The help of two LACP 5448

Similar Questions

• With the help of two different devices for VDR to save the same virtual machines

  Hello

  I have VDR backup right now most of my virtual machines. I'm experimenting with some recovery scenarios disaster using VDR. I want to set up a new device, backup virtual machines themselves, but with a destination off. My question is, it would cause problems to have two different devices, backup the same virtual machines?

  I'm asking this is because I was looking at the notes of recent VMworld session on VDR and he says, regarding a troubleshooting scenario in which you must create a new device in addition to your current device, both devices back up the same virtual machines do not.

  If it is dangerous to do so because of the likelihood that two devices can save the same virtual machines at the same time, I could schedule the backup windows at different times to avoid this problem.

  Anyone have any ideas?

  I create a second local camera vDR and vDR distance and test it against a test VM. The vDR devices will have their own CBT files for each virtual computer, so they should be able to work together, but I would like to go through tests to see how they work well on the WAN. Make sure that you can transfer enough data to host daily data change.

• With the help of two channels of my 6623A

  Hey there, I'm looking for help reguarding a power supply HP 6623 A DC using Labview 9... I'm working on a project where I need to control all 3 channels of power and switch back and fourth to change their output. I tried to change the code in the example, but it will only be 1 channel and clear the other. I can't get the two simultaneously. Thanks for your help

  OK, let's take a step back.

  You control a single instrument.  Therefore, you shoud have only 1 resource that is initialized once and closed once.  You must perform initialization before your loop and close after the loop.

  What I recommend here, is that you use a Structure of the event for the control when you send commands.  The idea here is that you only send orders when your settings change really.  You can use the case of timeout to make the statements.

  And since you claim that you're new, here are some tutorials that you may find useful.

  Introduction of 3 hours
  Introduction of 6 hours
  Bases LabVEW
  Paced self-study for students
  Self Paced Training beginner to advanced, required SSP
  LabVIEW training Wiki
  OR learning
  Getting started with products OR

• With the help of two GPIB-ENET/100 boxes with ibconf - gpib1 selection?

  I hope this is the right forum for this post.

  I'm trying to use ibconf on Solaris to configure a workstation to use 2 boxes GPIB-ENET/100.  I have never tried to configure a computer to use multiple boxes GPIB-ENET/100 at the time, so I don't have a lot of confidence that I'm doing it correctly for two boxes.  Especially given what I describe below.

  According to the manual page 4-2 of the "Getting started with your GPIB-ENET/100 and NOR-488.» 2 for Solaris. "

  To identify your GPIB-ENET/100 in ibconf, perform the following steps:
  1. press on to select the option rename.
  2. type the alias name of host, host name, or IP address assigned to your
  GPIB-ENET/100 and press .
  3. press to exit, chooose to save your changes.

  I followed these steps for both boxes, but the banner at the top of the menu always says 'Card device for Council gpib0' and he always says "gpib0" just to top the host name that I go.  Shouldn't he State gpib0 first Board and gpib1 of the Committee on the second?  But I don't see a way to move to gpib1, or the unit of the second box ("Board") map.  Instead, it seems that I crushed the entrance of host name for the first box, I've identified using the steps above with the host name of the second box, that I've identified by following the steps above.

  I looked through the manual as well as fact a search online, nothing helps.  Which brings me to this forum.

  How should we do to get the pilot configured to use the GPIB-ENET/100 boxes?

  Thanks in advance.  Out of my ibconf is below (that's what it actually looks like, either incidentally - the strange on the line with dev2, dev13, and dev24 is not an artifact of copy/paste):

  ===============================================================================
  National Instruments GPIB Software Configuration utility Rev A.3.
  Copyright (c) 1991 National Instruments Corp.   All rights reserved.
  ===============================================================================

  File: / etc/gpibrc = CAPACITY: 8-plank 44 devices =
  ----------         -----------
  Press a key to continue * -.
  -----------------  -------
  ----------------  ----
  

  -------
  ----

  ===============================================================================
  National Instruments |    Card device for Council SPARCstation gpib0
  ===============================================================================
  -----------
  | GPIB0 |
  ----| nienetD |
  |   |_________|     * Use the cursor keys h, j, k, l & to select a device or a Commission.
  |                   * Use the buttons below to select the desired action.
  =====|------------------=======================================================
  | - 0 dev1 |-dev12 0 1 dev23 2 dev34
  = | - dev2 0 = = |-ev13 = 1 dev24 = 2 = dev35
  | - dev3 0 0 |---4 1 dev25 2 dev36
  | - dev4 0 1 dev15 1 dev26 2 dev37
  | - 0 dev5 1 dev16 1 dev27 2 dev38
  | - 0 dev6 1 dev17 1 dev28 2 dev39
  | - 0 dev7 1 dev18 2 dev29 2 dev40
  |---0 dev8            1 dev19           2 dev30                                                                   2 dev41
  | - 0 1 dev20 dev31 2 dev42 dev9 2 |-0 1 dev21 2 dev32 dev10
  | - 1 dev22 2 dev33 dev4311
  3 dev44
  |

  ^ Q: help ^ r: Rename ^ T: (de) connect ^ edit I: ^ o: output

  I just thought of it. My terminal has been updated with the ansi format. That was streaked the menu and blocks my view of the operating instructions ^ B / ^ F to see maps for more tips. The dockers affecting my vt100 terminal. You can even see how my menu was watered to the top at the bottom of my original message. I didn't know until now that the menu was supposed to look like different (although I knew it).

• With the help of two phone numbers with iOS devices

  Hello

  IM wondering what the compatibility of the eco system is for two different phone numbers linked to two iPhones and how services such as iMessage, FaceTime and continuity will work. Does anyone have experience of this and if it will work? Thank you!

  It will work if you use the same identifier for the iPhone Apple

  iMessage, FaceTime and continuity but not recommended.

• With the help of two CAN channels on cRIO with 9853

  I have a cRIO 9014 controller RT and 9112 chassis and a CAN Module 9853.  I used successfully CAN receive and channel CAN Transmit example projects to check the work of material.  Then, I took two screws FPGAS of each project and grouped in a single FPGA VI by copying just the two in the same VI.  I can correctly transmit and receive with the host live

  My goal now is to be able to use the two CAN channels on the module 9853 for transmitting and receiving CAN Messages on each channel.  I like to use in a project in hybrid Mode later, so I think that there is only a single DMA channel available after that Scan Engine takes 2.  Maybe that's why I get an error when I make a copy of everything in the FPGA VI, make a new FIFO and make copies renowned host of screws with different names of variables to match the copied content from FPGA VI.

  Any other ideas on how to proceed would be appreciated.

  Also, I know that CAN1 needs an external power supply, so it is no more a problem.

  Thank you

  John

  I thought about it, I don't know why, but some parts with part 'FPGA to receive channel CAN' in their own lines fixed.  Now CAN receive is as fast as can be, never drop frames or overflowing the FIFO.  He also compiled FPGA Bitfile 30% faster and was about 50% less use of the device.  Weird...

  If you're curious, here's the new VI:

  

  John

• With the help of two routers to share in may neighbors connection

  Hi, I wonder if anyone can help?

  My neighbors gave me it is code WPA to share it is on the internet and I was picking up using an antenna usb plugged into a portable tops that will share its ethernet connection to router wireless WRT54G linksys so send the signal to my house. Because it means that the laptop must remain in the same place and always be on, I decided to implement my old Wi - Fi tp-link router point in client mode and now pick up the signal on that instead of the antenna usb but when I connect directly to the WRT54G Router I get limited access, are there changes in the settings of the WRT54G to make ethernet direct feeding from the work of tp-link? Any help would be appreciated.

  Thank you.

  Here is an article on how to both routers, http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=785463d9ecaf4cac84aed245b08d615f_3733.xml cascade

• With the help of two programs at the same time

  Hello

  I work with both systems (Mac and Windows). For the moment, I use CS6, but would switch to the CC. My problem is the restriction to work with a system or program at a time. This means that I am not allowed to edit images with photoshop, when I visited a movie that I just edited first, right? Premiere Pro would not be closed because of rendering and so I can't open photoshop? Or After Effects for designing menu while the rendering?

  Thank you again and best wishes,

  Daniela

  Hi Daniela

  You are allowed to two activations for example 2 Macs, 2 Windows or Windows & Mac. You can actually install apps on as many machines as you like a long as two only are activated (sign in)

  But you can start and run applications simultaneously. There is no restriction on that.

• With the help of two GTX Poseiden GPU on a Mobo 99 X 780

  Hello

  I am in the final stages of construction of a PC workstation for creation, still and video image. I have two GTX 780 GPU and they will be installed in/on an ASUS X 99 Deluxe Motherboard. Can someone tell if it is possible to efficiently run two such GPU under first or AE? I guess that for purposes of exposure with the connected monitors and the other for the treatment only?

  If possible, is there software owners out there that would allow me to create this configuration?

  I guess that the SLI would be useless.

  Kind regards

  LJ

  Xferred in Forum Hardware

• With the help of two fonts in a title?

  In first 12 after the opening of a title by default, I want to use two different fonts in the text a Word/title.  12 PE does not seem to allow this.  Is this correct?

  You can use different fonts in a word or a title. You can even use a different font for each letter.

  What you want to do is to make sure that the text layer is active. Then place the ToolTip text beside the police. That you want to change. Click and drag to select the fonts that you want to change. The selection of the new font in the window of FX.

  Best regards, Joe

• License question: with the help of two "Standard Edition" licenses for > 8 vCPU by host

  Hi, I've been reading place on it for a few hours and would like to get confirmation here.  I have

  -a physical host: dual processor, 8 cores per processor

  -multiple licenses VSphere 5.0 Standard edition

  -VCenter 5.0 Enterprise Edition

  I want to distribute the VM with 12 vCPU and I expect to consume two licenses Standard Edition - one for each CPU, for a total of 12 vCPU.  When I try to do using VCenter I get error "virtual machine has 12 virtual processors, but the host only supports 8.»  "The number of virtual processors can be limited by the OS selected for the guest virtual computer or licensing for the host."

  I think that it is a license restriction because on the same host, the VSphere evaluation has authorized the deployment of a 12 virtual machine using RHEL 6.3 vCPU.  I checked later vCPU on evaluation copy function and it was 32 channels for it proves that it is not a BONE or a physical problem.  I think I downloaded an evaluation of the 'norm' rather 'Enterprise', but I am not sure.

  I read compare VMware vSphere editions and the 'Standard' column has CPU line: "CPU 1" and line vCPU: '8 - way '.  This makes me think that, for each new license, I should have a CPU with up to 8 cores.  that is by consuming two licenses, I use 2 CPU and up to 16 cores.

  I also read the EULA VMware multi-core pricing and Licensing Policy , and he said:

  Software licenses with six (6) cores per processor

  It does not say "with hearts of six (6) software licenses by host '

  The following excerpt from the EULA is the only evidence that I could find to support the conclusion that for Standard Edition, the maximum number of vCPU for each host is 8 (regardless of the number of licenses consumed);
  Combines VMware licenses on a single host software. Licensing policy allows combining the even on software licenses uniprocessor.

  Someone can confirm the limitation and is there something obvious that I missed to compare VMware vSphere editions.  The difference between host and per processor is huge, I'm surprised that it is ambiguous.

  Thank you

  Diarmuid

  Looking at this picture, it is said that you need 1 VMware Standard license per physical processor that your host has.  Down the chart to the vCPU, who said that a VM can have at most 8 vCPUs (for Standard).  Isn't 8 vCPUs per license, which is 8 vCPUs total.

  The demo version is licensed Enterprise Plus and develops of vCPU 32 on a virtual machine.

• With the help of two models on a single site.

  Im trying to design a Web site and because of my lack of experience, I went down the road of model. I have download two adobe model muse. I think my website on one of them (so it comes to a site), I want to use the second template as a new page to my site current Web how can I do this?  Thank you. If I have more complicated things, in short how can I use two templates in a site as two distinct pages.

  Hello

  You can configure two different master page, each with a model. See if it works.

  If you are not already aware of the page master, please take a look at this.

  Understanding master pages | Adobe Muse CC tutorials

  Let me know if you have any question.

• With the help of two sheets of different styles in a scene

  I write a tool with which a user can design screens. In the tool, there is a wysiwyg preview area.
  What I want to do: the tool itself must use a certain style (call it 'style sheet tools'). The preview screen should use a different style, which is defined by the application that is presented in preview ("stylesheet for the application").
  
  Is it possible to define the outer part is using 'tool style sheet', the inner part is using 'application style sheet' - so to have two different style sheets, being assigned to different areas of the screen (a field being nested within each other).
  
  Of course...: I could assign special style classes to all the controls in the tool, but it would be much easier for me, if I could avoid this...
  
  I believe very strongly that what I want is not possible: scenes cannot be nested in another, style sheet assignments are made at the level of the stage.
  But: maybe I'm wrong with my assumptions... and there may be a single magic solution...
  
  Thanks for the tips! -also negative adivce ("it is not possible!") is appreciated!

  style sheet assignments are made at the level of the stage.

  This is not necessarily true.

  The CSS reference guide: http://docs.oracle.com/javafx/2/api/javafx/scene/doc-files/cssref.html

  Starting with JavaFX 2.1, the parent class has a property of style sheets, allowing style sheets to be located on a container. This allows a single branch of the graphic scene to have a separate set of styles. Any instance of Parent can have style sheets. A child will have its styles of its own inline styles, stylesheets, of all his ancestors and leaves the scene style.

• EXTRACT DATES WITH THE HELP OF TWO DATES AND THE BOX

  Hello
  
  I HAVE 2 DATE PICKER ITEMS
  : P1_ARRIVAL_DATE AND: P1_DEPARTURE_DATE
  
  AND I HAVE 7 ITEMS in BOXES DAY it return values are 'Y '.
  
  : P1_MON
  : P1_TUE
  : P1_WED
  : P1_THU
  : P1_FRI
  : P1_SAT
  : P1_SUN
  
  as I choose date: P1_ARRIVAL_DATE AND: P1_DEPARTURE_DATE
  AND THE DAY, AS: P1_MON, ONLY THE DATES HAVE TO RETURN WHO HAVE MONDAY AS DAY BETWEEN: P1_ARRIVAL_DATE AND: P1_DEPARTURE_DATE.
  
  
  FOR EXAMPLE IF I CHOOSE THE DATE: P1_ARRIVAL_DATE AS 07_NOV_2011 AND: P1_DEPARTUE_DATE AS: P22_NOV_2011 AND IT HAS 3 MONDAY BETWEEN THESE DATES
  RESULT SHOULD BE DISPLAY AS
  ======================================

   ARRIVAL DATE-------ARRIVAL DATE+6
  ============================
   07_NOV_2011 ---     13_NOV_2011       // THESE ARE MONDAY DATES
  14_NOV_2011 ---     20_NOV_2011     
  21_NOV_2011 --      28_NOV_2011 

  CAN I CHOOSE MORE THAN ONE CHECK BOX AT THE SAME TIME
  FOR EXAMPLE IF I CHOOSE: P1_MON AND: P1_TUE, THE RESULT SHOULD BE
  
  

  ARRIVAL DATE-------ARRIVAL DATE+6
  ============================
   07_NOV_2011 ---     13_NOV_2011   
   08_NOV_2011 ---     14_NOV_2011      
  14_NOV_2011 ---     20_NOV_2011      // MONDAY AND TUESDAY DATES
  15_NOV_2011 ---     21_NOV_2011  
  21_NOV_2011 --      27_NOV_2011
  22_NOV_2011 ---     28_NOV_2011 

  HOW CAN I DO THIS? PLEASE HELP SOLVE THE PROBLEM.
  
  
  
  THANKS and GREETINGS
  CORINE

  X the problem you see is a misunderstanding on my part about what is the date of arrival date of departure... it's inverse reasoning: at your arrival is before departure (and I got it on the other hand, the departure before arrival (:-))

  But there is also a flaw in the code (instead of the Date of arrival by using the select sysdate).

  Please run the code like this:

  with dates as
  (select to_date(:P1_ARRIVAL_DATE,'DD-MON-YYYY')+level-1 as day from dual
   connect by level <= to_date(:P1_DEPARTURE_DATE,'DD-MON-YYYY') - to_date(:P1_ARRIVAL_DATE,'DD-MON-YYYY')  +1
   )
  select day, to_char(day,'Dy') from dates
  where to_char(day,'Dy') = 'Mon' and :P1_MON = 'Y'
  union
  select day, to_char(day,'Dy') from dates
  where to_char(day,'Dy') = 'Tue' and :P1_TUE = 'Y'
  union
  select day, to_char(day,'Dy') from dates
  where to_char(day,'Dy') = 'Wed' and :P1_WED = 'Y'
  union
  select day, to_char(day,'Dy') from dates
  where to_char(day,'Dy') = 'Thu' and :P1_THU = 'Y'
  union
  select day, to_char(day,'Dy') from dates
  where to_char(day,'Dy') = 'Fri' and :P1_FRI = 'Y'
  union
  select day, to_char(day,'Dy') from dates
  where to_char(day,'Dy') = 'Sat' and :P1_SAT = 'Y'
  union
  select day, to_char(day,'Dy') from dates
  where to_char(day,'Dy') = 'Sun' and :P1_SUN = 'Y'
  

  for the period from 01 to 15 November 2011, with P1_TUE and P1_FRI, flag in there, I got this result:

  DAY      TO_CHAR(DAY,'DY')
  11/01/2011     Tue
  11/04/2011     Fri
  11/08/2011     Tue
  11/11/2011     Fri
  11/15/2011     Tue
  

  To simplify (can only test inside the apex report, could not run code in SQL Wkshop):

  with dates as
  (select to_date(:P1_ARRIVAL_DATE,'DD-MON-YYYY')+level-1 as day from dual
   connect by level <= to_date(:P1_DEPARTURE_DATE,'DD-MON-YYYY') - to_date(:P1_ARRIVAL_DATE,'DD-MON-YYYY') +1
   )
  select day, to_char(day,'Dy') from dates
  where v('P1_'||to_char(day,'DY')) = 'Y'
  

  Published by: Kléber M on November 14, 2011 05:06

• With the help of two tables

  As part of my game, I want to have two paintings, a source from the list of words and one holding the clues. What I intend to do, is to randomly generate a Word as well as the idea to this word. I've got the word generator works correctly, but I don't know how I can make a separate table, choose a clue. That's what I have so far as present to the array of words to work:

  Var words: Array = ["LONDON", "CYPRUS", "CHINA"];

  It's my table of words

  number = (Math.floor (Math.random () * 3));

  inProgress = words [number];

  wordLength = inProgress.length;

  
  

  That's what I use to generate the word randomly. Note: the number is a variable number, I created and inProgress is a string variable, that I created.

  I would like to know how I can do randomly generate the index at the same time, using the table:

  var indices: Array = ['Capital of England', 'Small island', more 'high population'];

  If it makes it easier to see all of the code for this I'm going to paste below for you to see. Thank you!

  Var words: Array = ["LONDON", "CYPRUS", "CHINA"];

  var number: number;

  var inProgress: String = new String;

  var wordLength:Number;

  var myDisplay: Array = new Array();

  displayOut var: String = new String;

  var rightCount: number = 0;

  used var: String = new String;

  Guess var: String = new String;

  var guessLetter: String = new String;

  var correctGuess: Boolean = false;

  number = (Math.floor (Math.random () * 3));

  inProgress = words [number];

  currentClue = indices [number];

  wordLength = inProgress.length;

  for (var i = 0; i < wordLength; I ++)

  {

  myDisplay [i] = ' * ';

  displayOut += "" + myDisplay [i]

  }

  var answerText:TextField = new TextField();

  var myFormat:TextFormat = new TextFormat();

  myFormat.font = 'Segoe UI symbol';

  myFormat.color = 0X00FF00;

  myFormat.size = 23;

  addChild (answerText);

  this.answerText.x = 375;

  this.answerText.y = 40;

  this.answerText.width = 250;

  this.answerText.text = displayOut;

  answerText.setTextFormat (myFormat);

  Use a textfield and assign the index as text of this property.

  clueTextField.text = indices [number];