Telnet buffer issues

Similar Questions

• Parity errors & read on Serial Port framing

  Hello, I am writing a program that reads the serial port IR thermometer. Intermittently I get parity so many framing errors and can't explain why or find a way to remedy. All the parameters of the series were double checked and controlled. I don't get any errors when you use HyperTerminal yet, when I do test bed in MAX, I see these mistakes from time to time. I tried the suggestions of the knowledge base for these as presenting a delay between the Visa set up and read the Visa or flushing buffer issue before reading, but none worked. Any idea or ideas would be appreciated.

  In addition, while searching through discussions on parity and framing errors, I saw a when a user recommends the following: "use wait event triggered by the stop character and when the error occurs, I just deleted the error, empty the buffer (wait the next stop character) and reread." If that sounds like a good solution, how would I go about its implementation?

  I've attached a screenshot of my reading series loop so you can see what I'm doing. I do about the error code control timeout is.

  Given that you have activated the stop character, you should not use the bytes to the serial port. You shouldn't have to delay or any function buffer flush.

  PS, You also have to change the way your loop exits.

• Cannot find listed in the file Readme S61 bugid

  I try to display the list of signatures that have been disabled in the S61 upgrade. The bugid that is given to us is CSCec88388. I keep says that it does not find this identifier. Can someone check if this is the right ID or link to this bug, please?

  Thank you.

  I don't know why he is not visible.

  I see very well.

  It could be that the system can tell I am a user of Cisco internal and shows me the details while he won't see them not an external viewer.

  I'll check into it.

  In the meantime, here's the list of signatures that have been removed (they had their)

  setting Enabled set to False, for their re - allow to set simply their active parameter true) because they are for older vulnerabilities not seen in the latest version of the OS or the patch is released for some time. These signatures disabling save resources system on sensors and increases the overall performance of sensor.

  Here is the list of signatures:

  1000.0 BAD IP OPTION

  Ten of 1001.0 record Packet

  1002.0 Timestamp

  1003.0 provide s, c, h, CBT

  1005.0 SATNET ID

  1201.0 frag overlap

  2153.0 attack Smurf ICMP

  3001.0 TCP Port Scan

  3042.0 TCP END package

  3100.0 SMTP RCPT TO: Bounce

  3101.0 SMTP for: Bounce

  3103.0 SMTP (EXPN or VRFY)

  3103.1 SMTP (EXPN or VRFY)

  3104.0 archaic SMTP

  3104.1 archaic SMTP

  3105.0 decode the SMTP

  3107.0 attack SMTP Majordomo

  3108.0 overflow of content MIME SMTP

  3111.0 W32 Sircam Malicious Code

  3111.1 W32 Sircam Malicious Code

  Back of the e-mail loop 3112,0 lotus Notes

  3114.0 Code to run arbitrary Fetchmail

  3117.0 worm KLEZ

  3117.1 worm KLEZ

  3120.0 virus of ANTS

  3120.1 virus of ANTS

  3125.0 address of the postfix 1.1.12 back envelope

  3126.0 postfix bounce scan

  3153.0 FTP address incorrect

  3154.0 the wrong FTP port

  3162.0 glFtpD LIST back

  heap corruption 3163.0 wu-ftpd

  3164.0 Server Instant Mini Portal Directory Traversal

  3165.0 FTP SITE EXEC

  3200.0 phf WWW

  3204.0 WWW .bat file

  3208.0 attack of campas WWW

  3209.0 attack of WWW server overview

  3210,0 WWW IIS discovers Source Bug

  3210,1 WWW IIS discovers Source Bug

  3210,2 WWW IIS discovers Source Bug

  3210,3 WWW IIS discovers Source Bug

  3212.0 bug WWW NPH-TEST-CGI

  WWW 3213.0 TEST-CGI Bug

  3215.0 DOT DOT IIS RUN attack

  3216.0 crossing WWW directory... /...

  3217.0 view WWW php Bug file

  3218.0 film WWW IMS bug

  3219.0 for php WWW buffer overflow

  3221.0 WWW View Source GGI Bug

  WWW 3222.0 CGI MLOG/MYLOG Bug

  3223.0 Manager WWW CGI BUG

  3224.0 WWW Webgais Bug

  3225.0 WWW websendmail file access

  3226.0 WWW Webdist Bug

  3227.0 WWW Htmlscript Bug

  3228.0 WWW performer Bug

  3229.0 win-c-sample Web site buffer overflow

  3230.0 Web site upload

  3231.0 Novell convert Bug

  3233.0 County-cgi WWW overflow

  3306.0 SMB remote registry access attempt

  3307.0 red SMB recognition

  3401.0 IFS = /.

  3401.1 IFS.

  3405.0 proxy with gateway Telnet Buffer Overflow

  3451.0 BearShare Directory Traversal

  gopherd 3452.0 halidate overflow

  3455.0 Java Web Server Cmd Exec

  3456.0 Solaris in.fingerd information leakage

  3456.1 Solaris in.fingerd information leakage

  3456.3 Solaris in.fingerd information leakage

  3457.0 finger root shell

  3458.0 overflow game invite AIM

  ValiCert forms.exe overflow 3459.0

  ValiCert forms.exe overflow 3459.1

  3461.0 finger probe

  3462.0 finger Redirect

  3463.0 root finger

  3464.0 access to the file in the finger

  rlogin 3500.0 - froot

  3701,0 oracle 9iAS Web Cache Buffer Overflow

  3705.0 overflow of Tivoli Storage Manager Client Acceptor

  3707.0 fingerd Perl command Exec

  3734.0 overflow of Cfengine

  BO2K-TCP-nonStealth 3990.1

  BO2K-TCP-nonStealth 3990.2

  BO2K-TCP-XOR 3991.0

  BO2K-TCP-Stealth 3992.1

  3992.2 BO2K-TCP-Stealth

  BO2K-TCP-Stealth 3992.3

  BO2K-TCP-Stealth 3992.4

  BO2K-TCP-Stealth 3992.5

  4053.0 invades-Original-UDP

  B02K-UDP 4055.1

  4061.0 Echo, Chargen back

  4150.0 mount Kill

  4506.0 D-Link Wireless SNMP Plain text password

  5034.0 attack newdsn IIS WWW

  5035.0 WWW faxsurvey?

  5037.0 WWW MachineInfo attempt

  WWW wwwsql file read Bug 5038.0

  5041.0 attack of anyform WWW

  5043.1 WWW Cold Fusion attack

  5043.2 WWW Cold Fusion attack

  5043.3 WWW Cold Fusion attack

  5044.0 attack WWW Webcom.se guestbook

  5048.0 attack WWW IIS BAT EXE

  5049.0 access WWW IIS showcode.asp

  5050.0 WWW IIS .htr overflow

  5052.0 WWW VTI open attempt

  5053.0 attempt to list bin WWW VTI

  5054.0 WWW WWWBoard attack

  5057.0 WWW Sambar samples

  5057.1 WWW Sambar samples

  5058.0 attack of info2www WWW

  5059.0 WWW Alibaba attack

  5059.1 WWW Alibaba attack

  5059.2 WWW Alibaba attack

  5060.0 WWW excite AT - generate.cgi access

  5061.0 access catalog_type.asp WWW

  5062.0 attack classifieds.cgi WWW

  5063.0 access dbmlparser.exe WWW

  5064.0 attack imagemap.cgi WWW

  5065.0 attack infosrch.cgi WWW IRIX

  5067.0 attack plusmail WWW

  5068.0 access formmail.pl WWW

  5069.0 attack whois_raw.cgi WWW

  5072.0 attack bizdb1 - search.cgi WWW

  5073.0 WWW EZShopper loadpage.cgi attack

  5074.0 WWW EZShopper search.cgi attack

  5075.0 WWW IIS Virtualized UNC Bug

  5076.0 bug WWW webplus

  5077.0 WWW excite AT - admin.cgi access

  5078.0 passwd WWW Piranha attack

  5079.0 WWW CMA MySQL admin access

  5080.0 access WWW IBM WebSphere

  5083.0 access by FTP in virtual Vision WWW browser

  5084.0 WWW Alibaba attack 2

  5084.1 WWW Alibaba attack 2

  5085.0 access WWW IIS Source Fragment

  5086.0 WWW WEBactive Logfile access

  5087.0 WWW Sun Java Server access

  5087.1 WWW Sun Java Server access

  5088.0 access WWW Akopia View_page.html

  5089.0 access to directory WWW Big Brother

  5090.0 htimage.exe WWW Frontpage access

  5091.0 WWW Cart32 Remote Admin Access

  5091.1 WWW Cart32 Remote Admin Access

  5092.0 access WWW CGI-world survey it

  5093.0 access admin.php3 WWW PHP-Nuke

  5095.0 attack WWW CGI Script Center Account Manager

  5096.0 WWW CGI Script Center subscribe attack me

  5097.0 attack WWW FrontPage MS-DOS device

  5097.1 attack WWW FrontPage MS-DOS device

  5097.2 attack WWW FrontPage MS-DOS device

  5099.0 access WWW GWScripts News Publisher

  List goes in the next post (there is a limit on the number of characters in a post so I can't put the whole list in a post)

• Netflix should sue sony

  Netflix should sue sony for blame it shit streaming on them, when in fact it's the sony/dvd player that does not... I have the sony bdps270 and I can, t watch netflix on it because it either freezes in loading or lets me watch about 2 minutes and then locks into place... something new is that this happens all the time now... at least three times this week I had to use my computer to look at who is on a wireless network, while the dvd is connected directly. You can blame it on my ISP and netflix, but why I can watch on my pc and it loads in like 5 seconds without stopping or reloading?
  I do not watch tv on my computer screen when I could be watching it in my living room on a big TV... and the only reason why I bought the player was to the netflix. Many times I felt like red going on this thing and he break just to small bites... it's as if someone is playing keep away with my TV and I am so frustrated.
  A promise, never again will I buy a sony brand anything... and I will be progressively all my sony branded products. Why the ps3 which is intended for the work of better game player whose only purpose is to watch movies? More important still why keep you throwing everyone under the bus when it is very obvious that your product/service is the problem? Above all, why did you not corrected it since it is very obvious that many many of your customers have exactly the same problem? Why do you continue to lie to your customers and to blame others for your failure. You lose a huge amount of business and product/brand loyalty. Fix your servers or let us broadcast directly from netflix. Fix it it fix it!

  The article you sent me contains some good information, but nothing that I didn't already know.   Blue Ray model I mentioned, the BDP-S380 comes enabled with a RJ-45 port network.  I connected it to my router.  I've never had buffereing or freezing with YouTube, Hulu or Amazon Video, on this piece of equipment.

  The considerable amount of internet discussion on Sony Blue Ray players and this problem with Netflix, I have a few questions:

  (1) is it true that these devices of Sony not to go directly to Netflix, but are redirected via Sony servers that must collect and send new data streaming?

  (2) Sony also road Hulu, YouTube, Amazon, or other streaming through their servers services or allow them direct access to these providers?

  Something else interesting to note would be the following: when I start an episode of Netflix, this player does everything first a screen indicating that the network connection is tested and gives me an indication of average speed.  Then she actually starts streaming the episode, again give me an indication of speed average until he has buffered upward and status information disappears from the display.  I noticed that in all cases, the network connection test which takes place first of all always gives an average speed that is superior to the buffering real of the episode.  Also, I ran the network to other devices before speed tests, during and after the Sony Reader showed me what he thinks, what is speed.  These tests may come from my iPad using SpeedTestX, one of my PC using various utilities through the diagnostic software and network support in my router.  In all cases, these tests are 1-3 MB faster than watch the Sony player.  The average speed displayed on the screen is also 1-3 MB faster with Amazon as Netflix and Amazon, the test speed is always the same as the speed of buffering.

  So, from my observations, it is easy to conclude that the re - direct traffic of Netflix through the servers of Sony is what is causing slow and put connections into buffer issues.  They are not present with any other streaming service I use, or they are on my other devices not Sony blue ray.

• Sound / Audio (CRAC, pop, broken playback) the buffer Y460P issues

  Hello

  I have problems playing audio without clicks and pops. They sound like problems of buffer against the recess.

  Clicks occur during audio playback of any program, but worsen under certain cercumstances.

  The worst time is when I have my external monitor plugged. He actually 10 times worse if I have uTorrent with multiple files running. Even after closing, the clicks remain. The best result is obtained only after the closure of the programmes as much as possible.

  The clicks are better, but not completely disappeared, when no other monitor is connected and cover is open. If I close the lid, the clicks well gets worse.

  I have an external USB sound (Sound Blaster X - FI) card and also tried with this. It makes no difference, the clicks are stll there.

  I updated my BIOS with the latest version and sound card drivers are updated. Is there anything else I can try?

  Thanks and let me know if you need more information from System.

  
  

• Telnet issue... What am I doing wrong?

  OK, I have two configuration network to see them via the VPN. The VPN is provided by a 515e and a 501F catalogue. 515e 192.168.50.0 network, the network 501F to the catalog is 192.168.51.0

  External ip address of the 515e is x.x.71.7, the 501 is x.x.71.8

  Problem: I cannot telnet to the 192.168.51.0 behind the 501 network in the external interface of the 515e, but can't leave network 50.0 behind the 515e in the external interface of the 501F catalogue.

  Here is my configuration:

  515E-

  IP address outside the x.x.71.7

  IP address inside 192.168.50.1

  permit access ip host x.x.71.7 192.168.51.0 list inside_nat0_outbound 255.255.255.0 (hitcnt = 1184)

  inside_nat0_outbound 192.168.50.0 ip access list allow 255.255.255.0 host x.x.71.8 (hitcnt = 62)

  501F to the catalog-

  IP address outside the x.x.71.8

  IP address inside the 192.168.51.1

  inside_nat0_outbound ip 192.168.51.0 access list allow 255.255.255.0 host x.x.71.7

  permit ip host x.x.71.8 192.168.50.0 access list inside_nat0_outbound 255.255.255.0

  Why this work one way, but not back? I would have thought that if it worked enough for me to telnet from the side 501 at the 515, then the same configuration would work the 515 at the 501 but does not appear.

  Thank you for your help in advance.

  Dave

  Hi Dave,.

  Look at my comments about Telnet in the previous announcement.

  A few questions for you:

  1. in your config on the Pix 501, whey you have two instructions in your access list.

  inside_nat0_outbound 192.168.50.0 ip access list allow 255.255.255.0 192.168.51.0 255.255.255.0

  permit access ip host x.x.71.7 192.168.51.0 list inside_nat0_outbound 255.255.255.0

  2 and also use a different access list for address matching and NAT 0 cos you will encounter problems when you set up multiple vpn tunnels.

  For Ex:

  crypto VPNMAP 10 card matches the address 100

  access-list 100 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  crypto VPNMAP 20 card matches the address 101

  access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0

  access-list 150 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  access-list 150 permit ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0

  NAT (inside) - 0 150 access list

  Kind regards

  Arul

• Telnet issue

  If the switches without user name and password, we cannot telnet in.

  But what happens if Acess Point without one, are we able to telnet in?

  (1) Yes you will be

  (2) you need local connection

  (3) Yes (bbb)

  (4) no... you have a password or use the local connection.

  Here is a link that will help you better understand.

  http://www.Cisco.com/en/us/products/SW/iosswrel/ps1818/products_configuration_example09186a0080204528.shtml#PW-line

• Issue of Telnet and SSH on Cisco 3750.

  I turn on Cisco 3750 and everything so I wasn't able to connect in the area. I even changed the source interface and update transport under the VTY lines input method, no luck.

  Can I choose to disable SSH by removing the corresponding lines of configs and RSA keys. And I changed the entry to transport back to Telnet. After the reboot of the switch, I'm still not able to connect despite the fact that the box is accessible.

  Any help?

  Thank you

  Jean-Marie

  Hello

  This should help to confirm the configuration and troubleshooting SSH on your device: -.

  http://www.Cisco.com/c/en/us/support/docs/security-VPN/Secure-Shell-SSH/4145-SSH.html

  I hope this helps.
  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• PIX 501 - issues with Telnet

  I'm currently pre configuration of the firewall, so I had to build a small network to test the configuration. I am able to telnet system when I plug my laptop into the hub inside the firewall. However, when I plug on the external interface and the external address of the box telnet it seems to connect but I get no feedback eventually, he abandoned the connection. I'm trying to telnet on port 25 (to mimic the smtp traffic), the telnet server has been configured to listen on this port. When I try to telnet on 23 he refuses the connection almost immediately. Its almost like the PIX meets the demand of telnet instead of the destination system. I am able to get responses from the system with various icmp traffic.

  I have a static (inside, outside) mapping for the system I want to telnet to port 25.

  Any ideas?

  Thanks in advance.

  I would say that. The correction prevents would-be hackers to get HELP and your server smtp VRFY. You will also see:

  220 * 0 * 200 * 0 * 0200, instead of what type of server, etc.

  Glad to be of service.

  Byron

• NEITHER 9212 - issues with sampling frequency, number of samples and size of buffer or slowness comes together with thermocouple module

  To begin with, I am very new to labview and unfortunately on that my first task is to build something rather complicated for a project that my company works. Fortunately it is especially followed rather than control critical processes.

  Currently, I have a cDAQ with modules, DI, AO, and TC.

  cDAQ-9133

  NEITHER 9472

  NEITHER 9421

  NEITHER 9263

  NEITHER 9205

  NEITHER 9212

  I'm currently running read-write for all 5 of these modules in parallel while loops and analog and digital inputs/outputs modules that all work as expected. Each loop requires 1 sample per channel through the wizard DAQmx etc for each module and I got can interact with all the asyncronosly inputs and outputs which at the moment is the goal. I can switch power switch for each module save memory, or if the need arrives later.

  My problem is that the module TC (NI 9212) when tilt on which allows the acquisition of sample 1 loop seems to take much, much longer to collect samples. I have played with different acquisition parameters and can seem to get a continuous flow of data when you use streaming samples, or even when specifying N-samples but I come in questions where the "application cannot catch up with the hardware.

  I tried to find an optimal number of samples/sampling, rate, etc I can get an update of temperature more than every 1 to 2 seconds, but if I set the number of samples that are high enough to apparently get a constant flow, what ends up happening waveform graphs seem to lag behind the actual data, and that's where I get errors. I only want 1 sample per channel per cycle anyway. Yet once, all the other modules in the cycle with less than 100ms delay between acquisitions but the module thermocouple ends up being 1-2 seconds. It's okay because in our application temperature should not rise/drop very quickly but its boring nonetheless.

  I have the acquisition set up for the same (NI 9212) thermocouple module was like my modules of analog and digital inputs (NI 9205 and NI 9421) take 1 sample every time the task is called so I'm having a hard time understand why do the same for the TC module introduced such a delay. Max sampling rate is supposed to be 95 samples/s/ch, so I guess that the delay must come from call the task over and over again in a loop.

  Synchronization and how you have configured the 9212?

  In the case of high resolution, it can reach 1.8 samples/s. see page 7 of the plug technique here for rates for the supported modes:

  http://www.NI.com/PDF/manuals/374389a.PDF

  -AK2DM

• Ssh/telnet/web ASA5505 question

  I can't access this ASA everywhere except the console.

  I'm no expert, ASA, but I compared it to others I have configured asa, and I can't find the error of my ways.

  It is expected to be easy, I just need a different set of eyes looking at it now. I hope I don't have too much censor, but I imagine that if I am able to SSH locally, will fix all issues of access I have.

  :
  ASA Version 7.2 (4)
  !
  host name X
  domain X.local
  activate the encrypted password of XXXXXXXXXXXXXXXXXXX
  passwd encrypted XXXXXXXXXXXXXXXX
  names of
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.27.1 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP address dhcp setroute
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !

  Banner motd to USE OFFICIAL ONLY. Unauthorized use prohibited
  Banner motd people who use this computer system is subject to having all
  Banner motd of their activities on this system monitored and recorded without
  new notice of Banner motd. Audit of users may include surveillance of the strike.

  boot system Disk0: / asa821 - k8.bin
  passive FTP mode
  clock timezone CST - 6
  clock to summer time recurring CDT
  DNS lookup field inside
  DNS domain-lookup outside
  DNS server-group DefaultDNS
  Server name X.X.X.12
  Name-Server 4.2.2.2
  domain pain.local
  permit same-security-traffic intra-interface
  object-group service XX tcp - udp
  60000 64999 object-port Beach
  object-group network MySpace
  object-network 67.134.143.0 255.255.255.0
  object-network 204.16.32.0 255.255.255.0
  network-object 216.178.32.0 255.255.224.0
  object-group network Facebook
  object-network 69.63.176.0 255.255.255.0
  object-network 204.15.20.0 255.255.255.0
  object-group Protocol TCPUDP
  object-protocol udp
  object-tcp protocol
  the DM_INLINE_NETWORK_1 object-group network
  object-network 10.x.x.0 255.255.255.0
  object-network 172.x.x.0 255.255.255.0
  object-network 10.x.x.0 255.255.255.0
  object-network 10.x.x.0 255.255.255.0
  object-network 10.x.x.0 255.255.255.0
  object-network 172.x.x.0 255.255.255.0
  the LocalLAN object-group network
  X subnet Local 192.168.27.x description
  object-network 192.168.27.0 255.255.255.0
  the DM_INLINE_NETWORK_2 object-group network
  object-network 10.x.x.0 255.255.255.0
  object-network 10.x.x.0 255.255.255.0
  object-network 10.x.x.0 255.255.255.0
  object-network 10.x.x.0 255.255.255.0
  object-network 172.x.x.0 255.255.255.0
  object-network 172.x.x.0 255.255.255.0
  the DM_INLINE_NETWORK_3 object-group network
  network-host 64.x.x.x object
  network-host 71.x.x.x object
  network-host 74.x.x.x object
  network-host 99.x.x.x object
  network-host 173.x.x.x object
  object-network 192.168.27.0 255.255.255.0
  object-network 192.168.1.0 255.255.255.0
  192.168.27.0 IP Access-list extended sheep 255.255.255.0 allow object-group DM_INLINE_NETWORK_1
  outgoing extended access-list deny ip any object-group inactive MySpace
  outgoing extended access-list deny ip any object-group inactive Facebook
  outgoing to the icmp a whole allowed extended access list
  coming out to the one permitted all ip extended access list
  extended access-list extended permitted ip object-LocalLAN group DM_INLINE_NETWORK_1 object
  outside_access_in list extended access allowed object-group ip DM_INLINE_NETWORK_3 all
  outside_cryptomap list extended access permitted ip object-group LocalLAN-group of objects DM_INLINE_NETWORK_2
  pager lines 24
  Enable logging
  timestamp of the record
  registration of emergency critical list level
  exploitation forest-size of the buffer 1048576
  emergency logging console
  monitor debug logging
  recording of debug trap
  notifications of logging asdm
  address record [email protected] / * /
  exploitation forest-address recipient [email protected] / * / level of errors
  exploitation forest-address recipient [email protected] / * / critical level
  logging feature 23
  forest-hostdown operating permits
  registration of emergency of class auth trap
  record labels of class config trap
  record labels of class ospf trap
  logging of alerts for the vpn trap class
  Within 1500 MTU
  Outside 1500 MTU
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any inside
  ICMP allow all outside
  ASDM image disk0: / asdm - 621.bin
  don't allow no asdm history
  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 0 access-list sheep
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Access-group outside_access_in in interface outside
  Route outside 0.0.0.0 0.0.0.0 192.168.X.X 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  AAA authentication enable LOCAL console
  the ssh LOCAL console AAA authentication
  AAA authentication http LOCAL console
  Enable http server
  x.x.x.x 255.255.255.255 out http
  http 0.0.0.0 0.0.0.0 outdoors
  http 0.0.0.0 0.0.0.0 inside
  http 192.168.1.0 255.255.255.0 inside
  http 192.168.27.0 255.255.255.0 inside
  redirect http outside 80
  No snmp server location
  No snmp Server contact
  Community SNMP-server
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Sysopt connection tcpmss 1360
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec df - bit clear-df outdoors
  card crypto outside_map 2 match address outside_cryptomap
  card crypto outside_map 2 set pfs
  card crypto outside_map 2 peers set x.x.x.x
  card crypto outside_map 2 game of transformation-ESP-AES-128-SHA
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  aes encryption
  sha hash
  Group 5
  life 86400
  crypto ISAKMP policy 20
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400
  enable client-implementation to date
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 inside
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 60
  Console timeout 0
  management-access inside
  dhcpd 10.x.x.x 4.2.2.2 dns
  dhcpd field pain.local
  dhcpd outside auto_config
  dhcpd option 156 ascii ftpservers = 10.x.x.x
  dhcpd option 42 ip 208.66.175.36
  !
  dhcpd address 192.168.27.2 - 192.168.27.33 inside
  dhcpd allow inside
  !

  NTP-1 md5 authentication key *.
  authenticate the NTP
  NTP server 10.x.x.x source inside
  username XXXXXXXXX XXXXXXXXXXXXXX encrypted privilege 15 password
  tunnel-group 64.X.X.X type ipsec-l2l
  IPSec-attributes tunnel-group 64.X.X.X
  pre-shared key X
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
  : end

  The party concerned to control where you are allowed to SSH in the ASA are these lines:

  ssh 0.0.0.0 0.0.0.0 inside
  ssh 0.0.0.0 0.0.0.0 outside
  

  But you have generated public/private keys?

  ASA (config) # crypto key generate rsa key general module 2048

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• How can I stop firefox in delay/suspended momentarily (5-10 seconds) when I try and a large video/application of buffer?

  Hello

  When I try to buffer a large video (youtube HD) or the even more lag - to perform a speedtest

  animation for speedtest occupies about 3 images - about 4-6 seconds apart, as with youtube, he puts in buffer 2 seconds - then firefox hangs for about 12 seconds - when he comes back he is fully buffered

  has raised this issue since I got new Internet (download 76mbit) and it is not my rig like youtube and speedtest.net run perfectly smooth in chrome (but I don't like chrome or the google customer support)

  I already tried enabling/disabling of hardware acceleration and tried a bit of tinkering - anything else that you can suggest? (propose any adjustments-i'll try anything)

  Thank you for your time

  You can check the problems caused by the recent updates of Flash and try these:

  • disable an eventual extension of the browser for Firefox Plugin RealPlayer Record and if installed RealPlayer update
  • disable the safe_mode in Flash 11.3 and later versions
  • turn off hardware acceleration in the Flash plugin
  • http://KB.mozillazine.org/Flash#troubleshooting

• How to clear the output buffer, possibly resize and burn again, before you begin the task of output

  I use PyDAQmx with a USB-6363, but I think the question is generic to DAQmx.

  I have an output buffer that I want to be able to (re) write to without starting the task output.

  More specifically, I have a graphical interface and a few sliders, the user can move.  Whenever the slider changes, a new set of values is loaded into the buffer output through DAQmxWriteAnalogF64.  After you set the value, the user can click on a button and start the task output.

  In some cases the change in cursor does not require a change in buffer size, only a change in the data.  In this case, I get the compalint following DAQmx as they tried writing:

  The generation is not yet started, and not enough space is available in the buffer.

  Set a larger buffer, or start the generation before writing data more than content in the buffer.
  Property: DAQmx_Write_RelativeTo
  Value: DAQmx_Val_CurrWritePos
  Property: DAQmx_Write_Offset
  Corresponding value: 0
  Property: DAQmx_Buf_Output_BufSize
  Corresponding value: 92

  In other cases the change in cursor requires both change in the size of the buffer and data modification.  In this case, I get the following, but only after that do a few times each time increase the size of the writing.

  DAQmx writing failed because a previous writing DAQmx configured automatically the size of output buffer. The size of the buffer is equal the number of samples written by channel, so no additional data can be written before the original task.

  Start the generation of before the second writing DAQmx or set true in all instances of writing DAQmx Auto Start. To gradually write to the buffer before starting the task, call DAQmx Configure an output buffer before the first writing DAQmx.
  Task name: _unnamedTask<0>

  State code:-200547
  function DAQmxWriteAnalogF64

  I tried to configure the output via DAQmxCfgOutputBuffer buffer (in some cases, by setting it to zero or a samples, then save again, in an attempt to clear it) but that doesn't seem to do the trick.

  Of course, I can work around the problem by loading data only when the user clicks the end button, but not what I'm asking here.

  Is it possible to "remake" the writing of output before you begin the task?

  Thank you

  Michael

  Today I have no material practical to validate, but try unreserving task before writing the new buffer:

  DAQmxTaskControl (taskHandle, DAQmx_Val_Task_Unreserve);

  With a simulated device, he made the error go away in case the buffer is the same size.  You will need to validate if the data are in fact correct, but I think it should be (unreserving I would say reset the write pointer so the old buffer are replaced with the new data).

  I always get errors when you try to change the size of buffer if (on my 6351 simulated).  I posted some similar mistakes about the reconfiguration of the tasks here, I guess it is possible that this issue has also been set at 9.8 (I always use 9.7.5 on this computer).  If the behavior is still present in the new driver, and also appears on real hardware (not just simulated), then it seems that this is a bug of DAQmx someone at OR should be considered.

  I wrote a simple LabVIEW VI that captures the error in order to help people to NOT reproduce it:

  

  The best solution at the moment would be likely to re-create the task if you need to change the size of the buffer (or avoid writing data until you are sure what will be the size of buffer).

  Best regards

• Possible to set up buffer - delay in the implementation of large number of buffers - IMAQ trigger problem

  Hi all

  I thought that I could transfer it here because it might be a more appropriate forum. I have a bit of time pressure, so I hope someone can help me. I'm having a problem with a program that I wrote to acquire and store images from a camera to linear scan.

  My camera (SUI Goodrich, 1024 pixels) is connected to a card framegrabber (PCIe-1427), which is connected via a RTSI cable to a PCI-6731 card attached to a SCC-68 (series) connector M.  My goal is to drive a mirror galvanometer scanning and acquire images from the camera continuously on each scan. As the galvo scan will be the frame of an image (1024 pixels x 1024 lines).

  I managed to do it (I think), as my direct purchase program works exactly as I expected. However, when I try to save the images, I noticed that for a larger number of images, the starting point of the image is shifted the same amount for each image. I'm not really sure what's going on, it seems to me that there is a delay in the use of the VI "IMAQ set up buffer" when a larger number of buffers is used, (or even 100). Is it possible that my hardware trigger does not wait for all buffers to be configured before you start to run?

  I would really appreciate any idea or ideas that anyone could have on this issue.

  Sincere greetings,

  Gill

  I fixed the problem by doing that I don't use actually 1000 stamps to save 1000 frames. Program works if the number of buffers is lowered.

• Circular buffer asynchronous read with crush

  Trying to accomplish the following without success so far:

  Setup a a DAQmx read buffer in a manner such that

  • all cost overruns are allowed
  
  
  • can read a buffer half at any time (entire buffer will not work, due to the following requirement)
  
  
  • read is compared to sample the most recent, If no data was read before or not.

  If I'm really asynchronous, I should get the more recent samples (which a party may or may not be 'old' or reading of the previous call) without delay at any time I choose to call it DAQmx Read. So far, I get a dleay compatible with a demi-tampons of a data value.

  Play with the following parameters did me not what I was looking for. I thought that the following combination might work:

  Crush the unread samples

  Reading Relative to the most recent

  Read size = size of buffer/2

  I can do this separately without the DAQ buffer; This isn't the issue. Call it an exercise if you wish - I'm just curious to know if this can be done with the DAQmx read buffer.

  I guess what I'm wondering really is if the pointer of the playback Position can be ignored.

  That works very well, thank you.