Trying to replace a XP computer with another XP computer in a peer-to-peer network with two other computers.

Similar Questions

• Just started to get a message saying that my product no longer works because I installed it on two other computers, my other computers do not work, then the facility in my new computer it worked for a little while, then this message kept popping up, what

  Just started to get a message saying that my product doesn't work more because I installed it on two other computers, my other computers do not work, the installation in my new computer, it worked for a little while, then this message kept popping up, what can I do to make it work on my new computer?

  For more information on the activation or deactivation of Adobe products on your computer, please follow the instructions contained in this document:

  Activate or deactivate an Adobe product

  You can also make reference to: connect and disconnect from the desktop Adobe Creative Cloud application

  I hope this helps.

  Concerning

  Megha Rawat

• Network management problem, computer laptop Windows 7 will not find other computers on any network, however all other computers on the network can access Windows 7 laptop.

  Basically, the issue I'm having is that my laptop does not connect to any other computer to access the actions or other files.  Other computers on the network can access my computer laptop shares and files without any problems.  Operating system is Windows 7 Home Premium x 64.

  What I tried:

  restarted
  uninstalling and reinstalling the files and printers, sharing maps and restart after completion
  all disabled firewall
  tried with IPv6 enabled and disabled without change, so it is currently enabled
  tried on a Wi - Fi and the differences are listed below in the section work (work is wireless)
  able to ping other comptuers
  access to other computers is permitted by other computers

  problem extends over several networks, IE I noticed it at home last night and the followed problem my laptop at work this morning.
  The problem is slightly different on the two sites.

  At home:
  I can see the other computers on the network, but I am unable to access it, even if I have permission, but other computers can access to my laptop.

  At work:
  Cannot even find other computers on the network but they can find and access my laptop.

  I have worked on this problem of non stop for several hours and did much more than what is said, but I am unable to remember everything.  I should have been taking notes: P

  Here are the results of the ipconfig/all command (I removed the physical addresses for security reasons):

  Windows IP configuration

  Name of the host...: Radiation-G72
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless Network Connection 2 wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft Virtual WiFi Miniport adapt
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. : hsd1.ga.comcast.net.
  Description...: Realtek PCIe GBE Family Controller
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Atheros AR928X Wireless Network adapt
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::f4e3:cd1c:6952:eb4d % 11 (Preferred)
  IPv4 address: 192.168.2.7 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: Thursday, February 4, 2010 10:50:32
  End of the lease...: Friday, February 5, 2010 08:29:36
  ... Default gateway. : 192.168.2.1.
  DHCP server...: 192.168.2.1.
  DHCPv6 IOOKING...: 234890707
  DHCPv6 DUID customer...: 00-01-00-01-12-4C-6E-91-00-25-D3-3D-FC-9A
  DNS servers...: 192.168.2.1.
  NetBIOS over TCP/IP...: enabled

  Tunnel adapter isatap. {1797D168-6FC8-4DDF-8338-4E214119C26D}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft ISATAP adapter
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Teredo Tunneling Pseudo-Interface:

  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2001:0:4137:9e74:4ea:2920:b81a:cdc5 (Preferred)
  Address IPv6 local link...: fe80::4ea:2920:b81a:cdc5% 13 (Preferred)
  ... Default gateway. : ::
  NetBIOS over TCP/IP...: disabled

  Card adapt 6TO4 tunnel:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 card
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Asked this question in the Windows 7 forum also because the problem was between windows 7 and Vista.

  Hello

  If it has started, you can try a system restore - an update "might" have caused the problem.

  1. try a system restore back to a point before that happened. And immediately thereafter enter
  Control Panel - Windows updates - top left settings and set it to download and informs you instead
  Automatic. Leave it until you are sure that everything is OK and then you can add them one at a time
  to troubleshoot BUT click right on and HIDE all the driver updates. Also stop at day of drivers like below
  and let this value - manually search for drivers when you think you need. (See how and why to)
  stop day of drivers below.)

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  To uninstall an update if you determine that there are problems - Panel - updated Windows - down left-
  Updates installed - uninstall

  I had completely forgotten the system restore!  While looking into the system restore, I found that when I moved into my new House and has cable Internet installed, the cable technology installed a program of comcast on my computer.  This caused me to not be able to connect with other computers.  After rolling back to install it before it works!   Thank you.

• Some Web pages won't load does not (hanging) in Firefox 6 and 7. No improvement in Mode without failure or clearing cache/cookies. Pages work fine in Chrome and IE and Firefox 5.0.1 on this computer and also fine load in Firefox 7 on other computers.

  On my main computer, Firefox 6 and 7 will not load some Web pages (redsox.com, for example - pages just block indefinitely). Boot safe mode does not help. I keep downgraded to 5.0.1 and loads pages very well; they charge both in Chrome and IE. In addition, pages loading in Firefox 7 on other computers, it seems to have a problem with this configuration/installation...have deleted the cache and cookies without improvement. Any advice?

  I would create a new.

• How to replace the audio clip with each other instead of stack

  I'm editing a long track of narration in Audition, and I have to paste a small audio clip on narrative in several places.  I want the pasted clip to replace this part of the narrative, as it would in first.  What he does in hearing is battery clips, so if I choose narration for some reason, all the clips on the top of the narration are now moved behind her.  To get back them, I now spend the narration to an empty track clip, do the same with those who went behind and everything put back in the correct order.

  Is it possible to have the clip pasted to replace what you paste it above as it would in first?

  Thanks in advance for the help!

  Phillip

  With the help of hearing CC 2015.1 build 8.1.0.162

  No, unfortunately, if you work in multitrack view. An easy insertion function was requested to do exactly what you want but is not yet available.

  The simplest solution is to split the clip to where you want to insert the new plug. You can do this either by using the Razor tool or the shortcut Ctrl-K. Then when you place the new clip on top it will show melted shackled at both ends. If you select one of the parts of the original item, you can click on the edge and drag it to the appropriate end of the new clip (leaving a chained if you wish or not fade).

• Problem in trying to share a search box with two reports

  Hello! I have two reports (report 1 and I2) in two different pages. In two pages, I have the same list of selection (Item1 and Item2). I want something to choose in the list (Item1) Report1 selection and my choice to be saved in the select list (Item2) Report2 too. Can someone help me please?
  Is it possible to have a list of selection for the two reports?
  
  Thanks in advance for any answers...
  
  Published by: user10642834 on May 8, 2009 10:15

  Hello:

  You can set the selection list in a region on the page 0. Apply a condition on the region to only show for pages containing your reports.

  CITY

• My computer guard give up a connection to the network but the other computers in the House are connected

  My computer said at the outset that it is correctly connected to the network but then immediately lose the connection. Sometimes it will say that I limited the connection, but the strength of the network is always excellent. Computers are my roommates are working properly. Initially, he says that TataraTmp is the network of choice. I tried to delete this network that I am still unable to connect.

  Hello

  I guess that it is a wireless computer.
  ------------------------------------

  Maybe this can help.

  Assuming that the signal is strong, and that there is no noise in the electrical environment (http://www.ezlan.net/wbars.html ).

  Uncheck the box to the NIC of energy economy (I.e., do not leave the card save energy).

  There may be some variations on where is the energy saving setting.

  Here are a few examples, YMMV, look around your systems.

  Example, http://www.ezlan.net/example/powersave.jpg

  Example, http://www.ezlan.net/Win7/power_sav_wireless..jpg

  Example, http://www.ezlan.net/Win7/power_save_win7.jpg

  Example, http://www.ezlan.net/Win7/adv_power-sav.jpg

  ----------------------------

  Still a problem?

  Check the support site for the manufacturer of the computer and make sure that you use the latest drivers.

  If the support site has a newer version of the drivers and installed current ask drivers the most up-to-date drivers use this method.

  Download the drivers and extract them to a folder of your choice.

  In Device Manager, right-click on the adapter.

  Click Update drivers and choose her browse my computer for drivers.

  Choose let me a list of choices, click on disk and point to the folder with the drivers.

• ACS same username with two other group, two profiles of shell

  Hello

  In my ACS 5.4 I want to have same useranme using two profiles of shell. This is the requirement.

  Profile of a shell with privileges for admin peripheral IOS 15 and another with different privilege admin WCS. Because there may be two profiles of shell on the same profile authroization, I created two different profiles and correspondence with the name of the local group of ACS. However, whenever the user tries to access it always hits 1 profiles.

  I'm not sure that I missing something, if someone has or knows how to do this please advise.

  Thank you

  Hello

  What you can do is to create two authorization rules based on the ip address.

  Use two rules:

  rule 1: If the ip address is wcs ip address then use WCS-Shell-profile

  rul3 2: If the ip address of the device do not match the wcs ip address then use: other-Shell-profile

  If you don't see the ip address in the rule options, you can always customize what options you want to compare from the button customize at the bottom right of the page.

  HTH

  Amjad

  Rating of useful answers is more useful to say "thank you".

• Problems with HP4620 not working only not with the other computers in the House

  I bought a HP 4620 for my house and it works very well with my Vista laptop wireless.  However, it does not show as an option for our office or our second laptop.  Any ideas?

  Thanks, Sunny12

  Hello sunny

  I was going through your posts and help you've been putting online...

  Answered by Mr. Aneesh, pilots refers to the software that we are supposed to install in the computer.  Thus, these drivers are available on the CD that you have with your printer...

  Now, as you begin to install, you will get the screens user friendly and just follow the instructions and proceed with the installation.

  The system, that is to say; the monitor (computers) will ask you how you are going to connect the printer to the computer...

  Thus, there are 2 methods by which you can connect your printer to the computer...

  (1) USB - this is a cable that you find in the box the printer, but you would have to buy separately.  so, if you do not, please get one of the stores.

  (2) wireless - in this type of connectivity, you do not need the USB cable, because you would then have a device called a 'router '...  And here... It is the router that establishes the communication between the computer and the printer.

  Please try the following and if you get stuck, let us know.

  Kind regards

  Ashokkan.

  Help the community by marking this post.
  Your question has been answered? Mark it as an acceptable Solution.
  See a great post? Give it a Bravo!
  I work for HP

• Try to plug it into the router which is already installed and running with the other computers in the House.

  My computer says "Windows cannot find the certificate to connect to the network."  This computer is working - and an administrator.  This person could not help me.  Hope someone here can...

  The 'certificate' this computer is looking for is something that is used in networks wireless business and almost never in home wireless networks.

  The following assumes that you have given to your home network wireless (SSID of the router) "name" which is recognizable as yours and different from the network name to your work.

  The following also assumes that you are using Windows XP service pack 3 and you use to control your wireless Windows Wireless Zero Configuration (WZC) adapter.

  If none of these assumptions are not correct, provide the relevant information.

  If all of the above assumptions are correct, then

  • Open network connections (start > run > ncpa.cpl > OK)
  • Right-click on the icon for your wireless adapter and select Properties
  • Click the "Wireless Networks" tab.  This is where you confirm that "Use Windows to configure my wireless network" is checked. If it is not checked, stop here - you need to identify the utility that controls your wireless adapter before continuing. a good place to look is the icons in the Notification area (next to the time display)
  • Select your network (SSID of your router) from the list of "Preferred networks", and then click Properties
  • Click on the "Authentication" tab and uncheck the box for "enable authentication IEEE 802. 1 x for this network. "
  • OK your way out.

  If "allow authentication IEEE 802. 1 x for this network"is checked, but grayed out, so you can't change it, click 'Cancel' to return to the"Wireless Networks"tab and"Remove"the entry of your router.  Then click on "View Wireless Networks", select your router, click Connect and enter your password when you are prompted.

• I would like to know how to scan my computer to see if my boyfriend had our two laptop computers secretly connected so that it can monitor me remotely

  It has installed 2 drivers wireless separated when we went to windows 7 tent still failure to upgrade me to windows XP, Vista, now all three operating systems are on my lap top. When we went to the high grade that I wanted to pour what I felt I could just learn everything if I did on mine, when he checked the drivers there were GOBS of drivers intell temporary, while it just started clicking on buttons & partitioned the computer once more. I think that one of the drivers it can control remotely. I had my screen change "all by themselves -" I have search, and I wonder if it is possible that his phone Samsung for a remote view in my lap top so where & how should I go see?

  If you have a retail DVD of Windows 7 and you want to clean up all (or do not care if you do), why not go ahead and do your own clean install of Windows 7 (assuming that your laptop can support Windows 7)?  See http://www.sevenforums.com/tutorials/1649-clean-install-windows-7-a.html

  You have to collect the drivers before you start.  Visit the website of the manufacturer of your laptop and search using your serial number (if you have one).

  This article is for Dell computers, but it gives you an idea of the drivers you need and the order in which you should install them. Of course, if you do not have a Dell PC, you would skip things like items 1, 8 and 9.

  If this guy is still your boyfriend and has physical access to your computer, you should treat your question socially rather than technically.

• How can I replace my 2008 TC with a 2016 news?

  Use the old 500 GB TC since LAN with two laptop computers and two AP Express as Extender.

  Just bought a 2 to TC to replace the 500 GB TC.

  Some critics of the new TC reviews say just turn on the new TC and it copies the settings from the old TC and off you go. I think the steps are left out of this process.

  First question, is the new TC turned on when the old TC is turned on and connected to a cable modem or vice versa?

  Second question, how to use the AP utility to facilitate this? I want to continue to use extenders of MONKEY.

  I will also need to set up Time Machine, but I can handle it once the new TC is the host of the local network.

  Thank you;

  Let the old TC in walking normally on your network.

  Connect an Ethernet cable from one of the <>- on the old TC LAN ports to the "O" on the new TC WAN port

  Turn on the new TC and let it run a few minutes

  Click the WiFi icon at the top of the screen on your Mac and are looking for a list of the new AirPort base station

  Just below that, click on the Time Capsule.  The example below shows an AirPort Extreme as the new Base Station, but on your screen, you will see the Time Capsule

  

  When you click Time Capsule, which will get the 'Assistant' Installation running.  It will take a few seconds to analyze things and offer a Setup program based on what it "sees".

  The Wizard usually guesses correctly, but in this case, it will guess wrong, because the installer suggested using the new TC to extend the network will not be the configuration that you want.  The example below shows an AirPort Express, but you will see the new time Capsule on your screen with the old TC.

  

  Click the other Options in the lower left corner of the window

  Select the option replace an existing device and click Next

  

  The next window will ask you to confirm what product you want to replace and explain the parameters of the old TC will be transferred to the new TC. When this happens, the old TC will automatically reset back to default settings.

  Once the installation process completed, powering down of the entire network and replace the old with the new TC TC, using the same hook ups.

  Turn on the modem first and let it run for a few minutes

  Start the next device connected to a modem and let it run for a minute

  Keep a minute out one at a time until the entire network is back of boot devices

  With luck, everything will work the way it was before

  You need to configure Time Machine to revisit the new TC.

  After doing this several times, I am not convinced that the process of 'Replace' is just as easy and faster than the simple implementation the new TC as a new device and simply using the same wireless name, same of passwords, etc. as the old TC.  But, users appear to want to use replace it option rather than doing things manually.

  It's your call. Good luck!

• Apple TV 4 cannot be used simultaneously with the other Apple TV

  We have just added a 4 AppleTV to our collection of the 2nd and 3rd generation AppleTV (all run wifi that we're not wired Ethernet in the House). For the first week or so it was no problem to start the 4 AppleTV and one of the other two, but since yesterday on the AppleTV 2nd generation (just to set market and access to iTunes or my library, not really look anything like that) not only causes the AppleTV 4 deadly freeze, but I end up having to restart the modem and the router with the computer (note that) (, meanwhile, the AppleTV 2 seems to work but I get annoyed at to get the 4 works again and just had to turn off so I don't know how stable, it has been). I have a modem/router Netgear of Cox (even when the AppleTV 4 wasn't running, SpeedTest has returned a normal wifi speed) I only use as a modem and a Terminal Airport Express as my wifi router. My operating system in Windows 10. Nothing updated (other than the Synaptics touchpad software) between when he was working Friday and when he decided to stop playing at the same time on Saturday. Once the computer, the AppleTV 4, the router and the modem has restarted, I once more have access to my iTunes to the AppleTV library and play something.

  I still have intermittent problems where the AppleTV 2 and 3 suddenly decide that they cannot see my library and I have to restart iTunes (which is completely unrelated to the current issue and I'm sure function of the way that Windows treats Hello), but in the case of the AppleTV 4 trying to run at the same time as the AppleTV 2 restart iTunes does nothing. Even with completely disconnected the AppleTV 2, restart iTunes (and even the computer) and restart the AppleTV 4 I'm not even to mirror content access purchases through the iTunes store or iTunes on Windows to the AppleTV, so my conclusion that I had to reboot the router and the modem, which was the only way to return the feature.

  At one point we tried to replace the AppleTV 4 with 3, and he was unable to work as the AppleTV 2 and these two have been exploited in tandem for about 3 years now generally without interference other than a problem when we suddenly decides that he cannot see my sharing even if the other is played.

  If someone has any ideas as to why I am suddenly unable to run two AppleTV at the same time, I would like to know. I don't have time to get into it tonight we try to watch a movie, but I think to restore the AppleTV 4 factory settings and see if that solves this problem. I'm also fooling around with the configuration of the 3 units when I have the House to myself and are not trying to keep anyone entertained. I'll post back tomorrow if I can get 2 & 3 or 3 & 4 at the same time. I hope I get lucky and be able to operate in any combination again.

  Just a quick suggestion. Have you given different names mountain BIKING? Apple protocols for colocation and AirPlay are based on these names and get confused if devices with different IPs claim the same name.

• No wifi connection have the connection with other computers

  Unable to connect to internet with wifi connection ok with the ethernet cable.    disabled Kaspersky antivirus (no change) have used the restore of the system (no change) I have two other computers and connection ok.   Have tried internet explore and Google Chrome - neither work.   With Google Chrome get error 106.   Uninstalling Google Chrome (no change)

  Hello

  Did you change your computer?

  I suggest you to see the links and check.

  Network connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  The problems of Internet connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  See also:

  Wireless network card: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/wireless-networking-frequently-asked-questions

• How to unregister a computer broke so I can install Cs6 on other computers?

  Hello!  I have failed and could use some help.  I have two computers, one of which does not work at all.  Both of these computers have my Adobe Cs6 Suite installed on it.  I want to cancel the registration of these computers so that I can install and use the Cs6 Suite on two other computers.  How can I cancel both of these computers, especially when I can no longer use the broken computer?

  Thank you for your time and help!

  When you have a non-functional computer and cannot turn off

  Don't forget to request ONLY activation support set your number of activations

  Serial number and activation support (no-Cloud) https://forums.adobe.com/thread/2041990