The Serial HBA Adaptec 1405 + windows 7 + Seagate 1 TB hdd SAS ST1000NM0001

Dear community members

I have the Adaptec card to the subject

-J' updated its BIOS/FW to the latest version
-J' downloaded and installed the latest Adaptec 1405 for Windows 7 x 64 drivers (in my case)

The map itself correctly detects the ST1000NM0001 SAS 1 TB drive (I have a background of basket SAS connected to the HBA, where the HARD drive is gliding/plugged)

Please note that this HBA + cables and so on, perfectly work with a connector SAS 146 GB HARD drive *.

Since the HBA BIOS, I am able to test the ST1000NM0001 and also for formatting (it takes 4 hard hours)

Windows Disk Manager detects the HARD drive

But soon I run the initialization command, disk management is blocked and backplane hdd activity led (one led for each HDD bridge) turns off.

The Adaptec 1405, according to its documentation, supports SAS drives up to 2 TB (especially after that the BIOS updated)

So, what's the problem?

Why can't I initialize and use this ST1000NM0001? Please note that, as said above, he Commander of the Adaptec BIOS, it seems healthy and working properly, no errors are popped when I formatted, nor when I tested it (test and the format are two commands available in the BIOS of the Adaptec HBAS)

For any advice, or even better, thanks for any help.

Robert

P.S. look for ASPI drivers are part of the history, I was already using computers when he was at the time of NT3.51, they say that era ASPI finished with XP, but with such behavior, it seems to me as if he lacked ASPI drivers :-)

Aside from the using snipers badly listed in the other post, I would recommend even when contact Adaptec.

When I had reason to Contact them about problems with another Adaptec card they informed me that for some reason they could solve a few motherboards problems caused with their card

Tags: Windows

Similar Questions

  • Creative Suite 6 Design Standard invalid serial number [unable to use the serial number Mac on Windows]

    I tried to install CS6 Design Standard on my computer, but the installer says that the serial number was not valid. I found the serial number by going to the adobe Web site and navigate to the page with my products. I had installed CS6 about 3 years ago on my old Mac and went to install it on my new PC when I stumbled upon the question. I don't know if I need a different serial number for the PC version or not. How can I install CS6 and why the serial code is not valid?

    Thanks in advance

    I had installed CS6 about 3 years ago on my old Mac and went to install it on my new PC when I stumbled upon the question. I don't know if I need a different serial number for the PC version or not.

    Yes, you do. Serial numbers are Mac only or Windows only. As you have discovered, you can't use a serial number of Mac on Windows (and vice versa).

    You can do a platform Exchange to put the serial number of your Mac and get a serial number of Windows instead.

    Exchange a product Adobe of a different version of the language or platform

  • Get the serial number for Windows 7 after formatting

    I bought Windows 7 online less than a year ago. I need to format my hard drive and before I do, I need to know the serial number to reinstall windows. How can I do?

    Download http://belarc.com/free_download.html Belarc Advisor.  It will give the list of keys for each product that you have installed.

    Good luck.

  • Can I use the serial number of Windows 7 Home Premium to reinstall my system?

    Can I use the serial number of Windows 7 Home Premium to reinstall my system?

    If you mean the license key on the sticker cost of Windows on your computer, then Yes, you should be able to use it to activate the same hotfix version of via a retail disc. You * may * need to use for phone activation method accomplish, however.

    Kind regards.

  • I have a genuine copy of Windows xp professional that I bought, when I enter the serial number it does not enter the letter "N".

    I have re-formatted a computer for my friend, boiught a genuine copy of windows xp pro, but when I have bin and enter the serial number on the last block of numbers it will not enter the letter "N", so I can't validate the copy I have... why?

    I tested the keyboard and the letter "N" works perfectly

    N is a character not allowed in the Windows product key - check the label again.

    Where did you purchase this license?

  • I bought a laptop with a windows xp pro, I have the serial number, but I don't have the installation disc. How can I know which version I need? SP3 has not worked... at the moment I am testing SP1

    I bought a laptop with a windows xp pro, I have the serial number, but I don't have the installation disc. How can I know which version I need? SP3 has not worked... at the moment I am testing SP1

    I bought a laptop with a windows xp pro, I have the serial number, but I don't have the installation disc. How can I know which version I need? SP3 has not worked... at the moment I am testing SP1

    The serial number of the computer has nothing to do with the product key for Windows.

    What happened when you tried to install Xp with sp3? If you do not have the original for the computer that you use to install Windows?

    You can try to contact the manufacturer of the computer who may be able to provide the recovery disc. The disks are usually under $ 20.

  • How can I track down through the serial number of my laptop my Windows license.

    The label containing the serial number on my laptop is fuzzy, and the info available only i've got who can identify this is my Windows Vista license number (which is another label that is still readable). I need my computer S/N in order to request a quote on a power adapter for it. I can't start my computer because the AC adapter cord / CC seems to be broken.

    But back to the question: is there a way to find information on my Windows license, which can be linked to serial number of my laptop?

    Contact the manufacturer of your computer and have them shoot to the top of the order for your PC and they should be able to pull the top of your serial number {I could do with my Dell} - (if you bought through them - maybe it's not possible if you bought the computer at a point of sale where the serial number is not saved unless you have submitted a registration form for) the manufacturer and then it depends on the manufacturer or not they keep this information available and are ready to reveal it to you).  But other than what Malke suggested, it's the only way I know to get the serial number if it rubs off the laptop.

    I'm having a hard time to believe that they need a serial number and cannot identify a compatible adapter of just the name, brand and model (and number).  I'm sure there are other suppliers who can meet your needs without that level of detail.

    Good luck! Lorien - MCSA/MCSE/network + / A +.

  • I had pre installed windows vista on my laptop. now, I replaced the hard drive. so, can we recover only windows giving you the serial number?

    I had pre installed windows vista on my laptop. now, I replaced the hard drive. so, can we recover only windows giving you the serial number? I have sony laptop.

    How to get Vista recovery Media and/or to use the Vista recovery Partition on your computer.

    There is no Vista free download legal available.

    http://eSupport.Sony.com/

    Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

    Normally, they do this for a cost of $ small.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
    A good Vista DVD contains all versions of Vista.
    The product key determines which version of Vista is installed.

    There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

    If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

    Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

    At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

    http://support.Microsoft.com/default.aspx/KB/918884

    MS advice on the conduct of clean install.

    http://www.theeldergeekvista.com/vista_clean_installation.htm

    A tutorial on the use of a clean install

    http://www.winsupersite.com/showcase/winvista_install_03.asp

    Super Guide Windows Vista Installation

    After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

    Mick Murphy - Microsoft partner

  • Problem using the serial port with windows 7

    Hello

    I have a modem of SIM cards (used to update remote controller of the electronic gate) that connects to my computer via the serieal port (COM1).

    The modem comes with its own piece of software that worked fine on my old computer with windows 7 (I had a similar problem, but then I just need to update the driver).

    I now have a new computer and I am unable to connect using the modem (I think I'm using the latest drivers for the serial port).

    Is it possible that I need an older version? If so, how can I get a?

    My motherboard is a GIGABYTE H81M-D2V.

    Any ideas?

    Thank you

    AVI

    Hi Avi,

    Thank you for the update on the issue.

    The UART, or Universal Asynchronous Receiver / Transmitter, is a characteristic of your microcontroller useful to connect serial data (text, numbers, etc.) to your PC. The unit switches incoming parallel information (in the microcontroller/PC) to series data that can be sent over a communication line.

    According to the description you provided it seems that your modem isn't connecting with your Windows 7 computer, then I would contact Duetech Berès your modem manufacturer, so that they provide you with the steps to set it up.

    Get back to us after contacting them and please get back to us with your question was last updated.

    Kind regards.

  • Reinstall Windows 7 after adding RAM does not work, if the serial number on the hard drive doesn't go to Microsoft?

    The serial number of the hard drive go to microsoft, I went to reintall my windows after it kept crashing, updated my hard drive, memory, ram.  I think because the serial number is different on the hard drive, it will not be installed.

    System becomes inadmissible has nothing to do with the product activation.

    The probable cause is faulty RAM or loose, make sure that the memory modules are firmly fixed and mounted in banks of memory on the motherboard.

  • CS2 does not work on Windows 10 that I entered the serial number provided, but I get an error

    I entered the serial number provided on the CS2 activation set up the link. He said that there is an error. Acrobat 7 does not work on windows 10

    Hello

    Yes, Acrobat 7 is not compatible with Windows 10. It may or may not work on Windows 10.

    .

    Thank you!

    Shivam

  • Can't reinstall Acrobat 8 to 10 of Windows; It indicates the serial number is not valid.  Please notify.

    Hard drive crashed and I'm trying to re - install Acrobat 8 to 10 Windows.  Found the serial number of the email of purchase and the product to the user account information.  During installation, it does not recognize the serial number I have provided as it says it is invalid.  Please notify.

    Hello

    Acrobat 8.0 is not compatible with Windows 10.

    To install Adobe Acrobat Pro 8.0, your Windows system must be running Microsoft Windows 2000 with Service Pack 4; Windows Server 2003 (64-bit or 32-bit editions) with Service Pack 1; Windows XP Professional, Home, Tablet PC, or editions x 64 with Service Pack 2 or Windows Vista Home Basic, Home Premium, Ultimate, Business, or Enterprise (32-bit editions or 64-bit). You must have Microsoft Internet Explorer 6 or 7 is installed.

    I hope this helps!

  • I bought Adobe Lightroom 6 only to see my DVD drive does not work with Windows 10.  Is it possible to download Lightroom?  I have the DVD with the serial number.

    I bought Adobe Lightroom 6 only to see my DVD drive does not work with Windows 10.  Is it possible to download Lightroom?  I have the DVD with the serial number.

    Download and install the trial version of Lightdroom CC.

    Then enter your serial number, follow these steps

    How to convert a trial CC 6 Lightroom Lightroom

  • How can I install Adobe Acrobat DC Windows XP? Can I download and install Adobe Acrobat XI Pro and then use the serial number of DC for the record?

    How can I install Adobe Acrobat DC Windows XP? Can I download and install Adobe Acrobat XI Pro and then use the serial number of DC for the record?

    Hi ckc60777449,

    We're sorry, but the serial number would work only for Acrobat DC and not acrobat XI.

    You will need to upgrade your operating system to windows 7 to install acrobat DC.

    Let us know if you need additional assistance.

    Concerning

    Sarojini

  • I have Adobe Creative Suite 6 Design Standard in the Windows Version, how do I get the serial number for a MAC Version?

    Hello

    I have Adobe Creative Suite 6 Design Standard in the Windows Version, how do I get the serial number for a MAC Version?


    I downloaded Adobe Creative Suite 6 in my Mac, but it does not accept the serial number.

    What should I do?

    Thanks for any help.

    Best regards


    Digga515

    Product change or the language platform - they might still be offering this for CS6, although it gets old...

    You can exchange languages/platforms for a newer version product if you follow the instructions on the following link:

    l http://helpx.adobe.com/x-productkb/Policy-Pricing/Order-Product-Platform-Language-swap.htm

    You can exchange only once and lose the Windows license, when you switch to the Mac

Maybe you are looking for