The specified picture is an unknown type is invalid. Select a different picture

Similar Questions

• In XP, when you try to install the printer, get error "the specified port is unknown."

  See the title of the question.

  * original title - when I try to install the printer, I get the message "the specified port is unknown. This happened after cable tv and cable modem has been installed

  Thanks for your help. I am not a comp read and write to do all this.  here goes

  No printer listed. I deleted all.no ports usbxxx or dot4xxx. several others listed.

  Middle neck is the same. Intel

  the RT is Windows 2000 or xp.

  It's what I expected.

  Usbprint.sys figure 54 times more often in documents and settings. also in nt service pack driver PK. Ditto for usbmon.dll.

  This is not the case.

  1. open Windows Explorer and type C:\Windows\system32 into the address bar.
  2. find usbmon.dll
  3. right click on this file. Select properties, and then click the Version tab. Is - this version 5.1.2600.5512?  If not, is what version?
  4. now, go to the C:\Windows\system32\drivers folder
  5. what version is the usbprint.sys file?

  You have a copy of each file in C:\Windows\ServicePackFiles\i386?  If so, what are the versions of these files?

  If the usbprint.sys and usbmon.dll in C:\Windows\ServicePackFiles\i386 files are identical (or older) versions that the corresponding files in C:\Windows\system32 and C:\Windows\system32\drivers, copy the C:\Windows\ServicePackFiles\i386 files into their appropriate folders.  Then restart.

• We get 0 x 00000704 error. "The specified port is unknown" during the installation of the printer software.

  Original title: error 0x800f0243

  I tried to install the software for my 9130cw mfc via a wireless connection and I got this error, followed by an error of 0 x 00000704.  "The specified port is unknown."

  Ive had no problem installing the rest of the printer on my other laptop... but now its giving me a problem on these new.  Any help is welcome

  Hello

  Please write to us.

  The question you are faced to could be due to incorrect settings of the printer.

  To better understand the issue, I want to know:

  1. What is the brand and model of your computer?
  2. Have you installed the printer software on the other computer via the wireless connection/USB port?

  Please, try the following steps and check if that helps.

  1. Press the Windows key + R key, type control, and then click Ok.
  2. In all the elements of the Control Panel, click on devices and printers.
  3. Then double click on Add a printer , and then choose Add a network, wireless or Brother MFC 9130cw printer.

  Feel free to write us again if you have other queries, comments or suggestions using your Windows.

• Cannot find the specified dynamic type VirtualEthernetCardDistributedVirtualPortBackingInfo

  Hi all

  I send the SOAP message to vcenter (business listing API 5.0 Vsphere)

  just to change portgroup on vNIC. change portgroup on vDS

  but I get an error

  Table
  (
  [faultcode] = > ServerFaultCode
  [faultstring] = >
  Cannot find the specified dynamic type VirtualEthernetCardDistributedVirtualPortBackingInfo

  during the DataObject analysis serialized type vim.vm.device.VirtualDevice.BackingInfo
  on line 36, column 5

  When parsing 'storage' of the statics of the property, type VirtualDeviceBackingInfo

  during the DataObject analysis serialized type vim.vm.device.VirtualE1000
  on line 27, column 12

  in the "peripheral" static property analysis, type VirtualDevice

  during the DataObject analysis serialized type vim.vm.device.VirtualDeviceSpec
  line 24, column 10

  during the "deviceChange" of static property analysis, type ArrayOfVirtualDeviceConfigSpec

  during the DataObject analysis serialized type vim.vm.ConfigSpec
  on line 18, column 8

  during the "config" static property analysis, type VirtualMachineConfigSpec

  during the DataObject analysis serialized type vim.vm.CloneSpec
  in line 8, column 6

  during the analysis of the CloneVM_Task method call information
  on line 4, column 4

  during the analysis of body SOAP
  on line 3, column 2

  When parsing of SOAP envelope
  on line 1, column 0

  When parsing the HTTP request for clone method
  object of type vim. VirtualMachine
  on line 1, column 0
  [detail] = > Array
  (
  [InvalidRequestFault] = >
  )

  )

  I want to ask what I have wrong or there is a problem with the API

  pls message SOPA and help me.

  Thank you very much

  Also, here is an article on the SOAPAction values:

  http://KB.VMware.com/kb/1033447

• The MCSTRM service failed to start due to the following error: the system cannot find the specified file

  My computer starts rather suddenly gel with many applications.  Today it froze again once I finished a long email and was about to send.  I lost him of course.  My Event Viewer was the topic.  Event 7000, Service Control manager Eventlog.

  What can I do?  I have Vista SP2 64-bit.

  I'll add that the kernel_driver of Type 1 mcstrm following 1 State arrested Win32_exit_code 2 <0X2>Wait_hint Checkpoint 0 x 0 0 x 0

  Please... any help to fix... my computer keeps freezing. and I will need to get a new laptop or an Ipad, if the problem persists.

  Thank you

  Candy C:\Users\David> net helpmsg 2

  The system cannot find the specified file.

  Is that error on this post code, IE something deleted, probably your antivirus or you.

  For problems to explore, which has nothing to do with this post, try this (which covers almost any problem).

  Explorer

  Explorer (explorer.exe) is the program that is the start menu and taskbar, windows folder and the office (which is a folder window).

   

  To see if a fix is available

  In Control Panel (and select Classic discovered in the left pane) select reports on the problems and Solutions (problem of type in the START search box), go to historical problem, right-click of your error and choose check for the Solution.

  You can also right-click and choose Details for more information. Post these details here. The name of the Module fault is important information.

  If the problem affects Panel press the Windows key + R and type wercon (or type it at a command prompt).

   

  Close the browser and start a command prompt

  • Close Windows Explorer
  • Start - All Programs - Accessories - right on command prompt and choose run as administrator.
  • Click Start. Ctrl + Shift + Right-click on an empty spot (just above the power of buttons is one place) then Exit Explorer.
  • Press Ctrl + Alt + Delete then Task Manager.
  • Control all processes to explore are closed. On the process tab select explore and right-click and choose end process, repeat if more of an Explorer in the list.

  Then to restart the Explorer after trying all of the following

  • Press Ctrl + Alt + Delete and choose Task Manager
  • In the Task Manager, click the file menu and then click new task (run) and enter explorer

   

  If you cannot start the Explorer at all

  • Press Ctrl + Alt + Delete and choose Task Manager
  • Under the processes tab, click Show processes from all users to elevate to administrator
  • In the Task Manager, click the file menu and then click new task (run) and type cmd
  • Other things you can try typing
    

    Explorer
    Explorer c:\
    Explorer/e, c:\
    wercon
    control
    Iexplore
    Rstrui

  If you cannot start a folder window you can use the Browse button in the new task dialog. Don't forget that you must right click and choose Open rather than double-clicking.

   

  Reregister the shell registry entries

  It is important that each order is accepted. If the command fails it means the file is damaged and must be repaired.

  Close the Explorer like above and then type at the command prompt (or copy and paste by clicking in the command prompt window and choose Paste).

  regsvr32 /i shell32
  regsvr32 /i urlmon.dll
  regsvr32 RPCRT4.dll
  regsvr32 PROPSYS.dll
  regsvr32 MSCTF.dll
  regsvr32 cscui.dll
  regsvr32 rsaenh.dll
  regsvr32 timedate.cpl
  regsvr32 ATL DLL
  regsvr32 OLEACC.dll
  regsvr32 actxprxy.dll
  regsvr32 USERENV.dll
  regsvr32 msshsq.dll
  regsvr32 NaturalLanguage6.dll
  regsvr32 thumbcache.dll
  regsvr32 WINTRUST.dll
  regsvr32 MMDevAPI.DLL
  regsvr32 audioses.dll
  regsvr32 audioeng.dll
  regsvr32 ExplorerFrame.dll

  
  regsvr32 msi.dll
  regsvr32 FirewallAPI.dll
  regsvr32 netshell.dll
  regsvr32 pnidui.dll
  regsvr32 QUtil.dll
  regsvr32 c:\windows\system32\wpdshserviceobj.dll
  regsvr32 WINHTTP.dll
  regsvr32 C:\windows\system32\qagent.dll
  regsvr32 C:\windows\system32\portabledeviceapi.dll
  regsvr32 wbemprox.dll
  regsvr32 wbemsvc.dll
  regsvr32 fastprox.dll
  regsvr32 imapi2.dll
  regsvr32 wshext.dll
  regsvr32 gameux.dll
  regsvr32 msxml6.dll
  regsvr32 vbscript.dll
  regsvr32 jscript.dll
  regsvr32 wshext.dll
  regsvr32 wshom.ocx
  regsvr32 wshcon.dll
  regsvr32 scrrun.dll
   

  Delete the folder and the settings of the Menu

  This will remove the settings are saved for each file that you visit. Also the order of the start menu and pinned list settings.

  Close the Explorer like above and then type at the command prompt (or copy and paste by clicking in the command prompt window and choose Paste).

  Reg delete "HKCU\Software\Classes\Local Settings\Software\Microsoft\Windows\Shell" /f

  Reg delete "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Streams" /f

  Reg delete "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\StuckRects2" /f

  Reg delete "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\StartPage" /f

  Reg delete "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\MenuOrder" /f

  Delete the thumbnail and icon Caches

  Close the Explorer like above and then type at the command prompt (or copy and paste by clicking in the command prompt window and choose Paste).

  attrib - r s h '% userprofile%\AppData\Local\*.db '.

  attrib - r s h '% userprofile%\AppData\Local\Microsoft\Windows\Explorer\*.db '.

  del "% userprofile%\AppData\Local\*.db".

  del "% userprofile%\AppData\Local\Microsoft\Windows\Explorer\*.db".

  Disable thumbnails and previews

  Damaged documents and particularly corrupt pictures or videos, can cause Explorer crash all trying to generate a thumbnail or an overview. This miniature and previews active option off.

  If you can start the Explorer, previews is Union on the command - folder and Search Options - framework of tasks use classic Windows foldersbar.

  Thumbnails are organized on the command bar - folder and Search Options - view tab - and check under Advanced settings - always show icons, never thumbnails and uncheck Show icon file in the pictures.

  If you cannot start the Explorer close Explorer as above and then type at the command prompt (or copy and paste by clicking in the command prompt window and choose Paste).

  Tracking Add "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced" v "IconsOnly" /t Reg_DWord /d 00000001 f

  Tracking Add "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced" v "ShowPreviewHandlers" /t Reg_DWord /d 00000000 f

  Tracking Add "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced" v "ShowTypeOverlay" /t Reg_DWord /d 00000000 f

  Turn around after testing the Explorer.

  Tracking Add "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced" v "IconsOnly" /t Reg_DWord /d 00000000 f

  Tracking Add "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced" v "ShowPreviewHandlers" /t Reg_DWord /d 00000001 f

  Tracking Add "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced" v "ShowTypeOverlay" /t Reg_DWord /d 00000001 f

   

  A boot is a way to explore

  It can be caused by a shell extension.

  Explorer (explorer.exe) is the program that is the start menu and taskbar, windows folder and the office (which is a folder window).

  The Explorer is built on addin programs called Extensions of Shell. The standard is provided by Microsoft, but programs add their own.

  • Download Autoruns http://technet.microsoft.com/en-us/sysinternals/bb963902.aspx
  • Close Windows Explorer
  • Start Autoruns by right-clicking and choose run as administrator
  • Click on the menu Options - Filter Options and check hide Microsoft entries and disable include empty locations
  • Go to the Explorer tab and uncheck everything to the left.
  • Click Start. Ctrl + Shift + Right-click on an empty spot (just above the power of buttons is one place) then Exit Explorer.
  • Press Ctrl + Alt + Delete and choose Task Manager.  Control all processes to explore are closed. On the process tab select explore and right-click and choose end process, repeat if more of an Explorer in the list.
  • Click the file menu and then click new task (run) and enter explorer

  If this can help, reactivate ½ at a time to identify those who. If this does not help, restart AutoRuns and go to the all tab and uncheck everything that it and restart. If this can help, reactivate ½ at a time to identify those who.

  Run Microsoft Fixit

  Microsoft has a range of automatic programs to solve common problems. To see problems explore

  http://support.Microsoft.com/mats/windows_file_and_folder_diag/en-us

  For the visit of the list the most comprehensive

  http://support.Microsoft.com/FixIt/en-us

  When you choose to download, choose the option to run on another computer. You can then save it to your hard drive. Open the folder, open the folder fix this laptop and run Run Fix It. It will contain all 27 FixIt.

  Recycle Bin
   
  If the problem is the trash bin remove the storage folders. It will be automatically re-created next time you delete a file or open the Recycle Bin. It will remove the trash and the files it contains for all users.
   
  Close the Explorer like above and then type at the command prompt (or copy and paste by clicking in the command prompt window and choose Paste).
   

  RD C:\$RECYCLE. BIN/s/q

   
  then repeat for each drive to change the drive letter, for example
   

  d:\$recycle Rd. BIN/s/q

   

  e:\$recycle Rd. BIN/s/q

   
   
  If the Office does not start
   
  This will create a new empty by user and common desktop computer. This will allow to test if a file on your desktop to start the Explorer.
   
  Close the Explorer like above and then type at the command prompt (or copy and paste by clicking in the command prompt window and choose Paste).
   

  MD "% userprofile%\DesktopTest".

   

  Add reg "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\User Shell Folders" / v/t desktop REG_EXPAND_SZ /d "% USERPROFILE%\DesktopTest" /f

   

  MD "% public%\desktopTest".

   

  Tracking Add "HKLM\Software\Microsoft\Windows\CurrentVersion\Explorer\User Shell Folders" v "Common Desktop" REG_EXPAND_SZ /d "% Public%\DesktopTest" t f

   
  To restore default after having tested if begins to explore.
   

  Set ExpFix1 = % user

   

  Set ExpFix2 = % profile

   

  reg add "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\User Shell Folders" / v/t desktop REG_EXPAND_SZ /d "% ". ' ExpFix1 ExpFix2%% \Desktop "/f

   

  Set ExpFix1 = % Pub

   

  Set ExpFix2 = % lic

   
  reg add "HKLM\Software\Microsoft\Windows\CurrentVersion\Explorer\User Shell Folders" /v "Common Desktop" /t REG_EXPAND_SZ /d "% ". ' ExpFix1 ExpFix2%% \Desktop "/f
   
  You will need to disconnect then.
   
   

  New entry missing folder

   

  If the above does not help.

   

  Download NewFolder.reg from https://skydrive.live.com/redir?resid=E2F0CE17A268A4FA 121.

   

  Click Start - All Programs - Accessories - right on command prompt and choose run as administrator. Type Regedit menu and file - import , import the NewFolder.reg.
    

• Restore failed image because of the message error "system cannot find the specified file (0 x 80070002). Is my file of the backup OK folder structure?

  I had to reinstall clean Windows 7 64-bit because of the failure of the RAID 1. I have a picture of my original installation system, but I can't restore it; everything I try, I get the message "system cannot find the specified file (0 x 80070002).  I work through a number of possible solutions, without success so far.

  According to the kb/951002 (that is for Vista but I can't find an alternative for Win 7) I made sure that the SYSTEM account has read permission for the backup folders and subfolders.  However, the file structure of the specified in the above article backup folder is different from my image file structure.  Specifically, article specified a structure of 'N.zip' file for the backup files but mine are a mixture of XML documents and VHD - i.e. no "zip" files Also, my GlobalCatalog file does not what kind of file, for example, it wouldn't ".wbcat" required file type specified in the article.

  The differences above could explain the inability to restore the image and if so, any ideas on what to do about it?

  Kind regards

  Ian

  Thanks Mick, will redirect the request.

  Kind regards

  Ian

• Setup error "the system cannot find the specified file" (hpzprl40.exe)

  Trying to install HP Photosmart c5180 all-in-one using the latest version of the software download at HP and have Windows 7 Asus desktop computer. Receive error install "the system cannot find the specified file" (hpzprl40.exe), and the wizard stops.  Help, please.

  Hi loveisus,

  Try using the brush included in the CD or download. Let me know what you find?

  Of the Original installation CD:

  1. Insert the CD in the drive and then cancel Setup

  2. open my computer and click right then on the CD from the drive and select open

  3 open the Util folder

  4 open the CCC folder

  5. run the uninstall_L4 (exe or Bat)

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  9 download drivers and full software features

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=MP-76232-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 1153481 & sw_lang=.

  10. run the download to reinstall the printer

  If the software has been downloaded and extracted to your system:

  1. type % temp % in the field of race

  2. Locate and open the folder starting with 7z (example: 7zS2356)

  3 open the Util folder

  4 open the CCC folder

  5. run the uninstall_L4 (exe or Bat)

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  9 download drivers and full software features

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=MP-76232-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 1153481 & sw_lang=.

  10. run the download to reinstall the printer

• Superposition of the images on the specified point

  Hello!

  I have 2 pictures with a lot of similarities. I want to layer them on a specified point or edge or a unique feature. Is it possible to choose a point (by hand or by an algorithm) and then find the corresponding (or similar) on the other image? and then superimpose the images according to the corresponding point? Algorithm of the overlay is made, now I need to find matches between the two pictures and then you cover them according to the similarity.

  Thank you!

  gbbalint

  Hello

  I modified the labview example. Run it, input two images (left, right), then "load", select the edge KING (see image below) and "search". Then superimpose one image over another with transparent ('overlay'). The code is a bit messy, but you can clean for your project.

  

  You said that the superposition algorithm is done, could you please share it? Maybe your solution is more sophisticated and can help me with another project.

  I hope this helps you.

  Best regards

  K

• How to get the parameter values of a step type custom when I create file and adding a type of step seq

  I use lv 8.5 and teststand 4.0.

  I did a step type custom and recorded at the MyTypes.ini in pallets of type.

  I specified a default module by opening the properties of the custom step of *.ini type window, then I put some values of the parameters.

  T1) when I open teststand and I add the custom step type manaully in seq file, the labview module parameter values are represented.

  But, if to use file (create and add support prototype stage), the labview module parameter values has the default value.

  Using joint file, how to get the setting custom step type values I put in *.ini?

  Q2) each type of step are automatically by name through the use of LoadTypePaletteFilesEx. When I open teststand and I add the custom step type manaully in seq file, the module is loaded automatically. Inside the attachment, I use a prototype of charge and a fixed path where the module labview is to load the labview module.

  Can I load module automatically without using a prototype of charge or how can I get a dynamic path of type step?

  I solved Q1 for myself by using the mapping tab of the parameter within the configuration to the default module window.

  Everyone knows Q2?

  Thank you.

• Windows cannot connect to the printer. The name of the printer has been correctly entered, or the specified printer has lost its connection to the server.

  A Windows Server 2003 Standard Edition SP2 32-bit computer is a field, the file and print server.

  A computer on the domain is a machine of Windows 7 Ultimate 64 - bit with HP DesignJet 500 24 printer connected via USB.  The printer is running the latest firmware.  The PC is running the latest 64-bit drivers with no problems to the host machine printing.  The host also has the latest drivers 32-bit (x 86) installed by downloading by other computers on the network.  The printer is configured to share with the share name of HPDJ500.

  Now, on a machine Windows XP Pro SP3 32 bit on the field, I'm trying to connect to the shared printer.  Add a printer > click Next in the wizard of > check "a network printer or a printer attached to another computer" and then click Next > click on "Find a printer in the directory", then click Next > click Find now > HPDJ500 in the list below (the XP machine can see the shared printer on the Windows 7 computer!) and click OK.  At this point, I get an error that says: "Windows cannot connect to the printer.  The name of the printer has been correctly entered, or the specified printer has lost its connection to the server.  For more information, click Help. »

  Alternatively, if I right-click on the HPDJ500 printer listed, then click on connect, I get the same error message but I also see a separate window that says "Connecting to HPDJ500 on H2.ws.net" with the lively projector.  This window also disappears as soon as I clear the error message.

  Please note that this printer worked perfectly as a printer shared, hosted on a machine XP 32 bit on the field.  It works perfectly for the new Windows 7 64-bit machine, but we cannot connect from anywhere else on the network (including the server which translates the same exact error message).  On the server, I also preinstalled drivers thinking there was a problem with a 32-bit computer, trying to grasp the correct drivers from the host 64-bit Windows 7, but that doesn't change anything.

  How connect to this printer?

  Try using the path UNC path of the printer in the Add Printer Wizard.

  Add a printer > network printer > connection to this printer ((deuxieme point)

  Click next to browse (leave blank, the name field) or type the UNC path of the printer (i.e. \\Computername\Printername) path

• Impossible to delete the "cannot find the specified file. Be sure to only specify the path and the correct name?

  For sum reason my computer just started to do the following when I try and delete a file or move a file from one place to the other.

  I am the administrator and the file is there.

  Failed to remove "" cannot find the specified file. Be sure to only specify the path name and filre coeerct.

  Help!

  Perry

  Hi KAD Rebar,.

  1. Did you the latest changes on the computer?
  2. When was the last time it was working fine?
  3. Are you having similar problem with all the files you are trying to move or remove it from the computer?
  4. You have security software installed on the computer?

  Method 1

  See the link below and run the Fixit tool available, check if it helps.

  Diagnose and repair Windows files and folders problems automatically

  http://support.Microsoft.com/mats/windows_file_and_folder_diag/

   

  Method 2

  If the previous step fails, then I suggest that you start the computer in safe mode and check if the problem persists.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  If the problem does not persist in safe mode, then it is possible that some third-party programs installed on the computer is causing the problem.

  I suggest that you put the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

• Error 2: The system cannot find the specified file

  Failed to start the Windows Audio service on the local computer. Error 2: The system cannot find the specified file.

  Help, please
  Sam

  What version of Windows, including service pack (right click on my computer > properties)

  What past just before the problem arises?

  Click Start > run > services.msc > OK
  Scroll down to "Windows Audio"

  The Windows Audio service must be started and its "Startup type" should be "automatic".  If it is not started, double-click the entry and click on the Start button.  If it is unable to start the service or instead generates an error message, the file for the Audio Service may have become corrupt or deleted (although this file has to be protected by Windows File Protection).

  Search for your system (probably C :) drive
          
  audiosrv. DL (it's only one L)

  Make sure to look in the "system folders" "hidden files and folders," and "subfolders.

  You should find the audiosrv.dll (with two Ls) in C:\Windows\system32.

  If she is not there, it should be in C:\Windows\ServicePackFiles\i386

  If it's not there either, you have a file named audiosrv.dl_ in C:\i386?

• How can I change the color of ground on a type of dynamic data graphic waveform?

  I have several different plots on different graphics, and I want to set the colors different waveforms.

  To view the waveforms on different graphs, I went to the dynamic and then divided data type wire

  According to the number of channels I have.

  I can set the background color of the chart with a property node and create sliders of different colors without problem

  using the table of references that I created, so there's nothing wrong with my table of references or the property node.

  As soon as I try and a box of thread in the plot color > control color to draw, I get error 1055 on the property node.

  I was wondering if it was an error between keyboard and Chair, but now I think it's something more sinister.

  The error box appears and cannot be fired left the update until I run TASKKILL on LabVIEW and terminate.

  Any ideas on how to achieve my goal would be appreciated.

  (LabVIEW 8.6)

  My colleague has just acknowledged my problem and pointed me to the solution. It seems I need wiring in the value of "active conspiracy" of the loop each time and to ensure that this takes place before the update to track color.

  I have attached a picture of a labour code. I intend to combine the whole lot to the node of a property with the active plot at the top so that it executes first.

  Thank you for taking an interest Sheela

• DAQmxErrChk gives problem (the specified resource is reserved)

  Hello

  I'm new to programming. I have a four channel USB DAQ. I use CVI to program the channels. One of the channels gives a simple output of a voltage signal while the other generates a square wave. I used the example programs for my code. I use the Volt update for the first string and the Cont Gen Volt Wfm - Int Clk example for the second case. When I run the program it compiles without error and runs. But when I start the generation of any type of wave for the second string and try to change the output voltage for the first channel, the program gives an error and stops at

  DAQmxErrChk (DAQmxStartTask (taskHandle));

  in the example of update of volt.

  The strange thing is that when I'm not generating any output for the second channel it gives no error when I change the voltage to the first string.

  Please please tell me what is the problem

  The error that is displayed indicates that

  The specified resource is reserved. The operation could not be performed as indicated.

  Name of the task: task _unnamed<3>

  Ststus Code:-50103

  lahorimunda,

  Please post on the Forums of NOR. If I understand correctly you are two different programs to run different channels? If this is the case you run through what we call that a reserved resource error is because you are allowed to have only one task of analog input running simultaneously. You will need to put all the channels within the same task, this will prevent you from running through the reserved resource error. I hope this helps.

• error starting "C:\Document and Setting\user_name\Application Data\wlaplg.dll the specified module cannot be found"

  Original title: error loading of C:\Document and Setting\user_name\Application Data\wlaplg.dll the specified module could not be found

  For two or three weeks there whenever I boot my netbook and connect to my user account window I found this error message RUNDLL pop-up window:

  Error loading of C:\Document and Setting\myusername\Application Data\wlaplg.dll

  The specified module could not be found

  What is the problem? and how to solve?

  Hello

  Click on Start menu and click Run.
  Inside run, type MSCONFIG and press Ok.
  Now, you will get a System Configuration window.
  Inside you go to the tab called start-up
  In the Startup tab, you can see a list of files from loading when you start the computer.

  There, you can see the above file Rundll32, "C:\Document and Setting\user_name\Application Data\wlaplg.dll ' like this.

  A chech this one and press apply and press Ok.
  Now you will be asked to restart the computer.

  The problem will be solved after restarting...