the President is not enough good work sound is very low

Similar Questions

• The President is not working on Equium A100-338

  Dear forum Support from Toshiba,

  I was faced with a problem with my laptop Satellite A100-338.
  I'm not able to use on the enclosure. I tried to play audio / video (CD / DVD) but the President is not functional, no sound!

  If I connect the headphones, I could hear the sound through it.
  Perhaps problemwith aboard the speaker.

  Could help me find any control routine to check if the laptop speaker works or not.
  As a good setting if some / setting needs to be done to make the speaker works

  Please advice!

  > Could help me find any control routine to check if the laptop speaker works or not.

  To be honest, you have already performed a routine check and found that this problem is not related to a faulty audio driver or sound card.
  Due to the fact that your headset is working and you can hear the sound, I guess that your speakers are faulty or the switch inside the headphone jack does not work as it should.

  In both cases, the ASP must be contacted because this is related to the material and only the technician could help you.

  Good luck

• The host has not enough space on the boot partition to store the image upgrade. It takes a minimum of size_in_MB. After the release of space or perform an installation from the CD-ROM.

  Hi everyone, the difficulties in trying to update the Update Manager. ESX4.1 to ESXi5.0

  Error I get is below to correct the scan before update:

  The host has not enough space on the boot partition to store the image upgrade. A minimum of 299MB is necessary. After the release of space or perform an installation from the CD-ROM.

  There is enough space in the local disk

  Size of filesystem used Avail use % mounted on
  / dev/sdd5 4.9 G 1.6 G 3.0 G 35%.
  / dev/sdd2 2.0 G 107 M 1.8 G 6% / var/log
  / dev/CCISS/c0d0p1 99 M 67 M 27 M 72% / Boot
  / dev/CCISS/c0d0p2 4.9 G 1.6 G 3.1 G 34% / esx3-installation
  / dev/CCISS/c0d0p1 99 M 67 M 27 M 72% / esx3-installation/boot
  / dev/CCISS/c0d0p7 2.0 G 101 M 1.8 G 6% / esx3-installation/var/log

  Cannot continue installation due to the lack of space and don't have the option upgrade CD directly (of complicated issues)

  Do you have any suggestions?

  Thank you

  It sounds like this host has already been improved 3.x! In this case you will not be able to upgrade to 5.x using the Manager to update because of the small partition/boot (99 MB).

  to remedy the hosts against a basic upgrade

  ... You cannot use Update Manager to upgrade to 5.0 ESXi host, if the host has upgraded ESX 3.x to ESX 4.x. These hosts have not enough free space in the partition/Boot to support the process of update Update Manager. Use either interactive or scripted upgrade.

  André

• Computer memory virtual is increased from 6 to 8 GB and now vm fails to power on with the error massage not enough resources to meet the HA failover, attached screenshot

  Computer memory virtual is increased from 6 to 8 GB and now vm fails to power on with the error massage not enough resources to meet the HA failover, attached screenshot

  The message is usually due to the Admission HA and reservations control configuration memory set on one or more virtual machines. With the default configuration HA calculates the sizes of slot based on the memory and CPU. Any reserve on a virtual machine could increase the size of the slot and lead to fewer available seats. What you can do is either to reduce (or eliminate) reservations about the VM (s) or set admission control to a percentage rather than the host failures tolerated.

  André

• The volume of the recorded sound is very low when played. I tried to solve the problems through Control Panel of configuration-sound options and increased the volume to 100 form my mic too. All the other volume options, it's 100 too. It has no effect. Hel

  The volume of the recorded sound is very low when played. I tried to solve the problems through Control Panel of configuration-sound options and increased the volume to 100 form my mic too. All the other volume options, it's 100 too. It has no effect. Help needed ASAP

  Hello

  Control Panel - SOUNDS - Audio peripheral devices configuration-manager

  Make sure you write down the description and model double click top - tab drivers - write version. Now
  Click on update drivers who cannot do anything like MS is far behind the certification of drivers. Then RIGHT
  CLICK above and UNINSTALL - REBOOT - this will rebuild the driver stack.

  If your driver shows 06 you have the default windows and part of the question.

  Go to the system manufacturer's website and get the latest Audio/Sound drivers - download - SAVE - go to the place where you
  Put them - right click on Reboot - RUN AS ADMIN -.

  Check the Version on the tab of the driver in the device as a sound Manager often restoring drivers, then install
  the current version. Restart and check after each try, not uncommon to have to run the pilot of 1 to 4 times or more.
  Just make sure that the version you have installed appears in the tab of the driver.

  Then navigate to the site of the manufacturer of the device and search for the drivers more recent and repeat the installation procedure.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  ---------------------------------------------------------

  After the updated driver.

  Click with the right button on the speaker near clock - recorders - right click in the box - check show disconnected devices
  and show disabled devices - check your micro - highlight them, then lower right properties. Do
  of course the appropriate injector is enabled and check that other settings - on the levels tab make sure MUTE is not checked
  and APPLY / OK changes.

  Also in the search for some Audio Manager Panel (perhaps named after the manufacturer of the sound driver). Mine
  is the RealTek Audio Manager, yours can be quite different name if you have one.

  How to activate Audio devices hidden in Vista
  http://www.Vistax64.com/tutorials/143447-audio-device-enable-hidden-devices.html

  Connect one microphone, music player or other audio device to your computer
  http://windowshelp.Microsoft.com/Windows/en-us/help/b0e3d7fb-1b4a-4926-8254-65da289209261033.mspx

  Problems with sound and audio or no sound - a Mr Fixit
  http://support.Microsoft.com/GP/NO_SOUND

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• sound is very low

  His record game

  sound is very low

  Hi mubry_sa,

  ·         What version of the operating system is installed on the computer?

  ·         Did you do changes on the computer before the show?

  ·         You get the error message?

  Follow these methods.

  Method 1: Run the audio troubleshooter.

  Open the troubleshooting of Audio playback

  http://Windows.Microsoft.com/en-us/Windows7/open-the-playing-audio-Troubleshooter

  Method 2: Search the hardware changes. Follow these steps:

  (a) click Start, type Manager of devices in the search box of start and press ENTER.

  (b) right click on sound, video and game controllers, and then click search the hardware changes.

  Method 3: Follow these steps:

  Step 1: Check the status of the speakers and headphones in the playback devices. If it is disabled, enable it. Follow these steps:

  (a) right click on the volume icon in the system tray at the right corner on the desktop.

  (b) select the playback device and activate the speakers and the headphones if it is disabled.

  Step 2: Set speakers as default device and check.

  (a) right click on the volume icon in the system tray at the right corner on the desktop.

  (b) select playback devices, right-click and set as default device speakers.

  Method 4: Follow the steps in the article.

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

  For reference:

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-sound-problems

  Sound cards: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/sound-cards-frequently-asked-questions

• The President will not play

  The President of my g7 Pavilion will not play. It works with headphones or external speakers. A computer repair shop, said that the IDT pilot was missing. The tech guy at the place where I bought the PC said if the pilot was missing or not working is not without audio would play at all even on the helmet. How can I determine if the speakers are inop or simply has not been activated properly etc?

  Thank you

  Hi Allen,.

  Try the following.

  Download IDT Audio Installer on the link below and save it in your downloads folder.

  http://ftp.HP.com/pub/SoftPaq/sp59001-59500/sp59154.exe

  One time finished, open windows control panel, open Device Manager and open sound, video and game controllers.  Right click on the IDT device and select uninstall - also, you should get a command prompt to delete the current driver, check the box allow this and then proceed to uninstall.

  When you are finished, stop the laptop, unplug the AC adapter and then remove the battery.  Press and hold the Power button for 30 seconds.  Reinsert the battery and plug in the AC adapter.

  Robinet tap away at the key esc that you start the computer to launch the Start Menu, and then select f10 to open the bios menu.  Press f5 to load the default values (sometimes it's f9, but the menu below indicates the correct key), use the arrow keys to select 'Yes' and press ENTER.  Press f10 to save the setting and still use the arrow keys to select 'Yes' and press on enter.

  Allow Windows to fully - charge it will automatically load an audio driver, but let just this complete.  Then open your download folder, right-click on the IDT Installer and select "Run as Administrator" to launch the installation.  Once this done, do a right-click the speaker icon in the taskbar and select playback devices.  Left click 'Speakers and headphones' (or speakers/HP) once to highlight and then click the Set Default button - check if you now audio.

  Kind regards

  DP - K

• Error recovery disc on the Satellite A200 - not enough of space

  After reformatting my laptop toshiba recovery disks will not reload windows because it says that I don't have enough space on my hard drive.

  The error message is the following:
  There is not enough space on S3A6134D502. You need extra 2.34 GB to copy these files.
  S3A6134D502
  Free space: 1.42 GB
  Total size: 1.46 GB

  It seems that he has created a new partition which allows to load windows on the partition being too small.

  Problem is that you have modified the standard settings for the recovery procedure.
  First partition on the disk HARD is called WinRE partition and this partition has a capacity of 1.5 GB.
  When you start the recovery procedure and simply click OK or NEXT all went well.

  I guess you have chosen configuration option and click on the second option to install the operating system on an existing partition.

  What you probably want to do is to install the OS on the C partition only in the second hope or all other partitions will not be deleted or formatted. Right?
  I tested several times on P200 and A200.

  It won't work then only option is to erase the whole HARD drive and before recovery installation starts all existing data and partitions will be deleted and formatted.
  So before you begin installation OS Backup all important data and install OS without changing anything.

• How will I know that my Windows product key is if one on the sticker that is located on the computer does not seem to work?

  You want more details. For two hours I answered all the questions that ask you that. And still no support. You up to the date of this laptop, every day at 03:00, so don't tell me the product key, which is on the back of this box is incorrect. Or that it is not the country I say. Just send me what is on the back of this box, which I paid too much for in the first place.

  We are not Microsoft. We are volunteers who give of our spare time to help people. Complain about Microsoft is a waste of time. We are in the same boat as you when it comes to most of the problems and not more control or access that you have to do.

  A product key is not in the box where everyone can see.  It is a sequence of alphanumeric 25 digit of 5 sets of 5 digits separated by dashes for the operating system.  If this is the original installation, the key will be on a label on the underside of the laptop.  It has been upgraded or purchased as a product of the retail (suggested by saying you that you have a box), then the product key for the product to the retail sales would have been on a piece of paper inside the box.  The product key on the label of the laptop would have been crushed (which would have been in the computer would have been product key from the manufacturer that could not be used to enable or provide proof) by installing the retail or upgrade.  Microsoft has no idea what is your product key regardless of the case - even if you bought them (unless it was by a download and then you should have an email from their share with the product key to this topic).

  If this is not a problem of activation or re-installing and that you have installed and activated the product yourself, try of Belarc Advisor http://www.belarc.com/free_download.html and see if the product key, it reveals work best of all what you use now.

  For more information, if it does not help, post to http://answers.microsoft.com/en-us/windows/forum/windows_install?page=1&tab=all&tm=1300700638376.

  Good luck!

• not enough memory in sound recorder

  I recorded several lectures using the sound recorder.  The first two records were successful.  However, when trying to save the third, sound recorder is stagnating and the response on the screen was this sound recorder did not have enough memory.  Is there a way to increase the memory or delete some of the previous records to release the memory for future recordings?

  Sound Recorder cannot use rest memory after you start the system.  Only way to increase this is to add to the computer.

  Are you sure it says memory and no disk space?  If it's the memory, you can restart (to free memory) but not much.  Space of HD IF you can delete files to free up more.

  You can run the HD Cleanup Wizard to remove unnecessary temporary files.

• Sony A55 vs Device Stage via USB, not enough of work

  Sony A55 digital camera (or more correctly the SLT-A55V United States w / GPS) has two modes of operation for its USB connection: PTP and mass storage.  This question is about its use in mode PTP with Device Stage.  Compatibility Center lists the A55, sustained.

  (Device Stage does NOT recognize the device when the mass storage mode value.)  On the other hand, Sony software only works with the USB to the camera in mass storage mode.  This question is NOT on the use of the camera with Sony software.  In fact, the real point of the question is: how best to use this device with Win7 * without * Sony bundled software.)

  Two problems noticed so far, when you use the mode USB PTP of A55 w / Device Stage:

  (1) the "erase after importing" does not work, images remain on the camera independently checked/unchecked (minor annoyance)

  (2) all of the videos on the camera (uses his MP4 format) are not transferred (important deal breaker)

  Device Stage has no such problems with several other cameras that we have (mainly Point & Shoot varieties, for the most part, the Canon), where it clears after import and transfers all media so always correctly or video.   The problematic behavior seems to be unique to the A55.

  The A55 is the latest version of the firmware (2.0), and behavior of Device Stage is unchanged if Sony beam is installed (i.e. the bundle Sony doesn't seem to install anything that creates OR that corrects the problem)

  For example, q: is there something that can be fact/configured for Device Stage (or the A55 himself?) to solve these problems?

  TIA

  Hi davbol.

  You will need to contact Sony support for firmware\driver was last updated for the necessary changes.

  http://www.Sony.net/SonyInfo/support/

• The MaxInteger is not enough

  Hi, I do some mathematical functions in Director and I found that the maximum value that I can put in a variable is 2,147,483,647.

  I need to work with many more. What can I do? There is another way to work with these numbers?

  Thank you.

  You cannot use any higher than integers.  But you can use floats.  Change the number to a float and you should be fine.  If you need for it to have no decimal places, then when display you it on the screen, you can set 'floatPrecision = 0' temporarily so it will look like an integer.  The floatPrecision does not affect the number or all clculations made with him... just the way it is displayed.

• Highlight show boxes in the preview, but not in published work - Captivate 5

  Hello

  I hope someone can help me with what I am quite confused at the moment. I work on a software simulation and work a lot with the highlight boxes. I did at least 3 modules (25-60 slides) with highlighting and have not had a problem until now.  My problem is that I can't get point boxes to appear on the published document. It's only for 1 single slide! All the work left! When I saw in the program the boxes appear and work perfectly, but they do not appear in the published doc. I have reproduced slides and re-recorded this specific slide and nothing works. The theories?

  Help, please!

  Hello

  The picture is not clear, but it seems that the upper heating element is a box configured click to pause the slide to 1.5 seconds? Again, it is hard to see because it's not really clear, but it also appears that your boxes of matches are not configured to show up to about 6 seconds in. So in this case, it would seem that the click box is pause the slide too early. Try adjusting the timing of the click box.

  See you soon... Rick

  Useful and practical links Begin to learn Captivate 5 times now! $29.95 Captivate wish form/Bug report form Certified Adobe Captivate training SorcererStone blog Captivate eBooks

• The sound is very low and Panel beating is not displayed

  Hello

  I reinstalled windows on my Hp envy 15-J028tx 8.1, but the volume is very low, more beat audio Panel does not appear.

  Thanks in advance for the help.

  Hi Muhammad_Hanif,

  Try this downloadWindows 8.1.

  I hope this helps.

  Thank you.

• The surround sound is very low

  I have very low sound, it's tru surround xt

  I have very low sound, I know, it should be higher

  Hello

  ·        What application you use to play music?

  ·        You play a file that is located on the HARD disk (hard drive) or a CD/DVD?

  ·        You play the file on the Internet?

  You can also try the the system volume of choking. To check the system volume follow the steps described in the article below:

  http://Windows.Microsoft.com/en-us/Windows7/adjust-the-sound-level-on-your-computer

  Thank you, and in what concerns:
  Naman R - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.