Terminating a VPN to an interface series

Similar Questions

• Easy VPN setup with interface to multiples with the same level of security

  Hello

  I want to configure an ASA 5505 with 7.2 (4) software and dual license ISP and when I configure two interfaces with the level 0 on two security interfaces and enable vpnclient the trace message appear:

  ERROR: Cannot determine the internal and external interfaces Easy VPN remote: multiple interfaces with the same levels of security.

  vpnlclient of configuration above:

  vpnclient Server x.x.x.x where x.x.x.x
  vpnclient mode network-extension-mode
  vpnclient nem-st-autoconnect
  vpnclient TUNNEL_EZVPN_TUNNELSPEC vpngroup password *.
  vpnclient username usr_ezvpn_tunnelspec password *.
  vpnclient enable

  interfaces:

  interface Vlan200
  nameif outside1
  security-level 0
  IP x.x.x.x 255.255.255.252
  !
  interface Vlan300
  nameif outside2
  security-level 1
  IP x.x.x.x 255.255.255.128
  !

  monitor the SLA to the routing:

  monitor SLA 100
  type echo protocol ipIcmpEcho 200.221.2.45 interface outside1
  NUM-package of 5
  frequency 30
  monitor als 100 calendar life never start-time now
  ALS 200 monitor
  type echo protocol ipIcmpEcho 200.154.56.80 interface outside2
  NUM-package of 5
  frequency 30
  Annex monitor SLA 200 life never start-time now
  ALS 300 monitor
  type echo protocol ipIcmpEcho 4.2.2.1 interface outside1
  NUM-package of 5
  frequency 30
  Annex monitor SLA 300 life never start-time now
  ALS 400 monitor
  type echo protocol ipIcmpEcho 200.244.168.149 interface outside1
  NUM-package of 5
  Timeout 3000
  threshold of 3000
  frequency 30
  Annex monitor SLA 400 life never start-time now

  Follow-up:

  !
  track 1 rtr 400 accessibility
  !
  Track 2 rtr 200 accessibility
  !

  routes:

  Route 0.0.0.0 outside1 0.0.0.0 x.x.x.x 100 track 1
  Route 0.0.0.0 outside2 0.0.0.0 x.x.x.x 200 track 2

  The track works normal.

  Kind regards!

  Try using the command "backup interface" on the secondary ISP interface.

  http://www.Cisco.com/en/us/docs/security/ASA/asa72/command/reference/b_72.html#wp1338585

  You need to increase the level of security to 1 for this interface.

  By default, EasyVPN uses the highest level of safety inside and the lowest outside.  Anything between the two must be set manually.  I assume you have an interior vlan defined but not added to the posted config.

• WEB - VPN in outsite interface

  Hi all

  I'm putting a WebVPN, but I have a problem when the vpn through outsite interface access.

  If I put inside the interface for web vpn users allowed, access is normally done, but outside the interface is not possible.

  Debug displays the message "can't find political IKE initiator.

  Configuration:

  WebVPN

  port 444

  allow outside

  allow inside

  Auto-signon allow ip 172.17.2.35 255.255.255.255 type auth ntlm

  remote type tunnel-group WEBVPN access

  attributes global-tunnel-group WEBVPN

  authentication-server-group LOCAL AD_LDAP

  I try to access between the link https://ASAIP:444

  OBS: I can get telnet using port 444 on the external interface

  Can someone help me?

  TKS a lot.

  Rafael Mendes

  Why don't you just remove the ACL of the dynamic encryption card? that should be the case and the two connections will work.

  Thank you

• 3945 site VPN termination - not on p2p connect interface

  Nice day!

  Our border router connects to the ISP router with a subnet of p2p. The IP address on our router connect interface cannot be used for other services such as VPN. Provider filters all packets with this address defined in an IP header. Therefore, we must use the addresses of the other publicly routed subnet. I understand that we can place another router behind this border router and set his foreign address as an address on that subnet 'admitted '. But we want to offer this service on the same edge router. Is this possible? I tried to put the card encryption on a loopback interface and the traffic directly to it for encryption.

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key address z.z.172.2 no-xauth

  crypto ipsec transform-set TRANS1 esp-3des esp-sha-hmac

  crypto map VPN 10 ipsec-isakmp

  set peer z.z.172.2

  set transform-set TRANS1

  match address CRYPTO_ACL

  interface loopback0

  description -= VPN Termination =-

  ip address x.x.127.111 255.255.255.255

  crypto map VPN

  interface GigabitEthernet0/0.10

  description -= ISP Gateway =-

  encapsulation dot1Q 10

  ip address y.y.122.203 255.255.255.248

  interface GigabitEthernet0/0.20

  description -= LAN =-

  encapsulation dot1Q 20

  ip address 192.168.10.1 255.255.255.0

  ip route 0.0.0.0 0.0.0.0 y.y.122.201

  ip route 192.168.100.0 255.255.255.0 loopback 0

  ip access-list extended CRYPTO_ACL

  permit ip 192.168.10.0 0.0.0.255 192.168.100.0 0.0.0.255

  I does not work. The packet does not get encrypted but simply routed to the ISP router.

  Please, help.

  Thanks.

  Viktor,

  I believe crypto map on loopback interface is still unsupported but I have not been following this in the past.

  The way we do it, is apply the actul crypto map to physical/logical interface facing the ISP BUT you tweak the crypto map to use loopback as it's local address.

  In your case it'd look like this:

  crypto map VPN local-address loopback0

  In this place all everyone will think that this tunnel is established with the address assigned to the interface loopback0.

  Hope this helps,

  Marcin

• Terminating the VPN Client on multiple interfaces PIX

  Hello people

  Does anyone know if it is possible to configure a PIX 515 to complete VPN clients on more than one interface?

  Specifically, we strive to allow client VPN access to the internet and the DMZ through to the internal network.

  See you soon

  Simon

  It is sure, in fact if you want to have customers come in and then be able to route back on another LAN-to-LAN tunnel, then this is how you do it.

  Here there is an example of a config:

  http://www.Cisco.com/warp/public/110/client-pixhub.html

• bad terminator in the Basler A504k CIM series

  I'm talking about in series of LV to a Basler A504k via a NOR-1429th and, despite what says in the compatibility report and in this post, I perfectly managed, at least as long as I tried. A (still unpolished) example of my order that VI is attached (LV8.6.1), for the sake of anyone running in my same problems.

  However, there is one thing that bothers me about the string terminator defined in the file of the camera. The original definition is

  TermChars (\x06)

  This is not correct.  \x06 is the character of the acknowledgement of receipt sent by the camera to recognize the command sent by the host was correctly formed; the channels are normally end with ETX, i.e. \x03, while the camera can be answered by a single NAK, i.e. \x15, if the query string is incorrect. For this device, the command for a reading sequence is (when it is correct) STX-query - ETX-> ACK-STX-response-ETX, so if ACK is used as an indicator of end, the response to the reading of orders is always lost. At least, so much as "IMAQ Serial Read.vi" is used; given that the format of the camera control is strict, an alternative using 'IMAQ series Read Bytes.vi' and the exact number of characters to read would still be possible.

  It was simple to change the TermChars to (\x03) entry in the file of the camera and with whom my VI essentially works, while the replay would not be with the bad terminator.  The only whim so far I am aware, is that I seem to be able to set Timer1 and Timer2, settings that control the rate of time and part of the exhibition, but not to reread, contrary to what the manual says (the camera meets always 0).

  Any comments on that?

  Enrico

  Correction to what I wrote just above - fixed read a number of bytes is required anyway, because the answer may contain binary camera the \x03 or whether in the data field. It was actually the reason why I couldn't read some specific areas, such as versions of firmware or the timer data.

  A corrected version of my previous vi is attached. As for me, the problem is now resolved - this message in one concern for others in my situation.

• Termination of VPN on Pix behind router IOS with private subnet

  OK, basically, I wonder if it is possible to terminate a VPN connection on a Pix 506 Firewall which is behind a router IOS. The public interface of the Pix 506 have a private on a 29 ip address will IOS within the interface. Network is configured as follows:

  Internet as 10Base T

  | (5 public - X.X.X.34. 38)

  | (In WIC-1ENET)

  | (.34 assigned to interface)

  Cisco 1760

  | (Pomp) | (WIC-4PORTSWITCH)

  | | (10.0.0.1 29 on 1760)

  Net private Pix 506

  (192.168.1.0) (10.0.0.2 29 on Pix)

  Now, two internal interfaces of the 1760 are configured to PAT on the IP of the interface of the 1760 and all internet traffic goes perfectly. None of the access lists are currently applied anywhere on the 1760 and a static translation on the 1760 is configured pour.35 to 10.0.0.2 ('public' ip pix). RDP and other services authorized in the pix access list work perfectly well from the outside world when you enter a.35, but if I try to terminate a VPN from a pix 501 for the pix 506 offsite using the Intellectuelle.35 property, it does not work.

  Is it possible to do this type of work setting.

  I realize I could put an external switch to 1760 and run the public subnet directly and individually in the 1760 and Pix 506, however, I really would prefer not no need to do so if it is possible to avoid it.

  Remove the crypto map to the interface on the PIX and reapply.

• Can the customer vpn to pix interface unprotected to a protected interface

  I have a pix multi-interface, the description of the interface is as follows:

  Outside-> 10MB to ISP

  Inside-> vlan main

  DMZ-> Web servers, etc...

  Lab1-> test application servers

  LAB2-> test application servers

  etc...

  Comments wireless-> free wireless (connected to the Cisco WAP)

  The open wireless only has access to the internet, not one of the reliable networks. It is an untrusted interface (security lvl 1). The external interface is security 0.

  I want to be able to allow vpn access from the wireless in networks of trust like vpn from outside (internet) is processed.

  I guess that the pix sees a vpn connection attempt to another of its interfaces.

  The client times out connecting since the wireless for the pix outside IP interface.

  The pix records simply this:

  January 20, 2009 13:38:23: % 7-710005-PIX: UDP request and eliminated from 192.168.20.5/1346 to GuestWireless:yy.yy.yy.yy/500

  the external interface IP = yy.yy.yy.yy

  the pix is also the dhcp server for wireless network connections.

  Is it still possible? If so, what Miss me?

  Thank you

  Dave

  To answer: -.

  The leg wireless of the PIX is the security level 1, and the external interface is the security level 0. That would not mean that vpn is launched from a higher to a lower security interface? Yes but the traffic is clear--asked to terminate a VPN connection to an interface that is locally attached to the PIX effectivly in the inside of the unit. Sure that PIX will refuse the connection he received on the external interface of the interface without comment thread.

  No it isn't the same thing, something like: -.

  crypto ISAKMP enable GuestWireless - this indicates the PIX to listen and accept connections VPN ISAKMP/issues of ANY device connected to this interface FOR the GuestWireless interface.

  HTH >

• HP laserjet 1100 - what is a parallel interface or interface series?

  I have a HP LaserJet 1100 printer. Works fine on my old desktop pc. I recently replaced the office with a laptop of HP under Win7. My question is this: can I connect the printer to my laptop? I think that the interface of the printer is a parallel port; is that correct? Are there devices out there that can convert a parallel interface for a series/usb interface? And finally, this printer can be controlled with Win7?

  Hey Mitch,.

  Thanks for the information continues.  For installation information using the driver OS package, please read the following link.

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?objectID=c02536257

  The 1100 series you provided the product number to use a standard parallel port and not the Mini Centronics.  The cable that you have linked with parallel to USB would be the best bet to make this work.

  Jason

• Terminating the VPN client on 871W

  Hello

  I tried to install EasyVPN on a cisco 871W by SDM. The goal is to finish the VPN client with authentication with an external RADIUS/advertising (on a local subnet). I implemented the IAS on a win2003 Server advertising and checked the accounts.

  SDM was missing the 'crypto map' piece of config. After you add this in the CLI it still didn't work. Thus, EasyVPN is not as easy at is sounds...

  Could someone with some knowledge of VPN and IPsec and so forth please look at this config? Maybe it gives me an idea of what I did wrong (which, without a doubt, must be the case).

  Thank you

  Erik

  ==

  AAA new-model
  !
  AAA rad_eap radius server group
  auth-port 1645 10.128.7.5 Server acct-port 1646
  !
  AAA rad_mac radius server group
  !
  AAA rad_acct radius server group
  !
  AAA rad_admin radius server group
  !
  AAA server Ganymede group + tac_admin
  !
  AAA rad_pmip radius server group
  !
  RADIUS server AAA dummy group
  !
  AAA authentication login default local
  AAA authentication login eap_methods group rad_eap
  AAA authentication login mac_methods local
  AAA authentication login sdm_vpn_xauth_ml_1 local
  AAA authorization exec default local
  AAA authorization ipmobile default group rad_pmip
  AAA authorization sdm_vpn_group_ml_1 LAN
  AAA accounting network acct_methods
  action-type market / stop
  Group rad_acct
  !
  !
  !
  AAA - the id of the joint session
  clock timezone MET 1
  clock to DST DST PUTS recurring last Sun Mar 02:00 last Sun Oct 02:00
  !
  Crypto pki trustpoint TP-self-signed-1278336536
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 1278336536
  revocation checking no
  rsakeypair TP-self-signed-1278336536
  !
  !
  TP-self-signed-1278336536 crypto pki certificate chain
  certificate self-signed 01
  3082024A 308201B 3 A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
  2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
  69666963 31323738 33333635 6174652D 3336301E 170 3039 31303237 32313237
  32395A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
  4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 32373833 65642D
  33363533 3630819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
  81008B 56 5902F5DF FCE1A56E 3A63350E 45956514 1767EF73 FEC6CD16 7E982A82
  B0AF8546 ABB3D35A B7C3A7E3 3ACCB34A 8B655C97 F103DBD5 9AAEFEFC 37A 02103
  4EFC398B 0C8B6BE5 AD3E568E 6CB69F87 CBCA0785 EAED0A28 726F2F0A B0B0453E
  32E6B3B7 861F87FA 222197DD 3410D8A9 35939E9B CBF95F20 B8DA6ADE BF460F5C
  BF8F0203 010001A 3 72307030 130101 1 FF040530 030101FF 301D 0603 0F060355
  551 1104 16301482 12444341 4E495430 302E6361 6E2D6974 2E657530 1F060355
  1 230418 30168014 84C9223E 661B2EB4 5BAB0B0E 1BE3A27A 64B3AEB0 301D 0603
  551D0E04 16041484 C9111E66 1B2EB45B AB0B0E1B E3A27A64 B3AEB030 0D06092A
  010104 05000381 8693B 599 70EC1F1A D2995276 F3E4AF9D 81002F4A 0D 864886F7
  17E3583A 46C749F9 38743E6F F5E60478 5B9B5091 E944C689 7BA6DCA2 94D2FBD3
  AFDE4500 A0A3644E 603A852D 55ED7A87 93501D5C 1662DAED 3FFFEC5A F1C38ED4
  E0787561 BA5C14A3 6D065FCF 7DBDEBB6 9186C2D9 AA253FBF A9E38BC3 342C3AC9
  2BEF6821 E4C50277 493AD5B6 2AFE
  quit smoking
  dot11 syslog
  !
  IP source-route
  !
  !
  DHCP excluded-address IP 10.128.1.250 10.128.1.254
  DHCP excluded-address IP 10.128.150.250 10.128.150.254
  DHCP excluded-address IP 10.128.7.0 10.128.7.100
  DHCP excluded-address IP 10.128.7.250 10.128.7.254
  !
  pool IP dhcp VLAN30-COMMENTS
  import all
  Network 10.128.1.0 255.255.255.0
  router by default - 10.128.1.254
  10.128.7.5 DNS server
  -10.128.7.5 NetBIOS name server
  aaa.com domain name
  4 rental
  !
  IP dhcp VLAN20-STAFF pool
  import all
  Network 10.128.150.0 255.255.255.0
  router by default - 10.128.150.254
  10.128.7.5 DNS server
  -10.128.7.5 NetBIOS name server
  aaa.com domain name
  4 rental
  !
  IP dhcp SERVERS VLAN10 pool
  import all
  Network 10.128.7.0 255.255.255.0
  router by default - 10.128.7.254
  10.128.7.5 DNS server
  -10.128.7.5 NetBIOS name server
  aaa.com domain name
  4 rental
  !
  !
  IP cef
  no ip domain search
  IP domain name aaa.com
  inspect the tcp IP MYFW name
  inspect the IP udp MYFW name
  No ipv6 cef
  !
  Authenticated MultiLink bundle-name Panel
  !
  VPDN enable
  !
  !
  !
  username privilege 15 secret 5 xxxx xxxx
  !
  !
  crypto ISAKMP policy 1
  BA 3des
  preshared authentication
  Group 2
  !
  ISAKMP crypto client configuration group vpn
  key xxxx
  pool SDM_POOL_1
  netmask 255.255.255.0
  !
  !
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  !
  crypto dynamic-map SDM_DYNMAP_1 1
  market arriere-route
  !
  !
  card crypto SDM_CMAP_1 client authentication list sdm_vpn_xauth_ml_1
  map SDM_CMAP_1 isakmp authorization list sdm_vpn_group_ml_1 crypto
  client configuration address map SDM_CMAP_1 crypto answer
  map SDM_CMAP_1 65535-isakmp dynamic SDM_DYNMAP_1 ipsec crypto
  !
  Crypto ctcp port 10000
  Archives
  The config log
  hidekeys
  !
  !
  !
  Bridge IRB
  !
  !
  interface Loopback0
  10.128.201.1 the IP 255.255.255.255
  map SDM_CMAP_1 crypto
  !
  interface FastEthernet0
  switchport access vlan 10
  !
  interface FastEthernet1
  switchport access vlan 20
  !
  interface FastEthernet2
  switchport access vlan 10
  !
  interface FastEthernet3
  switchport access vlan 30
  !
  interface FastEthernet4
  no ip address
  Speed 100
  full-duplex
  PPPoE enable global group
  PPPoE-client dial-pool-number 1
  No cdp enable
  !
  interface Dot11Radio0
  no ip address
  Shutdown
  No dot11 extensions aironet
  !
  interface Vlan1
  address IP AAA. BBB. CCC.177 255.255.255.240
  no ip redirection
  no ip proxy-arp
  NAT outside IP
  no ip virtual-reassembly
  No autostate
  Hold-queue 100 on
  !
  interface Vlan10
  SERVER description
  no ip address
  IP nat inside
  no ip virtual-reassembly
  No autostate
  Bridge-group 10
  Bridge-group of 10 disabled spanning
  !
  interface Vlan20
  Description of the STAFF
  no ip address
  IP nat inside
  no ip virtual-reassembly
  No autostate
  Bridge-group 20
  Bridge-group 20 covering people with reduced mobility
  !
  Vlan30 interface
  Description COMMENTS
  no ip address
  IP nat inside
  no ip virtual-reassembly
  No autostate
  Bridge-group 30
  Bridge-group 30 covering people with reduced mobility
  !
  interface Dialer1
  MTU 1492
  IP unnumbered Vlan1
  no ip redirection
  no ip proxy-arp
  NAT outside IP
  inspect the MYFW over IP
  IP virtual-reassembly
  encapsulation ppp
  Dialer pool 1
  Dialer-Group 1
  PPP authentication pap callin
  PPP pap sent-name of user password 7 xxxx xxxxx
  !
  interface BVI10
  Description the server network bridge
  IP 10.128.7.254 255.255.255.0
  IP nat inside
  IP virtual-reassembly
  !
  interface BVI20
  Description personal network bridge
  IP 10.128.150.254 255.255.255.0
  IP nat inside
  IP virtual-reassembly
  !
  interface BVI30
  Bridge network invited description
  IP 10.128.1.254 255.255.255.0
  IP access-group Guest-ACL in
  IP nat inside
  IP virtual-reassembly
  !
  pool of local SDM_POOL_1 192.168.2.1 IP 192.168.2.100
  IP forward-Protocol ND
  IP route 0.0.0.0 0.0.0.0 Dialer1
  IP http server
  access-class 2 IP http
  local IP http authentication
  IP http secure server
  IP http secure ciphersuite 3des-ede-cbc-sha
  IP http secure-client-auth
  IP http timeout policy slowed down 60 life 86400 request 10000
  !
  !
  overload of IP nat inside source list 101 interface Vlan1
  IP nat inside source static tcp 10.128.7.1 25 AAA. BBB. Expandable 25 CCC.178
  IP nat inside source static tcp 10.128.7.1 80 AAA. BBB. CCC.178 extensible 80
  IP nat inside source static tcp 10.128.7.1 443 AAA. BBB. CCC.178 extensible 443
  IP nat inside source static tcp 10.128.7.1 8333 AAA. BBB. CCC.178 extensible 8333
  IP nat inside source static tcp 10.128.7.2 25 AAA. BBB. Expandable 25 CCC.179
  IP nat inside source static tcp 10.128.7.2 80 AAA. BBB. CCC.179 extensible 80
  IP nat inside source static tcp 10.128.7.2 443 AAA. BBB. CCC.179 extensible 443
  IP nat inside source static tcp 10.128.7.2 8333 AAA. BBB. CCC.179 extensible 8333
  IP nat inside source static tcp 10.128.7.3 25 AAA. BBB. Expandable 25 CCC.180
  IP nat inside source static tcp 10.128.7.3 80 AAA. BBB. CCC.180 extensible 80
  IP nat inside source static tcp 10.128.7.3 443 AAA. BBB. CCC.180 extensible 443
  IP nat inside source static tcp 10.128.7.3 8333 AAA. BBB. CCC.180 extensible 8333
  IP nat inside source static tcp 10.128.7.4 25 AAA. BBB. Expandable 25 CCC.181
  IP nat inside source static tcp 10.128.7.4 80 AAA. BBB. CCC.181 extensible 80
  IP nat inside source static tcp 10.128.7.4 443 AAA. BBB. CCC.181 extensible 443
  IP nat inside source static tcp 10.128.7.4 8333 AAA. BBB. CCC.181 extensible 8333
  IP nat inside source static tcp 10.128.7.5 25 AAA. BBB. Expandable 25 CCC.182
  IP nat inside source static tcp 10.128.7.5 80 AAA. BBB. CCC.182 extensible 80
  IP nat inside source static tcp 10.128.7.5 443 AAA. BBB. CCC.182 extensible 443
  IP nat inside source static tcp 10.128.7.5 8333 AAA. BBB. CCC.182 extensible 8333
  IP nat inside source static tcp 10.128.7.6 25 AAA. BBB. Expandable 25 CCC.183
  IP nat inside source static tcp 10.128.7.6 80 AAA. BBB. CCC.183 extensible 80
  IP nat inside source static tcp 10.128.7.6 443 AAA. BBB. CCC.183 extensible 443
  IP nat inside source static tcp 10.128.7.6 8333 AAA. BBB. CCC.183 extensible 8333
  IP nat inside source static tcp 10.128.7.7 25 AAA. BBB. Expandable 25 CCC.184
  IP nat inside source static tcp 10.128.7.7 80 AAA. BBB. CCC.184 extensible 80
  IP nat inside source static tcp 10.128.7.7 443 AAA. BBB. CCC.184 extensible 443
  IP nat inside source static tcp 10.128.7.7 8333 AAA. BBB. CCC.184 extensible 8333
  IP nat inside source static tcp 10.128.7.8 25 AAA. BBB. Expandable 25 CCC.185
  IP nat inside source static tcp 10.128.7.8 80 AAA. BBB. CCC.185 extensible 80
  IP nat inside source static tcp 10.128.7.8 443 AAA. BBB. CCC.185 extensible 443
  IP nat inside source static tcp 10.128.7.8 8333 AAA. BBB. CCC.185 extensible 8333
  IP nat inside source static tcp 10.128.7.9 25 AAA. BBB. Expandable 25 CCC.186
  IP nat inside source static tcp 10.128.7.9 80 AAA. BBB. CCC.186 extensible 80
  IP nat inside source static tcp 10.128.7.9 443 AAA. BBB. CCC.186 extensible 443
  IP nat inside source static tcp 10.128.7.9 8333 AAA. BBB. CCC.186 extensible 8333
  IP nat inside source static tcp 10.128.7.10 25 AAA. BBB. Expandable 25 CCC.187
  IP nat inside source static tcp 10.128.7.10 80 AAA. BBB. CCC.187 extensible 80
  IP nat inside source static tcp 10.128.7.10 443 AAA. BBB. CCC.187 extensible 443
  IP nat inside source static tcp 10.128.7.10 8333 AAA. BBB. CCC.187 extensible 8333
  IP nat inside source static tcp 10.128.7.11 25 AAA. BBB. Expandable 25 CCC.188
  IP nat inside source static tcp 10.128.7.11 80 AAA. BBB. CCC.188 extensible 80
  IP nat inside source static tcp 10.128.7.11 443 AAA. BBB. CCC.188 extensible 443
  IP nat inside source static tcp 10.128.7.11 8333 AAA. BBB. CCC.188 extensible 8333
  IP nat inside source static tcp 10.128.7.12 25 AAA. BBB. Expandable 25 CCC.189
  IP nat inside source static tcp 10.128.7.12 80 AAA. BBB. CCC.189 extensible 80
  IP nat inside source static tcp 10.128.7.12 443 AAA. BBB. CCC.189 extensible 443
  IP nat inside source static tcp 10.128.7.12 8333 AAA. BBB. CCC.189 extensible 8333
  !
  Guest-ACL extended IP access list
  deny ip any 10.128.7.0 0.0.0.255
  deny ip any 10.128.150.0 0.0.0.255
  allow an ip
  IP Internet traffic inbound-ACL extended access list
  allow udp any eq bootps any eq bootpc
  permit any any icmp echo
  permit any any icmp echo response
  permit icmp any any traceroute
  allow a gre
  allow an esp
  !
  access-list 1 permit 10.128.7.0 0.0.0.255
  access-list 1 permit 10.128.150.0 0.0.0.255
  access-list 1 permit 10.128.1.0 0.0.0.255
  access-list 2 allow 10.0.0.0 0.255.255.255
  access-list 2 refuse any
  access-list 101 permit ip 10.128.7.0 0.0.0.255 any
  access-list 101 permit ip 10.128.150.0 0.0.0.255 any
  access-list 101 permit ip 10.128.1.0 0.0.0.255 any
  Dialer-list 1 ip Protocol 1
  !
  !
  !
  !
  format of server RADIUS attribute 32 include-in-access-req hour
  RADIUS-server host 10.128.7.5 auth-port 1645 acct-port 1646 borders 7 xxxxx
  RADIUS vsa server send accounting
  !
  control plan
  !
  IP route 10 bridge
  IP road bridge 20
  IP road bridge 30
  Banner motd ^.
  Unauthorized access prohibited. *
  All access attempts are logged! ***************

  ^
  !
  Line con 0
  password 7 xxxx
  no activation of the modem
  line to 0
  line vty 0 4
  access-class 2
  privilege level 15
  transport input telnet ssh
  !
  max-task-time 5000 Planner
  AAA.BBB.CCC.ddd NTP server
  end

  Erik,

  The address pool you are talking about is to assign to the customer or the public router interface?  If you want to set up your vpn client software point a full domain name instead of an IP address that you can do it too long you can ensure the use of the name is resolved by a DNS SERVER.

  The range of addresses that you can be asigned to your Dialer interface will depend on your ISP.

  -Butterfly

• Site to Site VPN using an interface to Peer and LAN

  Hello

  I have an ASA 5580 to the site to site VPN with our partner. VPN connection is through my external interface and Local for the VPN network comes from the external interface too. Is it possible to do? Thank you.

  drawing2.jpg

  

  The layout you describe is contrary to the concept of basic firewall of the approved facility and no approved interfaces (upper and lower security level).

  If your LAN is on the external interface, which is to stop remote users simply access it directly?

• site to site vpn with ASA 5500 series SSL?

  We have routers DLink DIR - 130 5505 s ASA and PIXen, all work well with our PIX 515E, we need to replace.

  We also have Internet satellite in two places. High latency makes IPsec VPN to DLinks on these very slow sites.

  We were informed by HughesNet that a SSL VPN will mitigate some of the problems of latency.

  However, we cannot use a VPN client for the biometric timeclocks in these places, the clocks need static IP addresses and are more or less "dumb terminals".

  The machine of series 5000 ASA VPN site to site similar to OpenVPN or only the most comment client-server type SSL VPN connections?

  Thank you, Tom

  Hi Thomas,

  The SSL VPN on ASAs feature is a client/server relationship where the remote computer can connect without client (browser) or clientbased (AnyConnect) to the ASA.

  Federico.

• VPN for small offices - series 2811 vs RV

  Hi all

  Need advice

  I have a question about this material to use for a small remote office.

  We currently have

  • 5 users
  • 5 7941 phones
  • 1 2811 (series, 2 FXS and 1 FXO)
  • 1 3560g

  All voice devices are controlled by a CUCM 9 in our main offices. The 2811 is also an MGCP gateway.

  Currently, they connect via a T1, that management wants to disconnect the reason for its high cost, the T1 is connected to a 2811 (C2800NM-ADVENTERPRISEK9-M) with the serial port and analog lines, behind the router, we a 3560 G 24 port (POE) with everyone connected.

  They asked me to see if its possible to pass to a VPN site-to-site and possibly replace the 2811 and 3560 g with a much smaller device might be an all in one.

  I've been looking around, and I did not any small business router that meets our needs. A tech colleague suggested looking in the RV series routers, but I don't see devices providing telephone services.

  Any suggestions would be greatly appreciated.

  Thanks in advance

  Assuming you have a Cisco 2800/3800 series or better, at Headquarters, I would stick with the 2811 router and make a site to site VPN tunnel. You can actually register the phones through the tunnel and then use SRST for relief when the tunnel falls. Of course, preventing the phones to make and receive calls without the tunnel, but at least they will be able to talk to each other. If you are really worried about having at least a work phone then the internet connection breaks down at the remote desktop, you can buy a single line of POTS of the telco and run it on your FXO port. This line would serve for only emergency calls if you fall the tunnel. Nevertheless, the 2811 is much more powerful than the RV series (excluding the part on one of the models RV wireless).

• VPN with NAT Interface

  Hello

  I am trying to set up a VPN between a VLAN I have defined and another office. I have been using nat on the interface for internet access with a NAT pool.

  I created the VPN with crypto card and the VPN is successfully registered.

  The problem I encounter is that with NAT is enabled, internet access is working but I can ping through the VPN.

  If I disable NAT, VPN works perfectly, but then him VLAN cannot access the internet.

  What should I do differently?

  Here is the config:

  Feature: 2911 with security package

  Local network: 10.10.104.0/24

  Remote network: 192.168.1.0/24

  Public beach: 65.49.46.68/28

  crypto ISAKMP policy 104

  BA 3des

  preshared authentication

  Group 2

  lifetime 28800

  ISAKMP crypto key REDACTED address 75.76.102.50

  Crypto ipsec transform-set esp-3des esp-sha-hmac strongsha

  OFFICE 104 ipsec-isakmp crypto map

  defined by peer 75.76.102.50

  Set transform-set strongsha

  match address 104

  interface GigabitEthernet0/0

  IP 65.49.46.68 255.255.255.240

  penetration of the IP stream

  NAT outside IP

  IP virtual-reassembly

  full duplex

  Speed 100

  standby mode 0 ip 65.49.46.70

  0 6 2 sleep timers

  standby 0 preempt

  card crypto OFFICE WAN redundancy

  interface GigabitEthernet0/2.104

  encapsulation dot1Q 104

  IP 10.10.104.254 255.255.255.0

  IP nat pool wan_access 65.49.46.70 65.49.46.70 prefix length 28

  overload of IP nat inside source list 99 pool wan_access

  access-list 99 permit 10.10.104.0 0.0.0.255

  access-list 104. allow ip 10.10.104.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 104. allow ip 192.168.1.0 0.0.0.255 10.10.104.0 0.0.0.255

  access-list 104 allow icmp 10.10.104.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 104 allow icmp 192.168.1.0 0.0.0.255 10.10.104.0 0.0.0.255

  ISAKMP crypto #sh her

  IPv4 Crypto ISAKMP Security Association

  DST CBC conn-State id

  65.49.46.70 75.76.102.50 QM_IDLE 1299 ACTIVE

  Hello!

  Please, make these changes:

  extended Internet-NAT IP access list

  deny ip 10.10.104.0 0.0.0.255 192.168.1.0 0.0.0.255

  IP 10.10.104.0 allow 0.0.0.255 any

  IP nat inside source list Internet-NAT pool access-wan overload

  * Please do not remove the old NAT instance until you add that above.

  Please hold me.

  Thank you!

  Sent by Cisco Support technique Android app

• Two IPSec VPN on an interface does not

  Hello

  I'm actually trying to bring two IPSec VPN on a single interface. I managed to create a tunnel between hand and Barcelona and between by and Mad. But I can't create it between Barcelona and Mad.

  We have a cisco ISR1921 Mad Barcelona and a nominal Netgear.

  Config of Barcelona:

  
crypto isakmp policy 10encr 3desauthentication pre-sharegroup 2lifetime 28800crypto isakmp key PAR_KEY address PAR_IP no-xauthcrypto isakmp key MAD_KEY address MAD_IP no-xauth!!crypto ipsec transform-set ESP_3DES_MD5 esp-3des esp-md5-hmaccrypto ipsec transform-set ESP_3DES_SHA1 esp-3des esp-sha-hmaccrypto ipsec transform-set ESP_3DES esp-3des!crypto map outside_map 10 ipsec-isakmpset peer MAD_IPset transform-set ESP_3DES_SHA1set pfs group2match address 120crypto map outside_map 20 ipsec-isakmpset peer PAR_IPset transform-set ESP_3DES_SHA1 ESP_3DES_MD5 ESP_3DESset pfs group2match address 110access-list 110 permit ip 10.40.42.0 0.0.1.255 10.20.42.0 0.0.1.255access-list 120 permit ip 10.40.42.0 0.0.1.255 10.60.42.0 0.0.1.255

  Crazy conf:

  crypto isakmp policy 10encr 3desauthentication pre-sharegroup 2lifetime 28800crypto isakmp key PAR_KEY address PAR_IP no-xauthcrypto isakmp key BARCELONE_KEY address BARCELONE_IP no-xauth!!crypto ipsec transform-set ESP_3DES_MD5 esp-3des esp-md5-hmaccrypto ipsec transform-set ESP_3DES_SHA1 esp-3des esp-sha-hmaccrypto ipsec transform-set ESP_3DES esp-3des!crypto map outside_map 20 ipsec-isakmpset peer PAR_IPset transform-set ESP_3DES_SHA1 ESP_3DES_MD5 ESP_3DESset pfs group2match address 110crypto map outside_map 30 ipsec-isakmpset peer BARCELONE_IPset transform-set ESP_3DES_SHA1set pfs group2match address 120access-list 110 permit ip 10.60.42.0 0.0.1.255 10.20.42.0 0.0.1.255access-list 120 permit ip 10.60.42.0 0.0.1.255 10.40.42.0 0.0.1.255

  Now the weird part:

  I have absolutely NO LOG AT ALL. I don't have them when the tunnel with normal is negotiated, but I have absolutely nothing to Mad-Barcelona. Not even an error message or anything like that.

  Negotiations between Barcelona and the Mad is nowhere.

  Someone has an idea, what happens?

  I'm thinking that he might not start the tunnel and does not all newspapers:

  -you see all success in the used card encryption access list?

  -is it possible that there is a problem of connectivity between sites?

  -There is a NAT (or PAT) which may affect the set of addresses?

  -is it possible that routing to one of the sites is not going through the interface that has the encryption card?

  Maybe if you post production show card crypto that there could be a few clues about the problem?

  HTH

  Rick