time base machine info

Similar Questions

• the operating system XP SP3(base machine) deployed vm workstation with red hat linux image n/w connection problem

  HI, this is my first post on any of the communities...

  I stuck with a problem, on my windows machine, I deployed vm pre-installed with linux Redhat kernel image, it is that of my linux (vm), I can not ping the default gateway, I can ping the ip address of my base machine, nor I can ping vmnet1 and vmnet8. I use VM for the first time, stuck at this point for about a week, some body please help...

  Here is that my machine base and retail ip vm configuration, please check why I am not able to connect to the VM (linux) site to the basic machine.

  Thanks in advance,

  out put of ipconfig/all: -.

  Ethernet VMware Network adapter adapt VMnet8:

  The connection-specific DNS suffix. :

  ... Description: Eth virtual VMware

  DHCP active...: No.

  ... The IP address: 192.168.119.1

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. :

  Ethernet VMware Network adapter adapt VMnet1:

  The connection-specific DNS suffix. :

  ... Description: Eth virtual VMware

  DHCP active...: No.

  IP address...: 192.168.56.1

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. :

  Adapter Ethernet Local Area Connection 3:

  The connection-specific DNS suffix. :

  ... Description: Marvell Yukon 88E8

  DHCP active...: No.

  ... The IP address: 192.168.1.12

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. : 192.168.1.1.

  DNS servers...: 203.94.227.70

  203.94.243.70

  Welcome to communities,

  -How you configure the network settings of the virtual machine?

  -The VM does not map network?

  -You use DHCP or IP settings set in the virtual machine?

  I recommend the following to the test:

  -Configure the virtual computer to use DHCP (in the virtual machine itself)

  -Configure the virtual machine for the custom virtual network adapter settings: VMnet1 (host only)

  After the virtual machine restarts, it should have a DHCP IP address and be able to communicate (ping) to 192.168.56.1

  André

• I would like to know if the IPOD Nano is able to connect and play the music of my Time Capsule Machine. Thank you

  I would like to know if the IPOD Nano is able to connect and play the music of my Time Capsule Machine. Thank you

  N ° iPod nano can play that media that is loaded on it.

  TT2

• Time Capsule/Machine and my mental health

  I approach insanity trying to untangle my time capsule. The Capsule is an A1470 with 3 TB.

  I've set up on the purchase in January with my MacbookPro also brand new - am I not lucky?

  It all worked well - wifi network, time machine - batch.

  At the end of March, we had to have a new router - BTHome Hub5.

  Everything disappeared - printer, time capsule, time ability machine work etc, yes I know the well-known story.

  I spent 3 days together precious faced with this information: Burkina Faso / plain speak for idiots like me.

  After reading what seems like everything on the forum and related links, I finally put in place the capsule time again, and it seems a network too.

  I'm not exactly sure how.

  However, it is different, and the time machine sees the TC as a new drive.

  I now have a picture of 'Data' on my desk which I believe is the previous data from backups.

  In Time Machine preferences, I'm now backup on 'Data' which is a 'new '? disc.

  Hovering on the disks of two 'data' that shows the details for the 'new' in TM preferences as follows:

  AFP: / /MyName%20mysurname; [email protected]./data

  To the previous 'data' it reads

  AFP://scrufaptc.local/data

  scrufaptc is the name of the time Capsule, I'm sure that you realize.

  Time machine seem to make incremental backups to this 'News' data and did not attempt to do a full backup.

  He knows the previous backups but won't admit it?

  Can I place the old 'Data' on the ' new 'data '?

  I destroyed it?

  Any help graciously received but not in technology talk please!

  A change of router... (HH5) caused the entire network change... It is absolutely normal.

  Whenever you change the main router of the network will change and the address of the backup.

  When you change the location... you have no other choice than to start with Time Machine... He actually never check the new target for existing backups until it starts... I wish that apple would change this function because it's confusing... However, he starts a backup... the first thing he will do is searching for existing backup that it find then check... It can take quite long time to check the backup... Once done it will be then simply do the next incremental and all is good.

  So, what do you do...

  Absolutely nothing.

  At any given time... TM may ask you you still want to use the backup of the old...

  AFP://scrufaptc.local/data

  Then you can say no...

  Otherwise, you can reset TM now yourself.

  Here see A4.

  http://pondini.org/TM/troubleshooting.html

  I don't think that you need to do it well.

  He knows the previous backups but won't admit it?

  Can I place the old 'Data' on the ' new 'data '?

  3 days of struggle of the network has worn out you.

  You can not put the old data in new data... they are after all one and the same.

  TM is thick as a brick. As I said, he might one day ask you to allow him to find the old backups... or ask you want to use at the same time... you will say no.

  Trying to go and delete the plists is not really necessary...

  And for your own sanity... It may be useful to look at actually what is the partition of data of your TC in the Finder.

  Click on the name of TC and the data to see what are the files/folders...

  You should see a sparsebundle which is your computer backup... If you see two of them to talk to me.

• External clock as a time base (NI PCI-6122)

  I use the PCI-6122 card and you want to provide an external clock very specific (preferably 10 MHz) as a time base. I tried to connect my external clock signal to PFI - 8 and then internally of PFI-8 road to the RTSI-7, but it did not work. I use only one card, and have therefore no beeing rtsi cable installed.

  Can you help me set up the card to use my external clock?

  Thank you for your help. It seems that there is no way around and I have to 'spend' an additional signal generator (locked my 10 MHz reference) to provide a sample clock, locked in my experience.

• By dividing the time base clock sample by N, we're the first sample on pulse 1 or pulse N?

  I use an external source for the time base a task of analog input sample clock. I'm dividing down by 100 to get my sample clock. Is could someone please tell me if my first sample clock pulse will be generated on the first impulse of the source of the base of external time, or about the 100th?

  I use a M Series device, but can't see a time diagram in the manual that answers my question.

  Thank you.

  CASE NO.

  CERTIFICATION AUTHORITIES,

  I don't think it's possible to use the sample clock of 3 kHz on the fast map as the time base clock sample on the slow map and get the first sample to align.  The fast card can enjoy on each pulse signal 3 kHz, while the slow card will have to meet the requirement of the initial delay before he can deliver a sample clock.  If you turn this initial delay a minimum of two ticks of the time base, the slow card eventually picking around the edges of the clock 2, 102, 202, etc..  You can set the initial delay for 100, which means that the slow card would taste on the edges, 100, 200, 300... but you wouldn't get a card reading slow on the first edge of your sample clock.

  Hope that helps,

  Dan

• divided time base

  In the simultaneous measurement with AI and AO, I used SMU-6124, that supports the time base of 80 MHz clock.

  I was told that I can use 80 M/n (integer) as a sampling in SMU-6124.

  In order to obtain n is integer, I limited my settings for 2 to 5 common factors.

  But, why the actual sampling frequency is different from the sampling frequency of entry, 1.6 MHz (n = 50).

  Real rates are 1.67E + 6 (analog input) and 1.54E + 6 (analog output).

  What is the problem for this problem?

  Any other consideration in its sampling frequency?

  labmaster.

  Hi labmaster,.

  Looks like you're on track - to answer your questions:

  0) meter tasks can use the time base of 80 MHz (20 MHz and 100 kHz are also available).  So the frequencies available, you can generate using the meter is 80 MHz/N, where N is an integer (between 4 and 2 ^ 32).  You are still limited to the average fracture, but you would work with a higher time base so you could reach the frequencies that you couldn't otherwise (for example 1.6 MHz).

  (1) you can check the actual sampling frequency of the counter by using the following property node:

  

  (2) you can run GOT it, AO and two counters at the same time in separate tasks - I'd start, AO and Ctr2 before Ctr1 so that all tasks starts at the same time.  If you started Ctr1 first, then the clock will then perform tasks would begin at different times (software-based) unless you use a trigger to start.

  I'm glad to hear that this has been helpful to you, I hope all is well and good luck to you with your application!

  -John

• Elements 3.0 - change the editing mode and a time base?

  Hey all,.

  I use Premiere Elements 3.0 and I'm trying to create a preset for my new project. My source files for this project are 23.976 frames per second, so I tried the project must match. But in the window "Custom Presets", the drop-down lists for editing and the time base Mode are grayed out - I can't change settings at nothing else than to 29.97 FPS. In addition, the only display Format options have 30 images/s.

  Is there a way I can set them to 23.976 or 24 fps?

  Thank you

  Matt

  You cannot create a custom preset to these specifications in Premiere Elements, Matt. I'm sorry.

  Premiere Elements is limited to standard formats and frame rates.

• Time record machine are inaccessible

  Time Machine said he has made in the last 3 months, but when it opens, the up/down arrows do not respond, and the chronology of the side only anime, it is not clickable.

  "Verify backups" is grayed out.

  I'm on the latest OS, high config on page 27 inch iMac (end of 2013), and the backup drive is a WD 2 connected via USB to my book (after almost 400 GB of free space).

  You must be logged in with an account that has administrator privileges.

  C.

• retrieve the time backup machine for new ssd internal

  I had to replace my internal HD on a 2012 end iMac, so I went to SSD.

  I had saved my first system and files in Time Machine before that.

  What is the process of a) formatted internal SSD new and b) recovering the original of external backup Time Machine?

  As I have to reseal the iMac just to make it work, I don't want to have to open it again to play with the new SSD!

  Hope that you already have a boot USB OS X in hand disc (I always have a copy must have on hand).

  Plug the USB into the USB port and Time Machine,

  by key pressing 'option' as soon as 'chime' begins.

  You can choose the selection of the boot drive.

  OR

  If your SSD does not start on her file (e.g. blank) - it should start automatically via the USB.

  (a) - Yes, using "disk utility" - in the menu bar superior, to partition the drive (GUID) first

  (b) then choose 'continue' to install the OS X - at the end, you will be asked few options - recover via Time Machine.

  After the restoration, you can run a few updates so that the system will work like the old set up.

  Most of the software should work, but somehow, some software required "activation key" again.

  Those notorious - Rosetta Stone (language). -J' had to communicate with them, uninstall the old drive first.  Microsoft Office can be too fickle.

  Make sure that OS X are the same version (you can't have 10.11 on Time Machine, try using the boot USB 10.10 disk) targeted installed OS X must be the same or more recent than the OS X version of the time Machine.  For example, if your Time machine backup contains 10.10, then you can either use drive start USB 10.10 and 10.11 for the restore process.

  Sam

• Time base / real-time display problems

  I am under a layout with no hardware and simulation takes 5 X longer than expected.  But when I exit graph it shows the correct output!  Is there something to put in place the basis of time?

  The installer is completely relevant.

  Sampling rate 1000 and block size 1 will bog down the software to the point where it gets behind. Because there is no equipment, you don't get a driver error... but you would. In this case, it is just work really hard. The timestamp is based on how the time of module of data generator assigned.

  1000 and 10 is almost as bad.

  I would really like to see the spreadsheet... There are modules, such as the average module, that may need to adjust the size of the block down.

• Rescue and recovery 4.52.017 backup extremely long time base

  I installed yesterday RNR 4.52.017.  The backup took 6: 30.

  

  Previous RNR 4.52.005 backup basic ran 1 hour 45 minutes.

  

  ==

  The amount of used space on C drive in November last vs last night is the same.

  All users affected by time of long term on a backup basis?

  Solved; I did not disable my A / V for the base backup.  For incremental backups, I leave a / v on. My incremental backups run 15 minutes.

  My HARD drive was like 2 pic wood saw outside.  (even my dog was barking at the disk). I woke this am to backup base of 6.5 hours. I run A / v monthly complete sweep, so I was comfortable to shoot A / v off the power when the base backup.  He is represented, this am, with a / v power off. Great watering duration. Newest RNR is therefore not a problem.

• Full time quickly machine

  I am completely confused by TM. On my MacBookPro - 10.10.5 280 GB free 500 GB and all the variable major data on DropBox (excluded from the backup) disk 1 GB TM attached with nothing else on it fills up very quickly and then does not work as I suspect TM is not deletion of things. Aware of return made up to 6 GB, which seems incredible when I come back from a break and the player has filled in 24 hours since I'm back after having been quite empty (erased the disk) before. It makes me crazy. On the other hand, a MacMini used as server (same system) with a lot of music that I continue to add to a 260 GB free of 500 GB and back up to a 500 GB drive only and is return ups up to 15 months and never fills up! Out with the MacBook and the SSD, the only difference is that the preferences of MacBook TM said it takes local photos but is not the MacMini - it's weird that I don't see anything, that can be set or changed.

  I assume you mean that you have a 1to for backups, not 1 GB drive...

  Do you use virtualization software at all? VMWare Fusion, Parallels, VirtualBox? Please keep in mind that the virtual hard drives for virtual machines are monolithic files. That means that whenever you touch one of them, the indicator is changed and the vhd file is reported as needing to be saved... It is a 10 GB file, 20 or more backed up during each hourly backup...

  Exclude your virtual machines and to periodically manually backup copies.

• How to make a single Boolean switch continuously on time bases?

  Hi all

  I'm new to labview. Tips for creating a Boolean remains off for 15 minutes, switches ON for 5 seconds, I ask... again, the same cycle should be repeated continuously. I want to start my logic by using the time of the system...

  Please guide me.

  Thank you

  Here's yet another one:

• The client Machine Info

  How can I get these last applications opened in the client using the form 10 g machine

  You can use welutil pacakge to get the files to the client directory % RECENTLY.
  then analyze each file in the directory.
  each file is recently open files on the client computer