the correct configuration of zones

Similar Questions

• The correct configuration on the redundancy help

  Hello

  We have a VMware ESXi 3 hosts 4.1 with two Equallogic ps4000 infrastructuer, an AIRLOCK and one with SATA drives.

  It is connected with 2 switches, where everything is connected, so redundancy "should" work.

  On ESXi server, we have 8 network ports, in vCenter, we used 2 NICs for the management and vmotion, 2 for iScsi traffic and 2 for network access VLAN.

  Some time ago, one of our switches failed, and all the VM rebooted because they lose the connection, 2-3 minutes later they came back on the use of the other switch, but it should not happen. I did a little research and discovered that perhaps consolidation of NETWORK cards has not been configured no doubt.

  On vSwitch 2 where will my Iscsi traffic, I used a VMkernel port on both network adapters, it should work, right? What have I done wrong? Someone has an idea, what configuration should be placed on the consolidation of NETWORK cards to do this work.

  After a bit of trouble, I clicked on change properties on vSwitch 2, clicked VMkernel port ISCSi, hget to exepotions political in nic teaming configuration. Failover detection network: Link status notification only, switches: Yes, the failback: No.

  When I disconnected the cable, vmwares worked, when I unplugged the swich, RM of vm. I heard when using network cards, should I create the vmkernel ports on this vswitch using redundancy, is this true? I also thought that the ISCSI port group traffic would inherit the rights of the nicteaming, but this happens for some reason any. Someone has an idea of this network which is the best practice, when you configure the redundancy with multiple cards in vCenter?

  Thx for all the help.

  Bit of an old thread, but in the possibility it has not been resolved, here's your answer:

  With Equallogic units, you will need to configure a vmkernel by physical uplink port.

  1 vSwitch

  2 unique physical network (vmnic3, for example vmnic4) cards

  2 vmkernel ports

  -vmk1-> override set failover of vmnic3 active and vmnic4 unused

  -vmk2-> override unused vmnic4 set failover active and vmnic3

  Bind the vmkernel ports to the iscsi hba software and configure storage.  To improve the performance set up frames on all vswitches, switches and vmk.

• What is the correct configuration of ESX host IP

  I guess you could say Im having a moment of self-doubt.

  Im sure this has been answered, and if you know the link, I would be very grateful if you could point me in the right direction.

  The question is, is it recommended or does have the ESX hosts on a different IP range for the rest of the VM?

  Our SAN has a different ip address range and vmotion has a different ip address range.

  What is the best practice for this?

  Thanks for your help.

  Different logical networks and, if possible, different networks (with VLAN or physical switches).

  If you use VLAN you can use only 2 NICs (instead of 4) for SC and vMotion and difficulty preferred a NIC for each portgroup

• By selecting the correct configuration of monitor

  I just got a new Dell Ultrasharp U2410 monitor. It has a "Preset Mode" in which I choose sRGB or Adobe RGB (among other options).

  I'm about to calibrate the monitor and would like to know how can I choose?

  The system environment: LR 3.2/PS4, Win7 64-bit.

  Panagon-

  If it is useful, I have a U2410 I profiling using a SpyderPro elite. My 'best' results were in Standard mode with burst the value 18 (to get it down to about 120 cd/m2 as Pete says) and contrast, set to 50.

  I put 'better' in quotes because it depends on your goals. My goal was to get the widest range on the screen (a little reason to pay for this expensive monitor), then use the test in Photoshop if I needed to see how an image was going to go in a smaller space like sRGB. I did some research to confirm that Standard is the way to go here, but I don't have the links.

  Any software profiling you use, all I've seen is a chart showing how your range overlaps with standard color spaces in the end. Use the settings above, I have had my U2410 so be little bigger than AdobeRGB. I hope this helps.

  DB

• Correct configuration for access Fiber Channel AAA

  Hello all, I have searched for the correct configuration access the MDS 9124 fibre channel passes to the CSACS 1121 with 5.4.

  I find pieces, but I'm probably set up groups incorrectly.

  On the side of the switch, I have this:

  FiberA (config) # executed sho | include the aaa

  AAA server Ganymede group + sasTac +.

  AAA server Ganymede group + yokTac +.

  RADIUS AAA radius server group

  AAA authentication login default group sasTac +.

  Accounting sasTac AAA + default group

  RADIUS-server key 7 "09754F021046461S020731".

  RADIUS-server host 10.7.4.22 touch 7 'fewhg '.

  RADIUS-server host 10.207.5.21 touch 7 'fewhg '.

  RADIUS-server host 10.207.5.22 touch 7 'fewhg '.

  RADIUS-server host 10.7.4.23 touch 7 '09754F021046461C020731 '.

  RADIUS-server host 10.7.4.24 touch 7 '09754F021046461C020731 '.

  AAA server Ganymede group + sasTac +.

  Server 10.207.5.21

  Server 10.207.5.22

  AAA server Ganymede group + yokTac +.

  Server 10.7.4.22

  RADIUS AAA radius server group

  On the side of the ACS, I have cisco-av-pair = shell: roles = 'admin network' for the command set.

  Groups in the switch are the remains of the previous configuration; However, I can't find the setting anywhere in the old ACS version 3.3.

  On the post of Jatin Katyal, I found links to explain the implementation of devices, but the links are dead.

  EJ

  I am pleased that you guessed it running. Thank you for posting to the forum and let us know that you fixed it and what you have done to address them. This information could be useful to some other drive in the forum who will work with these switches at some point. It's this kind of information sharing that makes the forum so useful and valuable.

  HTH

  Rick

• How can I configure my system clock to match the correct local time

  How can I configure my system clock to match the correct local time?

  All about the time, date and in particular time zones for your particular question...

  http://www.7tutorials.com/customize-date-time-and-all-related-settings

• POS 6.1 can choose the correct time zone please?

  Hello.

  IM at the stage of configuration VDP now (...:8543/vdp-configure) and I can't find the good zone time (I need UTC + 7). I use usually Asia/Krasnoyarsk tz, there are a lot of UTC + 7 areas here invalid time zone values and in the SLES itself BUT without these areas at the POS configure the web interface. Can someone tell me why? May be I can complete the configuration with wrong time zone and change later recreating the link/etc/localtime or in the console vm POS? Or should I choose correct time zone during the initial Setup?

  OK, I got a solution. Initial configuration of POS has been completed with the incorrect time zone. Then I changed timzone in the vm console VDP (define-> Asia-> Russia-> Krasnoyarsk time zone), but the bad timzone was still in the POS-configure page. However after the restart of the POS POS-configure vm page indicates the correct time zone (Asia/Krasnoyarsk). Unfortunately, I still can not choose this area to POS - configure-> time zone.

• Every few minutes, the message "the network seems to be down. Is the network configured correctly? »

  When you play Pandora, every few minutes, the message "the network seems to be down. Is the network configured correctly? "is displayed. I click OK and Pandora continues. Network connection diagnostic report no problem. I have the BDP-S390 and a cable network.

  Hello Thomas,.

  Also, try using a different Ethernet cable or try to connect the player to another router's Ethernet port. He may be a problem with the Ethernet cable taking Ethernet to the router/player.

  Make sure that the Internet speed is 2.5 Mbps for SD videos streaming and 10 Mbps for streaming HD videos.

  If my post answered your question, please mark it as an "accepted Solution".

• The FEP Server alert notifications do not display the correct time zone

  Time stamps FEP report

  When I receive my FEP Server alert notifications timestamps are far away. Nobody knows how to set the correct time zone, so the report will be accurate?  I think that the default time is UTC.

  Hello

  If you are referring to serve Advanced Endpoint Protection, I suggest you to report the issue in the link below:

  http://social.technet.Microsoft.com/forums/en/category/forefront

  I hope this helps.

• Failed to install KB2898785. Error, "updates were not correctly configured. Returning from the changes.

  32-bit o/s. Vista Home Premium. All scans/checks indicate no problems

  "Updates were not correctly configured. Restoration of the changes. ....." Advice please?

  M/S Rep told me that the (free) support for Vista is no longer available. Could the problem of security identified in the software of M/S already affected my system (published 12/10/2013 refers)?

  Hello

  I wish that refer you to this article-

  https://support.Microsoft.com/kb/949358/en-us

  Note: Make sure that you get the computer back to the Normal start once you have completed the troubleshooting steps.

  Make sure that you back up the data on the computer before you continue.

  Thank you.

• "The network adapter is not correctly configured to use the ip Protocol" problem on Vista

  Hello. My PC has recently came across this problem "the network adapter is not correctly configured to use the ip Protocol", every time I click on diagnose & repair. I don't know how to fix it. Please help, thanks in advance. Magic

  Hello X-x_MaGiC_x-X,

  Thank you for visiting the website of Microsoft Windows Vista Community.

  Try the rest of the stage in this article:

  System restore points are created automatically when the following occur:

  • When you install a new application or driver.
  • When you uninstall or install some programs.
  • When you install new updates
  • Automatically on a daily interval
  • Manually by creating a.
  • If you choose to use system restore to restore to a previous restore point, System Restore creates a new restore point before you restore a previous state in case something goes wrong. If you are restoring to a previous state in Mode without failure, a restore point will create for the current state.

  So that the restoration of the system to work, you must have 300 MB of free space for each hard disk that monitors the system restore. System Restore will also use up to 15% of disk space on each disk that it monitors. That hard disk space runs out, older restore points will be deleted as newer ones. It is also important to note that you must be logged in as an administrator in order to use the system restore. Now that you understand the basics of the system restore, you must continue to the next section to learn how to use it.

  Restore Windows Vista to a previous state

  In the case of a problem on your computer that cannot be solved by normal means, you can restore your computer to a previous working state. To do this, you need to start restoring the system so that you can choose the restore point to restore. If you currently have Windows Vista boot problems, you can use the system restore in Windows recovery environment. Instructions on how to do it in this tutorial can be found: System Restore using the Windows Vista recovery environment.

  If you can connect to Windows Vista, you must follow these steps.

  1. Close and save any documents that you have opened.
  2. Click the Start button to open your Start Menu. The Start button looks like this:
  3. When the Start Menu open click on the menu option all programs.
  4. Click once on the Start Menu Accessories group.
  5. Click once on the System Tools Start Menu group.
  6. Click once on the icon of the system restore. After you click the icon, if a user account control window opens, click on the button continue.

  You will now be on the screen as shown below in Figure 1 system restore. From this screen, you can specify the restore point that you want to restore.

  1 screen of system restore

  By default, Vista will be already selected the restore recommended option. This restore point is one followed a new pilot program, or update has been installed. If you do not want to use this restore point, you can click on the button next to start the restore process. On the other hand, if there is a more recent restore point that you want to restore you should select choose a different restore point and press the next button. This will bring you to a screen, as shown in Figure 2, which contains a list of all available restore points that you can restore.

  2. the list of available restore points

  You must select the restore point that you want to restore, and then press the button next to start the restore process. Vista will display a window showing your selected restore point and asking you to confirm that it is that you want to restore.

  3. confirm the selected restore point

  If you want to select a different restore point, press the Back button. Otherwise, you can press the Cancel button to exit the system restore or the button finish to begin the restore process. If you have selected finish, Vista will display a second prompt asking you to confirm that you want to continue restoring.

  4. second Confirmation

  If you are sure you want to restore, then press the Yes button. Vista will now log you off the computer and start the system restore process, as shown in Figure 5 below.

  5. restoration of a restore point

  When the restore is complete, your computer will be restarted and when Vista starts it backup will be restored to its previous state. When you open a Vista session for the first time after the restore, you will see a message indicating that the restore was successful.

  6. system restore was successful

  If there are problems with your computer because the last restoration, you can return to your previous settings to ebb in the system restore utility and select Undo system restore by pressing the next button.

  7 undo the last system restore

  Your computer should now work correctly again.

  With the help of the restoration of the system in the Windows recovery environment

  Manual creation of Restore Points

  As mentioned previously, it is also possible to create manual restore depending on points. Some popular designs to create manual restore points are when you have your computer configured perfectly and I would save the State in case of problems in the future. To create a manual restore point, you must follow these steps:

  1. Click the Start button to open your Start Menu. The Start button looks like this:
  2. Click on the control panel menu option.
  3. Click the option menu system and Maintenance.
  4. Click on the system menu option.
  5. Click on the System Protection in the list on the left.

  You will now be at the System Protection tab in the system control panel. This tab allows you to enable and disable the system restore as well as making the new manual restore points.

  8. the System Protection tab

  To create a manual restore point, you must click on the button create. When you press this button a prompt asking you to give a title to this manual restore point.

  9. Enter the manual restore point title

  Type a title for the manual restore point and press the button create. Vista will now create a restore point manually and once finished, post a notice that it was created successfully.

  10. Manual restore point has been created

  Now that you have finished doing the manual restore point, you can close the system window.

  Try to download the correct and up-to-date drivers.

  This should solve your problem.

  Let us know if these steps solve your problem.  I hope the information is useful.

  Kind regards

  Anthony
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• "No access to the network" problem in Windows 7 and error message "your computer seems to be correctly configured but the device or resource (DNS SERVER) is not responding."

  Hello, I have a desktop PC and a laptop (DELL Inspiron N-4050).
  I have problem with my internet connection cable which is working fine on my PC, but does not not on my laptop giving an error "no access to the network.

  When I troubleshoot it says "your computer seems to be correctly configured but the device or resource (DNS SERVER) is not responding."
  I said to many technicians of microsoft online response, but they could not solve my problem and said this is my DNS problem and advised me to contact my Internet service provider. Guess it's because of my internet so why it works on my PC not on laptop?

  Yesterday, my ethernet cable pulled out my cell phone and I couldn't connect to the internet more. But on my desktop PC, it works perfectly fine. (I do not use wifi, if this information is also required) I have studied several threads with similar situations, and I have tried different methods to solve the problem to no avail. I did a system restore, but I'm having no luck. Also, I did not of the latest changes with my anti virus software and my LAN card drivers look to date.

  When I remove my cable from the laptop and again connect my cable then it works but only after the PC sat for awhile.
  1.I did flush DNS by typing "ipconfig/flushdns" in the command prompt.
  2. my IP address, DNS, subnet mask etc are set to automatic.
  3.I also added physical address taken from command line giving "ipconfig/all". for the properties of the network driver settings.
  4.I ' installed the drivers to date of 2014 on my laptop.
  5.I did a lot of searching the web, but they do not solve my problem.

  Please help me to solve it.
  I appreciate your help.
  Thank you.

  Hello Hall,

  Please keep us updated on the status of the issue.

  I suggest you to follow the steps in this Microsoft article troubleshooting and check if it helps:

  Error message "your computer seems to be configured correctly, but the device or resource (DNS server) is not responding" in Windows 7

  http://support.Microsoft.com/kb/2779064/en-us

  Hope the helps of information.

  Please reply with the results, in order to help you solve the problem.

  Thank you

• I have problems with my computer with the time remaining after I reset the clock and made sure it was on the correct time zone and summer time has been check the battery has also been replaced

  and it will not keep the exact time it will keep accelerate at least 5 minutes or more.

  I don't know what else to do about it. You can someone help me?

  I still find myself make too many assumptions.
  First of all, I guess your derivative of clock occurs during the time when the computer is running and not during the period where it is off (or immediately early)?
  Second, I'm assuming that when you run the command "w32tm/Resync" above, the clock made it back to the correct time and no errors were reported?
  Third, you say that your clock drift 5 minutes or more, but you do not tell us how long this gain occurs.  It is two times more win if you wait twice as long to check?  Is the gain gradual or sudden?  Keep he wins or if he stops wins once it arrives before?

  Conditions of default for a computer connected non-member of the field, the time will be updated network-time only at the start and then once a week.  If you are winning too much too quickly, you can adjust how many times your computer asks for time.  Computers in the domain must be more precise and one every hour for a default time synchronization.  You can set your W32tm to that of a computer in the domain to resynchronize your computer more often (SpecialPollInterval).  Here are two articles that describe the clock settings:

  "How to synchronize the time with the time service Windows in Windows XP"
    <>http://support.Microsoft.com/kb/307897 >
  "Time Windows Services tools and settings.
    <>http://TechNet.Microsoft.com/en-us/library/cc773263%28V=WS.10%29.aspx >

  HTH,
  JW

• Rules are configured to my e-mail go to a certain folder, but it is not in the correct folder.

  original title: send rules

  I know exactly how to set up the rules for my email destinations.  Why will they not in the correct folders?

  I come back and check again until the last letter/number shipper address, etc... and they're always in the
  bad record.

  I use Windows Mail.  I can't find any option as shown above.

  This is a screenshot of Vista's Windows Mail message rules. Look in box 2.

  

• Correct configuration of the Cisco Access Point 1242AG

  Hi all

  Here's the situation:

  Recently, we decided to create a small network of WLAN in our company. We choose the Cisco AIR-AP1242AG-E-K9 with 2x2.4GHz 2.2dbi rotating dipole antenna.

  For better management, a new VLAN routable (ID:20) added to our router IP 192.168.55.1 and SNET 255.255.255.0

  Then, I made the following configurations in the autonomous AP through WEB Console:

  • Static IP:192.20.10.35, SNET:255.255.254.0, GWY:192.20.10.200
  • Vlan1 (native) and VLAN20 (Radio0 - 802.11 g) added in Services.
  • I put the encryption against zero for VLAN1 Mode and cipher AES-CCMP for VLAN20
  • In Server Manager, I've defined a new 192.20.10.35 RADIUS server (AP-IP) and a secret shared and left the default ports for authentication and accounting (1645 and 1646). Also, in the default server priorities section I put focused 1 time for authentication EAP and the IP (Radius Server) 192.20.10.35 Access Point MAC.
  • During the General local RADIUS server configuration, I add as a server for access to the network current (AAA client) the same IP address and the shared secret as the ones I use during the configuration of the RADIUS server above. In authentication protocols enable I left checked only the JUMP and the Mac. In addition, in the users individual section 2 new users created with passwords.
  • In the SSID Manager a new hidden SSID created for interface Radio0 - 802.11 g, associated with VLAN20 and in the Client authentication settings section, I left as accepted authentication open with MAC and EAP authentication method. Also, I left the option to use by default for EAP and MAC authentication servers in Server priorities Section and finally I choose mandatory for key management in the section Client authenticated and active the option enable WPA key management.

  I can ping VLAN20 IPs from any PC which is a member of the VLAN native both AP

  As wireless clients, I use 2 Motorola MC5574 with Windows Mobile 6.1 professional. Both of them have a WLAN Jedi adapter that is configured with the following:

  IPs:192.168.55.10 and 192.168.55.11

  SNET:255.255.255.0

  GWY:192.168.55.1

  In addition, a unique profile has been created on all of them to use for the authentication of the association AP. Each profile has been configured for WPA2-Enterprise with AES and LEAP and identification information predefined user (those defined in the PA for individual users)

  The problem:

  Association of clients with AP is always successful but, authentication fails, and I can't ping the AP IP, IP VLAN20, nor the other customers.

  What I'm missing here? I'm sure it's quite simple somenthing but although I tried several different configurations (even WPA - PSK, WPA2-PSK with TKIP) I always find myself without an appropriate solution to unable to ping.

  Thanks in advance for any help

  Hello

  Can you please paste the show run out of AP?

  Kind regards

  Madhuri