiba Upgrade Wizard to Win 8. He succeeded well uninstall the incompatible software before the upgrade and install the new Toshiba and driver versions after the upgrade.

  I activated the ECO mode, and to my surprise, it does not work as before (in Windows 7):

  * Now, it works with the brightness to level 1 *... very dark. Before, ECO mode allowed me to go up to level 4 and was always considered in Eco mode...

  If I increase the brightness, the 'eco mode is disabled' message opens immediately.

  How to contact Toshiba to inform them of this problem and the other problem I found with the new BIOS?

  BTW, I am owner of a Qosmio X 875

  Post edited by: qosmitto

  > How to contact Toshiba to inform them of this problem and the other problem I found with the new BIOS?
  Contact your Toshiba authorized service provider in your country.

  Read this:
  + What is the TOSHIBA eco Utility? +
  http://APS2.toshiba-tro.de/KB0/FAQ2503AT0000R01.htm

  > It changes the brightness of the display of level 4, changes the brightness of the grey screen of level 1 (* 4),.
  _The * 4 means only on models with Windows7 installed _

  I guess that the previous configuration was only Win 7.

  8 win was made for mobile (use of the Tablet), the energy consumption of battery is also very important plant help to win 8. The consumption of the battery must be taken at the lowest level possible.
  So I guess that now help win 8 ECO medium mode and save the power max and long battery life time working at a max level.

• Satellite A500 - software jump issue and eco mode key does not work

  Hi all you guys :)
  I read many forums these days, and my problem is still there.

  I did an update provided with records of 2 updates for Toshiba (Windows 7 on a disk and drivers updated to this OS in the other disk) and the first 2 weeks, everything was ok. Then stopped working the windows media player jump list. The jump of live messenger never worked but good list. I didn't have the will to uninstall them, clean and reinstall. It was just the messenger.

  After media player jumplist that I started looking on the Internet, but nothing has worked, sfc scannow, the antivirus is mse, and I never changed anything. After that, also started to pop-up Windows defender turned off at startup and then also stopped workin the eco mode selection button and the button display to open mediaplayer.
  What can I do?

  I also updated the BIOS and I have the latest Windows.

  Sorry for the long post ;)
  Thanks to all in advance!
  cyaaao!

  Hi mate

  I'm not very well if this problem could be related to an error in Win 7 m.
  But everything looks like it could be the case

  In my case the jumplist will appear when I do a right-click on the IE icon or the Windows Media icon placed in the taskbar on the left side.

  I searched a bit a found this MS Jumplist page and how to handle this:
  http://Windows.Microsoft.com/en-us/Windows7/using-jump-lists-to-open-programs-and-items

  Maybe this could be useful for managing the jumplist.

• Tecra R840-16J - FN keys no function

  Hello

  I have a problem with my Tecra R840-16J. Sometimes, I use the FN keys (the most I use is F6 and F7 for brightness) sometimes I can't! They are disabled singles! And if I press on the window of "windows Mobility Center" ECO button will be displayed and the brightness will be there if the F6/F7 keys are still active and will not be there if the keys are not active more!

  This laptop is driving me crazy! I have Toshiba laptops from the end of 1997 (Ant) working again... with win98 a MX30 which is perfect despite almost 8 years of use intensive Ant sub zero temperatures (I do astrophotography...) but this one which I thought it would be a professional is a great diapointment... !

  Thanks for any help,
  Paulo

  Hello Paulo

  I put t really know what the problem is here and why do you have this problem, but without cleaning preinstalled OS (factory settings) something like that shouldn't happen.

  What you can try is to remove preinstalled Toshiba value added package, restart the system and install the latest version of the Toshiba download page - http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp

  Please post comments.

• Tecra R840 WLAN sporadically not have access to internet or router

  Hello

  A few days ago I baught a Tecra R840. Everything works fine but the WLAN adapter. Basically, Internet works, but sporadically - especcially during downloading files - the wlan adapter loses the connection to internet/router.

  It is always connected to the router at full speed, but it says 'limited access' and the download is interrupted. I then manually disconnect the network and then reconnect, it sometimes takes 2 or 3 tries. But it still works for a few minutes.

  You have an idea, what can be the reason for this problem?

  Concerning

  Martin

  Post edited by: moadin80

  Hello

  There are some things that should be considered;
  -Update the WLan driver
  -Deactivation of energy saving for the WLan

  Did you check both?
  If this isn't the case, please update the WLan driver.
  In addition go to Win 7 power management and disable the WLan to save energy.
  In many cases, this affects the Wlan functionality.

  If your router has been set to 802. 11 G, then you must choose this also on your laptop. Reach:
  Panel-> card Wlan-> properties-> Advanced tab
  Here you will find a few different options that can improve performance. I m not very well what settings you have for each wireless network card supports different options.

• Satellite P750 - Eco mode automatically

  Hey guys!

  So, I use this model for a while, and I can't say something bad to her.

  What I recently started the experience is the following and it repeats every time when on.

  First of all, when I turn on the machine, Toshiba Buletin Board appears. I thought it was because it is right next to the gas station, there is an alert icon.

  I clik above, go back and alert fires.
  I thought it's because I didn't created backup, but that good, I never had.

  That, when I leave the laptop for a few minutes, and when he should light, it activates ecomode himself (beeps hot keys), and if I leave after that, when it is about to turn out to fall asleep, she often starts a beep and flashes quick access key for volumizing upward. In this situation, it often turns off the coast of the wireless adapter.

  Thank you
  FF

  With regard to the Eco Mode.
  This mode is controlled by preinstalled Toshiba Eco Utility and it slightly decreases the performance of certain devices to reduce electric energy consumption

  Please consult this documentation from Toshiba
  https://APS2.toshiba-tro.de/KB0/FAQ2503AT0000R01.htm

  Click on the help button to get more details on this tool.

  By the way: Toshiba Bulletin Board starts automatically when you start. To avoid this, you can disable this service in the msconfig. In run, type msconfig. Click on the Start button and uncheck the entry of Bulletin Board. Save the changes and reboot.

• Tecra R840-S8450 - power problems - help with Blink Codes

  Looking for help, thinking on the right track, but want to confirm and get things fixed.

  Have a Tecra R840-S8450 that is having power problems. When you try to start it, the orange plug light flashes a code. This code is 01001010 which I derived shortlong short short long short long short flashes of orange electric light.

  It is great progress, assuming that I have translated as right to 52 h, which is equivalent to 'EVER5V voltage is under or equal to 4.5V when the computer is '.
  Start ". However it don't tell me what is wrong so that I can try to do something about it.

  Would be grateful for the help, thanks,

  David

  Of course quite here, is that no one from Toshiba has the manual to find codes?

  Posted by dgwbdavid
  

  Looking for help, thinking on the right track, but want to confirm and get things fixed.

  Have a Tecra R840-S8450 that is having power problems. When you try to start it, the orange plug light flashes a code. This code is 01001010 which I derived shortlong short short long short long short flashes of orange electric light.

  It is great progress, assuming that I have translated as right to 52 h, which is equivalent to 'EVER5V voltage is under or equal to 4.5V when the computer is '.
  Start ". However it don't tell me what is wrong so that I can try to do something about it.

  Would be grateful for the help, thanks,

  David

• Tecra R840 - Ethernet and driver sound Dynadock question

  Hey,.

  Tecra R840, model PT429A-007004, does not work with the Toshiba dyna docking station.

  Specifically, the Ethernet and the audio driver for the dock dyna is not installed after running or installing the driver on the cd of the dock dyna or the latest driver on the site.

  Does anyone know a fix for this?

  Note: nothing in Device Manager to say that these pilots to dock a missing, only when you install the driver mentioned the wizard that Ethernet and audio drivers might not be installed.

  He also mentions that the dynadock has a problem with the graphics card edge, but we have not had problems with graphics, for example screens.

  > where to install the driver only mention Assistant that Ethernet and audio drivers might not be installed.

  _Regarding the driver LAN and Audio missing. _
  This theme has been discussed already in this thread
  http://forums.computers.Toshiba-euro...ThreadId=70771

  _The possible solution: _
  Navigate to the folder * C:\Program Files\DisplayLink Core Software *
  And here you should find the drivers for the network and its

• USB does not wake up after Tecra R840 goes to sleep

  Hello

  I have a Toshiba Tecra R840 on windows 7 sp1. I use a USB mouse, but whenever I put my laptop to sleep I have to go out and re put the dongle insert it again.

  I've changed the following power options:
  Under devices, USB, USB Root Hub power management "allow the computer to tun turn off this device to save power" is not checked

  It goes the same for generic Hub
  Under control panel, power options, USB, USB selective parameter settings is disabled.

  Does anyone have any suggestions?
  Thank you
  Tony

  Have hmmm you tried to remove/delete the USB hubs and controllers from Device Manager and install it again?
  Usually after restart again the system should automatically find the drivers and needs to be reinstalled all USB controllers once more