TMSPE migration failed with "deny access".

Similar Questions

• Storage migration fails with the error: could not complete the network copy to path to the file

  Hello

  I have two hosts ESXi 5.5 with local storage and VMware vCenter device which manage them. Everything worked well until that time.

  Now when I try to make the host migration and storage, processing or power off the virtual machine, I get the error message:

  Could not complete the network for file /vmfs/volumes/.../path/to/file.vmdk copy

  The situation is the same when I try to deploy VM on ESXi-2 model that is on ESXi-1.

  All with the network configuration is correct. I have ping between the hosts on ESXi and ESXi and vCenter. No firewall hosts ESXi and vcenter. No physical firewall between hosts.

  The network latency is less than 1 ms. No packet loss.

  I read this VMware KB article: Storage migration fails with the error: could not complete network file copy and I tried solutions explained here, but the results are the same.

  You have ideas where the problem may be?

  Hello guys,.

  I finally found the problem.

  ESXi servers are configured with MTU 9000, but the switch where the hosts are connected was a bug documented with frames. I found the problem after finding this article http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1003734

  I run the command of ESXi-1:

  vmkping - d-s 8972 192.168.10.12 where 192.168.10.12 is the ip address of ESXi-2

  The result was:

  3 packets transmitted, 0 packets received, 100% packet loss

  as a workaround, I reduce the MTU to 1500, then I patched the problematic switch.

• WHS client backup fails with an access denied error

  I have a new laptop with Windows 8.1 on which I have installed the Windows Home Server 2011 connector and configuration backups for her. Backups fail at every attempt to return that an error prevented backup to create a snapshot of the volumes on this computer.

  The event log shows event ID 8194 by the following:

  The volume shadow copy Service error: error unexpected mark of the IVssWriterCallback interface. HR = 0 x 80070005 access is denied.

  . This is often caused by incorrect security settings in the process of the writer or the applicant.

  I tried to start the VSS service and tried the backup with the same result.

  The service runs with the same parameters the service runs on a computer that registers with success.

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Movie Maker fails with general access denied error

  Windows Movie Maker 6 in Windows Vista SP2 32 bit produces a general access denied error and does not run when an attempt is made to run by normal methods. Right click on the shortcut or icon and choosing "Run as Administrator" results in the successful launch of the program.

  I went to the properties of Moviemk.exe and given full control permissions to the single user and also to the administrator, but the file still does not start by double-clicking.

  Does anyone have a solution for this?

  Thank you

  Ron Carruthers

  Hello Ron_C,

  In Windows Vista and Windows 7, the number of items must be run in administrative mode. Even logged on as administrator, you are running as a standard user.

  The Movie Maker 2.6 installer must be run with administrator privileges.

  1. Select the language
  2. click on the download button.
  3. click on "Run" to start the installation.

  I hope this helps.
  Thank you

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• IPL (direct load) with OGG 12.2 fails with MGR: access denied

  Hello

  I'm doing an initial load of a table (DB12c to DB12c) 12.1.0.2

  Connect the source in the root container and on the target PDB have been verified.

  I start the extract and it stops immediately. Here is the error I get from ggserr.log.

  ERROR OGG - 01201 Oracle GoldenGate Capture for Oracle, eload01.prm: error reported by MGR: access denied.

  2016-01-08 17:12:25 ERROR OGG - 01668 Oracle GoldenGate Capture for Oracle, eload01.prm: PROCESS ABENDING.

  Any ideas?

  Here is the file eload01.prm

  EXTRACT ELOAD01

  c##ggadmin@cdb1 username, password ggadmin

  sourcecatalog pdb1

  rmthost trg, mgrport 7809

  replicat rmttask, group rload01

  table soe.addresses.

  Please ask for more if necessary.

  Thank you

  dbaOnTap

  Did some research and found the answer to my own question.  Read about it here: Initial Direct load access denied to the Oracle GoldenGate 12.2 - my experiences with Oracle technology

• TMSPE Migration fails - could not create the Group

  Hello

  The performance of the Migration tool after installation TMSPE, I get 1 error warning and 1. From downstairs, it seems that {soul} is the problem here, but where can I change it with the recommended replacements? I see not {soul} anywhere in the model FindMe Provisioning or anywhere elsewhere in the TMS...

  CAUTION:

  Caller id model invalid for mycompany group could not migrated: [email protected] / * /. Legal replacement values are {mobile_phone} and {office_phone}.

  ERROR:

  Could not create the group for {display_name = [mycompany], display_name_pattern is [{display_name}], video_uri_pattern_inherited = [false], video_uri_pattern is [[email protected] / * /], device_uri_pattern = [[email protected] / * /], device_uri_pattern_inherited = [false]} URL: / groups the exception returned by the API was the argument

  [email protected] / * /.

  is the invalid state: Code of state InvalidArgument: 1005.

  The exception message is: POST

  http://localhost:8788/ur/groups returned a 400 Bad Request response status

  Could not create the group for {display_name = [mycompany], display_name_pattern is [{display_name}], video_uri_pattern_inherited = [false], video_uri_pattern is [[email protected] / * /], device_uri_pattern = [[email protected] / * /], device_uri_pattern_inherited = [false]} URL: / groups the exception returned by the API was the argument

  [email protected] / * / is the invalid state: Code of state InvalidArgument: 1005.

  The exception message is: POST

  http://localhost:8788/ur/groups returned a 400 Bad Request response status

  Anyone can shed some light on this?

  Thank you

  Tom

  You can try to remove the device uri scheme and the findme bosses and then try to make the migration again. If its success, you can re - fill these easy once tmspe is running.

  / Magnus

  Sent by Cisco Support technique iPhone App

• iDRAC 7 launch Virtual Console fails with access denied error

  Hello

  whenever I try to launch the idrac video console 7, it fails with an "Access denied" error it's weird because I'm connected to the idrac as superuser. I use JDK 1.6. I tried through different browsers and I still get the same error.

  Found the same problem after an update of the Firmware to iDRAC.

  To address I created a new user account and permissions of base. Seems "Access Virtual Console" even when checked permissions do not actually post update.

• Steam.exe(main_exception):error:Delete of steam.exe failed, Win32 Error5 "access denied."

  I get the error that is displayed in the title line when you try to install the application of steam for the game Left4Dead. Just in case where the window title does not display the full error message:

  Steam.exe(main_exception):error:Delete of steam.exe failed, Win32 Error5 "access denied."

  My system specs are as follows:

  MB: ASUS P6T DELUXE Version2
  CPU: i7 950 QUAD-CORE 3.06GHz
  GC: XFX RADEON HD 4890 1 GB
  RAM: Patriot 12 GB Triple Channel Lat7
  HARD drive: WD VelociRaptor 150 GB 10K rpm
  HARD drive: Samsung Dual RAID Class 1 TB
  HARD drive: dual Seagate Barracuda 500 GB
  PWR: COOLMAX 1200 Watt
  CASE: Aplus Black Aluminum ATX Full Tower
  OS: Vista Ultimate 64-bit

  I checked my system and performed the following tasks to try to resolve the problem:
  My version of Windows is up-to-date. I have no problem hardware or exceptional driver. I tried to temporarily disable my antivirus to complete the installation, this does not solve the problem. I tried to install it as a system administrator. I searched the site of Valve/steam software for a solution, none were found (http://store.steampowered.com/). I searched the database of Microsoft for a solution, none were found. I'm having no problem with other games or applications that were loaded on that computer. The problem is only with the application steam.exe and any game that requires the application of steam to the function.
  I came across the following link which has promised to solve the problem;
  http://www.bing.com/search?mkt=en-us&q=steam%20error%20Win32%20error%205
  https://support.steampowered.com/kb_article.php?ref=5322-QYZB-5344  
  I followed the instructions at three times, all with the same error message.
  The default program is responsible for the following: C:\Program Files (x 86) \Steam.
  I tried to load the program on different hard disks and got the same error code.
  I have triple checked all user profiles to make sure that the appropriate privileges have been set (Admin). I checked all the steam program elements to ensure that they have been set to run as a program director executed. I double checked that proper TCP/UDP ports are open for the application of the steam function. http://www.resoo.org/docs/Counterstrike/steam_ports.html
  Any help to fix this would be greatly appreciated.

  Hello Platinum,
   
  Thank you for writing to Microsoft Vista Community Forums.
   
  This error is primarily caused by a lack of permissions for the user, having the Steam.exe file attributes set to 'Read only', or by another program interferes with the installation of Steam process (if the steam client application has been updated to a version that was not included in your package of Steam, Steam will download a new copy of itself and then delete the old file Steam.exe except when another program interferes).
   
  1. check your Windows user permissions.
  Please ensure that you are logged on as administrator on the computer that you use to install Steam.
  2. check the file attributes
  3. right click on the file Steam.exe, which was created after running the Steam Installer, and then select Properties
  4 uncheck the read-only box if it is checked and hit apply before closing the window
  5. try running the Steam.exe file once more
  6. check the settings of your security software
   
  If you are running an antivirus, firewall or any product safety program that may interfere with the removal and replacement of the file Steam.exe (some security software will check information of a file whenever it is changed and block the automatic replacement of files) Please check your settings for the program and ensure that you are prompted to authorize activities that may trigger the security software.
   
  Remove spyware, Adware and virus software and try to run the installation again.
   
  In addition to the steps above, follow these steps:
  1. go in C:/Program Files/Steam /.
  2. right click on Steam.exe and go to properties.
  3. click on the Compatibility tab.
  4. check run as administrator and click OK.
  5. then I deleted StemeTemp (or something like that. the steam icon).
  6. then run Steme.exe again.

  It will be useful.
   
  Thank you and best regards,

  Srinivas
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• error: ShellExecuteEx failed: Code 5 access denied trying to uninstall a 3rd party program.

  I was using a 3rd party appointed Start Menu Pro 7.8 program & wanted to uninstall, I use CCleaner for the same purpose, but when I tried to uninstall the program I got an error: ShellExecuteEx failed: Code 5 access denied. I've never had this error before, so was not sure of the cause of it... so I would like to know the reason for the error.

  Thank you

  Run the program with admin rights:

  http://Windows.Microsoft.com/en-us/Windows7/how-do-I-run-an-application-once-with-a-full-administrator-access-token

  Code 5 - access denied means that you don't have permissions to run the programs with rights of sweat standard.

  "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• run_job fails with permission denied for an executable work as a non - dba user

  I am running Oracle 10.2.0.4 on RHEL 5.5 32-bit and seeks to convert some of Oracle Scheduler cron tasks, but get a permission denied error during the execution of the work.
  
  To simplify things as much as possible, the below shows a work with a call to an executable shell script. The shell script was simply a calendar of Unix command, however, so it works from the command line, as well as the command-line as 'oracle' user, I get the following error:
  
  TEST: OPS$ BATCH_USER > exec dbms_scheduler.run_job ('my_test_job');
  BEGIN dbms_scheduler.run_job ('my_test_job'); END;
  
  ERROR on line 1:
  ORA-27370: slave to the job could not launch an EXECUTABLE type work
  ORA-27300: dependent operation of the OS system: access to the wrapper of extjob failed with status: 13
  ORA-27301: OS Error Message: permission denied
  ORA-27302: an error occurred at: sjsec 3
  ORA-06512: at "SYS." DBMS_ISCHED", line 150
  ORA-06512: at "SYS." DBMS_SCHEDULER', line 441
  ORA-06512: at line 1
  
  I noticed that if I create work under another account Unix which is the dba group and update the externaljob.ora run_user and run_group = s/n, the task runs without error.
  
  I assume that it is possible to run executable tasks in o/s as a group of users outside the dba (or oinstall)?
  
  Below are the details of what I did. If you would be grateful if someone can point me in the right direction. My apologies if I'm missing something obvious here...
  

  Create simple job
  
  TEST: OPS$BATCH_USER > !cat create_test_job.sql
  begin
    dbms_scheduler.create_job (
      job_name            => 'my_test_job',
      job_type            => 'EXECUTABLE',
      job_action          => '/home/batch_user/dba/v2_dba_tasks/run_script.sh',
      start_date          => NULL,
      repeat_interval     => 'freq=daily; byhour=8; byminute=30',
      end_date            => NULL,
      enabled             => TRUE);
  end;
  /
  
  TEST: OPS$BATCH_USER > @create_test_job
  
  PL/SQL procedure successfully completed.
  
  File permissions...
  -rw-r--r-- 1 root oinstall 1537 Feb 28 13:38 /u04/oracle/product/10.2.0/db_1/rdbms/admin/externaljob.ora
  -rwsr-x--- 1 root   oinstall 871282 Aug 22  2010 /u04/oracle/product/10.2.0/db_1/bin/extjob
  -rwx------ 1 oracle oinstall 871282 Aug 22  2010 /u04/oracle/product/10.2.0/db_1/bin/extjobo
  -rws--s--x 1 nobody nobody   871322 Jan 28  2009 /u04/oracle/product/10.2.0/db_1/bin/extjobO
  -rwx------ 1 oracle oinstall 871322 Jan 28  2009 /u04/oracle/product/10.2.0/db_1/bin/extjoboO
  -rwxr-x--x 1 oracle oinstall  29910 Aug 22  2010 /u04/oracle/product/10.2.0/db_1/bin/extproc
  -rwxr-x--x 1 oracle oinstall  30130 Jan 28  2009 /u04/oracle/product/10.2.0/db_1/bin/extprocO
  -rwxr-xr-x 1 oracle oinstall    327 Jan 28  2009 /u04/oracle/product/10.2.0/db_1/bin/extusrupgrade
  
  
  For testing, I'm just doing a Unix calendar command...
  [batch_user@test v2_dba_tasks]$ cat run_script.sh 
  #!/bin/sh
  
  /usr/bin/cal
  
  
  Contents of $ORACLE_HOME/rdbms/admin/externaljob.ora...
  [root@test admin]# grep '^run' externaljob.ora 
  run_user = batch_user
  run_group = comp
  
  The Unix account is not in the dba or orainst group ('comp' group only).
  
  Run from O/S...
  [batch_user@test v2_dba_tasks]$ ./run_script.sh 
     February 2011    
  Su Mo Tu We Th Fr Sa
         1  2  3  4  5
   6  7  8  9 10 11 12
  13 14 15 16 17 18 19
  20 21 22 23 24 25 26
  27 28
  
  Run as 'oracle' user...
  [oracle@test v2_dba_tasks]$ ./run_script.sh 
     February 2011    
  Su Mo Tu We Th Fr Sa
         1  2  3  4  5
   6  7  8  9 10 11 12
  13 14 15 16 17 18 19
  20 21 22 23 24 25 26
  27 28
  
  But running from scheduler results in error...
  TEST: OPS$BATCH_USER > exec dbms_scheduler.run_job('my_test_job');
  BEGIN dbms_scheduler.run_job('my_test_job'); END;
  
  *
  ERROR at line 1:
  ORA-27370: job slave failed to launch a job of type EXECUTABLE
  ORA-27300: OS system dependent operation:accessing extjob wrapper failed with status: 13
  ORA-27301: OS failure message: Permission denied
  ORA-27302: failure occurred at: sjsec 3
  ORA-06512: at "SYS.DBMS_ISCHED", line 150
  ORA-06512: at "SYS.DBMS_SCHEDULER", line 441
  ORA-06512: at line 1

  Hello

  The run_user specified in externaljob.ora don't have to be a member of the oinstall group.

  I think you can run into a problem specific to run_job with use_current_session-online set to true when the local OS user running sqlplus is not a member of oinstall.

  The same error occurs with a background task run (for example use_current_session-online fake)? Occur if you are using sqlplus from another machine?

  Thank you
  Ravi.

• System 32 error (0x00000020): "the process cannot access the file because it is being used by another process.". The operation to open the file will fail with error - 1032 (0xfffffbf8(JET_errFileAccessDenied))"

  Original title: svchost (1020)

  Event type: error
  Event source: ESENT
  Event category: general
  Event ID: 490
  Date: 2010-10-19
  Time: 14:51:34
  User: n/a
  Computer: ROB
  Description:
  Svchost (1020) an attempt to open the file "C:\WINDOWS\system32\CatRoot2\{127D0A1D-4EF2-11D1-8608-00C04FC295EE}\catdb" for read / write access failed with the error System 32 (0x00000020): "the process cannot access the file because it is being used by another process.".  The operation to open the file will fail with error - 1032 (0xfffffbf8(JET_errFileAccessDenied)).

  For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Hi Robrw,

  1. when exactly you receive this error?

  2. don't you make changes to the computer before this problem?

  You can try to rename the catroot2 folder and check if it helps.

  Step 1:

  a. Click Start and in run type C:\windows\system32 and click ok

  b. find the Catroot2 folder. Right-click on Catroot2 and rename it to Catroot2.old

  If you are not able to do the normal mode, try to start in safe mode and rename

  Check out the link for more information on starting your computer in SafeMode below:

  http://support.Microsoft.com/kb/315222

  Step 2:

  If you are unable to access the catroot2 folder, and then try to change the permissions on the files and check if it helps.

  See the following article:

  How to capture a file or a folder in Windows XP

  http://support.Microsoft.com/kb/308421

  Step 3:

  You can also try to temporarily disable third-party security software and firewalls and check what is happening.

  Note: Activate the security software after the resolution of the problem.

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Error creating registry key, RegCreateKeyEx failed; Code 5 access denied

  Just as the title says. I encounter and error where a program is unable to create a registry key. Error 5, access denied. I tried as admin and the problem still persists. I tried to run the registry editor and access, but still the problem persists.

  For the complete error message:

  HKEY_LOCAL_MACHINE/SYSTEM/CurrentControlSet/Control/MediaProperties/PrivateProperties/Joystick/OEM/V8/AXES/0ID_8888 & PID_030

  RegCreateKeyEx failed; Code 5 access denied

  I can retry, ignore, stop the program. I run Windows 7. It is a big problem for me because this PC is also to play games, can't really do this without my will.

  I solved the problem some time ago btu don't remember how. I think trying to let the program us firewall or try to disable all firewall and installed, I'm pretty sure something along these lines has helped.

• Deny access to Internet with PIX 500 series

  I need deny all access to the Internet for some guests at various locations. We use the PIX 501 and 506 firewalls to create a full mesh of VPN between offices. How to configure access lists to deny access to the Internet to only a certain number of hosts?

  Configure an access inside the interface list and begin by denying the host that you want to block after that add the hosts and protocols that should be able to connect to the Internet.

  example:

  Internet access list deny ip 192.168.1.10 host everything

  Internet access list deny tcp host 192.168.1.10 any eq 80

  allow Internet access list ip 192.168.1.20 host a

  ...

  Give me a more detailed example.

  You can also work with groups of objects to be more specific and group several UDP or TCP port.

  example:

  object-group service tcp Web

  EQ object of port 80

  EQ object of port 443

  object-port eq 21

  internet access list deny tcp 10.2.1.0 255.255.255.0 any object-group Web

  Internet access-list permit tcp host 10.2.1.10 a host Web object-group

  allow a whole list of internet access

  sincerely

  Patrick

• I have the following error message when you try to access the settings preferences "load library failed with error 1114: (DLL) initialization routine failed. I use Windows OS 10. Can anyone help?

  I have the following error message when you try to access the settings preferences "load library failed with error 1114: (DLL) initialization routine failed. I use Windows OS 10. Can anyone help?

  HI lifeimagecreations

  Greetings!

  Please see this thread in the lightroom preferences entry CC2015 crashes with LoadLibrary failed with error 1114

  If this does not work, reinstall the program with administrative rights.

  Let us know if this helps

  Concerning

  ~ Assani

• ORA-27369: jobs of type EXECUTABLE failed with exit code: permission denied

  Dear experts,
  
  I created a simple external job to run the export job (expdp) to be run from PL/SQL. When I create a job as user SYS, labor runs well, but the same fails when I run it as a user of the application. I'm sure I'm missing a few privileges. I go through internet, MOS for a solution, but could not find a (my bad!).
  
  Grateful if you could point me the right direction.
  
  Here is the work:
  

  BEGIN
  dbms_scheduler.create_job(
  job_name => 'mytestjob',
  job_type => 'executable',
  job_action => '/u01/myexpdp.sh',
  enabled => TRUE,
  auto_drop         =>   FALSE);
  END;
  /
  
  
  exec dbms_scheduler.run_job('mytestjob');

  performance of the work as a user 'TEST '.
  

  SQL> show user
  USER is "TEST"
  SQL>
  
  SQL> exec dbms_scheduler.run_job('mytestjob');
  BEGIN dbms_scheduler.run_job('mytestjob'); END;
  
  *
  ERROR at line 1:
  ORA-27369: job of type EXECUTABLE failed with exit code: Permission denied
  ORA-06512: at "SYS.DBMS_ISCHED", line 185
  ORA-06512: at "SYS.DBMS_SCHEDULER", line 486
  ORA-06512: at line 1
  
  
  SQL>

  permissions of files

  -rwxrwxrwx 1 oracle oinstall 1539 Mar 21 17:58 /u01/myexpdp.sh

  expdp script

  cat /u01/myexpdp.sh
  
  #!/bin/bash
  source /home/oracle/.bash_profile
  
  ORACLE_SID=TESTDB
  
  /u01/app/oracle/product/11.2.0.1/db1/bin/expdp parfile=/u01/expoptions.txt

  expdp settings file
  

  cat u01/expoptions.txt
  userid=scott/tiger
  directory=DATA_PUMP_DIR
  dumpfile=test.dmp
  tables=emp

  Published by: Prem Kumar on March 21, 2013 04:14

  Have you defined a credential for your host with dbms_scheduler.create_credential connection and specified the credentials with the work?
  --
  John Watson
  Oracle Certified Master s/n
  http://skillbuilders.com