Trying to set up the VPN Client with crossed on ASA5510

Hello

I'm putting in place our ASA5510 so that users can connect to our LAN to work and surf the Internet as well.

I followed the guide from Cisco, I connect and I give myself a 192.168.10.x necessary address but I can't connect what on our network of 10.0.0.0/24 or surf the Internet work.

Could someone please check my config and see what's wrong, there's also a vpn L2L here in a 192.168.3.0 network, but that works without problems

Thank you very much

Chris

Hello Chris,

Add after access list statement.

INSIDE_nat0_outbound to access ip 10.0.0.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0

And for the aggregation of internet traffic add following command:

permit same-security-traffic intra-interface

Verify and validate the results.

HTH

Sangaré

pls rate helpful messages

Tags: Cisco Security

Similar Questions

IP address connection sets using the VPN Client

Hello world. I'm using a VPN Client when I establish a VPN Tunnel with a 1600 router, and I have a question.

Can I assign a fixed IP address in the client, instead the router send to random addresses from customer?

What I would he do this?

It would be in the configuration of the VPN client, or in the configuration of the router?

If so, I'm doing this?

Do I need another tool, or other software or hardware to do?

any help is hope...

Thank you...

Hello

I don't think that there is a simple way to do this.

However, if you create a different groupname for the user who needs a static IP address, I think you should be good to go

So what you need to do, create a new pool of addresses. Make the start and end ip address be the same (this is the address to which you want to assign to the VPN user)

Configure another ipsec on the router group and bind the new pool to this group

Ask your VPN client to connect to this group

Hope that helps

Jean Marc

The dynamic firewall application on the VPN Clients with ASA

Hello

I'll put up a Cisco ASA to complete the remote VPN client connections, but I want to assure you that the dynamic firewall is enabled on the client.

I know it's possible with the VPN concentrator, but cannot see any documentation detailing that can be performed on an ASA.

Anyone encountered this?

Thank you

James

I believe you can use Group Policy settings to configure the firewall client.

You can find more information about this feature in the migration to http://www.cisco.com/en/US/docs/security/asa/asa72/vpn3000_upgrade/upgrade/guide/migrate.htmlguide.

Hope this helps.

Andrea.

Step 1 under Configuration > VPN > General > Group Policy Panel, select group policy in the table and

Click on change. ASDM displays the Edit Group Policy dialog box.

Step 2: click on the customer Firewall tab Figure 5-6 shows the firewall client options configured for this example:

• Inherit-disabled (disabled)

• The required Firewall Firewall setting

• Type firewall Cisco Integrated Client Firewall

Firewall policy-policy (CPP) pushed •

Terminating the VPN client on 871W

Hello

I tried to install EasyVPN on a cisco 871W by SDM. The goal is to finish the VPN client with authentication with an external RADIUS/advertising (on a local subnet). I implemented the IAS on a win2003 Server advertising and checked the accounts.

SDM was missing the 'crypto map' piece of config. After you add this in the CLI it still didn't work. Thus, EasyVPN is not as easy at is sounds...

Could someone with some knowledge of VPN and IPsec and so forth please look at this config? Maybe it gives me an idea of what I did wrong (which, without a doubt, must be the case).

Thank you

Erik

==

AAA new-model
!
AAA rad_eap radius server group
auth-port 1645 10.128.7.5 Server acct-port 1646
!
AAA rad_mac radius server group
!
AAA rad_acct radius server group
!
AAA rad_admin radius server group
!
AAA server Ganymede group + tac_admin
!
AAA rad_pmip radius server group
!
RADIUS server AAA dummy group
!
AAA authentication login default local
AAA authentication login eap_methods group rad_eap
AAA authentication login mac_methods local
AAA authentication login sdm_vpn_xauth_ml_1 local
AAA authorization exec default local
AAA authorization ipmobile default group rad_pmip
AAA authorization sdm_vpn_group_ml_1 LAN
AAA accounting network acct_methods
action-type market / stop
Group rad_acct
!
!
!
AAA - the id of the joint session
clock timezone MET 1
clock to DST DST PUTS recurring last Sun Mar 02:00 last Sun Oct 02:00
!
Crypto pki trustpoint TP-self-signed-1278336536
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 1278336536
revocation checking no
rsakeypair TP-self-signed-1278336536
!
!
TP-self-signed-1278336536 crypto pki certificate chain
certificate self-signed 01
3082024A 308201B 3 A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
69666963 31323738 33333635 6174652D 3336301E 170 3039 31303237 32313237
32395A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 32373833 65642D
33363533 3630819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
81008B 56 5902F5DF FCE1A56E 3A63350E 45956514 1767EF73 FEC6CD16 7E982A82
B0AF8546 ABB3D35A B7C3A7E3 3ACCB34A 8B655C97 F103DBD5 9AAEFEFC 37A 02103
4EFC398B 0C8B6BE5 AD3E568E 6CB69F87 CBCA0785 EAED0A28 726F2F0A B0B0453E
32E6B3B7 861F87FA 222197DD 3410D8A9 35939E9B CBF95F20 B8DA6ADE BF460F5C
BF8F0203 010001A 3 72307030 130101 1 FF040530 030101FF 301D 0603 0F060355
551 1104 16301482 12444341 4E495430 302E6361 6E2D6974 2E657530 1F060355
1 230418 30168014 84C9223E 661B2EB4 5BAB0B0E 1BE3A27A 64B3AEB0 301D 0603
551D0E04 16041484 C9111E66 1B2EB45B AB0B0E1B E3A27A64 B3AEB030 0D06092A
010104 05000381 8693B 599 70EC1F1A D2995276 F3E4AF9D 81002F4A 0D 864886F7
17E3583A 46C749F9 38743E6F F5E60478 5B9B5091 E944C689 7BA6DCA2 94D2FBD3
AFDE4500 A0A3644E 603A852D 55ED7A87 93501D5C 1662DAED 3FFFEC5A F1C38ED4
E0787561 BA5C14A3 6D065FCF 7DBDEBB6 9186C2D9 AA253FBF A9E38BC3 342C3AC9
2BEF6821 E4C50277 493AD5B6 2AFE
quit smoking
dot11 syslog
!
IP source-route
!
!
DHCP excluded-address IP 10.128.1.250 10.128.1.254
DHCP excluded-address IP 10.128.150.250 10.128.150.254
DHCP excluded-address IP 10.128.7.0 10.128.7.100
DHCP excluded-address IP 10.128.7.250 10.128.7.254
!
pool IP dhcp VLAN30-COMMENTS
import all
Network 10.128.1.0 255.255.255.0
router by default - 10.128.1.254
10.128.7.5 DNS server
-10.128.7.5 NetBIOS name server
aaa.com domain name
4 rental
!
IP dhcp VLAN20-STAFF pool
import all
Network 10.128.150.0 255.255.255.0
router by default - 10.128.150.254
10.128.7.5 DNS server
-10.128.7.5 NetBIOS name server
aaa.com domain name
4 rental
!
IP dhcp SERVERS VLAN10 pool
import all
Network 10.128.7.0 255.255.255.0
router by default - 10.128.7.254
10.128.7.5 DNS server
-10.128.7.5 NetBIOS name server
aaa.com domain name
4 rental
!
!
IP cef
no ip domain search
IP domain name aaa.com
inspect the tcp IP MYFW name
inspect the IP udp MYFW name
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
VPDN enable
!
!
!
username privilege 15 secret 5 xxxx xxxx
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
ISAKMP crypto client configuration group vpn
key xxxx
pool SDM_POOL_1
netmask 255.255.255.0
!
!
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
!
crypto dynamic-map SDM_DYNMAP_1 1
market arriere-route
!
!
card crypto SDM_CMAP_1 client authentication list sdm_vpn_xauth_ml_1
map SDM_CMAP_1 isakmp authorization list sdm_vpn_group_ml_1 crypto
client configuration address map SDM_CMAP_1 crypto answer
map SDM_CMAP_1 65535-isakmp dynamic SDM_DYNMAP_1 ipsec crypto
!
Crypto ctcp port 10000
Archives
The config log
hidekeys
!
!
!
Bridge IRB
!
!
interface Loopback0
10.128.201.1 the IP 255.255.255.255
map SDM_CMAP_1 crypto
!
interface FastEthernet0
switchport access vlan 10
!
interface FastEthernet1
switchport access vlan 20
!
interface FastEthernet2
switchport access vlan 10
!
interface FastEthernet3
switchport access vlan 30
!
interface FastEthernet4
no ip address
Speed 100
full-duplex
PPPoE enable global group
PPPoE-client dial-pool-number 1
No cdp enable
!
interface Dot11Radio0
no ip address
Shutdown
No dot11 extensions aironet
!
interface Vlan1
address IP AAA. BBB. CCC.177 255.255.255.240
no ip redirection
no ip proxy-arp
NAT outside IP
no ip virtual-reassembly
No autostate
Hold-queue 100 on
!
interface Vlan10
SERVER description
no ip address
IP nat inside
no ip virtual-reassembly
No autostate
Bridge-group 10
Bridge-group of 10 disabled spanning
!
interface Vlan20
Description of the STAFF
no ip address
IP nat inside
no ip virtual-reassembly
No autostate
Bridge-group 20
Bridge-group 20 covering people with reduced mobility
!
Vlan30 interface
Description COMMENTS
no ip address
IP nat inside
no ip virtual-reassembly
No autostate
Bridge-group 30
Bridge-group 30 covering people with reduced mobility
!
interface Dialer1
MTU 1492
IP unnumbered Vlan1
no ip redirection
no ip proxy-arp
NAT outside IP
inspect the MYFW over IP
IP virtual-reassembly
encapsulation ppp
Dialer pool 1
Dialer-Group 1
PPP authentication pap callin
PPP pap sent-name of user password 7 xxxx xxxxx
!
interface BVI10
Description the server network bridge
IP 10.128.7.254 255.255.255.0
IP nat inside
IP virtual-reassembly
!
interface BVI20
Description personal network bridge
IP 10.128.150.254 255.255.255.0
IP nat inside
IP virtual-reassembly
!
interface BVI30
Bridge network invited description
IP 10.128.1.254 255.255.255.0
IP access-group Guest-ACL in
IP nat inside
IP virtual-reassembly
!
pool of local SDM_POOL_1 192.168.2.1 IP 192.168.2.100
IP forward-Protocol ND
IP route 0.0.0.0 0.0.0.0 Dialer1
IP http server
access-class 2 IP http
local IP http authentication
IP http secure server
IP http secure ciphersuite 3des-ede-cbc-sha
IP http secure-client-auth
IP http timeout policy slowed down 60 life 86400 request 10000
!
!
overload of IP nat inside source list 101 interface Vlan1
IP nat inside source static tcp 10.128.7.1 25 AAA. BBB. Expandable 25 CCC.178
IP nat inside source static tcp 10.128.7.1 80 AAA. BBB. CCC.178 extensible 80
IP nat inside source static tcp 10.128.7.1 443 AAA. BBB. CCC.178 extensible 443
IP nat inside source static tcp 10.128.7.1 8333 AAA. BBB. CCC.178 extensible 8333
IP nat inside source static tcp 10.128.7.2 25 AAA. BBB. Expandable 25 CCC.179
IP nat inside source static tcp 10.128.7.2 80 AAA. BBB. CCC.179 extensible 80
IP nat inside source static tcp 10.128.7.2 443 AAA. BBB. CCC.179 extensible 443
IP nat inside source static tcp 10.128.7.2 8333 AAA. BBB. CCC.179 extensible 8333
IP nat inside source static tcp 10.128.7.3 25 AAA. BBB. Expandable 25 CCC.180
IP nat inside source static tcp 10.128.7.3 80 AAA. BBB. CCC.180 extensible 80
IP nat inside source static tcp 10.128.7.3 443 AAA. BBB. CCC.180 extensible 443
IP nat inside source static tcp 10.128.7.3 8333 AAA. BBB. CCC.180 extensible 8333
IP nat inside source static tcp 10.128.7.4 25 AAA. BBB. Expandable 25 CCC.181
IP nat inside source static tcp 10.128.7.4 80 AAA. BBB. CCC.181 extensible 80
IP nat inside source static tcp 10.128.7.4 443 AAA. BBB. CCC.181 extensible 443
IP nat inside source static tcp 10.128.7.4 8333 AAA. BBB. CCC.181 extensible 8333
IP nat inside source static tcp 10.128.7.5 25 AAA. BBB. Expandable 25 CCC.182
IP nat inside source static tcp 10.128.7.5 80 AAA. BBB. CCC.182 extensible 80
IP nat inside source static tcp 10.128.7.5 443 AAA. BBB. CCC.182 extensible 443
IP nat inside source static tcp 10.128.7.5 8333 AAA. BBB. CCC.182 extensible 8333
IP nat inside source static tcp 10.128.7.6 25 AAA. BBB. Expandable 25 CCC.183
IP nat inside source static tcp 10.128.7.6 80 AAA. BBB. CCC.183 extensible 80
IP nat inside source static tcp 10.128.7.6 443 AAA. BBB. CCC.183 extensible 443
IP nat inside source static tcp 10.128.7.6 8333 AAA. BBB. CCC.183 extensible 8333
IP nat inside source static tcp 10.128.7.7 25 AAA. BBB. Expandable 25 CCC.184
IP nat inside source static tcp 10.128.7.7 80 AAA. BBB. CCC.184 extensible 80
IP nat inside source static tcp 10.128.7.7 443 AAA. BBB. CCC.184 extensible 443
IP nat inside source static tcp 10.128.7.7 8333 AAA. BBB. CCC.184 extensible 8333
IP nat inside source static tcp 10.128.7.8 25 AAA. BBB. Expandable 25 CCC.185
IP nat inside source static tcp 10.128.7.8 80 AAA. BBB. CCC.185 extensible 80
IP nat inside source static tcp 10.128.7.8 443 AAA. BBB. CCC.185 extensible 443
IP nat inside source static tcp 10.128.7.8 8333 AAA. BBB. CCC.185 extensible 8333
IP nat inside source static tcp 10.128.7.9 25 AAA. BBB. Expandable 25 CCC.186
IP nat inside source static tcp 10.128.7.9 80 AAA. BBB. CCC.186 extensible 80
IP nat inside source static tcp 10.128.7.9 443 AAA. BBB. CCC.186 extensible 443
IP nat inside source static tcp 10.128.7.9 8333 AAA. BBB. CCC.186 extensible 8333
IP nat inside source static tcp 10.128.7.10 25 AAA. BBB. Expandable 25 CCC.187
IP nat inside source static tcp 10.128.7.10 80 AAA. BBB. CCC.187 extensible 80
IP nat inside source static tcp 10.128.7.10 443 AAA. BBB. CCC.187 extensible 443
IP nat inside source static tcp 10.128.7.10 8333 AAA. BBB. CCC.187 extensible 8333
IP nat inside source static tcp 10.128.7.11 25 AAA. BBB. Expandable 25 CCC.188
IP nat inside source static tcp 10.128.7.11 80 AAA. BBB. CCC.188 extensible 80
IP nat inside source static tcp 10.128.7.11 443 AAA. BBB. CCC.188 extensible 443
IP nat inside source static tcp 10.128.7.11 8333 AAA. BBB. CCC.188 extensible 8333
IP nat inside source static tcp 10.128.7.12 25 AAA. BBB. Expandable 25 CCC.189
IP nat inside source static tcp 10.128.7.12 80 AAA. BBB. CCC.189 extensible 80
IP nat inside source static tcp 10.128.7.12 443 AAA. BBB. CCC.189 extensible 443
IP nat inside source static tcp 10.128.7.12 8333 AAA. BBB. CCC.189 extensible 8333
!
Guest-ACL extended IP access list
deny ip any 10.128.7.0 0.0.0.255
deny ip any 10.128.150.0 0.0.0.255
allow an ip
IP Internet traffic inbound-ACL extended access list
allow udp any eq bootps any eq bootpc
permit any any icmp echo
permit any any icmp echo response
permit icmp any any traceroute
allow a gre
allow an esp
!
access-list 1 permit 10.128.7.0 0.0.0.255
access-list 1 permit 10.128.150.0 0.0.0.255
access-list 1 permit 10.128.1.0 0.0.0.255
access-list 2 allow 10.0.0.0 0.255.255.255
access-list 2 refuse any
access-list 101 permit ip 10.128.7.0 0.0.0.255 any
access-list 101 permit ip 10.128.150.0 0.0.0.255 any
access-list 101 permit ip 10.128.1.0 0.0.0.255 any
Dialer-list 1 ip Protocol 1
!
!
!
!
format of server RADIUS attribute 32 include-in-access-req hour
RADIUS-server host 10.128.7.5 auth-port 1645 acct-port 1646 borders 7 xxxxx
RADIUS vsa server send accounting
!
control plan
!
IP route 10 bridge
IP road bridge 20
IP road bridge 30
Banner motd ^.
Unauthorized access prohibited. *
All access attempts are logged! ***************

^
!
Line con 0
password 7 xxxx
no activation of the modem
line to 0
line vty 0 4
access-class 2
privilege level 15
transport input telnet ssh
!
max-task-time 5000 Planner
AAA.BBB.CCC.ddd NTP server
end

Erik,

The address pool you are talking about is to assign to the customer or the public router interface? If you want to set up your vpn client software point a full domain name instead of an IP address that you can do it too long you can ensure the use of the name is resolved by a DNS SERVER.

The range of addresses that you can be asigned to your Dialer interface will depend on your ISP.

-Butterfly

ASA problem inside the VPN client routing

Hello

I have a problem where I can't reach the VPN clients with their vpn IP pool from the inside or the asa itself. Connect VPN clients can access internal network very well. I have no nat configured for the pool of vpn and packet trace crypt packages and puts it into the tunnel. I'm not sure what's wrong.

Here are a few relevant config:

network object obj - 192.168.245.0

192.168.245.0 subnet 255.255.255.0

192.168.245.1 - 192.168.245.50 vpn IP local pool

NAT (inside, outside) static source any any destination static obj - 192.168.245.0 obj - 192.168.245.0 no-proxy-arp-search to itinerary

Out of Packet trace:

Firewall # entry packet - trace inside the x.x.x.x icmp 8 0 192.168.245.33

Phase: 1

Type: ACCESS-LIST

Subtype:

Result: ALLOW

Config:

Implicit rule

Additional information:

MAC access list

Phase: 2

Type:-ROUTE SEARCH

Subtype: entry

Result: ALLOW

Config:

Additional information:

in 192.168.245.33 255.255.255.255 outside

Phase: 3

Type: ACCESS-LIST

Subtype: Journal

Result: ALLOW

Config:

Access-group acl-Interior interface inside

access list acl-Interior extended icmp permitted an echo

Additional information:

Phase: 4

Type: IP-OPTIONS

Subtype:

Result: ALLOW

Config:

Additional information:

Phase: 5

Type: INSPECT

Subtype: np - inspect

Result: ALLOW

Config:

Additional information:

Phase: 6

Type:

Subtype:

Result: ALLOW

Config:

Additional information:

Phase: 7

Type: NAT

Subtype:

Result: ALLOW

Config:

NAT (inside, outside) static source any any destination static obj - 192.168.245.0

obj - 192.168.245.0 no-proxy-arp-search to itinerary

Additional information:

Definition of static 0/x.x.x.x-x.x.x.x/0

Phase: 8

Type: VPN

Subtype: encrypt

Result: ALLOW

Config:

Additional information:

Phase: 9

Type: CREATING STREAMS

Subtype:

Result: ALLOW

Config:

Additional information:

New workflow created with the 277723432 id, package sent to the next module

Result:

input interface: inside

entry status: to the top

entry-line-status: to the top

output interface: outside

the status of the output: to the top

output-line-status: to the top

Action: allow

There is no route to the address pool of vpn. Maybe that's the problem? I don't know than that used to work before we went to 8.4.

Check if the firewall is enabled on your host from the client ravpn and blocking your pings.

VPN client with counterpart on secondary ip address on the public interface of the router

Hello

On our office LAN, we have a Linux server than it hosting a VPN connection to a remote client.

Do this to ISAKMP card on our Cisco router port connections to the internal ip address of the Linux host.

However, we now want to allow our users to establish VPN connections to our local network using the unit of Cisco VPN Client.

Of course, this would present challenges, as the ISAKMP our router port is mapped through an internal host.

So, we tried to set up a secondary ip address on the router and VPN clients to connect to that.

What we see in our newspapers is as follows:

Phase 1 is very well established, and the VPN Client prompts the user for a user name and password.

Authentication of the phase 2 starts, but the router says it's is not to receive a proposal of hash of the client.

185 12:18:06.943 09/03/11 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:no_proposal_chosen)="" from="">

(in this case, where x.x.x.x is the secondary ip address on the public interface)

After that, the Phase 1 SA is removed and the connection fails.

My understanding is that the Phase 2 negotiation takes place with the ip address assigned to the client in Phase 1, which suggests that the problem occurs because the client communicates with the main on the interface ip address, and no secondary ip address.

When remove us the mapping of port isakmp and the VPN client to connect to the primary ip address, everything works fine.

Question:

It is possible to establish 2 router VPN Client uses a secondary ip address?

If not, is there some way I can implement the port mapping so that it occurs, the connection comes from a specific ip address?

Garreth

Should be supported on IOS.

The command is crypto ctcp port...

Check this link:

http://www.Cisco.com/en/us/prod/collateral/iosswrel/ps6537/ps6586/ps6635/ps6659/prod_white_paper0900aecd8061e2b3.html

Federico.

Routing problem between the VPN Client and the router's Ethernet device

Hello

I have a Cisco 1721 in a test environment.

A net 172.16.0.0/19 simulates the Internet and a net 192.168.1.0/24 simulates the net, the VPN tunnel must go to (intranet).

The net 172.16.0.0 depends on the router 0 FastEthernet, Intranet (VPN) hangs on Ethernet 0.

The configuration was inspired form the sample Configuration

"Configuring the Client VPN Cisco 3.x for Windows to IOS using Local extended authentication"

and the output of the ConfigMaker configuration.

Authentication and logon works. Client receives an IP address from the pool. But there's a routing problem

side of routers. Ping client-side - do not work (the VPN client statistics that count encrypt them packets, but not to decrypt).

Ping the router works too, but decrypt and encrypt customer statistics in VPN packets count progressive

(customer has a correct route and return ICMP packets to the router).

The question now is:

How to route packets between the Tunnel and an Ethernet device (Ethernet 0)?

conf of the router is attached - hope that's not too...

Thanks & cordially

Thomas Schmidt

-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.- snipp .-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.

!

version 12.2

horodateurs service debug uptime

Log service timestamps uptime

encryption password service

!

!

host name * moderator edit *.

!

enable secret 5 * moderator edit *.

!

!

AAA new-model

AAA authentication login userauthen local

AAA authorization groupauthor LAN

!

! only for the test...

!

username cisco password 0 * moderator edit *.

!

IP subnet zero

!

audit of IP notify Journal

Max-events of po verification IP 100

!

crypto ISAKMP policy 3

3des encryption

preshared authentication

Group 2

!

ISAKMP crypto client configuration group 3000client

key cisco123

pool ippool

!

! We do not want to divide the tunnel

! ACL 108

!

Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

!

Crypto-map dynamic dynmap 10

Set transform-set RIGHT

!

map clientmap client to authenticate crypto list userauthen

card crypto clientmap isakmp authorization list groupauthor

client configuration address map clientmap crypto answer

10 ipsec-isakmp crypto map clientmap Dynamics dynmap

!

interface Ethernet0

no downtime

Description connected to VPN

IP 192.168.1.1 255.255.255.0

full-duplex

IP access-group 101 in

IP access-group 101 out

KeepAlive 10

No cdp enable

!

interface Ethernet1

no downtime

address 192.168.3.1 IP 255.255.255.0

IP access-group 101 in

IP access-group 101 out

full-duplex

KeepAlive 10

No cdp enable

!

interface FastEthernet0

no downtime

Description connected to the Internet

IP 172.16.12.20 255.255.224.0

automatic speed

KeepAlive 10

No cdp enable

!

! This access group is also only for test cases!

!

no access list 101

access list 101 ip allow a whole

!

local pool IP 192.168.10.1 ippool 192.168.10.10

IP classless

IP route 0.0.0.0 0.0.0.0 172.16.12.20

enable IP pim Bennett

!

Line con 0

exec-timeout 0 0

password 7 * edit from moderator *.

line to 0

line vty 0 4

!

end

^-^-^-^-^-^-^-^-^-^-^-^-^- snapp ^-^-^-^-^-^-^-^-^-^-^-^-^-^-

Thomas,

Can't wait to show something that might be there, but I don't see here. You do not have the card encryption applied to one of the interfaces, perhaps it was not copied. Assuming your description you do it, or should it be, applied to the fa0 and you are connected. Try how you ping? Since the router or a device located on E0? If you ping the router, you will need to do an extended ping of E0 to the ip address of the client has been assigned. If your just ping the router without the extension, you will get sales and decrypts that you declare on the client. Have you tried to ping from the client to interface E0? Your default route on the router is pointing to fa0? You have a next hop to affect? You have several NIC on the client pc? Turn off your other network cards to check that you don't have a problem with routing on the client if you have more than one.

Kurtis Durrett

Maintenance of the internal DNS after connecting to the VPN Client

We connect to the VPN client, all day and I wanted to know if there is a way to continue to use our internal LAN DNS when you are connected. For example, when I connect to the VPN client, our mail server internal and the dns resolves the public IP address.

Thank you

You can set up the split-dns service, but which can be configured at the vpn your client device, because you only connect with vpn client and normally politicians vpn client get pushed vpn headend unit.

Here is the split-dns command if your customer comes to run ASA firewall, and they allow you to configure:

http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/S8.html#wp1404571

Codes and 80041002 repeated error 8004102f trying to set up the Live Family Safety.

Codes and 80041002 repeated error 8004102f trying to set up the Live Family Safety. I uninstalled then reinstalled emissions live as suggested here in the forum, but nothing helped. I always get error codes. I'm trying to set up on my Vista operating system with os XP of my daughter.

Please go to windows live solution Center

http://www.windowslivehelp.com/product.aspx?ProductID=4

If this post can help solve your problem, please click the 'Mark as answer"If you find it useful, mark it as useful by clicking the 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

The VPN client VPN connection behind other PIX PIX

I have the following problem:

I wanted to establish the VPN connection the client VPN to PIX on GPRS / 3G, but I didn t have a bit of luck with PIX IOS version 6.2 (2).

So I upgraded PIX to 6.3 (4) to use NAT - T and VPN client to version 4.0.5

I have configured PIX with NAT-T(isakmp nat-traversal 20), but I still had a chance, he would not go through the 1st phase. As soon as I took nat-traversal isakmp off he started working, and we can connect to our servers.

Now, I want to connect to the VPN client behind PIX to our customer PIX network. VPN connection implements without problem, but we can not access the servers. If I configure NAT - T on the two PIX, or only on the customer PIX or only on our PIX, no VPN connection at all.

If I have to connect VPN client behind PIX to the customer's network and you try to PING DNS server for example, on our PIX, I have following error:

305006: failed to create of portmap for domestic 50 CBC protocol translation: dst outside:194.x.x.x 10.10.1.x

194.x.x.x is our customer s address IP PIX

I understand that somewhere access list is missing, but I can not understand.

Of course, I can configure VPN site to site, but we have few customers and take us over their servers, so it'd just connect behind PIX VPN and client connection s server, instead of the first dial-in and then establish a VPN connection.

Can you please help me?

Thank you in advan

The following is extracted from ASK THE DISCUSSION FORUM of EXPERTS with Glenn Fullage of Cisco.

I've cut and pasted here for you to read, I think that the problem mentioned below:

Question:

Hi Glenn,.

Following is possible?

I have the vpn client on my PC, my LAN is protected by a pix. I can launch the vpn client to connect to remote pix. Authenticates the vpn client and the remote pix makes my PC with the assigned ip appropriate to its pool of ip address.

The problem that I am facing is that I can not anything across the pix remote ping from my PC which is behind my pix. Can you please guide me what I have to do to make this work, if it is possible?

My PC has a static ip address assigned with the default gateway appropriate pointing to my s pix inside interface.

Thank you very much for any help provided in advance.

Response from Glenn:

First of all, make sure that the VPN connection works correctly when the remote PC is NOT behind a PIX. If that works fine, but then breaks when put behind a PIX, it is probably that the PIX is PAT, which usually breaks IPSec. Add the following command on your PIX VPN client is behind:

fixup protocol esp-ike

See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/df.htm#wp1067379 for more details.

If it still has issues, you can turn on NAT - T on the remote PIX that ends the VPN, the client and the remote PIX must encapsulate then all IPSec in UDP packets that your PIX will be able to PA correctly. Add the following command on the remote PIX:

ISAKMP nat-traversal

See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/gl.htm#wp1027312 for more details.

NAT - T is a standard for the encapsulation of the UDP packets inot IETF IPSec packets.

ESP IPSec (Protocol that use your encrypted data packets) is an IP Protocol, it is located just above IP, rather than being a TCP or UDP protocol. For this reason, it has no TCP/UDP port number.

A lot of features that make the translation of address of Port (PAT) rely on a single to PAT TCP/UDP source port number ' ing. Because all traffic is PAT would be at the same source address, must be certain uniqueness to each of its sessions, and most devices use the port number TCP/UDP source for this. Because IPSec doesn't have one, many features PAT fail to PAT it properly or at all, and the data transfer fails.

NAT - T is enabled on both devices of the range, they will determine during the construction of the tunnel there is a PAT/NAT device between them, and if they detect that there is, they automatically encapsulate every IPSec packets in UDP packets with a port number of 4500. Because there is now a port number, PAT devices are able to PAT it correctly and the traffic goes normally.

Hope that helps.

The VPN client connection

Is it possible to configure the VPN client to set up some sort of login and password so when you run, connects automatically without writing the user name and password.

This must be the vpn client without making any changes on the vpn server.

No idea how to do this?

Kind regards

to 4.0.2 4.6 & 4.8 Yes - in the profile .pcf file, make sure that

SaveUserPassword = 1

This will keep the user name & password in the profile, when you click on it - it should fine connection.

You must also activate the user store password: -.

In the pix / asa - under the client VPN profile:-

allow password-storage

HTH.

The Vpn Client ASDM download

I was trying to the vpn Wizard ASDM allows you to download the new client anyconnect 4.2 and I got errors saying that the file is not valid.

Should which file I download in order for customers to download the vpn client.

I have asa x 5506

Hello

You must use the anyconnect file you get from cisco.com or Cisco partner and download, the .pkg file extension

for example:

# poster run | grep anyconnect
AnyConnect image disk0:/anyconnect-win-4.2.01022-k9.pkg 1

HTH

Samer.

Is there a 64-bit version of the VPN Client for the coming of Vista?

Is there a 64-bit version of the VPN Client for Vista to come for VPN 3000 series concentrators?

Hello

A bit is a tour here.

According to Cisco:

Install the VPN Client on a Vista 64 bit Machine will cause an error 1721

Cisco IPSec Client does not support 64-bit. If the user requires a 64-bit support, upgrade path is to use the Cisco AnyConnect VPN Client instead, that supports 64-bit. Note that the AnyConnect Client supports only SSL VPN (CSCsi26069) connections.

So if you want to go with 64-bit, you need SSL support on the VPN 3000 series and replace all IPSEC with SSL connections.

Please rate if this helped.

Kind regards

Daniel

The VPN client user authentication

When users connect to our network remotely via VPN user name field is already filled with the last person who logged. I know that they just delete the username and enter their own, but is there a way the client can be configured to where the username field will be always empty for all those who want access to the network via VPN? We have an ASA 5510 with version 7.0 (8) and a windows 2003 with IAS server for windows authentication. Thank you!

Hello

In FCP, you can configure a single line is not editable by the user (or the vpn client).

Simply insert an attack! Like this

! Username =

! SaveUserPassword = 0

! UserPassword =

! enc_UserPassword =

Subsequently the vpn client will not save registrations for these settings more.

Group to be installed on the VPN Client

We run IOS 8.2 (2). We configure VPN groups to authenticate locally to the ASA. We have about 10 different groups (marketing, engineering, accounting, technical support, etc.) that I need the installation which is no problem. My problem is that I have to configure 10 different groups on the VPN client based on their user name. Is it possible to set up a generic group such as everyone on the VPN client and the users will no longer have access to resources based on their user name when they connect to the VPN client?

Please let me know if you have any questions or need additional information.

Thank you.

Laura

Hi Laura,

You can have all users that connect to the same group.

Then, individually on each user, create a VPN filter...

username test attributes

VPN-filter...

Federico.

Trying to set up the VPN Client with crossed on ASA5510

Similar Questions

Maybe you are looking for